A straight-forward conversion of the xlnx_versal_virt boot
test to the functional framework.
Message-ID: <20241206102358.1186644-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This file should belong to the R2D machine in the MAINTAINERS file.
Message-ID: <20241204071120.663446-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When running "make -j$(nproc) check SPEED=thorough", the sh4_tuxrun
test is timing out for me, and using TIMEOUT_MULTIPLIER I can see
that it clearly takes more than 100 seconds to finish. Thus increase
the timeout setting of this test to avoid the problem.
Message-ID: <20241204070757.663119-1-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This commit introduces the definition of the gen17a/gen17b CPU model.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Message-ID: <20241206122751.189721-16-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The PLO-extension facility introduces numerous locking related
subfunctions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-15-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The PLO functions 0, 4, 8, 12, 16, and 20 use 32-bit registers
values. The plo-*gr variants use 64-bit instead and, thus, correct
the wording.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-14-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The sequential instruction fetching facility provides few guarantees,
for example, to avoid stop machine calls on enabling/disabling kprobes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-13-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This facility indicates reduced support for noncontrained
transactional-execution.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-12-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This facility introduces new capabilities for the signed-pack-decimal
format.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-11-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This facility introduces few new instructions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-10-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Vector Enhancements facility 3 introduces new instructions and
extends support for doubleword/quadword elements.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-9-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Concurrent-functions facility introduces the new instruction
Perform Functions with Concurrent Results (PFCR) with few subfunctions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-8-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This linux headers update includes required changes for
the gen17 CPU model.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241206122751.189721-7-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Introduce a new PTFF subfunction to query-stamp events.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Message-ID: <20241206122751.189721-6-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
MSA12 changes the KIMD/KLMD instruction format for SHA3/SHAKE.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Message-ID: <20241206122751.189721-4-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
MSA11 introduces new HMAC subfunctions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Message-ID: <20241206122751.189721-3-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
MSA10 introduces new AES XTS subfunctions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Message-ID: <20241206122751.189721-2-brueckner@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
QEMU takes contributions via the mailing list, so while you can edit a
file on gitlab and then switch to the terminal to send a patch, the
wording 'Edit on GitLab' strongly suggests we take merge requests.
Switching back to "View page source" is a more agnostic term that does
not imply a particular contribution approach, that we had used in QEMU
before:
commit 73e6aec652
Author: Marc-André Lureau <marcandre.lureau@redhat.com>
Date: Tue Mar 23 15:53:28 2021 +0400
sphinx: adopt kernel readthedoc theme
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-ID: <20241209163506.2089961-1-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Follow the other architecture targets by adding extra macros for
defining a versioned machine type as the latest. This reduces the
size of the changes when introducing new machine types at the start
of each release cycle.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240910163041.3764176-1-berrange@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-ID: <20241126103005.3794748-2-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This series has 2 fixes:
- Fix to keep serial@90000000 as default
- Fixed undercounting of TTCR in continuous mode
-----BEGIN PGP SIGNATURE-----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=guIi
-----END PGP SIGNATURE-----
Merge tag 'pull-or1k-20241203' of https://github.com/stffrdhrn/qemu into staging
OpenRISC updates for 9.2.0
This series has 2 fixes:
- Fix to keep serial@90000000 as default
- Fixed undercounting of TTCR in continuous mode
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE2cRzVK74bBA6Je/xw7McLV5mJ+QFAmdO56EACgkQw7McLV5m
# J+T8BRAAxZMH4ykdRJBmYiFVOsYKagcdT6GGBHL44FGeQSr1lNyoU0Rn5r6v5GHe
# Nwq7DTeZlKoVji5GXki53mGrwENXr00m+xfc9ACMoWr5IM6McQUPXlQAQ/50fIGs
# lzXMZH/4EdPIVkkpCi+y8FLYw02oQg61U9G0HW02lQJy4Y4mudtvQFGzJ7f3SIZ3
# EkKn5YLG0bqszq/amFNLQXlbnq3yI5zfcMHhHx0KuDsm2yNhrNA+AJP8tLI3JlxL
# +0YIA+fWuxQzz8Zu9+ckc8VAV83HIgQpXVzI6rQxdSwbmRgUu9ITO09ZmxaDHZF6
# sDI6K3VouyaHJVkvu4coDajpYTjHLE26c9LAlaVBpgdnmnYy4vlndEqbfaBqOouX
# n0N2wJ3IGouIw7AnB9dTaZhM/Uo09hZKDr6kCm3hLfPn2+vi3yxsbwVwLaOpH3G3
# kQ5ZFKjoA7XWOaXGOUMcmhByXkSxja+pSBppB58vJAFyVp73HYIpea3/q1Zd8S4S
# noJoqxDtD2zf26bDBIe83pUEnSnL8fAcsh3rlQP8HrWYhU7ZulVSE1ZvPkPgDpkY
# LVCPautTElsMp2Mg4a2oODGvSDN4/5h2dp6TaK4Qep92HHFOwPZQBQW607VwWR5N
# II8dB/l8PluKkgZ3ymhP1p9JAAZFe9a2cMmegRIiM74PkPty0kk=
# =guIi
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 03 Dec 2024 11:12:33 GMT
# gpg: using RSA key D9C47354AEF86C103A25EFF1C3B31C2D5E6627E4
# gpg: Good signature from "Stafford Horne <shorne@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: D9C4 7354 AEF8 6C10 3A25 EFF1 C3B3 1C2D 5E66 27E4
* tag 'pull-or1k-20241203' of https://github.com/stffrdhrn/qemu:
hw/openrisc: Fixed undercounting of TTCR in continuous mode
hw/openrisc/openrisc_sim: keep serial@90000000 as default
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter points out double underscore prefix names tend to be reserved
for the system. Clean these up.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20240828043337.14587-3-npiggin@gmail.com>
qemu_chardev_set_replay() was being called in chardev creation to
set up replay parameters even if the chardev is NULL.
A segfault can be reproduced by specifying '-serial chardev:bad' with
an rr=record mode.
Fix this with a NULL pointer check.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: Coverity CID 1559470
Fixes: 4c193bb129 ("chardev: set record/replay on the base device of a muxed device")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20240828043337.14587-2-npiggin@gmail.com>
When testing with a HVF-only binary, we get:
3/12 qemu:func-quick+func-aarch64 / func-aarch64-version ERROR 0.29s exit status 1
stderr:
Traceback (most recent call last):
File "tests/functional/test_version.py", line 22, in test_qmp_human_info_version
self.vm.launch()
File "machine/machine.py", line 461, in launch
raise VMLaunchFailure(
qemu.machine.machine.VMLaunchFailure: ConnectError: Failed to establish session: EOFError
Exit code: 1
Command: build/qemu-system-aarch64 -display none -vga none -chardev socket,id=mon,fd=5 -mon chardev=mon,mode=control -machine none -nodefaults
Output: qemu-system-aarch64: No accelerator selected and no default accelerator available
Fix by checking for HVF in configure_accelerators() and using
it by default when no other accelerator is available.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20241203094232.62232-1-philmd@linaro.org>
This test would have identified the crash caused by the addition of new
balloon stats fields.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20241129135507.699030-4-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This test file is expected to be extended for arbitrary virtio-balloon
related tests, not merely those discovered by fuzzing.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Message-ID: <20241129135507.699030-3-berrange@redhat.com>
[PMD: Update MAINTAINERS]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
balloon_stats_get_all will iterate over guest stats upto the max
VIRTIO_BALLOON_S_NR value, calling visit_type_uint64 to populate
the QObject dict. The dict keys are obtained from the static
array balloon_stat_names which is VIRTIO_BALLOON_S_NR in size.
Unfortunately the way that array is declared results in any
unassigned stats getting a NULL name, which will then cause
visit_type_uint64 to trigger an assert in qobject_output_add_obj.
The balloon_stat_names array was fortunately fully populated with
names until recently:
commit 0d2eeef77a
Author: Bibo Mao <maobibo@loongson.cn>
Date: Mon Oct 28 10:38:09 2024 +0800
linux-headers: Update to Linux v6.12-rc5
pulled a change to include/standard-headers/linux/virtio_balloon.h
which increased VIRTIO_BALLOON_S_NR by 6, and failed to add the new
names to balloon_stat_names.
This commit fills in the missing names, and uses a static assert to
guarantee that any future changes to VIRTIO_BALLOON_S_NR will cause
a build failure until balloon_stat_names is updated.
This problem was detected by the Cockpit Project's automated
integration tests on QEMU 9.2.0-rc1.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=2329448
Fixes: 0d2eeef77a ("linux-headers: Update to Linux v6.12-rc5")
Reported-by: Martin Pitt <mpitt@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20241129135507.699030-2-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The 'pci-vga' device allow setting a 'big-endian-framebuffer'
property since commit 3c2784fc86 ("vga: Expose framebuffer
byteorder as a QOM property"). Similarly, the 'virtio-vga'
device since commit 8be61ce2ce ("virtio-vga: implement
big-endian-framebuffer property").
Both call vga_common_reset() in their reset handler, respectively
pci_secondary_vga_reset() and virtio_vga_base_reset_hold(), which
reset 'big_endian_fb', overwritting the property. This is not
correct: the hardware is expected to keep its configured
endianness during resets.
Move 'big_endian_fb' assignment from vga_common_reset() to
vga_common_init() which is called once when the common VGA state
is initialized.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Message-Id: <20241129101721.17836-2-philmd@linaro.org>
In riscv_cpu_do_interrupt() we use the 'cause' value we got out of
cs->exception as a shift value. However this value can be larger
than 31, which means that "1 << cause" is undefined behaviour,
because we do the shift on an 'int' type.
This causes the undefined behaviour sanitizer to complain
on one of the check-tcg tests:
$ UBSAN_OPTIONS=print_stacktrace=1:abort_on_error=1:halt_on_error=1 ./build/clang/qemu-system-riscv64 -M virt -semihosting -display none -device loader,file=build/clang/tests/tcg/riscv64-softmmu/issue1060
../../target/riscv/cpu_helper.c:1805:38: runtime error: shift exponent 63 is too large for 32-bit type 'int'
#0 0x55f2dc026703 in riscv_cpu_do_interrupt /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/clang/../../target/riscv/cpu_helper.c:1805:38
#1 0x55f2dc3d170e in cpu_handle_exception /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/clang/../../accel/tcg/cpu-exec.c:752:9
In this case cause is RISCV_EXCP_SEMIHOST, which is 0x3f.
Use 1ULL instead to ensure that the shift is in range.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 1697837ed9 ("target/riscv: Add M-mode virtual interrupt and IRQ filtering support.")
Fixes: 40336d5b1d ("target/riscv: Add HS-mode virtual interrupt and IRQ filtering support.")
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241128103831.3452572-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The 'maxmem' parameter parsed on the command line is held in uint64_t
and then assigned to the MachineState field that is 'ram_addr_t'. This
assignment will wrap on 32-bit hosts, silently changing the user's
config request if it were over-sized.
Improve the existing diagnositics for validating 'size', and add the
same diagnostics for 'maxmem'
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Tested-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-ID: <20241127114057.255995-1-berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Also: add mapping for "quic_bcain@quicinc.com" which was ~briefly
used for some replies to mailing list traffic.
Signed-off-by: Brian Cain <bcain@quicinc.com>
Signed-off-by: Brian Cain <brian.cain@oss.qualcomm.com>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20241123164641.364748-2-bcain@quicinc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When building QEMU configure with --disable-gtk --disable-cocoa
on macOS we get:
User interface
Cocoa support : NO
SDL support : YES 2.30.5
SDL image support : NO
GTK support : NO
pixman : YES 0.42.2
VTE support : NO
PNG support : YES 1.6.43
VNC support : YES
VNC SASL support : YES
VNC JPEG support : YES 3.0.3
spice protocol support : YES 0.14.4
spice server support : NO
curses support : YES
brlapi support : NO
User defined options
cocoa : disabled
docs : disabled
gtk : disabled
../system/main.c:30:10: fatal error: 'SDL.h' file not found
30 | #include <SDL.h>
| ^~~~~~~
1 error generated.
Fix by adding the SDL dependency to main.c it's CFLAGS contains
the SDL include directory.
Fixes: 64ed6f92ff ("meson: link emulators without Makefile.target")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20241120114943.85080-1-philmd@linaro.org>
Song Gao is will be sick leave for a long time, I apply for maintainer
for LoongArch Virt Machine during this period, LoongArch TCG keeps unchanged
since I am not familiar with it. The maintainer duty will transfer to him
after he comes back to work.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20241112073714.1953481-1-maobibo@loongson.cn>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
These warnings are breaking some build configurations since 2 months
now (https://gitlab.com/qemu-project/qemu/-/issues/2575):
ui/cocoa.m:662:14: error: 'CVDisplayLinkCreateWithCGDisplay' is deprecated: first deprecated in macOS 15.0 - use NSView.displayLink(target:selector:), NSWindow.displayLink(target:selector:), or NSScreen.displayLink(target:selector:) [-Werror,-Wdeprecated-declarations]
662 | if (!CVDisplayLinkCreateWithCGDisplay(display, &displayLink)) {
| ^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/CoreVideo.framework/Headers/CVDisplayLink.h:89:20: note: 'CVDisplayLinkCreateWithCGDisplay' has been explicitly marked deprecated here
89 | CV_EXPORT CVReturn CVDisplayLinkCreateWithCGDisplay(
| ^
ui/cocoa.m:663:29: error: 'CVDisplayLinkGetNominalOutputVideoRefreshPeriod' is deprecated: first deprecated in macOS 15.0 - use NSView.displayLink(target:selector:), NSWindow.displayLink(target:selector:), or NSScreen.displayLink(target:selector:) [-Werror,-Wdeprecated-declarations]
663 | CVTime period = CVDisplayLinkGetNominalOutputVideoRefreshPeriod(displayLink);
| ^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/CoreVideo.framework/Headers/CVDisplayLink.h:182:18: note: 'CVDisplayLinkGetNominalOutputVideoRefreshPeriod' has been explicitly marked deprecated here
182 | CV_EXPORT CVTime CVDisplayLinkGetNominalOutputVideoRefreshPeriod( CVDisplayLinkRef CV_NONNULL displayLink );
| ^
ui/cocoa.m:664:13: error: 'CVDisplayLinkRelease' is deprecated: first deprecated in macOS 15.0 - use NSView.displayLink(target:selector:), NSWindow.displayLink(target:selector:), or NSScreen.displayLink(target:selector:) [-Werror,-Wdeprecated-declarations]
664 | CVDisplayLinkRelease(displayLink);
| ^
/Library/Developer/CommandLineTools/SDKs/MacOSX.sdk/System/Library/Frameworks/CoreVideo.framework/Headers/CVDisplayLink.h:249:16: note: 'CVDisplayLinkRelease' has been explicitly marked deprecated here
249 | CV_EXPORT void CVDisplayLinkRelease( CV_RELEASES_ARGUMENT CVDisplayLinkRef CV_NULLABLE displayLink );
| ^
3 errors generated.
For the next release, ignore the warnings using #pragma directives.
At least until we figure the correct new API usage.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Phil Dennis-Jordan <phil@philjordan.eu>
Tested-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-Id: <20241121131954.98949-1-philmd@linaro.org>
We used to only have a single UART on the platform and it was located at
address 0x90000000. When the number of UARTs was increased to 4, the
first UART remained at it's location, but instead of being the first one
to be registered, it became the last.
This caused QEMU to pick 0x90000300 as the default UART, which broke
software that hardcoded the address of 0x90000000 and expected it's
output to be visible when the user configured only a single console.
This caused regressions[1] in the barebox test suite when updating to a
newer QEMU. As there seems to be no good reason to register the UARTs in
inverse order, let's register them by ascending address, so existing
software can remain oblivious to the additional UART ports.
Changing the order of uart registration alone breaks Linux which
was choosing the UART at 0x90000300 as the default for ttyS0. To fix
Linux we fix three things in the device tree:
1. Define stdout-path only one time for the first registered UART
instead of incorrectly defining for each UART.
2. Change the UART alias name from 'uart0' to 'serial0' as almost all
Linux tty drivers look for an alias starting with "serial".
3. Add the UART nodes so they appear in the final DTB in the
order starting with the lowest address and working upwards.
In summary these changes mean that the QEMU default UART (serial_hd(0))
is now setup where:
* serial_hd(0) is the lowest-address UART
* serial_hd(0) is listed first in the DTB
* serial_hd(0) is the /chosen/stdout-path one
* the /aliases/serial0 alias points at serial_hd(0)
[1]: https://lore.barebox.org/barebox/707e7c50-aad1-4459-8796-0cc54bab32e2@pengutronix.de/T/#m5da26e8a799033301489a938b5d5667b81cef6ad
[stafford: Change to serial0 alias and update change message, reverse
uart registration order]
Fixes: 777784bda4 ("hw/openrisc: support 4 serial ports in or1ksim")
Cc: qemu-stable@nongnu.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20241203110536.402131-2-shorne@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In the existing design, TTCR is prone to undercounting when running in
continuous mode. This manifests as a timer interrupt appearing to
trigger a few cycles prior to the deadline set in SPR_TTMR_TP.
When the timer triggers, the virtual time delta in nanoseconds between
the time when the timer was set, and when it triggers is calculated.
This nanoseconds value is then divided by TIMER_PERIOD (50) to compute
an increment of cycles to apply to TTCR.
However, this calculation rounds down the number of cycles causing the
undercounting.
A simplistic solution would be to instead round up the number of cycles,
however this will result in the accumulation of timing error over time.
This patch corrects the issue by calculating the time delta in
nanoseconds between when the timer was last reset and the timer event.
This approach allows the TTCR value to be rounded up, but without
accumulating error over time.
Signed-off-by: Joel Holdsworth <jholdsworth@nvidia.com>
[stafford: Incremented version in vmstate_or1k_timer, checkpatch fixes]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Message-ID: <20241203110536.402131-3-shorne@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In the existing design, TTCR is prone to undercounting when running in
continuous mode. This manifests as a timer interrupt appearing to
trigger a few cycles prior to the deadline set in SPR_TTMR_TP.
When the timer triggers, the virtual time delta in nanoseconds between
the time when the timer was set, and when it triggers is calculated.
This nanoseconds value is then divided by TIMER_PERIOD (50) to compute
an increment of cycles to apply to TTCR.
However, this calculation rounds down the number of cycles causing the
undercounting.
A simplistic solution would be to instead round up the number of cycles,
however this will result in the accumulation of timing error over time.
This patch corrects the issue by calculating the time delta in
nanoseconds between when the timer was last reset and the timer event.
This approach allows the TTCR value to be rounded up, but without
accumulating error over time.
Signed-off-by: Joel Holdsworth <jholdsworth@nvidia.com>
[stafford: Incremented version in vmstate_or1k_timer, checkpatch fixes]
Signed-off-by: Stafford Horne <shorne@gmail.com>
We used to only have a single UART on the platform and it was located at
address 0x90000000. When the number of UARTs was increased to 4, the
first UART remained at it's location, but instead of being the first one
to be registered, it became the last.
This caused QEMU to pick 0x90000300 as the default UART, which broke
software that hardcoded the address of 0x90000000 and expected it's
output to be visible when the user configured only a single console.
This caused regressions[1] in the barebox test suite when updating to a
newer QEMU. As there seems to be no good reason to register the UARTs in
inverse order, let's register them by ascending address, so existing
software can remain oblivious to the additional UART ports.
Changing the order of uart registration alone breaks Linux which
was choosing the UART at 0x90000300 as the default for ttyS0. To fix
Linux we fix three things in the device tree:
1. Define stdout-path only one time for the first registered UART
instead of incorrectly defining for each UART.
2. Change the UART alias name from 'uart0' to 'serial0' as almost all
Linux tty drivers look for an alias starting with "serial".
3. Add the UART nodes so they appear in the final DTB in the
order starting with the lowest address and working upwards.
In summary these changes mean that the QEMU default UART (serial_hd(0))
is now setup where:
* serial_hd(0) is the lowest-address UART
* serial_hd(0) is listed first in the DTB
* serial_hd(0) is the /chosen/stdout-path one
* the /aliases/serial0 alias points at serial_hd(0)
[1]: https://lore.barebox.org/barebox/707e7c50-aad1-4459-8796-0cc54bab32e2@pengutronix.de/T/#m5da26e8a799033301489a938b5d5667b81cef6ad
Fixes: 777784bda4 ("hw/openrisc: support 4 serial ports in or1ksim")
Cc: qemu-stable@nongnu.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
[stafford: Change to serial0 alias and update change message, reverse
uart registration order]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
- Prasad's one fix on thread name typo
-----BEGIN PGP SIGNATURE-----
iIgEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZ04mxBIccGV0ZXJ4QHJl
ZGhhdC5jb20ACgkQO1/MzfOr1wbyegEAxWBfoGpPoysYOe+ijwMZKgsXylWzHrfJ
HGlVck7f1RQA/jAwS8aR3t6QZwhL42lXfAlGPX2ebz4IL+f52qs6/nQP
=L+tL
-----END PGP SIGNATURE-----
Merge tag 'migration-20241202-pull-request' of https://gitlab.com/peterx/qemu into staging
Migration pull for 9.2-rc3
- Prasad's one fix on thread name typo
# -----BEGIN PGP SIGNATURE-----
#
# iIgEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZ04mxBIccGV0ZXJ4QHJl
# ZGhhdC5jb20ACgkQO1/MzfOr1wbyegEAxWBfoGpPoysYOe+ijwMZKgsXylWzHrfJ
# HGlVck7f1RQA/jAwS8aR3t6QZwhL42lXfAlGPX2ebz4IL+f52qs6/nQP
# =L+tL
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 02 Dec 2024 21:29:40 GMT
# gpg: using EDDSA key B9184DC20CC457DACF7DD1A93B5FCCCDF3ABD706
# gpg: issuer "peterx@redhat.com"
# gpg: Good signature from "Peter Xu <xzpeter@gmail.com>" [marginal]
# gpg: aka "Peter Xu <peterx@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: B918 4DC2 0CC4 57DA CF7D D1A9 3B5F CCCD F3AB D706
* tag 'migration-20241202-pull-request' of https://gitlab.com/peterx/qemu:
migration: correct multifd receive thread name
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make sure we grab a reference on the subsystem when a VF is realized.
Otherwise, the subsytem will be unrealized automatically when the VFs
are unregistered and unreffed.
This fixes a latent bug but was not exposed until commit 08f6328480
("pcie: Release references of virtual functions"). This was then fixed
(or rather, hidden) by commit c613ad2512 ("pcie_sriov: Do not manually
unrealize"), but that was then reverted (due to other issues) in commit
b0fdaee5d1, exposing the bug yet again.
Cc: qemu-stable@nongnu.org
Fixes: 08f6328480 ("pcie: Release references of virtual functions")
Reviewed-by: Jesper Wendel Devantier <foss@defmacro.it>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The PCI Interrupt Pin Register does not apply to VFs and MUST be
hardwired to zero.
Fixes: 44c2c09488 ("hw/nvme: Add support for SR-IOV")
Reviewed-by: Jesper Wendel Devantier <foss@defmacro.it>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Only call msix_{un,}use_vector() when interrupts are actually enabled
for a completion queue.
Reviewed-by: Jesper Wendel Devantier <foss@defmacro.it>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit fa905f65c5 introduced a machine compatibility parameter to
enable an exclusive bar for msix. It failed to account for this when
cleaning up. Make sure that if an exclusive bar is enabled, we use the
proper cleanup routine.
Cc: qemu-stable@nongnu.org
Fixes: fa905f65c5 ("hw/nvme: add machine compatibility parameter to enable msix exclusive bar")
Reviewed-by: Jesper Wendel Devantier <foss@defmacro.it>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Multifd receive threads run on the destination side.
Correct the thread name marco to indicate the same.
Fixes: e620b1e477 ("migration: Put thread names together with macros")
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20241127111528.167330-1-ppandit@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
