The TMP105 datasheet says that in Interrupt Mode (when TM==1) the device
signals an alert when the temperature equals or exceeds the T_high value and
then remains high until a device register is read or the device responds to
the SMBUS Alert Response address, or the device is put into Shutdown Mode.
Thereafter the Alert pin will only be re-signalled when temperature falls
below T_low; alert can then be cleared in the same set of ways, and the
device returns to its initial "alert when temperature goes above T_high"
mode. (If this textual description is confusing, see figure 3 in the
TI datasheet at https://www.ti.com/lit/gpn/tmp105 .)
We were misimplementing this as a simple "always alert if temperature is
above T_high or below T_low" condition, which gives a spurious alert on
startup if using the "T_high = 80 degrees C, T_low = 75 degrees C" reset
limit values.
Implement the correct (hysteresis) behaviour by tracking whether we
are currently looking for the temperature to rise over T_high or
for it to fall below T_low. Our implementation of the comparator
mode (TM==0) wasn't wrong, but rephrase it to match the way that
interrupt mode is now handled for clarity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-3-peter.maydell@linaro.org
The TMP105 datasheet (https://www.ti.com/lit/gpn/tmp105) says that the
power-up reset values for the T_low and T_high registers are 80 degrees C
and 75 degrees C, which are 0x500 and 0x4B0 hex according to table 5. These
values are then shifted right by four bits to give the register reset
values, since both registers store the 12 bits of temperature data in bits
[15..4] of a 16 bit register.
We were resetting these registers to zero, which is problematic for Linux
guests which enable the alert interrupt and then immediately take an
unexpected overtemperature alert because the current temperature is above
freezing...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-2-peter.maydell@linaro.org
This patch fixes CID 1432800 by removing an unnecessary check.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 5edab03d40 we added tracepoints to the ps2 keyboard
and mouse emulation. However we didn't remove all the debug-by-printf
support. In fact there is only one printf() remaining, and it is
redundant with the trace_ps2_write_mouse() event next to it.
Remove the printf() and the now-unused DEBUG* macros.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20201101133258.4240-1-peter.maydell@linaro.org
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201111073651.72804-1-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The removal of the selection of A15MPCORE from ARM_VIRT also
removed what A15MPCORE selects, ARM_GIC. We still need ARM_GIC.
Fixes: bec3c97e0c ("hw/arm/virt: Remove dependency on Cortex-A15 MPCore peripherals")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201111143440.112763-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the SD spec, to indicate a 2 GiB card, BLOCK_LEN shall be 1024
bytes, hence the READ_BL_LEN field in the CSD register shall be 10
instead of 9.
This fixes the acceptance test error for the NetBSD 9.0 test of the
Orange Pi PC that has an expanded SD card image of 2 GiB size.
Fixes: 6d2d4069c4 ("hw/sd: Correct the maximum size of a Standard Capacity SD Memory Card")
Reported-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-Id: <20201025152357.11865-1-bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The category of the max111x device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201112125824.763182-5-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The category of the nand device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201112125824.763182-4-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The category of the ads7846 device is not set, put it into the 'input'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201112125824.763182-3-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The category of the ssd0323 device is not set, put it into the 'display'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201112125824.763182-2-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Linux has some OS-specific (and sometimes weird) mappings for various SCSI
statuses and sense codes. The most important is probably RESERVATION
CONFLICT. Add them so that they can be reported back to the guest
kernel.
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----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=GI5d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-11-15' into staging
Fix Lesser GPL license versions (should be "2.1" and not "2")
# gpg: Signature made Sun 15 Nov 2020 16:20:10 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-11-15: (26 commits)
nomaintainer: Fix Lesser GPL version number
test: Fix LGPL information in the file headers
tests/acceptance: Fix LGPL information in the file headers
tests/migration: Fix LGPL information in the file headers
sparc tcg cpus: Fix Lesser GPL version number
e1000e: Fix Lesser GPL version number
x86 hvf cpus: Fix Lesser GPL version number
nvdimm: Fix Lesser GPL version number
w32: Fix Lesser GPL version number
tpm: Fix Lesser GPL version number
overall/alpha tcg cpus|hppa: Fix Lesser GPL version number
overall usermode...: Fix Lesser GPL version number
migration: Fix Lesser GPL version number
parallel nor flash: Fix Lesser GPL version number
arm tcg cpus: Fix Lesser GPL version number
x86 tcg cpus: Fix Lesser GPL version number
linux user: Fix Lesser GPL version number
usb: Fix Lesser GPL version number
tricore tcg cpus: Fix Lesser GPL version number
xtensa tcg cpus: Fix Lesser GPL version number
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GCC 9.3.0 thinks that 'method' can be left uninitialized. This code
is already in the "if (bsel || pcihp_bridge_en)" block statement,
but it isn't smart enough to figure it out.
Restrict the code to be used only in the "if (bsel || pcihp_bridge_en)"
block statement to fix (on Ubuntu):
../hw/i386/acpi-build.c: In function 'build_append_pci_bus_devices':
../hw/i386/acpi-build.c:496:9: error: 'method' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
496 | aml_append(parent_scope, method);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: df4008c9c5 ("piix4: don't reserve hw resources when hotplug is off globally")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201108204535.2319870-4-philmd@redhat.com>
Message-Id: <20201110192316.26397-8-alex.bennee@linaro.org>
The v variable goes negative for reg < 0x20. Reorder the code
to first sanity check then calculate v and assign intr to make
sanity checkers happy.
Buglink: https://bugs.launchpad.net/qemu/+bug/1902112
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201105134112.25119-7-kraxel@redhat.com
Add property so scsi command logging can be switched
at runtime instead of compile time.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201105134112.25119-3-kraxel@redhat.com
Replace most DPRINTF macros with trace events.
Drop some DPRINTF macros.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201105134112.25119-2-kraxel@redhat.com
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124134.20083-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123749.19941-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123516.19843-1-chetan4windows@gmail.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123034.19609-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Fixed subject]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122913.19561-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122332.19369-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122157.19321-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023121933.19227-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201019061126.3102-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016145346.27167-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If an interrupt occurs between when we claim and complete an interrupt
we currently drop the interrupt in ibex_plic_irqs_set_pending(). This
somewhat matches hardware that also ignore the interrupt between the
claim and complete process.
In the case of hardware though the physical interrupt line will still
be asserted after we have completed the interrupt. This means we will
still act on the interrupt after the complete process. In QEMU we don't
and instead we drop the interrupt as it is never recorded.
This patch changed the behaviour of the Ibex PLIC so that we save all
interrupts that occur while we are between claiming and completing an
interrupt so that we can act on them after the completition process.
This fixes interrupts being dropped when running Tock on OpenTitain in
QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: e7bcf98c6925b1e6e7828e7c3f85293a09a65b12.1605136387.git.alistair.francis@wdc.com
Storing properties directly in XHCIPciState.xhci doesn't work,
the object_initialize_child() call in xhci_instance_init() will
overwrite them.
This changes the defaults for some properties, which in turn breaks
live migration and possibly other things as well.
So add XHCINecState, store properties there, copy them over on
instance init.
Fixes: 8ddab8dd3d ("usb/hcd-xhci: Split pci wrapper for xhci base model")
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201112103741.2335-1-kraxel@redhat.com
The '%u' conversion specifier is for decimal notation.
When prefixing a format with '0x', we want the hexadecimal
specifier ('%x').
Inspired-by: Dov Murik <dovmurik@linux.vnet.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20201103112558.2554390-3-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit ec87f206d7 ("cirrus: replace debug printf with trace points")
forgot to remove this code once replaced. Do it now.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20201103112558.2554390-2-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since commit 755fba11fb and 8ddab8dd3d we can not build
USB_XHCI_NEC without USB_XHCI_PCI. Correct the Kconfig
dependency.
Fixes: 755fba11fb ("usb/hcd-xhci: Move qemu-xhci device to hcd-xhci-pci.c")
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201109135300.2592982-2-philmd@redhat.com
[ kraxel: restore "default y if PCI_DEVICES" because
"qemu-system-ppc64 -M pseries,usb=on" needs USB_XHCI_NEC=y ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
GCC 9.3.0 thinks that 'method' can be left uninitialized. This code
is already in the "if (bsel || pcihp_bridge_en)" block statement,
but it isn't smart enough to figure it out.
Restrict the code to be used only in the "if (bsel || pcihp_bridge_en)"
block statement to fix (on Ubuntu):
../hw/i386/acpi-build.c: In function 'build_append_pci_bus_devices':
../hw/i386/acpi-build.c:496:9: error: 'method' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
496 | aml_append(parent_scope, method);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: df4008c9c5 ("piix4: don't reserve hw resources when hotplug is off globally")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201107194045.438027-1-philmd@redhat.com>
Acked-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU currently truncates the mmap_offset field when sending
VHOST_USER_ADD_MEM_REG and VHOST_USER_REM_MEM_REG messages. The struct
layout looks like this:
typedef struct VhostUserMemoryRegion {
uint64_t guest_phys_addr;
uint64_t memory_size;
uint64_t userspace_addr;
uint64_t mmap_offset;
} VhostUserMemoryRegion;
typedef struct VhostUserMemRegMsg {
uint32_t padding;
/* WARNING: there is a 32-bit hole here! */
VhostUserMemoryRegion region;
} VhostUserMemRegMsg;
The payload size is calculated as follows when sending the message in
hw/virtio/vhost-user.c:
msg->hdr.size = sizeof(msg->payload.mem_reg.padding) +
sizeof(VhostUserMemoryRegion);
This calculation produces an incorrect result of only 36 bytes.
sizeof(VhostUserMemRegMsg) is actually 40 bytes.
The consequence of this is that the final field, mmap_offset, is
truncated. This breaks x86_64 TCG guests on s390 hosts. Other guest/host
combinations may get lucky if either of the following holds:
1. The guest memory layout does not need mmap_offset != 0.
2. The host is little-endian and mmap_offset <= 0xffffffff so the
truncation has no effect.
Fix this by extending the existing 32-bit padding field to 64-bit. Now
the padding reflects the actual compiler padding. This can be verified
using pahole(1).
Also document the layout properly in the vhost-user specification. The
vhost-user spec did not document the exact layout. It would be
impossible to implement the spec without looking at the QEMU source
code.
Existing vhost-user frontends and device backends continue to work after
this fix has been applied. The only change in the wire protocol is that
QEMU now sets hdr.size to 40 instead of 36. If a vhost-user
implementation has a hardcoded size check for 36 bytes, then it will
fail with new QEMUs. Both QEMU and DPDK/SPDK don't check the exact
payload size, so they continue to work.
Fixes: f1aeb14b08 ("Transmit vhost-user memory regions individually")
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20201109174355.1069147-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: f1aeb14b08 ("Transmit vhost-user memory regions individually")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
There is a field with vmstate_ghes_state as vmsd in vmstate_ghes_state,
which will lead to infinite recursion in dump_vmstate_vmsd.
Fixes: a08a64627b ("ACPI: Record the Generic Error Status Block address")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201112020638.874515-1-liangpeng10@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit 348b8d1a76 "macio: don't reference serial_hd() directly within the device"
removed the setting of user_creatable to false on the basis that the restriction
was due to the use of serial_hd() in macio_instance_init().
Unfortunately this isn't the full story since the PIC object property links
must still be set before the device is realized. Whilst it is possible to update
the macio device and Mac machines to resolve this, the fix is too invasive at
this point in the release cycle.
For now simply set user_creatable back to false in macio_class_init() to
prevent QEMU from segfaulting in anticipation of the proper fix arriving in
QEMU 6.0.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201110103111.18395-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of casting an address within a uint8_t array to a
uint32_t*, use stl_le_p(). This handles possibly misaligned
addresses which would otherwise crash on some hosts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The ctucan driver defines types for its registers which are a union
of a uint32_t with a struct with bitfields for the individual
fields within that register. This is a bad idea, because bitfields
aren't portable. The ctu_can_fd_regs.h header works around the
most glaring of the portability issues by defining the
fields in two different orders depending on the setting of the
__LITTLE_ENDIAN_BITFIELD define. However, in ctucan_core.h this
is unconditionally set to 1, which is wrong for big-endian hosts.
Set it only if HOST_WORDS_BIGENDIAN is not set. There is no need
for a "have we defined it already" guard, because the only place
that should set it is ctucan_core.h, which has the usual
double-inclusion guard.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Coverity points out that in ctucan_send_ready_buffers() we
set buff_st_mask = 0xf << (i * 4) inside the loop, but then
we never use it before overwriting it later.
The only thing we use the mask for is as part of the code that is
inserting the new buff_st field into tx_status. That is more
comprehensibly written using deposit32(), so do that and drop the
mask variable entirely.
We also update the buff_st local variable at multiple points
during this function, but nothing can ever see these
intermediate values, so just drop those, write the final
TXT_TOK as a fixed constant value, and collapse the only
remaining set/use of buff_st down into an extract32().
Fixes: Coverity CID 1432869
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
