v8.1M introduces a new TRD flag in the CCR register, which enables
checking for stack frame integrity signatures on SG instructions.
This bit is not banked, and is always RAZ/WI to Non-secure code.
Adjust the code for handling CCR reads and writes to handle this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-23-peter.maydell@linaro.org
In v8.1M a REVIDR register is defined, which is at address 0xe00ecfc
and is a read-only IMPDEF register providing implementation specific
minor revision information, like the v8A REVIDR_EL1. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-19-peter.maydell@linaro.org
The FPDSCR register has a similar layout to the FPSCR. In v8.1M it
gains new fields FZ16 (if half-precision floating point is supported)
and LTPSIZE (always reads as 4). Update the reset value and the code
that handles writes to this register accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-16-peter.maydell@linaro.org
For M-profile CPUs, the range from 0xe0000000 to 0xe00fffff is the
Private Peripheral Bus range, which includes all of the memory mapped
devices and registers that are part of the CPU itself, including the
NVIC, systick timer, and debug and trace components like the Data
Watchpoint and Trace unit (DWT). Within this large region, the range
0xe000e000 to 0xe000efff is the System Control Space (NVIC, system
registers, systick) and 0xe002e000 to 0exe002efff is its Non-secure
alias.
The architecture is clear that within the SCS unimplemented registers
should be RES0 for privileged accesses and generate BusFault for
unprivileged accesses, and we currently implement this.
It is less clear about how to handle accesses to unimplemented
regions of the wider PPB. Unprivileged accesses should definitely
cause BusFaults (R_DQQS), but the behaviour of privileged accesses is
not given as a general rule. However, the register definitions of
individual registers for components like the DWT all state that they
are RES0 if the relevant component is not implemented, so the
simplest way to provide that is to provide RAZ/WI for the whole range
for privileged accesses. (The v7M Arm ARM does say that reserved
registers should be UNK/SBZP.)
Expand the container MemoryRegion that the NVIC exposes so that
it covers the whole PPB space. This means:
* moving the address that the ARMV7M device maps it to down by
0xe000 bytes
* moving the off and the offsets within the container of all the
subregions forward by 0xe000 bytes
* adding a new default MemoryRegion that covers the whole container
at a lower priority than anything else and which provides the
RAZWI/BusFault behaviour
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-2-peter.maydell@linaro.org
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-5-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-4-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-3-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-2-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Trusted Firmware now supports A72 on sbsa-ref by default [1] so enable
it for QEMU as well. A53 was already enabled there.
1. https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7117
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201120141705.246690-1-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect CAN0 and CAN1 on the ZynqMP.
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-3-git-send-email-fnu.vikram@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx ZynqMP CAN controller is developed based on SocketCAN, QEMU CAN bus
implementation. Bus connection and socketCAN connection for each CAN module
can be set through command lines.
Example for using single CAN:
-object can-bus,id=canbus0 \
-machine xlnx-zcu102.canbus0=canbus0 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0
Example for connecting both CAN to same virtual CAN on host machine:
-object can-bus,id=canbus0 -object can-bus,id=canbus1 \
-machine xlnx-zcu102.canbus0=canbus0 \
-machine xlnx-zcu102.canbus1=canbus1 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0 \
-object can-host-socketcan,id=socketcan1,if=vcan0,canbus=canbus1
To create virtual CAN on the host machine, please check the QEMU CAN docs:
https://github.com/qemu/qemu/blob/master/docs/can.txt
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-2-git-send-email-fnu.vikram@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Accroding to the SMMUv3 spec, the SPAN field of Level1 Stream Table
Descriptor is 5 bits([4:0]).
Fixes: 9bde7f0674f(hw/arm/smmuv3: Implement translate callback)
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Message-id: 20201124023711.1184-1-jiangkunkun@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an eeprom device and fill it with fru
information
$ ipmitool fru print 0
Product Manufacturer : Bytedance
Product Name : G220A
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201210103607.556-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The controller can be configured to disable or enable address and data
byte lanes when issuing commands. This is useful in read command mode
to send SPI NOR commands that don't have an address space, such as
RDID. It's a good way to have a unified read operation for registers
and flash contents accesses.
A new SPI driver proposed by Aspeed makes use of this feature. Add
support for address lanes to start with. We will do the same for the
data lanes if they are controlled one day.
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20201120161547.740806-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On the AST2600A1, the SRAM size was increased to 89KB.
Fixes: 7582591ae7 ("aspeed: Support AST2600A1 silicon revision")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201112012113.835858-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
G220A is a 2 socket x86 motherboard supported by OpenBMC.
Strapping configuration was obtained from hardware.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20201122105134.671-2-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Create second ioapic, route virtio-mmio IRQs to it,
allow more virtio-mmio devices (24 instead of 8).
Needs ACPI, enabled by default, can be turned off
using -machine ioapic2=off
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-8-kraxel@redhat.com
With the improved gsi_handler() we don't need
our private version any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-7-kraxel@redhat.com
Allows to move them in case we have enough
irq lines available.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-6-kraxel@redhat.com
This will allow to increase the number of transports in
case we have enough irq lines available for them all.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-5-kraxel@redhat.com
Add ioapic_init_secondary to initialize it, wire up
in gsi handling and acpi apic table creation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-4-kraxel@redhat.com
Rewrite function to use switch() for IRQ number mapping.
Check i8259_irq exists before raising it so the function
also works in case no i8259 (aka pic) is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20201203105423.10431-3-kraxel@redhat.com
Added AER capability for virtio-pci devices.
Also added property for devices, by default AER is disabled.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20201203110713.204938-3-andrew@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Removed hardcoded offset for ats. Added cap offset counter
for future capabilities like AER.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20201203110713.204938-2-andrew@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Keep CPU hotunplug with SMI disabled on 5.2 and older and enable
it by default on newer machine types.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be reused by next patch to check validity of unplug
feature.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
if firmware and QEMU negotiated CPU hotunplug support, generate
_EJ0 method so that it will mark CPU for removal by firmware and
pass control to it by triggering SMI.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adds bit #4 to status/control field of CPU hotplug MMIO interface.
New bit will be used OSPM to mark CPUs as pending for removal by firmware,
when it calls _EJ0 method on CPU device node. Later on, when firmware
sees this bit set, it will perform CPU eject which will clear bit #4
as well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At Hewlett Packard Inc. we have a need for increased fw size to enable testing of our custom fw.
Rebase v6 patch to d73c46e4
Signed-off-by: Erich McMillan <erich.mcmillan@hp.com>
Message-Id: <20201208155338.14-1-erich.mcmillan@hp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity points out that the realize function for the TYPE_MCF5206_MBAR
device leaks the IRQ array it allocates with qemu_allocate_irqs().
Keep a pointer to it in the device state struct to avoid the leak.
(Since it needs to stay around for the life of the simulation there
is no need to actually free it, and the leak was harmless.)
Fixes: Coverity CID 1432412
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201120172314.14725-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only three uses remained, and we can remove them on that case.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-28-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate device just once.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-27-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pass it as an argument.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-26-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-25-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So we can calculate the device id when we need it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-24-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It can never give one error.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-23-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We check that it exist at device creation time, so we don't have to
check anywhere else.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-22-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit:
* Rename them to failover_find_primary_devices() so
- it starts with failover_
- it don't connect anything, just find the primary device
* Create documentation for the function
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-19-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It just calls virtio_net_find_primary(), so just update the callers.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-18-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use pasive.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-17-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We didn't use at all the -1 value, and we don't really care. It was
only used for the cases when this is not the device that we are
searching for. And in that case we should not hide the device.
Once there, simplify virtio-Snet_primary_should_be_hidden.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-16-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
a - is_my_primary() never sets one error
b - If we return 1, primary_device_id is always set
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-15-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Two things, at this point:
* n->primary_device_id has to be set, otherwise
virtio_net_find_primary don't work. So we have a leak here.
* it has to be exactly the same that prim_dev->id because what
qdev_find_recursive() does is just compare this two values.
So remove the unneeded assignment and leaky bits.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-14-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only used once. And we have there opts->id, so no need for it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-13-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate it, and we only use it once anyways.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-12-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was really only used once, in failover_add_primary(). Just search
for it on global opts when it is needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-11-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
