Add a basic board with interrupt controller (intc), timer, serial
(uartlite), small memory called LMB@0 (128kB) and DDR@0x80000000
(configured via command line eg. -m 2g).
This is basic configuration which matches HW generated out of AMD Vivado
(design tools). But initial configuration is going beyond what it is
configured by default because validation should be done on other
configurations too. That's why wire also additional uart16500, axi
ethernet(with axi dma).
GPIOs, i2c and qspi is also listed for completeness.
IRQ map is: (addr)
0 - timer (0x41c00000)
1 - uartlite (0x40600000)
2 - i2c (0x40800000)
3 - qspi (0x44a00000)
4 - uart16550 (0x44a10000)
5 - emaclite (0x40e00000)
6 - timer2 (0x41c10000)
7 - axi emac (0x40c00000)
8 - axi dma (0x41e00000)
9 - axi dma
10 - gpio (0x40000000)
11 - gpio2 (0x40010000)
12 - gpio3 (0x40020000)
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241125134739.18189-1-sai.pavan.boddu@amd.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This device models the RISC-V IOMMU as a sysbus device. The same design
decisions taken in the riscv-iommu-pci device were kept, namely the
existence of 4 vectors are available for each interrupt cause.
The WSIs are emitted using the input of the s->notify() callback as a
index to an IRQ list. The IRQ list starts at 'base_irq' and goes until
base_irq + 3. This means that boards must have 4 contiguous IRQ lines
available, starting from 'base_irq'.
Signed-off-by: Tomasz Jeznach <tjeznach@rivosinc.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241106133407.604587-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V IOMMU can be modelled as a PCIe device following the
guidelines of the RISC-V IOMMU spec, chapter 7.1, "Integrating an IOMMU
as a PCIe device".
Signed-off-by: Tomasz Jeznach <tjeznach@rivosinc.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241016204038.649340-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V IOMMU specification is now ratified as-per the RISC-V
international process. The latest frozen specifcation can be found at:
https://github.com/riscv-non-isa/riscv-iommu/releases/download/v1.0/riscv-iommu.pdf
Add the foundation of the device emulation for RISC-V IOMMU. It includes
support for s-stage (sv32, sv39, sv48, sv57 caps) and g-stage (sv32x4,
sv39x4, sv48x4, sv57x4 caps).
Other capabilities like ATS and DBG support will be added incrementally
in the next patches.
Co-developed-by: Sebastien Boeuf <seb@rivosinc.com>
Signed-off-by: Sebastien Boeuf <seb@rivosinc.com>
Signed-off-by: Tomasz Jeznach <tjeznach@rivosinc.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Jason Chien <jason.chien@sifive.com>
Message-ID: <20241016204038.649340-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Avoid having to list dependencies such as libfdt twice, both on common_ss
and specific_ss. Instead, just take all the dependencies in common_ss
and allow the target-specific libqemu-*.fa library to use them.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add basic ACPI infrastructure for RISC-V with below tables.
1) DSDT with below basic objects
- CPUs
- fw_cfg
2) FADT revision 6 with HW_REDUCED flag
3) XSDT
4) RSDP
Add this functionality in a new file virt-acpi-build.c and enable
building this infrastructure.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230302091212.999767-5-sunilvl@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Only the Virt and Spike machines use NUMA. Add a RISCV_NUMA Kconfig
symbol and only have these machines select it. Adapt the Meson file
to only built it if required.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-8-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Every RISC-V machine needs riscv_hart hence there is no need to
have a dedicated Kconfig option for it. Drop the Kconfig option
and always build riscv_hart.c.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an initial support for Microchip PolarFire SoC Icicle Kit.
The Icicle Kit board integrates a PolarFire SoC, with one SiFive's
E51 plus four U54 cores and many on-chip peripherals and an FPGA.
For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga
Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000.
The following perepherals are created as an unimplemented device:
- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
More devices will be added later.
The BIOS image used by this machine is hss.bin, aka Hart Software
Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services
To launch this machine:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit
The memory is set to 1 GiB by default to match the hardware.
A sanity check on ram size is performed in the machine init routine
to prompt user to increase the RAM size to > 1 GiB when less than
1 GiB ram is detected.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
All Meson executables should specify their dependencies explicitly, either
directly or indirectly via declare_dependency. Makefiles instead did
not propagate dependencies correctly from static libraries, for example.
Therefore, flags for dependencies need not be included in QEMU_CFLAGS.
LIBS is not used at all, so drop that one as well.
In a few cases the dependencies were not yet specified, so add them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We add common helper routines which can be shared by RISC-V
multi-socket NUMA machines.
We have two types of helpers:
1. riscv_socket_xyz() - These helper assist managing multiple
sockets irrespective whether QEMU NUMA is enabled/disabled
2. riscv_numa_xyz() - These helpers assist in providing
necessary QEMU machine callbacks for QEMU NUMA emulation
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-4-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Each architecture's sourceset is placed in an hw_arch dictionary, and picked up
from there when building the per-emulator static_library.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
