So that we've a place to migrate it to / from to allow restoring it after
migration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
After a live migration, the usb-hcd will re-queue all packets by
walking over the schedule in the guest memory again, but requests which
were encountered on the migration source before will already be in flight,
so these should *not* be re-send to the usbredir-host.
This patch adds an already in flight packet ud queue, which will be filled by
the source before migration and then moved over to the migration dest, any
async handled packets are then checked against this queue to avoid sending
the same packet to the usbredir-host twice.
Signed-off-by: Hans de Goede <hdegoede@redhat,com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When removing unseen queue-heads from the async queue list, we should not
set the seen flag to 0, as this may cause them to be removed by
ehci_queues_rip_unused() during the next call to ehci_advance_async_state()
if the timer is late or running at a low frequency.
Note:
1) This *may* have caused the instant unlink / relinks described in commit
9bc3a3a216
2) Rather then putting more if-s inside ehci_queues_rip_unused, this patch
instead introduces a new ehci_queues_rip_unseen function.
3) This patch also makes it save to call ehci_queues_rip_unseen() multiple
times, which gets used in the folluw up patch titled:
"ehci: Walk async schedule before and after migration"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Until now we used only the agent to change the monitor count and each
monitor resolution. This patch introduces the qemu part of using the
device as the mediator instead of the agent via virtio-serial.
Spice (>=0.11.5) calls the new QXLInterface::client_monitors_config,
which returns wether the interrupt is enabled, and if so and given a non
NULL monitors config will
generate an interrupt QXL_INTERRUPT_CLIENT_MONITORS_CONFIG with crc
checksum for the guest to verify a second call hasn't interfered.
The maximal number of monitors is limited on the QXLRom to 64.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add two new trace events:
qxl_send_events(int qid, uint32_t events) "%d %d"
qxl_set_guest_bug(int qid) "%d"
Change qxl_io_unexpected_vga_mode parameters to be equivalent to those
of qxl_io_write for easier grouping under a single systemtap probe.
Change d to qxl in one place.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
While testing q35, I found that windows 7 (specifically, windows 7 ultimate
with sp1 x64), wouldn't install because it can't find the cdrom or disk drive.
The failure message is: 'A required cd/dvd device driver is missing. If you
have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now.'
This can also be reproduced on piix by adding an ahci controller, and
observing that windows 7 does not see any devices behind it.
The problem is that when windows issues a HBA reset, qemu does not reset the
individual ports' PxCMD register. Windows 7 then reads back the PxCMD register
and presumably assumes that the ahci controller has already been initialized.
Windows then never sets up the PxIE register to enable interrupts, and thus it
never gets irqs back when it sends ata device inquiry commands.
This change brings qemu into ahci 1.3 specification compliance.
Section 10.4.3 HBA Reset:
"
When GHC.HR is set to '1', GHC.AE, GHC.IE, the IS register, and all port
register fields (except PxFB/PxFBU/PxCLB/PxCLBU) that are not HwInit in the
HBA's register memory space are reset.
"
I've also re-tested Fedora 16 and 17 to verify that they continue to work with
this change.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Report from smatch:
hw/ide/core.c:1472 ide_exec_cmd(423) error: buffer overflow 'smart_attributes' 8 <= 29
hw/ide/core.c:1474 ide_exec_cmd(425) error: buffer overflow 'smart_attributes' 8 <= 29
hw/ide/core.c:1475 ide_exec_cmd(426) error: buffer overflow 'smart_attributes' 8 <= 29
...
The upper limit of 30 was never reached because both for loops terminated
when 'smart_attributes' reached end of list, so there was no real buffer
overflow.
Nevertheless, changing the code not only fixes the error report, but also
reduces the size of smart_attributes and simplifies the for loops.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The START STOP UNIT command will only eject/load media if
power condition is zero.
If power condition is !0 then LOEJ and START will be ignored.
From MMC (sbc contains similar wordings too)
The Power Conditions field requests the block device to be placed
in the power condition defined in
Table 558. If this field has a value other than 0h then the Start
and LoEj bits shall be ignored.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The Linux ehci isoc scheduling code fills the entire schedule ahead of
time minus 80 frames. If we make a large jump in where we are in the
schedule, ie 40 frames, then the scheduler all of a sudden will only have
40 frames left to work in, causing it to fail packet submissions
with error -27 (-EFBIG).
Changes in v2:
-Don't hardcode a maximum number of frames to process in one tick, instead:
-Process a minimum number of frames to ensure we do eventually catch up
-Stop (after the minimum number) when the guest has requested an irq
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If Interrupt Threshold Control is 8 or a multiple of 8, then
s->usbsts_frindex can become exactly 0x4000, at which point
(s->usbsts_frindex > s->frindex) will never become true, as
s->usbsts_frindex will not be lowered / reset in this case.
This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Also register different memory regions for capabilities,
operational registers and port status registers. Create
separate tracepoints for operational regs and port status
regs. Ditch a bunch of sanity checks because the memory
core will do this for us now.
Offloading the byte, word and dword access handling to the
memory core also has the side effect of fixing ehci register
access on bigendian hosts.
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add back a call to qxl_spice_destroy_surface_wait_complete() in qxl_spice_destroy_surface_wait(),
that was removed by commit c480bb7da4
It is needed to complete surface-removal cleanup, for non async.
For async, qxl_spice_destroy_surface_wait_complete is called upon operation completion.
Signed-off-by: Uri Lublin <uril@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xhci needs this for USB_REQ_SET_ADDRESS due to the way
usb addressing is handled by the xhci hardware.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The recent introduction of set_client_capabilities has broken
(seamless) migration by trying to call qxl_send_events pre (seamless
incoming) and post (*) migration, triggering the following assert:
qxl_send_events: Assertion `qemu_spice_display_is_running(&d->ssd)' failed.
The solution is easy, pre migration the guest will have already received
the client caps on the migration source side, and post migration there no
longer is a guest, so we can simply ignore the set_client_capabilities call
in both those scenarios.
*) Post migration, so not fatal for to the migration itself, but still a crash
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In preparation of stopping to flush coalesced MMIO unconditionally on
vmexits, mark VGA MMIO and PIO regions as synchronous /wrt coalesced
MMIO and flush the buffer explicitly on PIO accesses that do not use
generic memory regions yet.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
... and register subregions instead, so we offload the dispatching
to the the memory subsystem which is designed to handle it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move all state belonging to the (single) interrupter into a separate
struct. First step in adding support for multiple interrupters.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Split xhci_irq_update into a function which handles intx updates
(including lowering the irq line once the guests acks the interrupt)
and one which is used for raising an irq only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Drop custom write_config function which isn't needed any more.
Make the msi property a bit property so it accepts 'on' & 'off'.
Enable MSI by default.
TODO: add compat property to disable on old machine types.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add support for building superspeed endpoint companion descriptors,
create them for superspeed usb devices.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch changes the way xhci ports are linked to USBPorts. The fixed
1:1 relationship between xhci ports and USBPorts is gone. Now each
USBPort represents a physical plug which has usually two xhci ports
assigned: one usb2 and ond usb3 port. usb devices show up at one or the
other, depending on whenever they support superspeed or not.
This patch also makes the number of usb2 and usb3 ports runtime
configurable by adding 'p2' and 'p3' properties. It is allowed to
have different numbers of usb2 and usb3 ports. Specifying p2=4,p3=2
will give you an xhci adapter which supports all speeds on physical
ports 1+2 and usb2 only on ports 3+4.
Change the register layout to be a bit more sparse and also not depend
on the number of ports. Useful when for making the number of ports
runtime-configurable.
This patch splits the xhci_xfer_data function into three.
The xhci_xfer_data function used to do does two things:
(1) copy transfer data between guest memory and a temporary buffer.
(2) report transfer results to the guest using events.
Now we three functions to handle this:
(1) xhci_xfer_map creates a scatter list for the transfer and
uses that (instead of the temporary buffer) to build a
USBPacket.
(2) xhci_xfer_unmap undoes the mapping.
(3) xhci_xfer_report sends out events.
The patch also fixes reporting of transaction errors which must be
reported unconditinally, not only in case the guest asks for it
using the ISP flag.
[ v2: fix warning ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
original xhci code (the one which used libusb directly) used to use
'background transfers' for iso streams. In upstream qemu the iso
stream buffering is handled by usb-host & usb-redir, so we will
never ever need this. It has been left in as reference, but is dead
code anyway. Rip it out.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Windows users need to know that they have to use the Baum driver to make
the qemu braille device work.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In order for redirection to work properly when redirecting to an emulated
XHCI controller, the usb-redir-host must support both
usb_redir_cap_ep_info_max_packet_size and usb_redir_cap_64bits_ids,
reject any devices redirected to an XHCI controller when these are not
supported.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
