Migration relies on having the same device configuration on the source
and destination. Therefore, there is no need to modify flags,
timer capabilities and the fw_cfg HPET block id on migration;
it was set to exactly the same values by realize.
Reviewed-by: Zhao Liu <zhao1.liu@intel.com> (hpet_post_load only)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These devices are only used by the ARM targets, which are
only built as little-endian. Therefore the DEVICE_NATIVE_ENDIAN
definition expand to DEVICE_LITTLE_ENDIAN (besides, the
DEVICE_BIG_ENDIAN case isn't tested). Simplify directly using
DEVICE_LITTLE_ENDIAN.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20250212113938.38692-2-philmd@linaro.org>
Replace the DEVICE_NATIVE_ENDIAN MemoryRegionOps by a pair of
DEVICE_LITTLE_ENDIAN / DEVICE_BIG_ENDIAN.
Add the "endianness" property to select the device endianness.
This property is unspecified by default, and machines need to
set it explicitly.
Set the proper endianness for each machine using the device.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20250213122217.62654-5-philmd@linaro.org>
HPET device needs to access and update hpet_cfg variable, but now it is
defined in hw/i386/fw_cfg.c and Rust code can't access it.
Move hpet_cfg definition to hpet.c (and rename it to hpet_fw_cfg). This
allows Rust HPET device implements its own global hpet_fw_cfg variable,
and will further reduce the use of unsafe C code access and calls in the
Rust HPET implementation.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Link: https://lore.kernel.org/r/20250210030051.2562726-2-zhao1.liu@intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The timer controller include 8 sets of 32-bit decrement counters, based on
either PCLK or 1MHZ clock and the design of timer controller between AST2600
and AST2700 are almost the same.
TIMER0 – TIMER7 has their own individual control and interrupt status register.
In other words, users are able to set timer control in register TMC10 with
different TIMER base address and clear timer control and interrupt status in
register TMC14 with different TIMER base address.
Introduce new "aspeed_2700_timer_read" and "aspeed_2700_timer_write" callback
functions and a new ast2700 class to support AST2700.
The base address of TIMER0 to TIMER7 as following.
Base Address of Timer 0 = 0x12C1_0000
Base Address of Timer 1 = 0x12C1_0040
Base Address of Timer 2 = 0x12C1_0080
Base Address of Timer 3 = 0x12C1_00C0
Base Address of Timer 4 = 0x12C1_0100
Base Address of Timer 5 = 0x12C1_0140
Base Address of Timer 6 = 0x12C1_0180
Base Address of Timer 7 = 0x12C1_01C0
The register address space of each TIMER is "0x40" , and uses the following
formula to get the index and register of each TIMER.
timer_index = offset >> 6;
timer_offset = offset & 0x3f;
The TMC010 is a counter control set and interrupt status register. Write "1" to
TMC10[3:0] will set the specific bits to "1". Introduce a new
"aspeed_2700_timer_set_ctrl" function to handle this register behavior.
The TMC014 is a counter control clear and interrupt status register, to clear
the specific bits to "0", it should write "1" to TMC14[3:0] on the same bit
position. Introduce a new "aspeed_2700_timer_clear_ctrl" function to handle
this register behavior. TMC014 does not support read operation.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20250113064455.1660564-3-jamin_lin@aspeedtech.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The register set have a significant change in AST2700. The TMC00-TMC3C
are used for TIMER0 and TMC40-TMC7C are used for TIMER1. In additional,
TMC20-TMC3C and TMC60-TMC7C are reserved registers for TIMER0 and TIMER1,
respectively.
Besides, each TIMER has their own control and interrupt status register.
In other words, users are able to set control and interrupt status for TIMER0
in one register. Both aspeed_timer_read and aspeed_timer_write callback
functions are not compatible AST2700.
Introduce common read and write functions for ASPEED timers.
Modify the aspeed_timer_read and aspeed_timer_write functions to delegate to
SoC-specific callbacks first.
Update the AST2400, AST2500, AST2600 and AST1030 specific read and write
functions to call the common implementations for common register accesses.
This refactoring improves the organization of call delegation and prepares the
codebase for future SoC-specific specializations, such as the AST2700.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20250113064455.1660564-2-jamin_lin@aspeedtech.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250108092538.11474-11-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
All these MemoryRegionOps read() and write() handlers are
implemented expecting 32-bit accesses. Clarify that setting
.impl.min/max_access_size fields.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20241105130431.22564-8-philmd@linaro.org>
HPETState.capability stores the emulated value for "general capabilities
and id register" instead of "main counter register".
Fix the comment to accurately reflect this.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Headers in include/sysemu/ are not only related to system
*emulation*, they are also used by virtualization. Rename
as system/ which is clearer.
Files renamed manually then mechanical change using sed tool.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Lei Yang <leiyang@redhat.com>
Message-Id: <20241203172445.28576-1-philmd@linaro.org>
Now that all of the Property arrays are counted, we can remove
the terminator object from each array. Update the assertions
in device_class_set_props to match.
With struct Property being 88 bytes, this was a rather large
form of terminator. Saves 30k from qemu-system-aarch64.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Lei Yang <leiyang@redhat.com>
Link: https://lore.kernel.org/r/20241218134251.4724-21-richard.henderson@linaro.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The product "icnto * s->tcntb" may overflow uint32_t.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Frolov <frolov@swemel.ru>
Message-id: 20241106083801.219578-2-frolov@swemel.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-id: 20241103143330.123596-3-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the datasheet of AST2600 description, interrupt status set by HW
and clear to "0" by software writing "1" on the specific bit.
Therefore, if firmware set the specific bit "1" in the interrupt status
register(0x34), the specific bit of "s->irq_sts" should be cleared 0.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Fixes: fadefada4d ("aspeed/timer: Add support for IRQ status register on the AST2600")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Remove the omap_synctimer device, which is only in the OMAP2 SoC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240903160751.4100218-46-peter.maydell@linaro.org
The omap_gptimer device is only in the OMAP2 SoC, which we
are removing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240903160751.4100218-45-peter.maydell@linaro.org
The pxa27x-timer can be removed now we have removed the PXA2xx
SoC models. The pxa25x-timer device must remain as it is still
used by strongarm.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240903160751.4100218-24-peter.maydell@linaro.org
pxa2xx_timer includes pxa.h, but it doesn't actually make
use of any of the #defines, function prototypes or structs
defined there. Remove the unnecessary include (we will
shortly be removing the whole header file).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240903160751.4100218-15-peter.maydell@linaro.org
Currently the STRONGARM KConfig symbol pulls in PXA2XX. Since we've now
removed all the true uses of PXA2XX, we'd like to remove the PXA2XX
symbol too. To permit that, make STRONGARM directly select the things
it truly depends on:
* pxa25x-timer
* SSI
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240903160751.4100218-14-peter.maydell@linaro.org
We just removed the single machine using it (axis-dev88).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-12-philmd@linaro.org>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
If the period is set to a value that is too low, there could be no
time left to run the rest of QEMU. Do not trigger interrupts faster
than 1 MHz.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the full 64-bit value at which the timer should fire.
This makes it possible to skip the imprecise hpet_calculate_diff()
step, and to remove the clamping of the period to 31 or 63 bits.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Declare the MemoryRegionOps so that 64-bit reads and writes to the HPET
are received directly. This makes it possible to unify the code to
process low and high parts: for 32-bit reads, extract the desired word;
for 32-bit writes, just merge the desired part into the old value and
proceed as with a 64-bit write.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The variable "val" is used for two different purposes. As an intermediate
value when writing configuration registers, and to store the cleared bits
when writing ISR.
Use "new_val" for the former, and rename the variable so that it is clearer
for the latter case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several bugs in the handling of the ISR register:
- switching level->edge was not lowering the interrupt and
clearing ISR
- switching on the enable bit was not raising a level-triggered
interrupt if the timer had fired
- the timer must be kept running even if not enabled, in
order to set the ISR flag, so writes to HPET_TN_CFG must
not call hpet_del_timer()
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 3787324101 ("hpet: Fix emulation of HPET_TN_SETVAL (Jan Kiszka)",
2009-04-17) applied the fix only to the low 32-bits of the comparator, but
it should be done for the high bits as well. Otherwise, the high 32-bits
of the comparator cannot be written and they remain fixed to 0xffffffff.
Co-developed-by: TaiseiIto <taisei1212@outlook.jp>
Signed-off-by: TaiseiIto <taisei1212@outlook.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When writing a new period, the clamping should use a maximum value
rather tyhan a bit mask. Also, when writing the high bits new_val
is shifted right by 32, so the maximum allowed period should also
be shifted right.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit updates the a9_gtimer_get_current_cpu() function to handle
cases where QTest is enabled. When QTest is used, it returns 0 instead
of dereferencing the current_cpu, which can be NULL. This prevents the
program from crashing during QTest runs.
Reproducer:
cat << EOF | qemu-system-aarch64 -display \
none -machine accel=qtest, -m 512M -machine npcm750-evb -qtest stdio
writel 0xf03fe20c 0x26d7468c
EOF
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240618144009.3137806-1-zheyuma97@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.
Commit created with
for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done
and no manual edits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org
The ALTERA_TIMER was only used by Nios II machines,
which have been removed. Since it has no direct user,
remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240327144806.11319-4-philmd@linaro.org>
A few watchdog devices use qemu_system_reset_request(). This is not ideal since
behaviour of watchdog-expiry can't be changed by QMP using `watchdog_action`.
As stated in BiteSizedTasks wiki page, instead of using qemu_system_reset_request()
to reset when a watchdog timer expires, let watchdog_perform_action() decide
what to do.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2124
Signed-off-by: Abhiram Tilak <atp.exp@gmail.com>
Message-id: 20240216192612.30838-5-atp.exp@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HPET_INTCAP is specific to TYPE_HPET, so define it there.
hpet.c doesn't need to include "hw/i386/pc.h" anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Split out the headers for each peripherals and move them in their
right hardware directory.
Update Copyright and add SPDX-License-Identifier at the same time.
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-2-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This conversion is pretty straight-forward. Standardized some formatting
so the +0 and +4 offset cases can recycle the same message.
Signed-off-by: Daniel Hoffman <dhoff749@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231118231129.2840388-1-dhoff749@gmail.com>
[PMD: Fixed few string formats]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This are the easiest cases, where we were already using
VMSTATE_INSTANCE_ID_ANY.
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231020090731.28701-3-quintela@redhat.com>
infrastructure for vhost-vdpa shadow work
piix south bridge rework
reconnect for vhost-user-scsi
dummy ACPI QTG DSM for cxl
tests, cleanups, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmU06PMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpNIsH/0DlKti86VZLJ6PbNqsnKxoK2gg05TbEhPZU
pQ+RPDaCHpFBsLC5qsoMJwvaEQFe0e49ZFemw7bXRzBxgmbbNnZ9ArCIPqT+rvQd
7UBmyC+kacVyybZatq69aK2BHKFtiIRlT78d9Izgtjmp8V7oyKoz14Esh8wkE+FT
ypHUa70Addi6alNm6BVkm7bxZxi0Wrmf3THqF8ViYvufzHKl7JR5e17fKWEG0BqV
9W7AeHMnzJ7jkTvBGUw7g5EbzFn7hPLTbO4G/VW97k0puS4WRX5aIMkVhUazsRIa
zDOuXCCskUWuRapiCwY0E4g7cCaT8/JR6JjjBaTgkjJgvo5Y8Eg=
=ILek
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups
infrastructure for vhost-vdpa shadow work
piix south bridge rework
reconnect for vhost-user-scsi
dummy ACPI QTG DSM for cxl
tests, cleanups, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmU06PMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpNIsH/0DlKti86VZLJ6PbNqsnKxoK2gg05TbEhPZU
# pQ+RPDaCHpFBsLC5qsoMJwvaEQFe0e49ZFemw7bXRzBxgmbbNnZ9ArCIPqT+rvQd
# 7UBmyC+kacVyybZatq69aK2BHKFtiIRlT78d9Izgtjmp8V7oyKoz14Esh8wkE+FT
# ypHUa70Addi6alNm6BVkm7bxZxi0Wrmf3THqF8ViYvufzHKl7JR5e17fKWEG0BqV
# 9W7AeHMnzJ7jkTvBGUw7g5EbzFn7hPLTbO4G/VW97k0puS4WRX5aIMkVhUazsRIa
# zDOuXCCskUWuRapiCwY0E4g7cCaT8/JR6JjjBaTgkjJgvo5Y8Eg=
# =ILek
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 22 Oct 2023 02:18:43 PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (62 commits)
intel-iommu: Report interrupt remapping faults, fix return value
MAINTAINERS: Add include/hw/intc/i8259.h to the PC chip section
vhost-user: Fix protocol feature bit conflict
tests/acpi: Update DSDT.cxl with QTG DSM
hw/cxl: Add QTG _DSM support for ACPI0017 device
tests/acpi: Allow update of DSDT.cxl
hw/i386/cxl: ensure maxram is greater than ram size for calculating cxl range
vhost-user: fix lost reconnect
vhost-user-scsi: start vhost when guest kicks
vhost-user-scsi: support reconnect to backend
vhost: move and rename the conn retry times
vhost-user-common: send get_inflight_fd once
hw/i386/pc_piix: Make PIIX4 south bridge usable in PC machine
hw/isa/piix: Implement multi-process QEMU support also for PIIX4
hw/isa/piix: Resolve duplicate code regarding PCI interrupt wiring
hw/isa/piix: Reuse PIIX3's PCI interrupt triggering in PIIX4
hw/isa/piix: Rename functions to be shared for PCI interrupt triggering
hw/isa/piix: Reuse PIIX3 base class' realize method in PIIX4
hw/isa/piix: Share PIIX3's base class with PIIX4
hw/isa/piix: Harmonize names of reset control memory regions
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, the one-shot (mode 1) PIT expires far too quickly,
due to the output being set under the wrong logic.
This change fixes the one-shot PIT mode to behave similarly to mode 0.
TESTED: using the one-shot PIT mode to calibrate a local apic timer.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Message-Id: <20230226015755.52624-1-damien@zamaudio.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The counter register is only 24-bits and counts down. If the timer is
running but the qtimer to reset it hasn't fired off yet, there is a chance
the regster read can return an invalid result.
Signed-off-by: Chris Rauer <crauer@google.com>
Message-id: 20230922181411.2697135-1-crauer@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 8137355e85 ("aspeed/timer: Fix behaviour running Linux")
introduced a MAX() expression to calculate the next timer deadline :
return calculate_time(t, MAX(MAX(t->match[0], t->match[1]), 0));
The second MAX() is not necessary since the compared values are an
unsigned and 0. Simply remove it and fix warning :
../hw/timer/aspeed_timer.c: In function ‘calculate_next’:
../include/qemu/osdep.h:396:31: warning: declaration of ‘_a’ shadows a previous local [-Wshadow=compatible-local]
396 | typeof(1 ? (a) : (b)) _a = (a), _b = (b); \
| ^~
../hw/timer/aspeed_timer.c:170:12: note: in expansion of macro ‘MAX’
170 | next = MAX(MAX(calculate_match(t, 0), calculate_match(t, 1)), 0);
| ^~~
../hw/timer/aspeed_timer.c:170:16: note: in expansion of macro ‘MAX’
170 | next = MAX(MAX(calculate_match(t, 0), calculate_match(t, 1)), 0);
| ^~~
/home/legoater/work/qemu/qemu-aspeed.git/include/qemu/osdep.h:396:31: note: shadowed declaration is here
396 | typeof(1 ? (a) : (b)) _a = (a), _b = (b); \
| ^~
../hw/timer/aspeed_timer.c:170:12: note: in expansion of macro ‘MAX’
170 | next = MAX(MAX(calculate_match(t, 0), calculate_match(t, 1)), 0);
| ^~~
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230922155924.1172019-5-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
