Patch 06b1297017 ("virtio-net: fix network stall under load")
added double-check to test whether the available buffer size
can satisfy the request or not, in case the guest has added
some buffers to the avail ring simultaneously after the first
check. It will be lucky if the available buffer size becomes
okay after the double-check, then the host can send the packet
to the guest. If the buffer size still can't satisfy the request,
even if the guest has added some buffers, viritio-net would
stall at the host side forever.
The patch enables notification and checks whether the guest has
added some buffers since last check of available buffers when
the available buffers are insufficient. If no buffer is added,
return false, else recheck the available buffers in the loop.
If the available buffers are sufficient, disable notification
and return true.
Changes:
1. Change the return type of virtqueue_get_avail_bytes() from void
to int, it returns an opaque that represents the shadow_avail_idx
of the virtqueue on success, else -1 on error.
2. Add a new API: virtio_queue_enable_notification_and_check(),
it takes an opaque as input arg which is returned from
virtqueue_get_avail_bytes(). It enables notification firstly,
then checks whether the guest has added some buffers since
last check of available buffers or not by virtio_queue_poll(),
return ture if yes.
The patch also reverts patch "06b1297017".
The case below can reproduce the stall.
Guest 0
+--------+
| iperf |
---------------> | server |
Host | +--------+
+--------+ | ...
| iperf |----
| client |---- Guest n
+--------+ | +--------+
| | iperf |
---------------> | server |
+--------+
Boot many guests from qemu with virtio network:
qemu ... -netdev tap,id=net_x \
-device virtio-net-pci-non-transitional,\
iommu_platform=on,mac=xx:xx:xx:xx:xx:xx,netdev=net_x
Each guest acts as iperf server with commands below:
iperf3 -s -D -i 10 -p 8001
iperf3 -s -D -i 10 -p 8002
The host as iperf client:
iperf3 -c guest_IP -p 8001 -i 30 -w 256k -P 20 -t 40000
iperf3 -c guest_IP -p 8002 -i 30 -w 256k -P 20 -t 40000
After some time, the host loses connection to the guest,
the guest can send packet to the host, but can't receive
packet from the host.
It's more likely to happen if SWIOTLB is enabled in the guest,
allocating and freeing bounce buffer takes some CPU ticks,
copying from/to bounce buffer takes more CPU ticks, compared
with that there is no bounce buffer in the guest.
Once the rate of producing packets from the host approximates
the rate of receiveing packets in the guest, the guest would
loop in NAPI.
receive packets ---
| |
v |
free buf virtnet_poll
| |
v |
add buf to avail ring ---
|
| need kick the host?
| NAPI continues
v
receive packets ---
| |
v |
free buf virtnet_poll
| |
v |
add buf to avail ring ---
|
v
... ...
On the other hand, the host fetches free buf from avail
ring, if the buf in the avail ring is not enough, the
host notifies the guest the event by writing the avail
idx read from avail ring to the event idx of used ring,
then the host goes to sleep, waiting for the kick signal
from the guest.
Once the guest finds the host is waiting for kick singal
(in virtqueue_kick_prepare_split()), it kicks the host.
The host may stall forever at the sequences below:
Host Guest
------------ -----------
fetch buf, send packet receive packet ---
... ... |
fetch buf, send packet add buf |
... add buf virtnet_poll
buf not enough avail idx-> add buf |
read avail idx add buf |
add buf ---
receive packet ---
write event idx ... |
wait for kick add buf virtnet_poll
... |
---
no more packet, exit NAPI
In the first loop of NAPI above, indicated in the range of
virtnet_poll above, the host is sending packets while the
guest is receiving packets and adding buffers.
step 1: The buf is not enough, for example, a big packet
needs 5 buf, but the available buf count is 3.
The host read current avail idx.
step 2: The guest adds some buf, then checks whether the
host is waiting for kick signal, not at this time.
The used ring is not empty, the guest continues
the second loop of NAPI.
step 3: The host writes the avail idx read from avail
ring to used ring as event idx via
virtio_queue_set_notification(q->rx_vq, 1).
step 4: At the end of the second loop of NAPI, recheck
whether kick is needed, as the event idx in the
used ring written by the host is beyound the
range of kick condition, the guest will not
send kick signal to the host.
Fixes: 06b1297017 ("virtio-net: fix network stall under load")
Cc: qemu-stable@nongnu.org
Signed-off-by: Wencheng Yang <east.moutain.yang@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit f937309fbd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context fixup in include/hw/virtio/virtio.h)
The unrealize functions of the various vhost-user devices are
calling the corresponding vhost_*_set_status() functions with a
status of 0 to shut down the device correctly.
Now these vhost_*_set_status() functions all follow this scheme:
bool should_start = virtio_device_should_start(vdev, status);
if (vhost_dev_is_started(&vvc->vhost_dev) == should_start) {
return;
}
if (should_start) {
/* ... do the initialization stuff ... */
} else {
/* ... do the cleanup stuff ... */
}
The problem here is virtio_device_should_start(vdev, 0) currently
always returns "true" since it internally only looks at vdev->started
instead of looking at the "status" parameter. Thus once the device
got started once, virtio_device_should_start() always returns true
and thus the vhost_*_set_status() functions return early, without
ever doing any clean-up when being called with status == 0. This
causes e.g. problems when trying to hot-plug and hot-unplug a vhost
user devices multiple times since the de-initialization step is
completely skipped during the unplug operation.
This bug has been introduced in commit 9f6bcfd99f ("hw/virtio: move
vm_running check to virtio_device_started") which replaced
should_start = status & VIRTIO_CONFIG_S_DRIVER_OK;
with
should_start = virtio_device_started(vdev, status);
which later got replaced by virtio_device_should_start(). This blocked
the possibility to set should_start to false in case the status flag
VIRTIO_CONFIG_S_DRIVER_OK was not set.
Fix it by adjusting the virtio_device_should_start() function to
only consider the status flag instead of vdev->started. Since this
function is only used in the various vhost_*_set_status() functions
for exactly the same purpose, it should be fine to fix it in this
central place there without any risk to change the behavior of other
code.
Fixes: 9f6bcfd99f ("hw/virtio: move vm_running check to virtio_device_started")
Buglink: https://issues.redhat.com/browse/RHEL-40708
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240618121958.88673-1-thuth@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit d72479b117)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit dfcf74fa ("virtio-gpu: fix scanout migration post-load") broke
forward/backward version migration. Versioning of nested VMSD structures
is not straightforward, as the wire format doesn't have nested
structures versions. Introduce x-scanout-vmstate-version and a field
test to save/load appropriately according to the machine version.
Fixes: dfcf74fa ("virtio-gpu: fix scanout migration post-load")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Fiona Ebner <f.ebner@proxmox.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
[fixed long lines]
Signed-off-by: Fabiano Rosas <farosas@suse.de>
(cherry picked from commit 40a23ef643)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Introduce virtio_bh_new_guarded(), similar to qemu_bh_new_guarded()
but using the transport memory guard, instead of the device one
(there can only be one virtio device per virtio bus).
Inspired-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20240409105537.18308-2-philmd@linaro.org>
The current handling of invalid virtqueue elements inside the TX/RX virt
queue handlers is wrong.
They are added in a per-stream invalid queue to be processed after the
handler is done examining each message, but the invalid message might
not be specifying any stream_id; which means it's invalid to add it to
any stream->invalid queue since stream could be NULL at this point.
This commit moves the invalid queue to the VirtIOSound struct which
guarantees there will always be a valid temporary place to store them
inside the tx/rx handlers. The queue will be emptied before the handler
returns, so the queue must be empty at any other point of the device's
lifetime.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <virtio-snd-rewrite-invalid-tx-rx-message-handling-v1.manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit cd341fd1ff.
The patch adds non-upstream code in
include/standard-headers/linux/virtio_pci.h
which would make maintainance harder.
Revert for now.
Suggested-by: Jason Wang <jasowang@redhat.com>
Message-Id: <df6b6b465753e754a19459e8cd61416548f89a42.1712569644.git.mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let clock_set_mul_div() return a boolean value whether the
clock has been updated or not, similarly to clock_set().
Return early when clock_set_mul_div() is called with
same mul/div values the clock has.
Acked-by: Luc Michel <luc@lmichel.fr>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20240325152827.73817-2-philmd@linaro.org>
The PCA9552 and PCA9554 devices are both I2C GPIO controllers and the
PCA9552 also can drive LEDs. Do all the necessary adjustments to move
the models under hw/gpio.
Cc: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20240325134833.1484265-1-clg@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
* user device fixes for Aspeed and PowerNV machines
* coverity fix for iommufd
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmX5mm0ACgkQUaNDx8/7
7KE/MQ/9GeX4yNBxY2iTATdmPXwjMw8AtKyfIQb605nIO0ch1Z98ywl5VMwCNohn
ppY9L5bFpEASgRlFVm73X4DGxKyRGpRPqylsvINh0hKciRpmRkELHY3llhnXsd7P
Q197pDtFr54FeX8j4+hSAu4paT97fPENlKn0J6lto2I1cXGcD1LYNDFhysoXdGme
brJgo7KjQJZPZ560ZewskL5FWf3G9EkRjpqd8y0G5OtNmAPgAaahOMHhDCXan182
J89I9CHI5xN45MRfAs8JamSaj/GyNsr4h04WhPa0+VZQ5vsaeW2Ekt4ypj+oAV+p
wykhYzQk4ALZcmmph2flSAtLa7uheI+imyqubMthQCDj3G8onSQBMd5/4WRK6O49
0oE1DpPDEfhlJEQYxaYhOeqeA9iaP+w6V+yE+L5oGlMO66cR7GZsPu0x7kXailbH
IoHw9mO+vMkpuyeP7M3hA8WRFCdFpf1Nn1Ao5Jz3KoiTyJWlIvX5VSaj12sjddQ2
fU9SKu2Q5QqS5uQGakkY64EyUy7RkGIX6zY2NIscVe2lfAfKf3mZwu7OIuLjEy5O
lRn35vWV8fOdRooKoDPTNcdBCaNPi+RApin8chOv5P+F+ie7+Twf9sb1AgH/pIcv
HptvTXbvSFNbbdb+OE8a5qsqTvnrN8d31IXzrWRYsJB07x2IyoA=
=zR3v
-----END PGP SIGNATURE-----
Merge tag 'pull-for-9.0-20240319' of https://github.com/legoater/qemu into staging
aspeed, pnv, vfio queue:
* user device fixes for Aspeed and PowerNV machines
* coverity fix for iommufd
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmX5mm0ACgkQUaNDx8/7
# 7KE/MQ/9GeX4yNBxY2iTATdmPXwjMw8AtKyfIQb605nIO0ch1Z98ywl5VMwCNohn
# ppY9L5bFpEASgRlFVm73X4DGxKyRGpRPqylsvINh0hKciRpmRkELHY3llhnXsd7P
# Q197pDtFr54FeX8j4+hSAu4paT97fPENlKn0J6lto2I1cXGcD1LYNDFhysoXdGme
# brJgo7KjQJZPZ560ZewskL5FWf3G9EkRjpqd8y0G5OtNmAPgAaahOMHhDCXan182
# J89I9CHI5xN45MRfAs8JamSaj/GyNsr4h04WhPa0+VZQ5vsaeW2Ekt4ypj+oAV+p
# wykhYzQk4ALZcmmph2flSAtLa7uheI+imyqubMthQCDj3G8onSQBMd5/4WRK6O49
# 0oE1DpPDEfhlJEQYxaYhOeqeA9iaP+w6V+yE+L5oGlMO66cR7GZsPu0x7kXailbH
# IoHw9mO+vMkpuyeP7M3hA8WRFCdFpf1Nn1Ao5Jz3KoiTyJWlIvX5VSaj12sjddQ2
# fU9SKu2Q5QqS5uQGakkY64EyUy7RkGIX6zY2NIscVe2lfAfKf3mZwu7OIuLjEy5O
# lRn35vWV8fOdRooKoDPTNcdBCaNPi+RApin8chOv5P+F+ie7+Twf9sb1AgH/pIcv
# HptvTXbvSFNbbdb+OE8a5qsqTvnrN8d31IXzrWRYsJB07x2IyoA=
# =zR3v
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 19 Mar 2024 14:00:13 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-for-9.0-20240319' of https://github.com/legoater/qemu:
aspeed/smc: Only wire flash devices at reset
ppc/pnv: I2C controller is not user creatable
vfio/iommufd: Fix memory leak
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed machines have many Static Memory Controllers (SMC), up to
8, which can only drive flash memory devices. Commit 27a2c66c92
("aspeed/smc: Wire CS lines at reset") tried to ease the definitions
of these devices by allowing flash devices from the command line to be
attached to a SSI bus. For that, the wiring of the CS lines of the
Aspeed SMC controller was moved at reset. Two assumptions are made
though, first that the device has a SSI_GPIO_CS GPIO line, which is
not always the case, and second that it is a flash device.
Correct this problem by ensuring that the devices attached to the bus
are of the correct flash type. This fixes a QEMU abort when devices
without a CS line, such as the max111x, are passed on the command
line.
While at it, export TYPE_M25P80 used in the Xilinx Versal Virtual
machine.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2228
Fixes: 27a2c66c92 ("aspeed/smc: Wire CS lines at reset")
Reported-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
[ clg: minor fixes in the commit log ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-14-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current code uses mix of error_report()+exit(1)
and error_setg() to handle errors.
Use newer error_setg() everywhere, beside consistency
it will allow to detect error condition without killing
QEMU and attempt switch-over to SMBIOS3.x tables/entrypoint
in follow up patch.
while at it, clear smbios_tables pointer after freeing.
that will avoid double free if smbios_get_tables() is called
multiple times.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-13-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
basically moving code around without functional change.
And exposing some symbols so that they could be shared
between smbbios.c and new smbios_legacy.c
plus some meson magic to build smbios_legacy.c only
for 'pc' machine and otherwise replace it with stub
if not selected.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-12-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As a preparation to move legacy handling into a separate file,
add prefix 'smbios_' to type0/type1/have_binfile_bitmap/have_fields_bitmap
and expose them in smbios.h so that they can be reused in
legacy and modern code.
Doing it as a separate patch to avoid rename cluttering follow-up
patch which will move legacy code into a separate file.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-11-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
legacy mode doesn't support structures of type 2 and more,
and CLI has a check for '-smbios type' option, however it's
still possible to sneak in type4 as a blob with '-smbios file'
option. However doing the later makes SMBIOS tables broken
since SeaBIOS doesn't expect that.
Rather than trying to add support for type4 to legacy code
(both QEMU and SeaBIOS), simplify smbios_get_table_legacy()
by dropping not relevant check in legacy code and error out
on type4 blob.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
clean up smbios_set_defaults() which is reused by legacy
and non legacy machines from being aware of 'legacy' notion
and need to turn it off. And push legacy handling up to
PC machine code where it's relevant.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Acked-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it makes smbios_validate_table() independent from
smbios_smp_sockets global, which in turn lets
smbios_get_tables() avoid using not related legacy code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
more memslots support in libvhost-user
support PCIe Gen5/Gen6 link speeds in pcie
more traces in vdpa
network simulation devices support in vdpa
SMBIOS type 9 descriptor implementation
Bump max_cpus to 4096 vcpus in q35
aw-bits and granule options in VIRTIO-IOMMU
Support report NUMA nodes for device memory using GI in acpi
Beginning of shutdown event support in pvpanic
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXw0TMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp8x4H+gLMoGwaGAX7gDGPgn2Ix4j/3kO77ZJ9X9k/
1KqZu/9eMS1j2Ei+vZqf05w7qRjxxhwDq3ilEXF/+UFqgAehLqpRRB8j5inqvzYt
+jv0DbL11PBp/oFjWcytm5CbiVsvq8KlqCF29VNzc162XdtcduUOWagL96y8lJfZ
uPrOoyeR7SMH9lp3LLLHWgu+9W4nOS03RroZ6Umj40y5B7yR0Rrppz8lMw5AoQtr
0gMRnFhYXeiW6CXdz+Tzcr7XfvkkYDi/j7ibiNSURLBfOpZa6Y8+kJGKxz5H1K1G
6ZY4PBcOpQzl+NMrktPHogczgJgOK10t+1i/R3bGZYw2Qn/93Eg=
=C0UU
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
more memslots support in libvhost-user
support PCIe Gen5/Gen6 link speeds in pcie
more traces in vdpa
network simulation devices support in vdpa
SMBIOS type 9 descriptor implementation
Bump max_cpus to 4096 vcpus in q35
aw-bits and granule options in VIRTIO-IOMMU
Support report NUMA nodes for device memory using GI in acpi
Beginning of shutdown event support in pvpanic
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXw0TMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp8x4H+gLMoGwaGAX7gDGPgn2Ix4j/3kO77ZJ9X9k/
# 1KqZu/9eMS1j2Ei+vZqf05w7qRjxxhwDq3ilEXF/+UFqgAehLqpRRB8j5inqvzYt
# +jv0DbL11PBp/oFjWcytm5CbiVsvq8KlqCF29VNzc162XdtcduUOWagL96y8lJfZ
# uPrOoyeR7SMH9lp3LLLHWgu+9W4nOS03RroZ6Umj40y5B7yR0Rrppz8lMw5AoQtr
# 0gMRnFhYXeiW6CXdz+Tzcr7XfvkkYDi/j7ibiNSURLBfOpZa6Y8+kJGKxz5H1K1G
# 6ZY4PBcOpQzl+NMrktPHogczgJgOK10t+1i/R3bGZYw2Qn/93Eg=
# =C0UU
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Mar 2024 22:03:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (68 commits)
docs/specs/pvpanic: document shutdown event
hw/cxl: Fix missing reserved data in CXL Device DVSEC
hmat acpi: Fix out of bounds access due to missing use of indirection
hmat acpi: Do not add Memory Proximity Domain Attributes Structure targetting non existent memory.
qemu-options.hx: Document the virtio-iommu-pci aw-bits option
hw/arm/virt: Set virtio-iommu aw-bits default value to 48
hw/i386/q35: Set virtio-iommu aw-bits default value to 39
virtio-iommu: Add an option to define the input range width
virtio-iommu: Trace domain range limits as unsigned int
qemu-options.hx: Document the virtio-iommu-pci granule option
virtio-iommu: Change the default granule to the host page size
virtio-iommu: Add a granule property
hw/i386/acpi-build: Add support for SRAT Generic Initiator structures
hw/acpi: Implement the SRAT GI affinity structure
qom: new object to associate device to NUMA node
hw/i386/pc: Inline pc_cmos_init() into pc_cmos_init_late() and remove it
hw/i386/pc: Set "normal" boot device order in pc_basic_device_init()
hw/i386/pc: Avoid one use of the current_machine global
hw/i386/pc: Remove "rtc_state" link again
Revert "hw/i386/pc: Confine system flash handling to pc_sysfw"
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/core/machine.c
The r3.1 specification introduced a new 2 byte field, but
to maintain DWORD alignment, a additional 2 reserved bytes
were added. Forgot those in updating the structure definition
but did include them in the size define leading to a buffer
overrun.
Also use the define so that we don't duplicate the value.
Fixes: Coverity ID 1534095 buffer overrun
Fixes: 8700ee15de ("hw/cxl: Standardize all references on CXL r3.1 and minor updates")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240308143831.6256-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
aw-bits is a new option that allows to set the bit width of
the input address range. This value will be used as a default for
the device config input_range.end. By default it is set to 64 bits
which is the current value.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240307134445.92296-7-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows to choose which granule will be used by
default by the virtio-iommu. Current page size mask
default is qemu_target_page_mask so this translates
into a 4k granule on ARM and x86_64 where virtio-iommu
is supported.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240307134445.92296-3-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI spec provides a scheme to associate "Generic Initiators" [1]
(e.g. heterogeneous processors and accelerators, GPUs, and I/O devices with
integrated compute or DMA engines GPUs) with Proximity Domains. This is
achieved using Generic Initiator Affinity Structure in SRAT. During bootup,
Linux kernel parse the ACPI SRAT to determine the PXM ids and create a NUMA
node for each unique PXM ID encountered. Qemu currently do not implement
these structures while building SRAT.
Add GI structures while building VM ACPI SRAT. The association between
device and node are stored using acpi-generic-initiator object. Lookup
presence of all such objects and use them to build these structures.
The structure needs a PCI device handle [2] that consists of the device BDF.
The vfio-pci device corresponding to the acpi-generic-initiator object is
located to determine the BDF.
[1] ACPI Spec 6.3, Section 5.2.16.6
[2] ACPI Spec 6.3, Table 5.80
Cc: Jonathan Cameron <qemu-devel@nongnu.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Cedric Le Goater <clg@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ankit Agrawal <ankita@nvidia.com>
Message-Id: <20240308145525.10886-3-ankita@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NVIDIA GPU's support MIG (Mult-Instance GPUs) feature [1], which allows
partitioning of the GPU device resources (including device memory) into
several (upto 8) isolated instances. Each of the partitioned memory needs
a dedicated NUMA node to operate. The partitions are not fixed and they
can be created/deleted at runtime.
Unfortunately Linux OS does not provide a means to dynamically create/destroy
NUMA nodes and such feature implementation is not expected to be trivial. The
nodes that OS discovers at the boot time while parsing SRAT remains fixed. So
we utilize the Generic Initiator (GI) Affinity structures that allows
association between nodes and devices. Multiple GI structures per BDF is
possible, allowing creation of multiple nodes by exposing unique PXM in each
of these structures.
Implement the mechanism to build the GI affinity structures as Qemu currently
does not. Introduce a new acpi-generic-initiator object to allow host admin
link a device with an associated NUMA node. Qemu maintains this association
and use this object to build the requisite GI Affinity Structure.
When multiple NUMA nodes are associated with a device, it is required to
create those many number of acpi-generic-initiator objects, each representing
a unique device:node association.
Following is one of a decoded GI affinity structure in VM ACPI SRAT.
[0C8h 0200 1] Subtable Type : 05 [Generic Initiator Affinity]
[0C9h 0201 1] Length : 20
[0CAh 0202 1] Reserved1 : 00
[0CBh 0203 1] Device Handle Type : 01
[0CCh 0204 4] Proximity Domain : 00000007
[0D0h 0208 16] Device Handle : 00 00 20 00 00 00 00 00 00 00 00
00 00 00 00 00
[0E0h 0224 4] Flags (decoded below) : 00000001
Enabled : 1
[0E4h 0228 4] Reserved2 : 00000000
[0E8h 0232 1] Subtable Type : 05 [Generic Initiator Affinity]
[0E9h 0233 1] Length : 20
An admin can provide a range of acpi-generic-initiator objects, each
associating a device (by providing the id through pci-dev argument)
to the desired NUMA node (using the node argument). Currently, only PCI
device is supported.
For the grace hopper system, create a range of 8 nodes and associate that
with the device using the acpi-generic-initiator object. While a configuration
of less than 8 nodes per device is allowed, such configuration will prevent
utilization of the feature to the fullest. The following sample creates 8
nodes per PCI device for a VM with 2 PCI devices and link them to the
respecitve PCI device using acpi-generic-initiator objects:
-numa node,nodeid=2 -numa node,nodeid=3 -numa node,nodeid=4 \
-numa node,nodeid=5 -numa node,nodeid=6 -numa node,nodeid=7 \
-numa node,nodeid=8 -numa node,nodeid=9 \
-device vfio-pci-nohotplug,host=0009:01:00.0,bus=pcie.0,addr=04.0,rombar=0,id=dev0 \
-object acpi-generic-initiator,id=gi0,pci-dev=dev0,node=2 \
-object acpi-generic-initiator,id=gi1,pci-dev=dev0,node=3 \
-object acpi-generic-initiator,id=gi2,pci-dev=dev0,node=4 \
-object acpi-generic-initiator,id=gi3,pci-dev=dev0,node=5 \
-object acpi-generic-initiator,id=gi4,pci-dev=dev0,node=6 \
-object acpi-generic-initiator,id=gi5,pci-dev=dev0,node=7 \
-object acpi-generic-initiator,id=gi6,pci-dev=dev0,node=8 \
-object acpi-generic-initiator,id=gi7,pci-dev=dev0,node=9 \
-numa node,nodeid=10 -numa node,nodeid=11 -numa node,nodeid=12 \
-numa node,nodeid=13 -numa node,nodeid=14 -numa node,nodeid=15 \
-numa node,nodeid=16 -numa node,nodeid=17 \
-device vfio-pci-nohotplug,host=0009:01:01.0,bus=pcie.0,addr=05.0,rombar=0,id=dev1 \
-object acpi-generic-initiator,id=gi8,pci-dev=dev1,node=10 \
-object acpi-generic-initiator,id=gi9,pci-dev=dev1,node=11 \
-object acpi-generic-initiator,id=gi10,pci-dev=dev1,node=12 \
-object acpi-generic-initiator,id=gi11,pci-dev=dev1,node=13 \
-object acpi-generic-initiator,id=gi12,pci-dev=dev1,node=14 \
-object acpi-generic-initiator,id=gi13,pci-dev=dev1,node=15 \
-object acpi-generic-initiator,id=gi14,pci-dev=dev1,node=16 \
-object acpi-generic-initiator,id=gi15,pci-dev=dev1,node=17 \
Link: https://www.nvidia.com/en-in/technologies/multi-instance-gpu [1]
Cc: Jonathan Cameron <qemu-devel@nongnu.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Ankit Agrawal <ankita@nvidia.com>
Message-Id: <20240308145525.10886-2-ankita@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that pc_cmos_init() doesn't populate the X86MachineState::rtc attribute any
longer, its duties can be merged into pc_cmos_init_late() which is called within
machine_done notifier. This frees pc_piix and pc_q35 from explicit CMOS
initialization.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240303185332.1408-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Specifying the property `-M pflash0` results in a regression:
qemu-system-x86_64: Property 'pc-q35-9.0-machine.pflash0' not found
Revert the change for now until a solution is found.
This reverts commit 6f6ad2b245.
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240226215909.30884-3-shentey@gmail.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pcie_sriov_pf_disable_vfs() is called when resetting the PF, but it only
disables VFs and does not reset SR-IOV extended capability, leaking the
state and making the VF Enable register inconsistent with the actual
state.
Replace pcie_sriov_pf_disable_vfs() with pcie_sriov_pf_reset(), which
does not only disable VFs but also resets the capability.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-3-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@ericsson.com>
Signed-off-by: Felix Wu <flwu@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Message-Id: <20240221170027.1027325-3-nabihestefan@google.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version 2.1+.
Signed-off-by: Felix Wu <flwu@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Message-Id: <20240221170027.1027325-2-nabihestefan@google.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds support for VDPA network simulation devices.
The device is developed based on virtio-net and tap backend,
and supports hardware live migration function.
For more details, please refer to "docs/system/devices/vdpa-net.rst"
Signed-off-by: Hao Chen <chenh@yusur.tech>
Message-Id: <20240221073802.2888022-1-chenh@yusur.tech>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The payload size returned by command VIRTIO_SND_R_PCM_INFO is
wrong. The code in process_cmd() assumes that all commands
return only a virtio_snd_hdr payload, but some commands like
VIRTIO_SND_R_PCM_INFO may return an additional payload.
Add a zero initialized payload_size variable to struct
virtio_snd_ctrl_command to allow for additional payloads.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20240218083351.8524-1-vr_qemu@t-online.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This CXL component isn't allowed to have a RAS capability.
Whilst this should be harmless as software is not expected to look
here, good to clean it up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240215155206.2736-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch extends the PCIe link speed option so that slots can be
configured as supporting 32GT/s (Gen5) or 64GT/s (Gen5) speeds.
This is as simple as setting the appropriate bit in LnkCap2 and
the appropriate value in LnkCap and LnkCtl2.
Signed-off-by: Lukas Stockner <lstockner@genesiscloud.com>
Message-Id: <20240215012326.3272366-1-lstockner@genesiscloud.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Will be used in following patches.
DISABLING(-1) means SVQ is being switched off to passthrough
mode.
ENABLING(1) means passthrough VQs are being switched to SVQ.
DONE(0) means SVQ switching is completed.
Message-Id: <1707910082-10243-11-git-send-email-si-wei.liu@oracle.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Prefer fast cpu_env() over slower CPU QOM cast macro
-----BEGIN PGP SIGNATURE-----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=NiP4
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-03-12' of https://gitlab.com/thuth/qemu into staging
* Add missing ERRP_GUARD() statements in functions that need it
* Prefer fast cpu_env() over slower CPU QOM cast macro
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmXwPhYRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWHvBAAgKx5LHFjz3xREVA+LkDTQ49mz0lK3s32
# SGvNlIHjiaDGVttVYhVC4sinBWUruG4Lyv/2QN72OJBzn6WUsEUQE3KPH1d7Y3/s
# wS9X7mj70n4kugWJqeIJP5AXSRasHmWoQ4QJLVQRJd6+Eb9jqwep0x7bYkI1de6D
# bL1Q7bIfkFeNQBXaiPWAm2i+hqmT4C1r8HEAGZIjAsMFrjy/hzBEjNV+pnh6ZSq9
# Vp8BsPWRfLU2XHm4WX0o8d89WUMAfUGbVkddEl/XjIHDrUD+Zbd1HAhLyfhsmrnE
# jXIwSzm+ML1KX4MoF5ilGtg8Oo0gQDEBy9/xck6G0HCm9lIoLKlgTxK9glr2vdT8
# yxZmrM9Hder7F9hKKxmb127xgU6AmL7rYmVqsoQMNAq22D6Xr4UDpgFRXNk2/wO6
# zZZBkfZ4H4MpZXbd/KJpXvYH5mQA4IpkOy8LJdE+dbcHX7Szy9ksZdPA+Z10hqqf
# zqS13qTs3abxymy2Q/tO3hPKSJCk1+vCGUkN60Wm+9VoLWGoU43qMc7gnY/pCS7m
# 0rFKtvfwFHhokX1orK0lP/ppVzPv/5oFIeK8YDY9if+N+dU2LCwVZHIuf2/VJPRq
# wmgH2vAn3JDoRKPxTGX9ly6AMxuZaeP92qBTOPap0gDhihYzIpaCq9ecEBoTakI7
# tdFhV0iRr08=
# =NiP4
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Mar 2024 11:35:50 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-03-12' of https://gitlab.com/thuth/qemu: (55 commits)
user: Prefer fast cpu_env() over slower CPU QOM cast macro
target/xtensa: Prefer fast cpu_env() over slower CPU QOM cast macro
target/tricore: Prefer fast cpu_env() over slower CPU QOM cast macro
target/sparc: Prefer fast cpu_env() over slower CPU QOM cast macro
target/sh4: Prefer fast cpu_env() over slower CPU QOM cast macro
target/rx: Prefer fast cpu_env() over slower CPU QOM cast macro
target/ppc: Prefer fast cpu_env() over slower CPU QOM cast macro
target/openrisc: Prefer fast cpu_env() over slower CPU QOM cast macro
target/nios2: Prefer fast cpu_env() over slower CPU QOM cast macro
target/mips: Prefer fast cpu_env() over slower CPU QOM cast macro
target/microblaze: Prefer fast cpu_env() over slower CPU QOM cast macro
target/m68k: Prefer fast cpu_env() over slower CPU QOM cast macro
target/loongarch: Prefer fast cpu_env() over slower CPU QOM cast macro
target/i386/hvf: Use CPUState typedef
target/hexagon: Prefer fast cpu_env() over slower CPU QOM cast macro
target/cris: Prefer fast cpu_env() over slower CPU QOM cast macro
target/avr: Prefer fast cpu_env() over slower CPU QOM cast macro
target/alpha: Prefer fast cpu_env() over slower CPU QOM cast macro
target: Replace CPU_GET_CLASS(cpu -> obj) in cpu_reset_hold() handler
bulk: Call in place single use cpu_env()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a SPAPR capability cap-nested-papr which enables nested PAPR
API for nested guests. This new API is to enable support for KVM on PowerVM
and the support in Linux kernel has already merged upstream.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
For nested PAPR API, we use SpaprMachineStateNestedGuest struct to store
partition table info, use the same in spapr_get_pate_nested() via
helper.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcalls:
- H_GUEST_GET_STATE which is used to get state of a nested guest or
a guest VCPU. The value field for each element in the request is
destination to be updated to reflect current state on success.
- H_GUEST_SET_STATE which is used to modify the state of a guest or
a guest VCPU. On success, guest (or its VCPU) state shall be
updated as per the value field for the requested element(s).
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Nested PAPR API provides a standard Guest State Buffer (GSB) format
with unique IDs for each guest state element for which get/set state is
supported by the API. Some of the elements are read-only and/or guest-wide.
Introducing additional required GSB elements and helper routines for state
exchange of each of the nested guest state elements for which get/set state
should be supported by the API.
[amachhiw: set the PCR whenever logical PVR is set]
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Currently, nested_ppc_state stores a certain set of registers and works
with nested_[load|save]_state() for state transfer as reqd for nested-hv API.
Extending these with additional registers state as reqd for nested PAPR API.
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcall H_GUEST_CREATE_VCPU which is used to
create and initialize the specified VCPU resource for the previously
created guest. Each guest can have multiple VCPUs upto max 2048.
All VCPUs for a guest gets deallocated on guest delete.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcalls:
- H_GUEST_CREATE which is used to create and allocate resources for
nested guest being created.
- H_GUEST_DELETE which is used to delete and deallocate resources
for the nested guest being deleted. It also supports deleting all nested
guests at once using a deleteAll flag.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcalls:
- H_GUEST_GET_CAPABILITIES which is used to query the capabilities
of the API and the L2 guests it provides.
- H_GUEST_SET_CAPABILITIES which is used to set the Guest API
capabilities that the Host Partition supports and may use.
[amachhiw: support for p9 compat mode and return register bug fixes]
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
spapr_exit_nested and spapr_get_pate_nested_hv contains code which
is specific to nested-hv API. Isolating code flows based on API
helps extending it to be used with different API as well.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Currently, nested_ptcr is being used by existing nested-hv API to store
nested guest related info. This need to be organised to extend support
for the nested PAPR API which would need to store additional info
related to nested guests in next series of patches.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Most of the nested code has already been moved to spapr_nested.c
This logic inside spapr_get_pate is related to nested guests and
better suited for spapr_nested.c, hence moving there.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Since cap-nested-hv is an optional capability, it makes sense to register
api specfic hcalls only when respective capability is enabled. This
requires to introduce a new API to unregister hypercalls to maintain
sanity across guest reboot since caps are re-applied across reboots and
re-registeration of hypercalls would hit assert otherwise.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Big (SMT8) cores have a complicated function to map the core, thread ID
to pervasive topology (PIR). Fix this for power8, power9, and power10.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The current post-loading code for scanout has a FIXME: it doesn't take
the resource region/rect into account. But there is more, when adding
blob migration support in commit f66767f75c, I didn't realize that blob
resources could be used for scanouts. This situationn leads to a crash
during post-load, as they don't have an associated res->image.
virtio_gpu_do_set_scanout() handle all cases, but requires the
associated virtio_gpu_framebuffer, which is currently not saved during
migration.
Add a v2 of "virtio-gpu-one-scanout" with the framebuffer fields, so we
can restore blob scanouts, as well as fixing the existing FIXME.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Sebastian Ott <sebott@redhat.com>
