mirror of
https://github.com/SoftFever/OrcaSlicer.git
synced 2025-07-16 19:28:14 -06:00
c2eda0b0fa
* Add process images * Reorder like GUI + images * GUI images subfolder * MVF restandarizarion (naming pending) Update volumetric speed calibration docs and image paths * Improved SVGs * Infill Wall Overlap * Apply gap fill + Anchor * Minor change * Internal Solid Infill * Images++ * Step file import image update * Add VFA calibration documentation and images * fix pa-tower image not visible * Removed WIP in not implemented features. * Added Old and New Order in xlsx * Wall generator * Wiki #9924 * New Zag Infills Co-Authored-By: Rodrigo <162915171+RF47@users.noreply.github.com> * Infill Rescaled images + sharpness 2d honeycomb image fix * Update infill_desc_calculator.xlsx * Rename extrusion rate smoothing references for consistency * Add wiki and link for top/bottom shells settings * Updated Wiki Links tab.cpp * Update infill_desc_calculator.xlsx * Fix indentation in top/bottom shells option group * Fill images optimized Removed Metadata Reduce color bit to 16 --------- Co-authored-by: Rodrigo <162915171+RF47@users.noreply.github.com>
131 lines
7 KiB
Markdown
131 lines
7 KiB
Markdown
# Input Shaping
|
|
|
|
During high-speed movements, vibrations can cause a phenomenon called "ringing," where periodic ripples appear on the print surface. Input Shaping provides an effective solution by counteracting these vibrations, improving print quality and reducing wear on components without needing to significantly lower print speeds.
|
|
|
|
- [Klipper](#klipper)
|
|
- [Resonance Compensation](#resonance-compensation)
|
|
- [Marlin](#marlin)
|
|
- [ZV Input Shaping](#zv-input-shaping)
|
|
- [Fixed-Time Motion](#fixed-time-motion)
|
|
|
|
## Klipper
|
|
|
|
### Resonance Compensation
|
|
|
|
The Klipper Resonance Compensation is a set of Input Shaping modes that can be used to reduce ringing and improve print quality.
|
|
Ussualy the recommended values modes are `MZV` or `EI` for Delta printers.
|
|
|
|
1. Pre-requisites:
|
|
1. In OrcaSlicer, set:
|
|
1. Acceleration high enough to trigger ringing (e.g., 2000 mm/s²).
|
|
2. Speed high enough to trigger ringing (e.g., 100 mm/s).
|
|
|
|
> [!NOTE]
|
|
> These settings depend on your printer's motion ability and the filament's max volumetric speed. If you can't reach speeds that cause ringing, try increasing the filament's max volumetric speed (avoid materials below 10 mm³/s).
|
|
3. Jerk [Klipper Square Corner Velocity](https://www.klipper3d.org/Kinematics.html?h=square+corner+velocity#look-ahead) to 5 or a high value (e.g., 20).
|
|
|
|
2. In printer settigs:
|
|
1. Set the Shaper Type to `MZV` or `EI`.
|
|
```gcode
|
|
SET_INPUT_SHAPER SHAPER_TYPE=MZV
|
|
```
|
|
2. Disable [Minimun Cruise Ratio](https://www.klipper3d.org/Kinematics.html#minimum-cruise-ratio) with:
|
|
```gcode
|
|
SET_VELOCITY_LIMIT MINIMUM_CRUISE_RATIO=0
|
|
```
|
|
3. Use an opaque, high-gloss filament to make the ringing more visible.
|
|
2. Print the Input Shaping Frequency test with a range of frequencies.
|
|
|
|
|
|
|
|
1. Measure the X and Y heights and read the frequency set at that point in Orca Slicer.
|
|
|
|
|
|
|
|
|
|
2. If not a clear result, you can measure a X and Y min and max acceptable heights and repeat the test with that min and max value.
|
|
|
|
> [!WARNING]
|
|
> There is a chance you will need to set higher than 60Hz frequencies. Some printers with very rigid frames and excellent mechanics may exhibit frequencies exceeding 100Hz.
|
|
|
|
3. Print the Damping test setting your X and Y frequency to the value you found in the previous step.
|
|
|
|
|
|
|
|
1. Measure the X and Y heights and read the damping set at that point in Orca Slicer.
|
|
|
|
|
|
|
|
|
|
> [!IMPORTANT]
|
|
> Not all Resonance Compensation modes support damping.
|
|
|
|
4. Restore your 3D Printer settings to avoid keep using high acceleration and jerk values.
|
|
5. Save the settings
|
|
1. You need to go to the printer settings and set the X and Y frequency and damp to the value you found in the previous step.
|
|
|
|
## Marlin
|
|
|
|
### ZV Input Shaping
|
|
|
|
ZV Input Shaping introduces an anti-vibration signal into the stepper motion for the X and Y axes. It works by splitting the step count into two halves: the first at half the frequency and the second as an "echo," delayed by half the ringing interval. This simple approach effectively reduces vibrations, improving print quality and allowing for higher speeds.
|
|
|
|
1. Pre-requisites:
|
|
1. In OrcaSlicer, set:
|
|
1. Acceleration high enough to trigger ringing (e.g., 2000 mm/s²).
|
|
2. Speed high enough to trigger ringing (e.g., 100 mm/s).
|
|
|
|
> [!NOTE]
|
|
> These settings depend on your printer's motion ability and the filament's max volumetric speed. If you can't reach speeds that cause ringing, try increasing the filament's max volumetric speed (avoid materials below 10 mm³/s).
|
|
|
|
3. Jerk
|
|
1. If using [Classic Jerk](https://marlinfw.org/docs/configuration/configuration.html#jerk-) use a high value (e.g., 20).
|
|
2. If using [Junction Deviation](https://marlinfw.org/docs/features/junction_deviation.html) (new Marlin default mode) this test will use 0.25 (high enough to most printers).
|
|
2. Use an opaque, high-gloss filament to make the ringing more visible.
|
|
2. Print the Input Shaping Frequency test with a range of frequencies.
|
|
|
|
|
|
|
|
1. Measure the X and Y heights and read the frequency set at that point in Orca Slicer.
|
|
|
|
|
|
|
|
|
|
2. If not a clear result, you can measure a X and Y min and max acceptable heights and repeat the test with that min and max value.
|
|
|
|
> [!WARNING]
|
|
> There is a chance you will need to set higher than 60Hz frequencies. Some printers with very rigid frames and excellent mechanics may exhibit frequencies exceeding 100Hz.
|
|
|
|
3. Print the Damping test setting your X and Y frequency to the value you found in the previous step.
|
|
|
|
|
|
|
|
1. Measure the X and Y heights and read the damping set at that point in Orca Slicer.
|
|
|
|
|
|
|
|
|
|
4. Restore your 3D Printer settings to avoid keep using high acceleration and jerk values.
|
|
1. Reboot your printer.
|
|
2. Use the following G-code to restore your printer settings:
|
|
```gcode
|
|
M501
|
|
```
|
|
5. Save the settings
|
|
1. You need to go to the printer settings and set the X and Y frequency and damp to the value you found in the previous step.
|
|
2. Use the following G-code to set the frequency:
|
|
```gcode
|
|
M593 X F#Xfrequency D#XDamping
|
|
M593 Y F#Yfrequency D#YDamping
|
|
M500
|
|
```
|
|
Example
|
|
```gcode
|
|
M593 X F37.25 D0.16
|
|
M593 Y F37.5 D0.06
|
|
M500
|
|
```
|
|
|
|
### Fixed-Time Motion
|
|
|
|
TODO: This calibration test is currently under development. See the [Marlin documentation](https://marlinfw.org/docs/gcode/M493.html) for more information.
|