Cura/resources/i18n/es/fdmprinter.json.po

msgid ""
msgstr ""
"Project-Id-Version: Uranium json setting files\n"
"Report-Msgid-Bugs-To: http://github.com/ultimaker/uranium\n"
"POT-Creation-Date: 2015-09-12 18:40+0000\n"
"PO-Revision-Date: 2015-06-30 00:58+0100\n"
"Last-Translator: \n"
"Language-Team: romain di vozzo <romaindivozzo@hotmail.com>\n"
"Language: es\n"
"MIME-Version: 1.0\n"
"Content-Type: text/plain; charset=UTF-8\n"
"Content-Transfer-Encoding: 8bit\n"
"X-Generator: Poedit 1.8.1\n"
"Plural-Forms: nplurals=2; plural=(n != 1);\n"
"X-Poedit-Bookmarks: 81,-1,-1,-1,-1,-1,-1,-1,-1,-1\n"

#: fdmprinter.json
msgctxt "resolution label"
msgid "Quality"
msgstr "Calidad"

#: fdmprinter.json
msgctxt "layer_height label"
msgid "Layer Height"
msgstr "Espesor de las Capas"

#: fdmprinter.json
msgctxt "layer_height description"
msgid ""
"The height of each layer, in mm. Normal quality prints are 0.1mm, high "
"quality is 0.06mm. You can go up to 0.25mm with an Ultimaker for very fast "
"prints at low quality. For most purposes, layer heights between 0.1 and "
"0.2mm give a good tradeoff of speed and surface finish."
msgstr ""
"El espesor de cada capa, en mm. Las impresiones de calidad normal son de "
"0.1mm, las impresiones de alta calidad son 0.06mm. Una maquina Ultimaker "
"puede imprimir capas de hasta 0.25mm para impresiones muy rápidas y de "
"calidad baja. Para la mayoría de las aplicaciones, un espesor de capas entre "
"0.1 y 0.2mm ofrece un buena compensación de la velocidad y del acabado "
"superficial."

#: fdmprinter.json
#, fuzzy
msgctxt "layer_height_0 label"
msgid "Initial Layer Height"
msgstr "Espesor de las Capas"

#: fdmprinter.json
#, fuzzy
msgctxt "layer_height_0 description"
msgid ""
"The layer height of the bottom layer. A thicker bottom layer makes sticking "
"to the bed easier."
msgstr ""
"El espesor de la capa inferior. Una capa inferior espesa facilita la "
"adherencia del objeto en la plataforma."

#: fdmprinter.json
#, fuzzy
msgctxt "line_width label"
msgid "Line Width"
msgstr "Anchura de las Lineas de la cáscara"

#: fdmprinter.json
msgctxt "line_width description"
msgid ""
"Width of a single line. Each line will be printed with this width in mind. "
"Generally the width of each line should correspond to the width of your "
"nozzle, but for the outer wall and top/bottom surface smaller line widths "
"may be chosen, for higher quality."
msgstr ""

#: fdmprinter.json
msgctxt "wall_line_width label"
msgid "Wall Line Width"
msgstr "Anchura de las Lineas de la cáscara"

#: fdmprinter.json
#, fuzzy
msgctxt "wall_line_width description"
msgid ""
"Width of a single shell line. Each line of the shell will be printed with "
"this width in mind."
msgstr ""
"La anchura de una sola linea de la cáscara. Cada linea de la cáscara será "
"impresa con esta anchura en memoria. "

#: fdmprinter.json
#, fuzzy
msgctxt "wall_line_width_0 label"
msgid "Outer Wall Line Width"
msgstr "Anchura de las Otras Lineas de la Pared"

#: fdmprinter.json
msgctxt "wall_line_width_0 description"
msgid ""
"Width of the outermost shell line. By printing a thinner outermost wall line "
"you can print higher details with a larger nozzle."
msgstr ""
"La anchura de la línea más externa de la cáscara. Imprimir una linea de capa "
"exterior más fina permite imprimir mas detalles, incluso con una boquilla "
"mas ancha."

#: fdmprinter.json
msgctxt "wall_line_width_x label"
msgid "Other Walls Line Width"
msgstr "Anchura de las Otras Lineas de la Pared"

#: fdmprinter.json
msgctxt "wall_line_width_x description"
msgid ""
"Width of a single shell line for all shell lines except the outermost one."
msgstr ""
"La anchura estándar de cada linea de la cáscara excepto la linea la más "
"externa de la pared."

#: fdmprinter.json
msgctxt "skirt_line_width label"
msgid "Skirt line width"
msgstr "Anchura de Cada Linea de la Falda."

#: fdmprinter.json
msgctxt "skirt_line_width description"
msgid "Width of a single skirt line."
msgstr "La anchura de cada linea de la falda."

#: fdmprinter.json
msgctxt "skin_line_width label"
msgid "Top/bottom line width"
msgstr "Anchura de Cada Linea de la Tapa y del Fondo"

#: fdmprinter.json
#, fuzzy
msgctxt "skin_line_width description"
msgid ""
"Width of a single top/bottom printed line, used to fill up the top/bottom "
"areas of a print."
msgstr ""
"La anchura de las lineas que componen la tapa y el fondo del objeto. Sirven "
"para llenar la tapa y el fondo del objeto."

#: fdmprinter.json
msgctxt "infill_line_width label"
msgid "Infill line width"
msgstr "Anchura de Cada Linea del Relleno"

#: fdmprinter.json
msgctxt "infill_line_width description"
msgid "Width of the inner infill printed lines."
msgstr "La anchura de las lineas que componen el relleno interior del objeto."

#: fdmprinter.json
msgctxt "support_line_width label"
msgid "Support line width"
msgstr "Anchura de las Lineas de Estructuras de Soporte"

#: fdmprinter.json
msgctxt "support_line_width description"
msgid "Width of the printed support structures lines."
msgstr "La anchura de las lineas que componen la estructura de soporte."

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_line_width label"
msgid "Support Roof line width"
msgstr "Anchura de las Lineas de Estructuras de Soporte"

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_line_width description"
msgid ""
"Width of a single support roof line, used to fill the top of the support."
msgstr ""
"La anchura de las lineas que componen la tapa y el fondo del objeto. Sirven "
"para llenar la tapa y el fondo del objeto."

#: fdmprinter.json
#, fuzzy
msgctxt "shell label"
msgid "Shell"
msgstr "Velocidad de Impresión de la Cáscara"

#: fdmprinter.json
msgctxt "shell_thickness label"
msgid "Shell Thickness"
msgstr "Espesor de la Cáscara"

#: fdmprinter.json
msgctxt "shell_thickness description"
msgid ""
"The thickness of the outside shell in the horizontal and vertical direction. "
"This is used in combination with the nozzle size to define the number of "
"perimeter lines and the thickness of those perimeter lines. This is also "
"used to define the number of solid top and bottom layers."
msgstr ""
"El espesor de la cáscara exterior en las direcciones horizontal y vertical. "
"Se utiliza en combinación con el tamaño del agujero de la boquilla para "
"definir el número de lineas del perímetro así que el espesor de las lineas "
"del perímetro. También, se utiliza para definir el número de capas de la "
"tapa tanto como el número de capas del fondo del objeto. "

#: fdmprinter.json
msgctxt "wall_thickness label"
msgid "Wall Thickness"
msgstr "Espesor de las Paredes"

#: fdmprinter.json
msgctxt "wall_thickness description"
msgid ""
"The thickness of the outside walls in the horizontal direction. This is used "
"in combination with the nozzle size to define the number of perimeter lines "
"and the thickness of those perimeter lines."
msgstr ""
"El espesor de la cáscara exterior en la dirección horizontal. Se utiliza en "
"combinación con el tamaño del agujero de la boquilla para definir el número "
"de lineas que componen el perímetro y el espesor de estas lineas "
"perimétricas."

#: fdmprinter.json
msgctxt "wall_line_count label"
msgid "Wall Line Count"
msgstr "Número de lineas de la pared."

#: fdmprinter.json
msgctxt "wall_line_count description"
msgid ""
"Number of shell lines. This these lines are called perimeter lines in other "
"tools and impact the strength and structural integrity of your print."
msgstr ""
"El número de lineas que componen la cáscara. Estas lineas se llaman lineas "
"perímetricas en otras herramientas y afectan la resistencia y la integridad "
"estructural de la impresión. "

#: fdmprinter.json
msgctxt "alternate_extra_perimeter label"
msgid "Alternate Extra Wall"
msgstr ""

#: fdmprinter.json
msgctxt "alternate_extra_perimeter description"
msgid ""
"Make an extra wall at every second layer, so that infill will be caught "
"between an extra wall above and one below. This results in a better cohesion "
"between infill and walls, but might have an impact on the surface quality."
msgstr ""

#: fdmprinter.json
msgctxt "top_bottom_thickness label"
msgid "Bottom/Top Thickness"
msgstr "Espesor del Fondo y de la Tapa"

#: fdmprinter.json
msgctxt "top_bottom_thickness description"
msgid ""
"This controls the thickness of the bottom and top layers, the amount of "
"solid layers put down is calculated by the layer thickness and this value. "
"Having this value a multiple of the layer thickness makes sense. And keep it "
"near your wall thickness to make an evenly strong part."
msgstr ""
"Este parámetro controla el espesor del fondo y de la tapa. La cantidad de "
"capas solidas aplicadas se calcula combinando el parámetro Espesor de Capas "
"y este valor. Se aconseja que este valor sea un múltiplo del valor elegido "
"en el parámetro Espesor de Capas. También, se aconseja elegir un valor más o "
"menos igual al parámetro Espesor de la Cáscara para conseguir objetos "
"resistentes. "

#: fdmprinter.json
msgctxt "top_thickness label"
msgid "Top Thickness"
msgstr "Espesor de la Tapa."

#: fdmprinter.json
msgctxt "top_thickness description"
msgid ""
"This controls the thickness of the top layers. The number of solid layers "
"printed is calculated from the layer thickness and this value. Having this "
"value be a multiple of the layer thickness makes sense. And keep it nearto "
"your wall thickness to make an evenly strong part."
msgstr ""
"Este parámetro controla el espesor de la tapa. El número de capas solidas se "
"calcula a partir del Espesor de Capas y este valor. Se aconseja que este "
"valor sea un múltiplo del Espesor de Capas. También, se aconseja que este "
"valor este mas o menos igual al parámetro Espesor de la Pared para conseguir "
"objetos resistentes."

#: fdmprinter.json
msgctxt "top_layers label"
msgid "Top Layers"
msgstr "Tapa"

#: fdmprinter.json
msgctxt "top_layers description"
msgid "This controls the amount of top layers."
msgstr "Este parámetro controla el número de capas que componen la tapa."

#: fdmprinter.json
msgctxt "bottom_thickness label"
msgid "Bottom Thickness"
msgstr "Espesor del fondo"

#: fdmprinter.json
msgctxt "bottom_thickness description"
msgid ""
"This controls the thickness of the bottom layers. The number of solid layers "
"printed is calculated from the layer thickness and this value. Having this "
"value be a multiple of the layer thickness makes sense. And keep it near to "
"your wall thickness to make an evenly strong part."
msgstr ""
"Este parámetro determina el espesor del fondo. El numéro de capas solidas se "
"calcula a partir del Espesor de Capas y este valor. Se aconseja que este "
"valor sea un múltiplo del Espesor de Capas. También, se aconseja que este "
"valor este mas o menos igual al parámetro Espesor de la Pared para conseguir "
"objetos resistentes."

#: fdmprinter.json
msgctxt "bottom_layers label"
msgid "Bottom Layers"
msgstr "Fondo"

#: fdmprinter.json
msgctxt "bottom_layers description"
msgid "This controls the amount of bottom layers."
msgstr "Este parámetro controla el número de capas que componen el fondo."

#: fdmprinter.json
#, fuzzy
msgctxt "remove_overlapping_walls_enabled label"
msgid "Remove Overlapping Wall Parts"
msgstr "Evitar Superponer Paredes."

#: fdmprinter.json
#, fuzzy
msgctxt "remove_overlapping_walls_enabled description"
msgid ""
"Remove parts of a wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."
msgstr ""
"Este parámetro suprime partes de un objeto dónde varias capas se superponen "
"en una misma pared, lo que resultaría en una extrusión excesiva de "
"filamento. Estas superposiciones ocurren en las partes finas de un modelo 3D "
"y en sus esquinas agudas."

#: fdmprinter.json
#, fuzzy
msgctxt "remove_overlapping_walls_0_enabled label"
msgid "Remove Overlapping Outer Wall Parts"
msgstr "Evitar Superponer Paredes."

#: fdmprinter.json
#, fuzzy
msgctxt "remove_overlapping_walls_0_enabled description"
msgid ""
"Remove parts of an outer wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."
msgstr ""
"Este parámetro suprime partes de un objeto dónde varias capas se superponen "
"en una misma pared, lo que resultaría en una extrusión excesiva de "
"filamento. Estas superposiciones ocurren en las partes finas de un modelo 3D "
"y en sus esquinas agudas."

#: fdmprinter.json
#, fuzzy
msgctxt "remove_overlapping_walls_x_enabled label"
msgid "Remove Overlapping Other Wall Parts"
msgstr "Evitar Superponer Paredes."

#: fdmprinter.json
#, fuzzy
msgctxt "remove_overlapping_walls_x_enabled description"
msgid ""
"Remove parts of an inner wall which share an overlap which would result in "
"overextrusion in some places. These overlaps occur in thin pieces in a model "
"and sharp corners."
msgstr ""
"Este parámetro suprime partes de un objeto dónde varias capas se superponen "
"en una misma pared, lo que resultaría en una extrusión excesiva de "
"filamento. Estas superposiciones ocurren en las partes finas de un modelo 3D "
"y en sus esquinas agudas."

#: fdmprinter.json
msgctxt "travel_compensate_overlapping_walls_enabled label"
msgid "Compensate Wall Overlaps"
msgstr ""

#: fdmprinter.json
msgctxt "travel_compensate_overlapping_walls_enabled description"
msgid ""
"Compensate the flow for parts of a wall being laid down where there already "
"is a piece of a wall. These overlaps occur in thin pieces in a model. Gcode "
"generation might be slowed down considerably."
msgstr ""

#: fdmprinter.json
msgctxt "fill_perimeter_gaps label"
msgid "Fill Gaps Between Walls"
msgstr ""

#: fdmprinter.json
msgctxt "fill_perimeter_gaps description"
msgid ""
"Fill the gaps created by walls where they would otherwise be overlapping. "
"This will also fill thin walls. Optionally only the gaps occurring within "
"the top and bottom skin can be filled."
msgstr ""

#: fdmprinter.json
msgctxt "fill_perimeter_gaps option nowhere"
msgid "Nowhere"
msgstr ""

#: fdmprinter.json
msgctxt "fill_perimeter_gaps option everywhere"
msgid "Everywhere"
msgstr ""

#: fdmprinter.json
msgctxt "fill_perimeter_gaps option skin"
msgid "Skin"
msgstr ""

#: fdmprinter.json
msgctxt "top_bottom_pattern label"
msgid "Bottom/Top Pattern"
msgstr "Patrón de la Tapa y del Fondo"

#: fdmprinter.json
msgctxt "top_bottom_pattern description"
msgid ""
"Pattern of the top/bottom solid fill. This normally is done with lines to "
"get the best possible finish, but in some cases a concentric fill gives a "
"nicer end result."
msgstr ""
"El patrón de relleno de la tapa y del fondo. Se suele imprimir con lineas "
"para conseguir el mejor acabado posible pero, en algunos casos, un relleno "
"concéntrico permite conseguir un mejor acabado."

#: fdmprinter.json
msgctxt "top_bottom_pattern option lines"
msgid "Lines"
msgstr ""

#: fdmprinter.json
msgctxt "top_bottom_pattern option concentric"
msgid "Concentric"
msgstr ""

#: fdmprinter.json
msgctxt "top_bottom_pattern option zigzag"
msgid "Zig Zag"
msgstr ""

#: fdmprinter.json
msgctxt "skin_no_small_gaps_heuristic label"
msgid "Ingore small Z gaps"
msgstr ""

#: fdmprinter.json
msgctxt "skin_no_small_gaps_heuristic description"
msgid ""
"When the model has small vertical gaps about 5% extra computation time can "
"be spent on generating top and bottom skin in these narrow spaces. In such a "
"case set this setting to false."
msgstr ""

#: fdmprinter.json
msgctxt "skin_alternate_rotation label"
msgid "Alternate Skin Rotation"
msgstr ""

#: fdmprinter.json
msgctxt "skin_alternate_rotation description"
msgid ""
"Alternate between diagonal skin fill and horizontal + vertical skin fill. "
"Although the diagonal directions can print quicker, this option can improve "
"on the printing quality by reducing the pillowing effect."
msgstr ""

#: fdmprinter.json
msgctxt "skin_outline_count label"
msgid "Skin Perimeter Line Count"
msgstr "Número de Lineas de la Piel"

#: fdmprinter.json
msgctxt "skin_outline_count description"
msgid ""
"Number of lines around skin regions. Using one or two skin perimeter lines "
"can greatly improve on roofs which would start in the middle of infill cells."
msgstr ""
"El número de lineas perimétricas alrededor de las zonas de piel. Utilizar 1 "
"o 2 lineas perimétricas de piel puede mejorar la calidad de impresión de "
"tapas que empezarían en el medio de células rellenas."

#: fdmprinter.json
msgctxt "xy_offset label"
msgid "Horizontal expansion"
msgstr "Expansión Horizontal"

#: fdmprinter.json
msgctxt "xy_offset description"
msgid ""
"Amount of offset applied all polygons in each layer. Positive values can "
"compensate for too big holes; negative values can compensate for too small "
"holes."
msgstr ""
"La cantidad de desplazamiento aplicada a cada polígono en cada capa. Un "
"valor positivo compensa agujeros grandes; un valor negativo compensa "
"agujeros más pequeños."

#: fdmprinter.json
msgctxt "z_seam_type label"
msgid "Z Seam Alignment"
msgstr ""

#: fdmprinter.json
msgctxt "z_seam_type description"
msgid ""
"Starting point of each part in a layer. When parts in consecutive layers "
"start at the same point a vertical seam may show on the print. When aligning "
"these at the back, the seam is easiest to remove. When placed randomly the "
"inaccuracies at the part start will be less noticable. When taking the "
"shortest path the print will be more quick."
msgstr ""

#: fdmprinter.json
msgctxt "z_seam_type option back"
msgid "Back"
msgstr ""

#: fdmprinter.json
msgctxt "z_seam_type option shortest"
msgid "Shortest"
msgstr ""

#: fdmprinter.json
msgctxt "z_seam_type option random"
msgid "Random"
msgstr ""

#: fdmprinter.json
msgctxt "infill label"
msgid "Infill"
msgstr "Relleno"

#: fdmprinter.json
#, fuzzy
msgctxt "infill_sparse_density label"
msgid "Infill Density"
msgstr "Densidad del Relleno"

#: fdmprinter.json
#, fuzzy
msgctxt "infill_sparse_density description"
msgid ""
"This controls how densely filled the insides of your print will be. For a "
"solid part use 100%, for an hollow part use 0%. A value around 20% is "
"usually enough. This won't affect the outside of the print and only adjusts "
"how strong the part becomes."
msgstr ""
"Este parámetro controla la cantidad de relleno del objeto. Para un objeto "
"solido, se utiliza 100%, para un objeto vacío utilizar 0%. Un valor próximo "
"a 20% suele ser suficiente. Este parámetro no afectará la piel del objeto y "
"solo ajustará la resistencia del objeto. "

#: fdmprinter.json
msgctxt "infill_line_distance label"
msgid "Line distance"
msgstr "Distancia entre las Lineas del Relleno"

#: fdmprinter.json
msgctxt "infill_line_distance description"
msgid "Distance between the printed infill lines."
msgstr "La distancia entre las lineas de relleno del objeto."

#: fdmprinter.json
#, fuzzy
msgctxt "infill_pattern label"
msgid "Infill Pattern"
msgstr "Patrón del Relleno"

# Needs to be completed later!
#: fdmprinter.json
#, fuzzy
msgctxt "infill_pattern description"
msgid ""
"Cura defaults to switching between grid and line infill. But with this "
"setting visible you can control this yourself. The line infill swaps "
"direction on alternate layers of infill, while the grid prints the full "
"cross-hatching on each layer of infill."
msgstr ""
"Por defecto, Cura no ofrece la opción de elegir entre rejilla y relleno. "
"Ahora que este parámetro es visible, el usuario de Cura lo puede cambiar."

#: fdmprinter.json
msgctxt "infill_pattern option grid"
msgid "Grid"
msgstr ""

#: fdmprinter.json
msgctxt "infill_pattern option lines"
msgid "Lines"
msgstr ""

#: fdmprinter.json
msgctxt "infill_pattern option concentric"
msgid "Concentric"
msgstr ""

#: fdmprinter.json
msgctxt "infill_pattern option zigzag"
msgid "Zig Zag"
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "infill_overlap label"
msgid "Infill Overlap"
msgstr "Superposición de Relleno"

#: fdmprinter.json
#, fuzzy
msgctxt "infill_overlap description"
msgid ""
"The amount of overlap between the infill and the walls. A slight overlap "
"allows the walls to connect firmly to the infill."
msgstr ""
"La cantidad de superposición entre el relleno y la paredes. Una "
"superposición ligera permite que las paredes se conecten firmemente al "
"relleno."

#: fdmprinter.json
#, fuzzy
msgctxt "infill_wipe_dist label"
msgid "Infill Wipe Distance"
msgstr "Anchura de Cada Linea del Relleno"

#: fdmprinter.json
msgctxt "infill_wipe_dist description"
msgid ""
"Distance of a travel move inserted after every infill line, to make the "
"infill stick to the walls better. This option is imilar to infill overlap, "
"but without extrusion and only on one end of the infill line."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "infill_sparse_thickness label"
msgid "Infill Thickness"
msgstr "Espesor del Relleno"

#: fdmprinter.json
#, fuzzy
msgctxt "infill_sparse_thickness description"
msgid ""
"The thickness of the sparse infill. This is rounded to a multiple of the "
"layerheight and used to print the sparse-infill in fewer, thicker layers to "
"save printing time."
msgstr ""
"El espesor del relleno escaso. Este parámetro se redondea a un múltiplo del "
"espesor de capa y se utiliza para imprimir el relleno escaso en menos capas "
"para reducir la duración de la impresión."

#: fdmprinter.json
#, fuzzy
msgctxt "infill_sparse_combine label"
msgid "Infill Layers"
msgstr "Relleno de Capas"

#: fdmprinter.json
#, fuzzy
msgctxt "infill_sparse_combine description"
msgid "Amount of layers that are combined together to form sparse infill."
msgstr "La cantidad de capas combinadas parar formar el relleno escaso."

#: fdmprinter.json
#, fuzzy
msgctxt "infill_before_walls label"
msgid "Infill Before Walls"
msgstr "Relleno de Capas"

#: fdmprinter.json
msgctxt "infill_before_walls description"
msgid ""
"Print the infill before printing the walls. Printing the walls first may "
"lead to more accurate walls, but overhangs print worse. Printing the infill "
"first leads to sturdier walls, but the infill pattern might sometimes show "
"through the surface."
msgstr ""

#: fdmprinter.json
msgctxt "material label"
msgid "Material"
msgstr "Material"

#: fdmprinter.json
msgctxt "material_print_temperature label"
msgid "Printing Temperature"
msgstr "Temperatura de la Impresión "

#: fdmprinter.json
msgctxt "material_print_temperature description"
msgid ""
"The temperature used for printing. Set at 0 to pre-heat yourself. For PLA a "
"value of 210C is usually used.\n"
"For ABS a value of 230C or higher is required."
msgstr ""
"La temperatura utilizada para imprimir. Poner el valor a 0 para precalentar "
"la boquilla manualmente. Generalmente, el PLA se imprime a 210C.\n"
"El ABS se imprime a una temperatura mínima de 230C. "

#: fdmprinter.json
msgctxt "material_bed_temperature label"
msgid "Bed Temperature"
msgstr "Temperatura de la Plataforma"

#: fdmprinter.json
msgctxt "material_bed_temperature description"
msgid ""
"The temperature used for the heated printer bed. Set at 0 to pre-heat it "
"yourself."
msgstr ""
"La temperatura utilizada para la plataforma caliente. Poner el valor a 0 "
"para precalentar manualmente."

#: fdmprinter.json
msgctxt "material_diameter label"
msgid "Diameter"
msgstr "Diámetro"

#: fdmprinter.json
msgctxt "material_diameter description"
msgid ""
"The diameter of your filament needs to be measured as accurately as "
"possible.\n"
"If you cannot measure this value you will have to calibrate it, a higher "
"number means less extrusion, a smaller number generates more extrusion."
msgstr ""
"Se recomienda medir el diámetro del filamento precisamente.\n"
"Si no se puede medir, hay que calibrarlo. Un valor alto significa menos "
"extrusión, un valor más bajo genera mas extrusión. "

#: fdmprinter.json
msgctxt "material_flow label"
msgid "Flow"
msgstr "Flujo"

#: fdmprinter.json
msgctxt "material_flow description"
msgid ""
"Flow compensation: the amount of material extruded is multiplied by this "
"value."
msgstr ""
"Compensación de flujo: La cantidad de material extrusionado se multiplica "
"por este valor."

#: fdmprinter.json
msgctxt "retraction_enable label"
msgid "Enable Retraction"
msgstr "Activar Retracción"

#: fdmprinter.json
msgctxt "retraction_enable description"
msgid ""
"Retract the filament when the nozzle is moving over a non-printed area. "
"Details about the retraction can be configured in the advanced tab."
msgstr ""
"Retrae el filamento cuando la boquilla se mueve sobre una zona non-impresa. "
"Mas opciones tocante a la retracción son disponibles en la pestaña avanzada."

#: fdmprinter.json
msgctxt "retraction_amount label"
msgid "Retraction Distance"
msgstr "Distancia de Retracción"

#: fdmprinter.json
msgctxt "retraction_amount description"
msgid ""
"The amount of retraction: Set at 0 for no retraction at all. A value of "
"4.5mm seems to generate good results for 3mm filament in Bowden-tube fed "
"printers."
msgstr ""
"La longitud de retracción. Poner el valor a 0 si no se necesita retracción. "
"Un valor de 4.5mm parece generar buenos resultados para filamentos de 3mm "
"cargados en impresoras equipadas con un tubo de tipo \"Bowden\"."

#: fdmprinter.json
msgctxt "retraction_speed label"
msgid "Retraction Speed"
msgstr "Velocidad de la Retracción"

#: fdmprinter.json
msgctxt "retraction_speed description"
msgid ""
"The speed at which the filament is retracted. A higher retraction speed "
"works better, but a very high retraction speed can lead to filament grinding."
msgstr ""
"La velocidad a la que el filamento se retrae. Un valor de retracción mas "
"alto funciona mejor, pero un valor de retracción muy alto puede llegar a "
"moler el filamento."

# ? same as previous ?
#: fdmprinter.json
msgctxt "retraction_retract_speed label"
msgid "Retraction Retract Speed"
msgstr "? same as previous ?"

# ? same as previous ?
#: fdmprinter.json
msgctxt "retraction_retract_speed description"
msgid ""
"The speed at which the filament is retracted. A higher retraction speed "
"works better, but a very high retraction speed can lead to filament grinding."
msgstr "? same as previous ?"

#: fdmprinter.json
msgctxt "retraction_prime_speed label"
msgid "Retraction Prime Speed"
msgstr "Velocidad de Retracción Inicial (primera)"

#: fdmprinter.json
msgctxt "retraction_prime_speed description"
msgid "The speed at which the filament is pushed back after retraction."
msgstr ""
"La velocidad a la que el filamento se retrocede en la boquilla justo después "
"de la retracción."

#: fdmprinter.json
#, fuzzy
msgctxt "retraction_extra_prime_amount label"
msgid "Retraction Extra Prime Amount"
msgstr "Velocidad de Retracción Inicial (primera)"

#: fdmprinter.json
msgctxt "retraction_extra_prime_amount description"
msgid ""
"The amount of material extruded after unretracting. During a retracted "
"travel material might get lost and so we need to compensate for this."
msgstr ""

#: fdmprinter.json
msgctxt "retraction_min_travel label"
msgid "Retraction Minimum Travel"
msgstr "Viaje Mínimo para la Retracción"

#: fdmprinter.json
msgctxt "retraction_min_travel description"
msgid ""
"The minimum distance of travel needed for a retraction to happen at all. "
"This helps ensure you do not get a lot of retractions in a small area."
msgstr ""
"La distancia mínima de viaje que se necesita para que ocurriera la "
"retracción. Este parámetro permite evitar un exceso de retracción sobre "
"zonas chicas."

#: fdmprinter.json
#, fuzzy
msgctxt "retraction_count_max label"
msgid "Maximal Retraction Count"
msgstr "Activar Retracción"

#: fdmprinter.json
#, fuzzy
msgctxt "retraction_count_max description"
msgid ""
"This settings limits the number of retractions occuring within the Minimal "
"Extrusion Distance Window. Further retractions within this window will be "
"ignored. This avoids retracting repeatedly on the same piece of filament as "
"that can flatten the filament and cause grinding issues."
msgstr ""
"La cantidad mínima de extrusión que tiene que ocurrir entre 2 retracciones. "
"Si una retracción ocurre antes de que este mínimo este alcanzado, se "
"ignorará. Este parámetro evita repetir muchas retracciones sobre el  mismo "
"segmento de filamento y evita consecuentemente de causar aplastamiento y "
"molienda.  "

#: fdmprinter.json
#, fuzzy
msgctxt "retraction_extrusion_window label"
msgid "Minimal Extrusion Distance Window"
msgstr "Extrusión Mínima Antes de la Retracción "

#: fdmprinter.json
msgctxt "retraction_extrusion_window description"
msgid ""
"The window in which the Maximal Retraction Count is enforced. This window "
"should be approximately the size of the Retraction distance, so that "
"effectively the number of times a retraction passes the same patch of "
"material is limited."
msgstr ""

#: fdmprinter.json
msgctxt "retraction_hop label"
msgid "Z Hop when Retracting"
msgstr "Salto del Eje Z Cuando Retrae"

#: fdmprinter.json
msgctxt "retraction_hop description"
msgid ""
"Whenever a retraction is done, the head is lifted by this amount to travel "
"over the print. A value of 0.075 works well. This feature has a lot of "
"positive effect on delta towers."
msgstr ""
"Cada vez que retrae el filamento, el cabezal de impresión se levanta de esta "
"altura para viajar encima del objeto. Un valor de 0.075 funciona bien. Esta "
"característica suele tener muchos efectos positivos sobre las torres delta."

#: fdmprinter.json
msgctxt "speed label"
msgid "Speed"
msgstr "Velocidad"

#: fdmprinter.json
msgctxt "speed_print label"
msgid "Print Speed"
msgstr "Velocidad de la Impresión"

#: fdmprinter.json
msgctxt "speed_print description"
msgid ""
"The speed at which printing happens. A well-adjusted Ultimaker can reach "
"150mm/s, but for good quality prints you will want to print slower. Printing "
"speed depends on a lot of factors, so you will need to experiment with "
"optimal settings for this."
msgstr ""
"La velocidad a la que se hace la impresión. Una Ultimaker bien ajustada "
"puede alcanzar 150mm/s pero, para impresiones de buena calidad, se suele "
"imprimir más lento. La velocidad de impresión depende de muchos factores, "
"por lo que tendrá que experimentar con los ajustes óptimos."

#: fdmprinter.json
msgctxt "speed_infill label"
msgid "Infill Speed"
msgstr "Velocidad del Relleno"

#: fdmprinter.json
msgctxt "speed_infill description"
msgid ""
"The speed at which infill parts are printed. Printing the infill faster can "
"greatly reduce printing time, but this can negatively affect print quality."
msgstr ""
"La velocidad a la que el relleno se imprime. Imprimir el relleno más rápido "
"puede reducir mucho la duración de la impresión pero puede afectar "
"negativamente la calidad de la impresión."

#: fdmprinter.json
msgctxt "speed_wall label"
msgid "Shell Speed"
msgstr "Velocidad de Impresión de la Cáscara"

#: fdmprinter.json
msgctxt "speed_wall description"
msgid ""
"The speed at which shell is printed. Printing the outer shell at a lower "
"speed improves the final skin quality."
msgstr ""
"La velocidad a la cual se imprime la cáscara del objeto. Imprimir la cáscara "
"del objeto a una velocidad más lenta mejora el acabado de la piel."

#: fdmprinter.json
msgctxt "speed_wall_0 label"
msgid "Outer Shell Speed"
msgstr "Velocidad de Impresión de la Parte Externa de la Cáscara"

#: fdmprinter.json
msgctxt "speed_wall_0 description"
msgid ""
"The speed at which outer shell is printed. Printing the outer shell at a "
"lower speed improves the final skin quality. However, having a large "
"difference between the inner shell speed and the outer shell speed will "
"effect quality in a negative way."
msgstr ""
"La velocidad a la que se imprime la cáscara exterior del objeto. Imprimir la "
"cáscara exterior del objeto más lento mejora el acabado de la piel."

#: fdmprinter.json
msgctxt "speed_wall_x label"
msgid "Inner Shell Speed"
msgstr "Velocidad de Impresión de la Parte Interna de la Cáscara"

#: fdmprinter.json
msgctxt "speed_wall_x description"
msgid ""
"The speed at which  all inner shells are printed. Printing the inner shell "
"fasster than the outer shell will reduce printing time. It is good to set "
"this in between the outer shell speed and the infill speed."
msgstr ""
"La velocidad a la que la cáscara interior se imprime. Imprimir la cáscara "
"interior más rápido que la cáscara exterior puede reducir mucho la duración "
"de la impresión. Se recomienda poner un valor entre la velocidad de "
"impresión de la cáscara exterior y la velocidad de impresión del relleno."

#: fdmprinter.json
msgctxt "speed_topbottom label"
msgid "Top/Bottom Speed"
msgstr "Velocidad de Impresión de las Tapa y del Fondo"

#: fdmprinter.json
msgctxt "speed_topbottom description"
msgid ""
"Speed at which top/bottom parts are printed. Printing the top/bottom faster "
"can greatly reduce printing time, but this can negatively affect print "
"quality."
msgstr ""
"La velocidad a la que se imprimen la tapa y el fondo del objeto. Imprimir la "
"tapa y el fondo más rápido puede reducir mucho la duración de la impresión "
"pero puede afectar negativamente la calidad de la impresión."

#: fdmprinter.json
msgctxt "speed_support label"
msgid "Support Speed"
msgstr "Velocidad de Impresión del Estructuras de Soporte"

#: fdmprinter.json
msgctxt "speed_support description"
msgid ""
"The speed at which exterior support is printed. Printing exterior supports "
"at higher speeds can greatly improve printing time. And the surface quality "
"of exterior support is usually not important, so higher speeds can be used."
msgstr ""
"La velocidad a la que se imprime las estructuras de soporte. Imprimir las "
"estructuras de soporte más rápido puede reducir mucho la duración de "
"impresión. También, la calidad de la superficie exterior de la estructuras "
"de soporte no importa mucho, así que imprimir más rápido es posible."

#: fdmprinter.json
#, fuzzy
msgctxt "speed_support_lines label"
msgid "Support Wall Speed"
msgstr "Velocidad de Impresión del Estructuras de Soporte"

#: fdmprinter.json
#, fuzzy
msgctxt "speed_support_lines description"
msgid ""
"The speed at which the walls of exterior support are printed. Printing the "
"walls at higher speeds can improve on the overall duration. "
msgstr ""
"La velocidad a la cual se imprime la cáscara del objeto. Imprimir la cáscara "
"del objeto a una velocidad más lenta mejora el acabado de la piel."

#: fdmprinter.json
#, fuzzy
msgctxt "speed_support_roof label"
msgid "Support Roof Speed"
msgstr "Velocidad de Impresión del Estructuras de Soporte"

#: fdmprinter.json
#, fuzzy
msgctxt "speed_support_roof description"
msgid ""
"The speed at which the roofs of exterior support are printed. Printing the "
"support roof at lower speeds can improve on overhang quality. "
msgstr ""
"La velocidad a la cual se imprime la cáscara del objeto. Imprimir la cáscara "
"del objeto a una velocidad más lenta mejora el acabado de la piel."

#: fdmprinter.json
msgctxt "speed_travel label"
msgid "Travel Speed"
msgstr "Velocidad de Viajes sin Imprimir"

#: fdmprinter.json
msgctxt "speed_travel description"
msgid ""
"The speed at which travel moves are done. A well-built Ultimaker can reach "
"speeds of 250mm/s. But some machines might have misaligned layers then."
msgstr ""
"La velocidad a la que el cabezal de impresión viaja cuando no imprime. Una "
"Ultimaker bien construida puede alcanzar la velocidad de 250mm/s."

#: fdmprinter.json
msgctxt "speed_layer_0 label"
msgid "Bottom Layer Speed"
msgstr "Velocidad de Impresión del Fondo"

#: fdmprinter.json
msgctxt "speed_layer_0 description"
msgid ""
"The print speed for the bottom layer: You want to print the first layer "
"slower so it sticks to the printer bed better."
msgstr ""
"La velocidad a la que se imprime el fondo del objeto: Imprimir esta primera "
"capa más lento mejora muchísimo la adherencia del objeto durante la "
"impresión."

#: fdmprinter.json
msgctxt "skirt_speed label"
msgid "Skirt Speed"
msgstr "Velocidad de Impresión de la Falda"

#: fdmprinter.json
msgctxt "skirt_speed description"
msgid ""
"The speed at which the skirt and brim are printed. Normally this is done at "
"the initial layer speed. But sometimes you want to print the skirt at a "
"different speed."
msgstr ""
"La velocidad a la que se imprimen la falda y la visera. Se suele imprimir a "
"la misma velocidad de impresión que la del fondo pero se puede imprimir a "
"una velocidad diferente cuando necesario.  "

#: fdmprinter.json
msgctxt "speed_slowdown_layers label"
msgid "Amount of Slower Layers"
msgstr "Cantidad de Capas Lentas"

#: fdmprinter.json
msgctxt "speed_slowdown_layers description"
msgid ""
"The first few layers are printed slower then the rest of the object, this to "
"get better adhesion to the printer bed and improve the overall success rate "
"of prints. The speed is gradually increased over these layers. 4 layers of "
"speed-up is generally right for most materials and printers."
msgstr ""
"Las primeras capas se imprimen más lento que el resto del objeto para "
"conseguir mas adherencia a la plataforma y para mejorar la tasa de éxito de "
"las impresiones. La velocidad se aumenta gradualmente a lo largo de la "
"impresión de estas capas. 4 capas de aceleración suelen funcionar bien para "
"la mayoría de los materiales y impresoras."

#: fdmprinter.json
#, fuzzy
msgctxt "travel label"
msgid "Travel"
msgstr "Velocidad de Viajes sin Imprimir"

#: fdmprinter.json
msgctxt "retraction_combing label"
msgid "Enable Combing"
msgstr "Activar la Peinada"

#: fdmprinter.json
msgctxt "retraction_combing description"
msgid ""
"Combing keeps the head within the interior of the print whenever possible "
"when traveling from one part of the print to another, and does not use "
"retraction. If combing is disabled the printer head moves straight from the "
"start point to the end point and it will always retract."
msgstr ""
"La peinada mantiene el cabezal de impresión a dentro de la superficie de "
"impresión siempre que sea posible cuando viaja de una parte del objeto a "
"otra, sin utilizar la función de retracción. Si la peinada esta "
"deshabilitada, el cabezal de impresión viaja directamente del punto de "
"partida hasta el punto final y retrae siempre el filamento."

#: fdmprinter.json
msgctxt "travel_avoid_other_parts label"
msgid "Avoid Printed Parts"
msgstr ""

#: fdmprinter.json
msgctxt "travel_avoid_other_parts description"
msgid "Avoid other parts when traveling between parts."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "travel_avoid_distance label"
msgid "Avoid Distance"
msgstr "Distancia de Articulación"

#: fdmprinter.json
msgctxt "travel_avoid_distance description"
msgid "The distance to stay clear of parts which are avoided during travel."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "coasting_enable label"
msgid "Enable Coasting"
msgstr "Activar la Peinada"

#: fdmprinter.json
msgctxt "coasting_enable description"
msgid ""
"Coasting replaces the last part of an extrusion path with a travel path. The "
"oozed material is used to lay down the last piece of the extrusion path in "
"order to reduce stringing."
msgstr ""

#: fdmprinter.json
msgctxt "coasting_volume label"
msgid "Coasting Volume"
msgstr ""

#: fdmprinter.json
msgctxt "coasting_volume description"
msgid ""
"The volume otherwise oozed. This value should generally be close to the "
"nozzle diameter cubed."
msgstr ""

#: fdmprinter.json
msgctxt "coasting_volume_retract label"
msgid "Retract-Coasting Volume"
msgstr ""

#: fdmprinter.json
msgctxt "coasting_volume_retract description"
msgid "The volume otherwise oozed in a travel move with retraction."
msgstr ""

#: fdmprinter.json
msgctxt "coasting_volume_move label"
msgid "Move-Coasting Volume"
msgstr ""

#: fdmprinter.json
msgctxt "coasting_volume_move description"
msgid "The volume otherwise oozed in a travel move without retraction."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "coasting_min_volume label"
msgid "Minimal Volume Before Coasting"
msgstr "Extrusión Mínima Antes de la Retracción "

#: fdmprinter.json
msgctxt "coasting_min_volume description"
msgid ""
"The least volume an extrusion path should have to coast the full amount. For "
"smaller extrusion paths, less pressure has been built up in the bowden tube "
"and so the coasted volume is scaled linearly."
msgstr ""

#: fdmprinter.json
msgctxt "coasting_min_volume_retract label"
msgid "Min Volume Retract-Coasting"
msgstr ""

#: fdmprinter.json
msgctxt "coasting_min_volume_retract description"
msgid ""
"The minimal volume an extrusion path must have in order to coast the full "
"amount before doing a retraction."
msgstr ""

#: fdmprinter.json
msgctxt "coasting_min_volume_move label"
msgid "Min Volume Move-Coasting"
msgstr ""

#: fdmprinter.json
msgctxt "coasting_min_volume_move description"
msgid ""
"The minimal volume an extrusion path must have in order to coast the full "
"amount before doing a travel move without retraction."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "coasting_speed label"
msgid "Coasting Speed"
msgstr "Velocidad del Ventilador"

#: fdmprinter.json
msgctxt "coasting_speed description"
msgid ""
"The speed by which to move during coasting, relative to the speed of the "
"extrusion path. A value slightly under 100% is advised, since during the "
"coasting move, the pressure in the bowden tube drops."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "coasting_speed_retract label"
msgid "Retract-Coasting Speed"
msgstr "Velocidad de la Retracción"

#: fdmprinter.json
msgctxt "coasting_speed_retract description"
msgid ""
"The speed by which to move during coasting before a retraction, relative to "
"the speed of the extrusion path."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "coasting_speed_move label"
msgid "Move-Coasting Speed"
msgstr "Velocidad de la Retracción"

#: fdmprinter.json
msgctxt "coasting_speed_move description"
msgid ""
"The speed by which to move during coasting before a travel move without "
"retraction, relative to the speed of the extrusion path."
msgstr ""

#: fdmprinter.json
msgctxt "cooling label"
msgid "Cooling"
msgstr "Enfriamiento "

#: fdmprinter.json
msgctxt "cool_fan_enabled label"
msgid "Enable Cooling Fan"
msgstr "Activar los Ventiladores"

# Unclear
#: fdmprinter.json
msgctxt "cool_fan_enabled description"
msgid ""
"Enable the cooling fan during the print. The extra cooling from the cooling "
"fan helps parts with small cross sections that print each layer quickly."
msgstr ""
"Activa los ventiladores durante la impresión. El suplemento de enfriamiento "
"de los ventiladores ayuda los objetos con pequeñas secciones transversales "
"que imprimen cada capa rápido."

#: fdmprinter.json
msgctxt "cool_fan_speed label"
msgid "Fan Speed"
msgstr "Velocidad del Ventilador"

#: fdmprinter.json
msgctxt "cool_fan_speed description"
msgid "Fan speed used for the print cooling fan on the printer head."
msgstr ""
"La velocidad del ventilador ubicado sobre el cabezal de impresión utilizado "
"para enfriar el objeto mientras se esta imprimiendo."

#: fdmprinter.json
msgctxt "cool_fan_speed_min label"
msgid "Minimum Fan Speed"
msgstr "Velocidad Mínima del Ventilador"

# error ? similar to the next explanation
#: fdmprinter.json
msgctxt "cool_fan_speed_min description"
msgid ""
"Normally the fan runs at the minimum fan speed. If the layer is slowed down "
"due to minimum layer time, the fan speed adjusts between minimum and maximum "
"fan speed."
msgstr ""
"Normalmente, el ventilador funciona a su velocidad mínima. Si la impresión "
"de la capa se hace mas despacio por culpa del parámetro de duración mínima "
"de impresión de una capa, la velocidad del ventilador se ajusta entre el "
"mínimum y el máximum del parámetro de velocidad del ventilador."

#: fdmprinter.json
msgctxt "cool_fan_speed_max label"
msgid "Maximum Fan Speed"
msgstr "Velocidad Máxima del Ventilador"

# error ? similar to the previous explanation ?
#: fdmprinter.json
msgctxt "cool_fan_speed_max description"
msgid ""
"Normally the fan runs at the minimum fan speed. If the layer is slowed down "
"due to minimum layer time, the fan speed adjusts between minimum and maximum "
"fan speed."
msgstr ""
"Normalmente, el ventilador funciona a su velocidad mínima. Si la impresión "
"de la capa se hace mas despacio por culpa del parámetro de duración mínima "
"de impresión de una capa, la velocidad del ventilador se ajusta entre el "
"mínimum y el máximum del parámetro de velocidad del ventilador."

#: fdmprinter.json
msgctxt "cool_fan_full_at_height label"
msgid "Fan Full on at Height"
msgstr "Altura de Velocidad Máxima del Ventilador"

#: fdmprinter.json
msgctxt "cool_fan_full_at_height description"
msgid ""
"The height at which the fan is turned on completely. For the layers below "
"this the fan speed is scaled linearly with the fan off for the first layer."
msgstr ""
"La altura del objeto a la que el ventilador gira a su velocidad máxima. "
"Durante la impresión de la primera capa, el ventilador esta apagado. Después "
"de la impresión de la primera capa, la velocidad del ventilador aumenta "
"linearmente hasta su velocidad máxima."

#: fdmprinter.json
msgctxt "cool_fan_full_layer label"
msgid "Fan Full on at Layer"
msgstr "Capa de Velocidad Máxima del Ventilador"

#: fdmprinter.json
msgctxt "cool_fan_full_layer description"
msgid ""
"The layer number at which the fan is turned on completely. For the layers "
"below this the fan speed is scaled linearly with the fan off for the first "
"layer."
msgstr ""
"El número de capa a la que el ventilador gira a su velocidad máxima. Para la "
"impresión de las capas previas, la velocidad del ventilador cambia "
"linearmente cuando se acaba la impresión de la primera capa. Durante la "
"impresión de la primera capa, el ventilador esta apagado."

#: fdmprinter.json
msgctxt "cool_min_layer_time label"
msgid "Minimal Layer Time"
msgstr "Duración Mínima de Impresión de una Capa"

#: fdmprinter.json
msgctxt "cool_min_layer_time description"
msgid ""
"The minimum time spent in a layer: Gives the layer time to cool down before "
"the next one is put on top. If a layer would print in less time, then the "
"printer will slow down to make sure it has spent at least this many seconds "
"printing the layer."
msgstr ""
"La duración mínima de impresión de una capa: Le da a la capa el tiempo de "
"enfriarse antes de que se imprime la capa siguiente. Si se imprime una capa "
"en menos tiempo, la impresora ralentiza para asegurarse que ha pasado por lo "
"menos esta cantidad de segundos imprimiendo la capa."

#: fdmprinter.json
msgctxt "cool_min_layer_time_fan_speed_max label"
msgid "Minimal Layer Time Full Fan Speed"
msgstr "Duración mínima de ventilación máxima"

#: fdmprinter.json
#, fuzzy
msgctxt "cool_min_layer_time_fan_speed_max description"
msgid ""
"The minimum time spent in a layer which will cause the fan to be at maximum "
"speed. The fan speed increases linearly from minimal fan speed for layers "
"taking minimal layer time to maximum fan speed for layers taking the time "
"specified here."
msgstr ""
"La duración mínima de impresión de una capa que impondrá al ventilador de "
"girar a su velocidad mínima. La velocidad del ventilador aumenta linearmente "
"a partir de su velocidad máxima para capas que piden una duración mínima de "
"impresión hasta la velocidad mínima para capas que piden el valor "
"especificado aquí."

#: fdmprinter.json
msgctxt "cool_min_speed label"
msgid "Minimum Speed"
msgstr "Velocidad Mínima"

# doubt
#: fdmprinter.json
msgctxt "cool_min_speed description"
msgid ""
"The minimum layer time can cause the print to slow down so much it starts to "
"droop. The minimum feedrate protects against this. Even if a print gets "
"slowed down it will never be slower than this minimum speed."
msgstr ""
"La duración mínima de impresión puede hacer que la impresión ralentize a tal "
"punto que el objeto empiece a inclinarse. La velocidad mínima de "
"alimentación evita este problema. Incluso si una impresión esta ralentizada, "
"nunca será mas lento que esta velocidad mínima."

#: fdmprinter.json
msgctxt "cool_lift_head label"
msgid "Lift Head"
msgstr "Levantar el Cabezal de Impresión "

#: fdmprinter.json
msgctxt "cool_lift_head description"
msgid ""
"Lift the head away from the print if the minimum speed is hit because of "
"cool slowdown, and wait the extra time away from the print surface until the "
"minimum layer time is used up."
msgstr ""
"Levanta el cabezal de impresión del objeto en el caso que la velocidad "
"mínima este alcanzada por culpa de un ralentizo del enfriamiento, y para "
"hasta que termine la duración mínima de impresión de una capa, antes de "
"volver a imprimir."

#: fdmprinter.json
msgctxt "support label"
msgid "Support"
msgstr "Estructuras de Soporte"

#: fdmprinter.json
msgctxt "support_enable label"
msgid "Enable Support"
msgstr "Activar Estructura de Soporte"

#: fdmprinter.json
msgctxt "support_enable description"
msgid ""
"Enable exterior support structures. This will build up supporting structures "
"below the model to prevent the model from sagging or printing in mid air."
msgstr ""
"Activa las estructuras de soporte exterior. Este parámetro construye "
"estructuras de soporte por debajo del modelo para evitar que la impresora "
"imprime en el aire."

#: fdmprinter.json
msgctxt "support_type label"
msgid "Placement"
msgstr "Colocar las Estructuras de Soporte"

#: fdmprinter.json
msgctxt "support_type description"
msgid ""
"Where to place support structures. The placement can be restricted such that "
"the support structures won't rest on the model, which could otherwise cause "
"scarring."
msgstr ""
"El lugar dónde colocar las estructuras de soporte. La colocación se puede "
"restringir de tal manera que las estructuras de soporte no se quedaran en el "
"modelo, lo que de otro modo podría causar malformaciones del objeto."

#: fdmprinter.json
msgctxt "support_type option buildplate"
msgid "Touching Buildplate"
msgstr ""

#: fdmprinter.json
msgctxt "support_type option everywhere"
msgid "Everywhere"
msgstr ""

#: fdmprinter.json
msgctxt "support_angle label"
msgid "Overhang Angle"
msgstr "Ángulo de los Voladizos"

#: fdmprinter.json
#, fuzzy
msgctxt "support_angle description"
msgid ""
"The maximum angle of overhangs for which support will be added. With 0 "
"degrees being vertical, and 90 degrees being horizontal. A smaller overhang "
"angle leads to more support."
msgstr ""
"El ángulo máximo de los voladizos a partir del cual las estructuras de "
"soporte serán añadidas. Con 0 grados siendo horizontal y 90 grados siendo "
"vertical."

#: fdmprinter.json
msgctxt "support_xy_distance label"
msgid "X/Y Distance"
msgstr "Distancia X/Y"

# horizontal...
#: fdmprinter.json
msgctxt "support_xy_distance description"
msgid ""
"Distance of the support structure from the print, in the X/Y directions. "
"0.7mm typically gives a nice distance from the print so the support does not "
"stick to the surface."
msgstr ""
"La distancia horizontal entre las estructuras de soporte y el objeto en las "
"direcciones X/Y. Se recomienda una distancia de 0.7mm para que las "
"estructuras de soporte no se queden pegadas al objeto."

#: fdmprinter.json
msgctxt "support_z_distance label"
msgid "Z Distance"
msgstr "Distancia Z"

#: fdmprinter.json
msgctxt "support_z_distance description"
msgid ""
"Distance from the top/bottom of the support to the print. A small gap here "
"makes it easier to remove the support but makes the print a bit uglier. "
"0.15mm allows for easier separation of the support structure."
msgstr ""
"La distancia vertical entre la tapa y el fondo de las estructuras de soporte "
"y el objeto. Una brecha de 0.15mm facilita mucho el desprendimiento del "
"soporte pero hace que el objeto sale un poco feo."

#: fdmprinter.json
msgctxt "support_top_distance label"
msgid "Top Distance"
msgstr "Distancia Vertical de la Tapa de las Estructuras de Soporte"

#: fdmprinter.json
msgctxt "support_top_distance description"
msgid "Distance from the top of the support to the print."
msgstr "La distancia entre la tapa de las estructuras de soporte y el objeto."

#: fdmprinter.json
msgctxt "support_bottom_distance label"
msgid "Bottom Distance"
msgstr "Distancia Vertical del Fondo de las Estructuras de Soporte"

#: fdmprinter.json
msgctxt "support_bottom_distance description"
msgid "Distance from the print to the bottom of the support."
msgstr "La Distancia entre el objeto y el fondo de las estructuras de soporte."

#: fdmprinter.json
#, fuzzy
msgctxt "support_conical_enabled label"
msgid "Conical Support"
msgstr "Activar Estructura de Soporte"

#: fdmprinter.json
msgctxt "support_conical_enabled description"
msgid ""
"Experimental feature: Make support areas smaller at the bottom than at the "
"overhang."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "support_conical_angle label"
msgid "Cone Angle"
msgstr "Ángulo del Techo de las Torres"

#: fdmprinter.json
msgctxt "support_conical_angle description"
msgid ""
"The angle of the tilt of conical support. With 0 degrees being vertical, and "
"90 degrees being horizontal. Smaller angles cause the support to be more "
"sturdy, but consist of more material. Negative angles cause the base of the "
"support to be wider than the top."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "support_conical_min_width label"
msgid "Minimal Width"
msgstr "Diámetro Mínimo  "

#: fdmprinter.json
msgctxt "support_conical_min_width description"
msgid ""
"Minimal width to which conical support reduces the support areas. Small "
"widths can cause the base of the support to not act well as fundament for "
"support above."
msgstr ""

#: fdmprinter.json
msgctxt "support_bottom_stair_step_height label"
msgid "Stair Step Height"
msgstr "Altura de los escalones de la escalera"

#: fdmprinter.json
msgctxt "support_bottom_stair_step_height description"
msgid ""
"The height of the steps of the stair-like bottom of support resting on the "
"model. Small steps can cause the support to be hard to remove from the top "
"of the model."
msgstr ""
"La altura de los peldaños del fondo de las estructuras de soporte que se "
"parecen a escaleras y que se quedan sobre el objeto al final de la "
"impresión. Peldaños pequeños pueden complicar el desapego de las estructuras "
"de soporte sobre la tapa del modelo."

#: fdmprinter.json
msgctxt "support_join_distance label"
msgid "Join Distance"
msgstr "Distancia de Articulación"

#: fdmprinter.json
msgctxt "support_join_distance description"
msgid ""
"The maximum distance between support blocks, in the X/Y directions, such "
"that the blocks will merge into a single block."
msgstr ""
"La distancia máxima entre los bloques de estructuras de soporte en las "
"direcciones X/Y, de tal forma que los bloques se fusionarán en un solo "
"bloque."

#: fdmprinter.json
#, fuzzy
msgctxt "support_offset label"
msgid "Horizontal Expansion"
msgstr "Expansión Horizontal"

#: fdmprinter.json
#, fuzzy
msgctxt "support_offset description"
msgid ""
"Amount of offset applied to all support polygons in each layer. Positive "
"values can smooth out the support areas and result in more sturdy support."
msgstr ""
"La cantidad de desplazamiento aplicada a cada polígono en cada capa. Un "
"valor positivo compensa agujeros grandes; un valor negativo compensa "
"agujeros más pequeños."

#: fdmprinter.json
msgctxt "support_area_smoothing label"
msgid "Area Smoothing"
msgstr "Suavizado de Área"

#: fdmprinter.json
msgctxt "support_area_smoothing description"
msgid ""
"Maximal distance in the X/Y directions of a line segment which is to be "
"smoothed out. Ragged lines are introduced by the join distance and support "
"bridge, which cause the machine to resonate. Smoothing the support areas "
"won't cause them to break with the constraints, except it might change the "
"overhang."
msgstr ""
"La distancia máxima en las direcciones X/Y de un segmento de linea que ha de "
"ser suavizado. Lineas desiguales resultando de la distancia de articulación "
"y del puente de soporte hace resonar la impresora. Suavizar las áreas de "
"apoyo no causará que se rompan con las restricciones, excepto que podría "
"cambiar el voladizo."

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_enable label"
msgid "Enable Support Roof"
msgstr "Activar Estructura de Soporte"

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_enable description"
msgid ""
"Generate a dense top skin at the top of the support on which the model sits."
msgstr "La distancia entre la tapa de las estructuras de soporte y el objeto."

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_height label"
msgid "Support Roof Thickness"
msgstr "Espesor del fondo"

#: fdmprinter.json
msgctxt "support_roof_height description"
msgid "The height of the support roofs. "
msgstr ""

#: fdmprinter.json
msgctxt "support_roof_density label"
msgid "Support Roof Density"
msgstr ""

#: fdmprinter.json
msgctxt "support_roof_density description"
msgid ""
"This controls how densely filled the roofs of the support will be. A higher "
"percentage results in better overhangs, which are more difficult to remove."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_line_distance label"
msgid "Support Roof Line Distance"
msgstr "Distancia de Inserción del Techo en la Impresion en Alambre"

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_line_distance description"
msgid "Distance between the printed support roof lines."
msgstr "La distancia entre las lineas de las estructuras de soporte."

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_pattern label"
msgid "Support Roof Pattern"
msgstr "Patrón de la Tapa y del Fondo"

#: fdmprinter.json
#, fuzzy
msgctxt "support_roof_pattern description"
msgid "The pattern with which the top of the support is printed."
msgstr "La distancia entre la tapa de las estructuras de soporte y el objeto."

#: fdmprinter.json
msgctxt "support_roof_pattern option lines"
msgid "Lines"
msgstr ""

#: fdmprinter.json
msgctxt "support_roof_pattern option grid"
msgid "Grid"
msgstr ""

#: fdmprinter.json
msgctxt "support_roof_pattern option triangles"
msgid "Triangles"
msgstr ""

#: fdmprinter.json
msgctxt "support_roof_pattern option concentric"
msgid "Concentric"
msgstr ""

#: fdmprinter.json
msgctxt "support_roof_pattern option zigzag"
msgid "Zig Zag"
msgstr ""

#: fdmprinter.json
msgctxt "support_use_towers label"
msgid "Use towers."
msgstr "Utilizar las Torres"

#: fdmprinter.json
msgctxt "support_use_towers description"
msgid ""
"Use specialized towers to support tiny overhang areas. These towers have a "
"larger diameter than the region they support. Near the overhang the towers' "
"diameter decreases, forming a roof."
msgstr ""
"Utiliza torres especiales para apoyar pequeñas zonas de voladizos. Estas "
"torres tienen un diámetro más ancho que la zona de voladizo que sostienen."

#: fdmprinter.json
msgctxt "support_minimal_diameter label"
msgid "Minimal Diameter"
msgstr "Diámetro Mínimo  "

#: fdmprinter.json
msgctxt "support_minimal_diameter description"
msgid ""
"Maximal diameter in the X/Y directions of a small area which is to be "
"supported by a specialized support tower. "
msgstr ""
"El diámetro máximo en las direcciones X/Y de una zona pequeña que recibe el "
"soporte de una torre."

#: fdmprinter.json
msgctxt "support_tower_diameter label"
msgid "Tower Diameter"
msgstr "Diámetro de las Torres"

#: fdmprinter.json
msgctxt "support_tower_diameter description"
msgid "The diameter of a special tower. "
msgstr "El diámetro de un torre especial."

#: fdmprinter.json
msgctxt "support_tower_roof_angle label"
msgid "Tower Roof Angle"
msgstr "Ángulo del Techo de las Torres"

#: fdmprinter.json
msgctxt "support_tower_roof_angle description"
msgid ""
"The angle of the rooftop of a tower. Larger angles mean more pointy towers. "
msgstr "El ángulo de la azotea de una torre."

#: fdmprinter.json
msgctxt "support_pattern label"
msgid "Pattern"
msgstr "Patrón "

#: fdmprinter.json
msgctxt "support_pattern description"
msgid ""
"Cura supports 3 distinct types of support structure. First is a grid based "
"support structure which is quite solid and can be removed as 1 piece. The "
"second is a line based support structure which has to be peeled off line by "
"line. The third is a structure in between the other two; it consists of "
"lines which are connected in an accordeon fashion."
msgstr ""
"Cura propone 3 distintos tipos de estructura de soporte. El primero es una "
"cuadrícula bastante solida y fácil de quitar. El segundo es una estructura "
"de soporte lineal que se pela linea por linea. El tercer tipo es una "
"estructura de soporte similar a los dos otros tipos; esta compuesto de "
"lineas conectadas entre ellas por una articulación en forma de acordeón."

#: fdmprinter.json
msgctxt "support_pattern option lines"
msgid "Lines"
msgstr ""

#: fdmprinter.json
msgctxt "support_pattern option grid"
msgid "Grid"
msgstr ""

#: fdmprinter.json
msgctxt "support_pattern option triangles"
msgid "Triangles"
msgstr ""

#: fdmprinter.json
msgctxt "support_pattern option concentric"
msgid "Concentric"
msgstr ""

#: fdmprinter.json
msgctxt "support_pattern option zigzag"
msgid "Zig Zag"
msgstr ""

#: fdmprinter.json
msgctxt "support_connect_zigzags label"
msgid "Connect ZigZags"
msgstr "Conectar Zig Zags"

#: fdmprinter.json
msgctxt "support_connect_zigzags description"
msgid ""
"Connect the ZigZags. Makes them harder to remove, but prevents stringing of "
"disconnected zigzags."
msgstr ""
"Conecta los Zig Zags. Resulta más difícil de quitarlos, pero evita el "
"encordado de zig zags desconectados."

#: fdmprinter.json
#, fuzzy
msgctxt "support_infill_rate label"
msgid "Fill Amount"
msgstr "Cantidad de Relleno"

#: fdmprinter.json
#, fuzzy
msgctxt "support_infill_rate description"
msgid ""
"The amount of infill structure in the support, less infill gives weaker "
"support which is easier to remove."
msgstr ""
"La cantidad de relleno de las estructuras de soporte, menos relleno produce "
"estructuras de soporte más débiles y más fáciles de quitar."

#: fdmprinter.json
msgctxt "support_line_distance label"
msgid "Line distance"
msgstr "Distancia entre las Lineas"

#: fdmprinter.json
msgctxt "support_line_distance description"
msgid "Distance between the printed support lines."
msgstr "La distancia entre las lineas de las estructuras de soporte."

#: fdmprinter.json
msgctxt "platform_adhesion label"
msgid "Platform Adhesion"
msgstr "Tipo de Adherencia a la Plataforma"

#: fdmprinter.json
msgctxt "adhesion_type label"
msgid "Type"
msgstr "Tipo"

#: fdmprinter.json
msgctxt "adhesion_type description"
msgid ""
"Different options that help in preventing corners from lifting due to "
"warping. Brim adds a single-layer-thick flat area around your object which "
"is easy to cut off afterwards, and it is the recommended option. Raft adds a "
"thick grid below the object and a thin interface between this and your "
"object. (Note that enabling the brim or raft disables the skirt.)"
msgstr ""
"Diferentes opciones que ayudan en la prevención del efecto de levantamiento "
"de las esquinas del modelo mientras se esta imprimiendo. La visera agrega "
"una sola capa plana de material alrededor del objeto que se puede quitar "
"fácilmente: se recomienda mucho utilizar esta opción. La balsa agrega una "
"cuadrícula espesa por debajo del objeto más una interfaz fina entre la "
"cuadrícula y el objeto. (Tenga en cuenta que activar la visera o la balsa "
"desactiva le falda.)"

#: fdmprinter.json
#, fuzzy
msgctxt "adhesion_type option skirt"
msgid "Skirt"
msgstr "Velocidad de Impresión de la Falda"

#: fdmprinter.json
msgctxt "adhesion_type option brim"
msgid "Brim"
msgstr ""

#: fdmprinter.json
msgctxt "adhesion_type option raft"
msgid "Raft"
msgstr ""

#: fdmprinter.json
msgctxt "skirt_line_count label"
msgid "Skirt Line Count"
msgstr "Número de lineas de la Falda"

#: fdmprinter.json
msgctxt "skirt_line_count description"
msgid ""
"The skirt is a line drawn around the first layer of the. This helps to prime "
"your extruder, and to see if the object fits on your platform. Setting this "
"to 0 will disable the skirt. Multiple skirt lines can help to prime your "
"extruder better for small objects."
msgstr ""
"La falda es una linea impresa alrededor de la primera capa del objeto. Ayuda "
"a preparar el extrusor, y a ver si el objeto cabe en la plataforma. Poner "
"este valor a 0 desactivará la falda. Imprimir varias lineas de falda puede "
"ayudar a preparar el extrusor para la impresión de pequeños objetos."

#: fdmprinter.json
msgctxt "skirt_gap label"
msgid "Skirt Distance"
msgstr "Distancia de la Falda"

#: fdmprinter.json
msgctxt "skirt_gap description"
msgid ""
"The horizontal distance between the skirt and the first layer of the print.\n"
"This is the minimum distance, multiple skirt lines will extend outwards from "
"this distance."
msgstr ""
"La distancia horizontal entre la falda y la primera capa del objeto.\n"
"Es la distancia  mínima, la impresión de varias lineas de falda extenderá la "
"falda hacia el exterior de esta distancia. "

#: fdmprinter.json
msgctxt "skirt_minimal_length label"
msgid "Skirt Minimum Length"
msgstr "Longitud Mínima de la Falda"

#: fdmprinter.json
msgctxt "skirt_minimal_length description"
msgid ""
"The minimum length of the skirt. If this minimum length is not reached, more "
"skirt lines will be added to reach this minimum length. Note: If the line "
"count is set to 0 this is ignored."
msgstr ""
"La longitud mínima de la falda. Si esta longitud mínima no se alcanza, más "
"linea se agregaran  para alcanzar esta longitud mínima. Tenga en cuenta que "
"si el número de lineas es de 0, se ignorará."

#: fdmprinter.json
msgctxt "brim_line_count label"
msgid "Brim Line Count"
msgstr "Número de Lineas de la Visera"

#: fdmprinter.json
msgctxt "brim_line_count description"
msgid ""
"The amount of lines used for a brim: More lines means a larger brim which "
"sticks better, but this also makes your effective print area smaller."
msgstr ""
"La cantidad de lineas de la visera: Más lineas produce una visera más ancha "
"que pega bien a la plataforma, pero reduce también la zona de impresión."

#: fdmprinter.json
msgctxt "raft_margin label"
msgid "Raft Extra Margin"
msgstr "Margen Exterior de la Balsa"

#: fdmprinter.json
msgctxt "raft_margin description"
msgid ""
"If the raft is enabled, this is the extra raft area around the object which "
"is also given a raft. Increasing this margin will create a stronger raft "
"while using more material and leaving less area for your print."
msgstr ""
"Si la balsa esta activada, este margen es una zona extra de balsa alrededor "
"de la balsa. Aumentar este margen creará un balsa más resistente mientras "
"utilizando más material y reduciendo también la zona de impresión."

#: fdmprinter.json
msgctxt "raft_airgap label"
msgid "Raft Air-gap"
msgstr "Brecha de la Balsa"

#: fdmprinter.json
msgctxt "raft_airgap description"
msgid ""
"The gap between the final raft layer and the first layer of the object. Only "
"the first layer is raised by this amount to lower the bonding between the "
"raft layer and the object. Makes it easier to peel off the raft."
msgstr ""
"La brecha entre la capa final de la balsa y la primera capa del objeto. La "
"primera capa del objeto se imprime un poco elevada en el aire de este valor "
"para reducir la zona de contacto entre la ultima capa de la balsa y la "
"primera capa del objeto. Facilita quitarle el draft al objeto."

#: fdmprinter.json
msgctxt "raft_surface_layers label"
msgid "Raft Surface Layers"
msgstr "Capas Superficiales de la Balsa"

#: fdmprinter.json
msgctxt "raft_surface_layers description"
msgid ""
"The number of surface layers on top of the 2nd raft layer. These are fully "
"filled layers that the object sits on. 2 layers usually works fine."
msgstr ""
"El número de capas superficiales encima de la segunda capa de la balsa. El "
"objeto se imprime sobre estas capas superficiales llenas directamente. 2 "
"capas funciona bien."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_thickness label"
msgid "Raft Surface Thickness"
msgstr "Espesor de la Interfaz de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_thickness description"
msgid "Layer thickness of the surface raft layers."
msgstr "El espesor de la segunda capa de la balsa."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_line_width label"
msgid "Raft Surface Line Width"
msgstr "Anchura de las lineas de la Interfaz de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_line_width description"
msgid ""
"Width of the lines in the surface raft layers. These can be thin lines so "
"that the top of the raft becomes smooth."
msgstr ""
"La anchura de las lineas que componen la primera capa de la balsa. Tienen "
"que ser lineas espesas para adherirse correctamente a la plataforma de la "
"impresora. "

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_line_spacing label"
msgid "Raft Surface Spacing"
msgstr "Espacio entre las Lineas de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_line_spacing description"
msgid ""
"The distance between the raft lines for the surface raft layers. The spacing "
"of the interface should be equal to the line width, so that the surface is "
"solid."
msgstr ""
"El espacio entre las lineas que componen la balsa. Las 2 primeras capas de "
"la balsa tienen esta cantidad de espacio entre las lineas que las componen."

#: fdmprinter.json
msgctxt "raft_interface_thickness label"
msgid "Raft Interface Thickness"
msgstr "Espesor de la Interfaz de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_thickness description"
msgid "Layer thickness of the interface raft layer."
msgstr "El espesor de la segunda capa de la balsa."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_line_width label"
msgid "Raft Interface Line Width"
msgstr "Anchura de las lineas de la Interfaz de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_line_width description"
msgid ""
"Width of the lines in the interface raft layer. Making the second layer "
"extrude more causes the lines to stick to the bed."
msgstr ""
"La anchura de las lineas que componen la primera capa de la balsa. Tienen "
"que ser lineas espesas para adherirse correctamente a la plataforma de la "
"impresora. "

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_line_spacing label"
msgid "Raft Interface Spacing"
msgstr "Espacio entre las Lineas de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_line_spacing description"
msgid ""
"The distance between the raft lines for the interface raft layer. The "
"spacing of the interface should be quite wide, while being dense enough to "
"support the surface raft layers."
msgstr ""
"El espacio entre las lineas que componen la balsa. Las 2 primeras capas de "
"la balsa tienen esta cantidad de espacio entre las lineas que las componen."

#: fdmprinter.json
msgctxt "raft_base_thickness label"
msgid "Raft Base Thickness"
msgstr "Espesor de la base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_thickness description"
msgid ""
"Layer thickness of the base raft layer. This should be a thick layer which "
"sticks firmly to the printer bed."
msgstr ""
"El espesor de la primera capa de la balsa. Tiene que ser una capa espesa que "
"pega firmemente a la plataforma de la impresora."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_line_width label"
msgid "Raft Base Line Width"
msgstr "Anchura de las Lineas de la Base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_line_width description"
msgid ""
"Width of the lines in the base raft layer. These should be thick lines to "
"assist in bed adhesion."
msgstr ""
"La anchura de las lineas que componen la primera capa de la balsa. Tienen "
"que ser lineas espesas para adherirse correctamente a la plataforma de la "
"impresora. "

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_line_spacing label"
msgid "Raft Line Spacing"
msgstr "Espacio entre las Lineas de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_line_spacing description"
msgid ""
"The distance between the raft lines for the base raft layer. Wide spacing "
"makes for easy removal of the raft from the build plate."
msgstr ""
"El espacio entre las lineas que componen la balsa. Las 2 primeras capas de "
"la balsa tienen esta cantidad de espacio entre las lineas que las componen."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_speed label"
msgid "Raft Print Speed"
msgstr "Velocidad de Impresión de la Base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_speed description"
msgid "The speed at which the raft is printed."
msgstr ""
"La velocidad a la que el filamento se retrocede en la boquilla justo después "
"de la retracción."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_speed label"
msgid "Raft Surface Print Speed"
msgstr "Velocidad de Impresión de la Base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_speed description"
msgid ""
"The speed at which the surface raft layers are printed. This should be "
"printed a bit slower, so that the nozzle can slowly smooth out adjacent "
"surface lines."
msgstr ""
"La velocidad de impresión de la primera capa de la balsa. Tiene que "
"imprimirse lentamente porque la cantidad de material saliendo de la boquilla "
"es bastante alta."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_speed label"
msgid "Raft Interface Print Speed"
msgstr "Velocidad de Impresión de la Base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_speed description"
msgid ""
"The speed at which the interface raft layer is printed. This should be "
"printed quite slowly, as the amount of material coming out of the nozzle is "
"quite high."
msgstr ""
"La velocidad de impresión de la primera capa de la balsa. Tiene que "
"imprimirse lentamente porque la cantidad de material saliendo de la boquilla "
"es bastante alta."

#: fdmprinter.json
msgctxt "raft_base_speed label"
msgid "Raft Base Print Speed"
msgstr "Velocidad de Impresión de la Base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_speed description"
msgid ""
"The speed at which the base raft layer is printed. This should be printed "
"quite slowly, as the amount of material coming out of the nozzle is quite "
"high."
msgstr ""
"La velocidad de impresión de la primera capa de la balsa. Tiene que "
"imprimirse lentamente porque la cantidad de material saliendo de la boquilla "
"es bastante alta."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_fan_speed label"
msgid "Raft Fan Speed"
msgstr "Velocidad del Ventilador"

#: fdmprinter.json
msgctxt "raft_fan_speed description"
msgid "The fan speed for the raft."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_fan_speed label"
msgid "Raft Surface Fan Speed"
msgstr "Capas Superficiales de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_surface_fan_speed description"
msgid "The fan speed for the surface raft layers."
msgstr "El espesor de la segunda capa de la balsa."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_fan_speed label"
msgid "Raft Interface Fan Speed"
msgstr "Anchura de las lineas de la Interfaz de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_interface_fan_speed description"
msgid "The fan speed for the interface raft layer."
msgstr "El espesor de la segunda capa de la balsa."

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_fan_speed label"
msgid "Raft Base Fan Speed"
msgstr "Velocidad de Impresión de la Base de la Balsa"

#: fdmprinter.json
#, fuzzy
msgctxt "raft_base_fan_speed description"
msgid "The fan speed for the base raft layer."
msgstr "El espesor de la segunda capa de la balsa."

#: fdmprinter.json
#, fuzzy
msgctxt "draft_shield_enabled label"
msgid "Enable Draft Shield"
msgstr "Activar Retracción"

#: fdmprinter.json
msgctxt "draft_shield_enabled description"
msgid ""
"Enable exterior draft shield. This will create a wall around the object "
"which traps (hot) air and shields against gusts of wind. Especially useful "
"for materials which warp easily."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "draft_shield_dist label"
msgid "Draft Shield X/Y Distance"
msgstr "Distancia X/Y"

#: fdmprinter.json
#, fuzzy
msgctxt "draft_shield_dist description"
msgid "Distance of the draft shield from the print, in the X/Y directions."
msgstr "La distancia entre la tapa de las estructuras de soporte y el objeto."

#: fdmprinter.json
msgctxt "draft_shield_height_limitation label"
msgid "Draft Shield Limitation"
msgstr ""

#: fdmprinter.json
msgctxt "draft_shield_height_limitation description"
msgid "Whether to limit the height of the draft shield"
msgstr ""

#: fdmprinter.json
msgctxt "draft_shield_height_limitation option full"
msgid "Full"
msgstr ""

#: fdmprinter.json
msgctxt "draft_shield_height_limitation option limited"
msgid "Limited"
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "draft_shield_height label"
msgid "Draft Shield Height"
msgstr "Altura de los escalones de la escalera"

#: fdmprinter.json
msgctxt "draft_shield_height description"
msgid ""
"Height limitation on the draft shield. Above this height no draft shield "
"will be printed."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "meshfix label"
msgid "Mesh Fixes"
msgstr "Correcciones"

#: fdmprinter.json
#, fuzzy
msgctxt "meshfix_union_all label"
msgid "Union Overlapping Volumes"
msgstr "Evitar Superponer Paredes."

#: fdmprinter.json
msgctxt "meshfix_union_all description"
msgid ""
"Ignore the internal geometry arising from overlapping volumes and print the "
"volumes as one. This may cause internal cavaties to disappear."
msgstr ""

#: fdmprinter.json
msgctxt "meshfix_union_all_remove_holes label"
msgid "Remove All Holes"
msgstr ""

#: fdmprinter.json
msgctxt "meshfix_union_all_remove_holes description"
msgid ""
"Remove the holes in each layer and keep only the outside shape. This will "
"ignore any invisible internal geometry. However, it also ignores layer holes "
"which can be viewed from above or below."
msgstr ""

#: fdmprinter.json
msgctxt "meshfix_extensive_stitching label"
msgid "Extensive Stitching"
msgstr ""

#: fdmprinter.json
msgctxt "meshfix_extensive_stitching description"
msgid ""
"Extensive stitching tries to stitch up open holes in the mesh by closing the "
"hole with touching polygons. This option can introduce a lot of processing "
"time."
msgstr ""

#: fdmprinter.json
msgctxt "meshfix_keep_open_polygons label"
msgid "Keep Disconnected Faces"
msgstr ""

#: fdmprinter.json
msgctxt "meshfix_keep_open_polygons description"
msgid ""
"Normally Cura tries to stitch up small holes in the mesh and remove parts of "
"a layer with big holes. Enabling this option keeps those parts which cannot "
"be stitched. This option should be used as a last resort option when all "
"else doesn produce proper GCode."
msgstr ""

#: fdmprinter.json
msgctxt "blackmagic label"
msgid "Special Modes"
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "print_sequence label"
msgid "Print sequence"
msgstr "Velocidad de la Impresión"

#: fdmprinter.json
msgctxt "print_sequence description"
msgid ""
"Whether to print all objects one layer at a time or to wait for one object "
"to finish, before moving on to the next. One at a time mode is only possible "
"if all models are separated such that the whole print head can move between "
"and all models are lower than the distance between the nozzle and the X/Y "
"axles."
msgstr ""

#: fdmprinter.json
msgctxt "print_sequence option all_at_once"
msgid "All at Once"
msgstr ""

#: fdmprinter.json
msgctxt "print_sequence option one_at_a_time"
msgid "One at a Time"
msgstr ""

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode label"
msgid "Surface Mode"
msgstr ""

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode description"
msgid ""
"Print the surface instead of the volume. No infill, no top/bottom skin, just "
"a single wall of which the middle coincides with the surface of the mesh. "
"It's also possible to do both: print the insides of a closed volume as "
"normal, but print all polygons not part of a closed volume as surface."
msgstr ""

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode option normal"
msgid "Normal"
msgstr ""

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode option surface"
msgid "Surface"
msgstr ""

#: fdmprinter.json
msgctxt "magic_mesh_surface_mode option both"
msgid "Both"
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "magic_spiralize label"
msgid "Spiralize Outer Contour"
msgstr "Imprimir el Contorno Exterior en Espiral. "

#: fdmprinter.json
msgctxt "magic_spiralize description"
msgid ""
"Spiralize smooths out the Z move of the outer edge. This will create a "
"steady Z increase over the whole print. This feature turns a solid object "
"into a single walled print with a solid bottom. This feature used to be "
"called ‘Joris’ in older versions."
msgstr ""

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_enabled label"
msgid "Fuzzy Skin"
msgstr ""

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_enabled description"
msgid ""
"Randomly jitter while printing the outer wall, so that the surface has a "
"rough and fuzzy look."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "magic_fuzzy_skin_thickness label"
msgid "Fuzzy Skin Thickness"
msgstr "Espesor de la Cáscara"

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_thickness description"
msgid ""
"The width within which to jitter. It's advised to keep this below the outer "
"wall width, since the inner walls are unaltered."
msgstr ""

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_density label"
msgid "Fuzzy Skin Density"
msgstr ""

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_density description"
msgid ""
"The average density of points introduced on each polygon in a layer. Note "
"that the original points of the polygon are discarded, so a low density "
"results in a reduction of the resolution."
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "magic_fuzzy_skin_point_dist label"
msgid "Fuzzy Skin Point Distance"
msgstr "Distancia de la Falda"

#: fdmprinter.json
msgctxt "magic_fuzzy_skin_point_dist description"
msgid ""
"The average distance between the random points introduced on each line "
"segment. Note that the original points of the polygon are discarded, so a "
"high smoothness results in a reduction of the resolution. This value must be "
"higher than half the Fuzzy Skin Thickness."
msgstr ""

#: fdmprinter.json
msgctxt "wireframe_enabled label"
msgid "Wire Printing"
msgstr "Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_enabled description"
msgid ""
"Print only the outside surface with a sparse webbed structure, printing 'in "
"thin air'. This is realized by horizontally printing the contours of the "
"model at given Z intervals which are connected via upward and diagonally "
"downward lines."
msgstr ""
"Imprime la parte exterior del objeto en forma de tela de araña escasa. Se "
"hace imprimiendo horizontalmente los contornos del modelo a dados intervalos "
"del eje Z conectados vía lineas verticales y diagonales."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_height label"
msgid "WP Connection Height"
msgstr "Altura de Conexión de la Impresión en Alambre "

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_height description"
msgid ""
"The height of the upward and diagonally downward lines between two "
"horizontal parts. This determines the overall density of the net structure. "
"Only applies to Wire Printing."
msgstr ""
"La altura de las líneas hacia arriba y hacia abajo en diagonal entre dos "
"partes horizontales. Sólo se aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_roof_inset label"
msgid "WP Roof Inset Distance"
msgstr "Distancia de Inserción del Techo en la Impresion en Alambre"

#: fdmprinter.json
msgctxt "wireframe_roof_inset description"
msgid ""
"The distance covered when making a connection from a roof outline inward. "
"Only applies to Wire Printing."
msgstr ""
"La distancia recorrida al hacer una conexión desde un contorno del techo "
"interior. Sólo se aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_printspeed label"
msgid "WP speed"
msgstr "Velocidad de la Impresión"

#: fdmprinter.json
msgctxt "wireframe_printspeed description"
msgid ""
"Speed at which the nozzle moves when extruding material. Only applies to "
"Wire Printing."
msgstr ""
"La velocidad a la que la boquilla se mueve cuando extruye el material. Sólo "
"se aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_printspeed_bottom label"
msgid "WP Bottom Printing Speed"
msgstr "Velocidad de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_printspeed_bottom description"
msgid ""
"Speed of printing the first layer, which is the only layer touching the "
"build platform. Only applies to Wire Printing."
msgstr ""
"La velocidad de impresión de la primera capa la cual es la única capa en "
"contacto con la plataforma. Sólo se aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_printspeed_up label"
msgid "WP Upward Printing Speed"
msgstr "Velocidad Vertical de Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_printspeed_up description"
msgid ""
"Speed of printing a line upward 'in thin air'. Only applies to Wire Printing."
msgstr ""
"La velocidad de impresión de una linea vertical 'en el aire'. Sólo se aplica "
"a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_printspeed_down label"
msgid "WP Downward Printing Speed"
msgstr "Velocidad Diagonal de Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_printspeed_down description"
msgid ""
"Speed of printing a line diagonally downward. Only applies to Wire Printing."
msgstr ""
"La velocidad de impresión de una linea diagonal hacia abajo. Sólo se aplica "
"a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_printspeed_flat label"
msgid "WP Horizontal Printing Speed"
msgstr "Velocidad Horizontal de Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_printspeed_flat description"
msgid ""
"Speed of printing the horizontal contours of the object. Only applies to "
"Wire Printing."
msgstr ""
"La velocidad de impresión de los contornos horizontales del objeto. Sólo se "
"aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_flow label"
msgid "WP Flow"
msgstr "Flujo"

#: fdmprinter.json
msgctxt "wireframe_flow description"
msgid ""
"Flow compensation: the amount of material extruded is multiplied by this "
"value. Only applies to Wire Printing."
msgstr ""
"La compensación de caudal: la cantidad de material extruído se multiplica "
"por este valor. Sólo se aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_flow_connection label"
msgid "WP Connection Flow"
msgstr "Caudal de Conexión de Alambres"

#: fdmprinter.json
msgctxt "wireframe_flow_connection description"
msgid "Flow compensation when going up or down. Only applies to Wire Printing."
msgstr ""
"El caudal de compensación al bajar o al subir. Sólo se aplica a la impresión "
"en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_flow_flat label"
msgid "WP Flat Flow"
msgstr "Caudal de Impresión en Alambre para Lineas planas"

#: fdmprinter.json
msgctxt "wireframe_flow_flat description"
msgid ""
"Flow compensation when printing flat lines. Only applies to Wire Printing."
msgstr ""
"La compensación de caudal al imprimir lineas planas. Sólo se aplica a la "
"impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_top_delay label"
msgid "WP Top Delay"
msgstr "Retraso al Alza de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_top_delay description"
msgid ""
"Delay time after an upward move, so that the upward line can harden. Only "
"applies to Wire Printing."
msgstr ""
"El retraso después de un movimiento al alza para que la línea ascendente "
"endurece."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_bottom_delay label"
msgid "WP Bottom Delay"
msgstr "Retraso a la Baja de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_bottom_delay description"
msgid ""
"Delay time after a downward move. Only applies to Wire Printing. Only "
"applies to Wire Printing."
msgstr ""
"El retraso después de un movimiento a la baja. Sólo se aplica a la impresión "
"en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_flat_delay label"
msgid "WP Flat Delay"
msgstr "Retraso Horizontal de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_flat_delay description"
msgid ""
"Delay time between two horizontal segments. Introducing such a delay can "
"cause better adhesion to previous layers at the connection points, while too "
"large delay times cause sagging. Only applies to Wire Printing."
msgstr ""
"El retraso entre 2 segmentos horizontales. Aplicar un retraso puede "
"facilitar la adherencia a las capas previas al nivel de los puntos de "
"conexión, mientras retrasos muy largos pueden causar hundidos. Sólo se "
"aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_up_half_speed label"
msgid "WP Ease Upward"
msgstr "Movimiento Alcista de la Impresión en Alambre "

#: fdmprinter.json
msgctxt "wireframe_up_half_speed description"
msgid ""
"Distance of an upward move which is extruded with half speed.\n"
"This can cause better adhesion to previous layers, while not heating the "
"material in those layers too much. Only applies to Wire Printing."
msgstr ""
"La distancia de un movimiento alcista extruído a la mitad de la velocidad.\n"
"Puede facilitar la adherencia a las capas previas mientras no calentar "
"demasiado el material para estas capas. Sólo se aplica a la impresión en "
"alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_top_jump label"
msgid "WP Knot Size"
msgstr "Tamaño de Nudo en la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_top_jump description"
msgid ""
"Creates a small knot at the top of an upward line, so that the consecutive "
"horizontal layer has a better chance to connect to it. Only applies to Wire "
"Printing."
msgstr ""
"Crea un pequeño nudo encima de una linea ascendente de modo que la capa "
"horizontal siguiente se conecte bien con el resto del objeto. Sólo se aplica "
"a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_fall_down label"
msgid "WP Fall Down"
msgstr "Distancia de Caída de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_fall_down description"
msgid ""
"Distance with which the material falls down after an upward extrusion. This "
"distance is compensated for. Only applies to Wire Printing."
msgstr ""
"La distancia con la cual el material se cae después de una extrusión a la "
"alza."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_drag_along label"
msgid "WP Drag along"
msgstr "Distancia de Rastro de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_drag_along description"
msgid ""
"Distance with which the material of an upward extrusion is dragged along "
"with the diagonally downward extrusion. This distance is compensated for. "
"Only applies to Wire Printing."
msgstr ""
"La distancia con la cual el material de una extrusión alcista se arrastra "
"con la extrusión diagonal hacia abajo. Sólo se aplica a la impresión en "
"alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_strategy label"
msgid "WP Strategy"
msgstr "Estrategia de Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_strategy description"
msgid ""
"Strategy for making sure two consecutive layers connect at each connection "
"point. Retraction lets the upward lines harden in the right position, but "
"may cause filament grinding. A knot can be made at the end of an upward line "
"to heighten the chance of connecting to it and to let the line cool; however "
"it may require slow printing speeds. Another strategy is to compensate for "
"the sagging of the top of an upward line; however, the lines won't always "
"fall down as predicted."
msgstr ""
"La estrategia para asegurarse que 2 capas consecutivas se conectan a cada "
"punto de conexión. La retracción permite a las lineas verticales de "
"endurecerse en la posición adecuada pero podría moler el filamento. Se puede "
"hacer un nudo al fin de una linea vertical para aumentar su capacidad a "
"conectarse a este y dejar que la linea se enfríe; sin embargo puede requerir "
"una velocidad de impresión lenta. Otra estrategia consiste en compensar la "
"flacidez de la parte superior de una linea hacia arriba; sin embargo, las "
"lineas no se caerán siempre como se predijo."

#: fdmprinter.json
msgctxt "wireframe_strategy option compensate"
msgid "Compensate"
msgstr ""

#: fdmprinter.json
msgctxt "wireframe_strategy option knot"
msgid "Knot"
msgstr ""

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_strategy option retract"
msgid "Retract"
msgstr "Velocidad de la Retracción"

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_straight_before_down label"
msgid "WP Straighten Downward Lines"
msgstr "Alineación de las Lineas Descendentes de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_straight_before_down description"
msgid ""
"Percentage of a diagonally downward line which is covered by a horizontal "
"line piece. This can prevent sagging of the top most point of upward lines. "
"Only applies to Wire Printing."
msgstr ""
"El porcentaje de una línea descendente en diagonal que está cubierta por un "
"pedazo de línea horizontal. Esto puede evitar la flacidez de la parte "
"superior en la mayor parte de los puntos de las líneas ascendentes."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_roof_fall_down label"
msgid "WP Roof Fall Down"
msgstr "Distancia de Caída del Techo de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_roof_fall_down description"
msgid ""
"The distance which horizontal roof lines printed 'in thin air' fall down "
"when being printed. This distance is compensated for. Only applies to Wire "
"Printing."
msgstr ""
"La distancia a la que las líneas horizontales del techo impresas 'en el "
"aire' caen cuando se está imprimiendo. Sólo se aplica a la impresión en "
"alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_roof_drag_along label"
msgid "WP Roof Drag Along"
msgstr "Distancia de Rastro del Techo de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_roof_drag_along description"
msgid ""
"The distance of the end piece of an inward line which gets dragged along "
"when going back to the outer outline of the roof. This distance is "
"compensated for. Only applies to Wire Printing."
msgstr ""
"La distancia recorrida por la pieza final de una línea interior que se ve "
"arrastrada a lo largo cuando vuelve al contorno exterior del techo. Sólo se "
"aplica a la impresión en alambre."

#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_roof_outer_delay label"
msgid "WP Roof Outer Delay"
msgstr "Retraso Exterior del Techo de la Impresión en Alambre"

#: fdmprinter.json
msgctxt "wireframe_roof_outer_delay description"
msgid ""
"Time spent at the outer perimeters of hole which is to become a roof. Larger "
"times can ensure a better connection. Only applies to Wire Printing."
msgstr ""
"El tiempo pasado al perímetro exterior de agujeros que se transformaran en "
"techos luego. Más tiempo aumenta la solidez de la conexiones. Sólo se aplica "
"a la impresión en alambre."

# ?
#: fdmprinter.json
#, fuzzy
msgctxt "wireframe_nozzle_clearance label"
msgid "WP Nozzle Clearance"
msgstr "Nivelación de la Boquilla para la Impresión en Alambre."

#: fdmprinter.json
msgctxt "wireframe_nozzle_clearance description"
msgid ""
"Distance between the nozzle and horizontally downward lines. Larger "
"clearance results in diagonally downward lines with a less steep angle, "
"which in turn results in less upward connections with the next layer. Only "
"applies to Wire Printing."
msgstr ""
"La distancia entre la boquilla y las líneas horizontales a la baja. Más "
"espacio resulta con líneas en diagonal hacia abajo con un ángulo menos "
"pronunciado, lo que a su vez se traduce en menos conexiones hacia arriba con "
"la siguiente capa. Sólo se aplica a la impresión en alambre."

#~ msgctxt "layer_height_0 label"
#~ msgid "Initial Layer Thickness"
#~ msgstr "Espesor de la Primera Capa."

#~ msgctxt "wall_line_width_0 label"
#~ msgid "First Wall Line Width"
#~ msgstr "Anchura de la Primera Linea más externa de la Pared"

#~ msgctxt "raft_interface_linewidth description"
#~ msgid ""
#~ "Width of the 2nd raft layer lines. These lines should be thinner than the "
#~ "first layer, but strong enough to attach the object to."
#~ msgstr ""
#~ "La anchura de la lineas de la segunda capa de la balsa. Estas lineas "
#~ "tienen que ser mas finas que las de la primera capa pero suficiente "
#~ "resistentes para pegar al objeto."

#~ msgctxt "wireframe_printspeed label"
#~ msgid "Wire Printing speed"
#~ msgstr "Velocidad de la Impresión en Alambre"

#~ msgctxt "wireframe_flow label"
#~ msgid "Wire Printing Flow"
#~ msgstr "Caudal de la Impresión en Alambre"