hw/riscv: Add Microblaze V generic board

Add a basic board with interrupt controller (intc), timer, serial
(uartlite), small memory called LMB@0 (128kB) and DDR@0x80000000
(configured via command line eg. -m 2g).
This is basic configuration which matches HW generated out of AMD Vivado
(design tools). But initial configuration is going beyond what it is
configured by default because validation should be done on other
configurations too. That's why wire also additional uart16500, axi
ethernet(with axi dma).
GPIOs, i2c and qspi is also listed for completeness.

IRQ map is: (addr)
0 - timer (0x41c00000)
1 - uartlite (0x40600000)
2 - i2c (0x40800000)
3 - qspi (0x44a00000)
4 - uart16550 (0x44a10000)
5 - emaclite (0x40e00000)
6 - timer2 (0x41c10000)
7 - axi emac (0x40c00000)
8 - axi dma (0x41e00000)
9 - axi dma
10 - gpio (0x40000000)
11 - gpio2 (0x40010000)
12 - gpio3 (0x40020000)

Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241125134739.18189-1-sai.pavan.boddu@amd.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>

docs/system/riscv/microblaze-v-generic.rst

@@ -0,0 +1,42 @@
+Microblaze-V generic board (``amd-microblaze-v-generic``)
+=========================================================
+The AMD MicroBlaze™ V processor is a soft-core RISC-V processor IP for AMD
+adaptive SoCs and FPGAs. The MicroBlaze™ V processor is based on the 32-bit (or
+64-bit) RISC-V instruction set architecture (ISA) and contains interfaces
+compatible with the classic MicroBlaze™ V processor (i.e it is a drop in
+replacement for the classic MicroBlaze™ processor in existing RTL designs).
+More information can be found in below document.
+
+https://docs.amd.com/r/en-US/ug1629-microblaze-v-user-guide/MicroBlaze-V-Architecture
+
+The MicroBlaze™ V generic board in QEMU has following supported devices:
+
+    - timer
+    - uartlite
+    - uart16550
+    - emaclite
+    - timer2
+    - axi emac
+    - axi dma
+
+The MicroBlaze™ V core in QEMU has the following configuration:
+
+    - RV32I base integer instruction set
+    - "Zicsr" Control and Status register instructions
+    - "Zifencei" instruction-fetch
+    - Extensions: m, a, f, c
+
+Running
+"""""""
+Below is an example command line for launching mainline U-boot
+(xilinx_mbv32_defconfig) on the Microblaze-V generic board.
+
+.. code-block:: bash
+
+   $ qemu-system-riscv32 -M amd-microblaze-v-generic \
+     -display none \
+     -device loader,addr=0x80000000,file=u-boot-spl.bin,cpu-num=0 \
+     -device loader,addr=0x80200000,file=u-boot.img \
+     -serial mon:stdio \
+     -device loader,addr=0x83000000,file=system.dtb \
+     -m 2g