diff --git a/config/generic-azteeg-x3-pro.cfg b/config/generic-azteeg-x3-pro.cfg
index affce2ca4..1f33a0e3f 100644
--- a/config/generic-azteeg-x3-pro.cfg
+++ b/config/generic-azteeg-x3-pro.cfg
@@ -5,14 +5,14 @@
 #
 #Flashing the MCU.
 # -SSH into your device running Klipper (Raspberry Pi, etc...)
-# -Determine the port ID using these instructions: 
+# -Determine the port ID using these instructions:
 #  https://www.klipper3d.org/FAQ.html#wheres-my-serial-port
 # -Make sure your locale is set correctly on your device running
 #  klipper. For my Rasperry Pi, I needed to run `sudo raspi-config`
 #  and set the locale in `localisation options`.
 # -Run `make menuconfig` to open the menu to set MCU settings.
 #  - Micro-controller Architecture: Atmega AVR
-#  - Processor model: atmega2560 
+#  - Processor model: atmega2560
 # -run `make` to build the MCU firmware.
 # -Stop the Klipper service: `sudo service klipper stop`
 # -Flash the MCU: `make flash FLASH_DEVICE=<your port ID>`.
@@ -50,7 +50,7 @@
  position_endstop: 0
  position_max: 760
  homing_speed: 20
- 
+
 [stepper_z]
  step_pin: z_step
  dir_pin: z_dir
@@ -62,7 +62,7 @@
  position_max: 900
  position_min: 0.0
  homing_speed: 5
- 
+
 [extruder]
  step_pin: e1_step
  dir_pin: !e1_dir
@@ -112,10 +112,10 @@
 
 [mcp4451 pot2]
  i2c_address: 46
- wiper_0: 0    	#Goes to E2 driver
- wiper_1: 0  	#Goes to E3 driver
+ wiper_0: 0     #Goes to E2 driver
+ wiper_1: 0     #Goes to E3 driver
  wiper_2: 0     #Goes to E4 driver
- wiper_3: 0		#Goes to E5 driver
+ wiper_3: 0     #Goes to E5 driver
 
 #The Viki2 display is actually ST7565 based, but the UC1701 type works here.
 #[display]
@@ -128,84 +128,84 @@
 
 [board_pins]
 aliases:
-	x_step=PF0,
-	x_dir=PF1,
-	x_enable=PD7,		#All motor enable pins have hardware pullups.
-	x_min_endstop=PE5,
-	x_max_endstop=PE4,
+    x_step=PF0,
+    x_dir=PF1,
+    x_enable=PD7,       #All motor enable pins have hardware pullups.
+    x_min_endstop=PE5,
+    x_max_endstop=PE4,
 
-	y_step=PF6,
-	y_dir=PF7,
-	y_enable=PF2,
-	y_min_endstop=PJ1,
-	y_max_endstop=PJ0,
+    y_step=PF6,
+    y_dir=PF7,
+    y_enable=PF2,
+    y_min_endstop=PJ1,
+    y_max_endstop=PJ0,
 
-	z_step=PL3,
-	z_dir=PL1,
-	z_enable=PK0,
-	z_min_endstop=PD3,
-	z_max_endstop=PD2,
+    z_step=PL3,
+    z_dir=PL1,
+    z_enable=PK0,
+    z_min_endstop=PD3,
+    z_max_endstop=PD2,
 
-	e1_enable=PA2,
-	e1_dir=PA6,
-	e1_step=PA4,
+    e1_enable=PA2,
+    e1_dir=PA6,
+    e1_step=PA4,
 
-	e2_enable=PC7,
-	e2_dir=PC3,
-	e2_step=PC1,
+    e2_enable=PC7,
+    e2_dir=PC3,
+    e2_step=PC1,
 
-	e3_enable=PG1,
-	e3_dir=PA3,
-	e3_step=PA1,
+    e3_enable=PG1,
+    e3_dir=PA3,
+    e3_step=PA1,
 
-	e4_enable=PG0,
-	e4_dir=PA7,
-	e4_step=PA5,
+    e4_enable=PG0,
+    e4_dir=PA7,
+    e4_step=PA5,
 
-	e5_enable=PL7,
-	e5_dir=PC0,
-	e5_step=PL6,
+    e5_enable=PL7,
+    e5_dir=PC0,
+    e5_step=PL6,
 
-	thermistor_bed=PK6,
-	thermistor_0=PK5,
-	thermistor_1=PK7,
-	thermistor_2=PK4,
-	thermistor_3=PK3,
-	thermistor_4=PK2,
-	thermocouple1=PF4,		#Type K
-	thermocouple2=PF5,		#Type K
+    thermistor_bed=PK6,
+    thermistor_0=PK5,
+    thermistor_1=PK7,
+    thermistor_2=PK4,
+    thermistor_3=PK3,
+    thermistor_4=PK2,
+    thermocouple1=PF4,      #Type K
+    thermocouple2=PF5,      #Type K
 
-	hotbed=PH5,
-	hotend_1=PB4,
-	hotend_2=PH6,
-	hotend_3=PH1,
-	hotend_4=PH0,
-	hotend_5=PG5,
-	hotend_6=PE3,
-	hotend_7=PH3,
-	hotend_8=PB5,
+    hotbed=PH5,
+    hotend_1=PB4,
+    hotend_2=PH6,
+    hotend_3=PH1,
+    hotend_4=PH0,
+    hotend_5=PG5,
+    hotend_6=PE3,
+    hotend_7=PH3,
+    hotend_8=PB5,
 
-	sd_card_select=PB0,		#Onboard SD card. Not tested.
-	sd_card_detect=PL0,		#Needs pull-up
-	buzzer=PC4,				#High side of buzzer
-	onboard_led=PB7,		#Not tested.
+    sd_card_select=PB0,     #Onboard SD card. Not tested.
+    sd_card_detect=PL0,     #Needs pull-up
+    buzzer=PC4,             #High side of buzzer
+    onboard_led=PB7,        #Not tested.
 
-	#Pins for the Viki2 LCD. These pins are somewhat arbitrary, but
-	# the below is the standard wiring from the manual.
-	viki2_buzzer=PC4,		#Same as onboard buzzer
-	viki2_lcd_a0=PL5,
-	viki2_lcd_cs=PL4,
-	viki2_enc_a=PA0,
-	viki2_enc_b=PH4,
-	viki2_enc_btn=PG2,
-	viki2_sd_detect=PL0,
-	viki2_sd_cs=PL0,
-	viki2_led_red=PC5,
-	viki2_led_blue=PC2,
+    #Pins for the Viki2 LCD. These pins are somewhat arbitrary, but
+    # the below is the standard wiring from the manual.
+    viki2_buzzer=PC4,       #Same as onboard buzzer
+    viki2_lcd_a0=PL5,
+    viki2_lcd_cs=PL4,
+    viki2_enc_a=PA0,
+    viki2_enc_b=PH4,
+    viki2_enc_btn=PG2,
+    viki2_sd_detect=PL0,
+    viki2_sd_cs=PL0,
+    viki2_led_red=PC5,
+    viki2_led_blue=PC2,
 
-	rx=PE0,					#Attached to USB through a FTDI FT231x
-	tx=PE1,
-	MOSI=PB2,
-	MISO=PB3,
-	SDA=PD1,
-	SCL=PD0,
\ No newline at end of file
+    rx=PE0,                 #Attached to USB through a FTDI FT231x
+    tx=PE1,
+    MOSI=PB2,
+    MISO=PB3,
+    SDA=PD1,
+    SCL=PD0,