{
  "type": "machine",
  "name": "fdm_klipper_common",
  "from": "system",
  "instantiation": "false",
  "inherits": "fdm_machine_common",
  "gcode_flavor": "klipper",
  "machine_max_acceleration_e": ["20000", "20000"],
  "machine_max_acceleration_extruding": ["50000", "50000"],
  "machine_max_acceleration_retracting": ["10000", "10000"],
  "machine_max_acceleration_travel": ["50000", "50000"],
  "machine_max_acceleration_x": ["50000", "50000"],
  "machine_max_acceleration_y": ["50000", "50000"],
  "machine_max_acceleration_z": ["1000", "500"],
  "machine_max_speed_e": ["100", "100"],
  "machine_max_speed_x": ["2000", "2000"],
  "machine_max_speed_y": ["2000", "2000"],
  "machine_max_speed_z": ["15", "15"],
  "machine_max_jerk_e": ["0", "0"],
  "machine_max_jerk_x": ["0", "0"],
  "machine_max_jerk_y": ["0", "0"],
  "machine_max_jerk_z": ["0", "0"],
  "machine_min_extruding_rate": ["0", "0"],
  "machine_min_travel_rate": ["0", "0"],
  "max_layer_height": ["0.32"],
  "min_layer_height": ["0.08"],
  "printable_height": "200",
  "extruder_clearance_radius": "45",
  "extruder_clearance_height_to_rod": "36",
  "extruder_clearance_height_to_lid": "140",
  "printer_settings_id": "",
  "printer_technology": "FFF",
  "printer_variant": "0.4",
  "retraction_minimum_travel": ["1"],
  "retract_before_wipe": ["70%"],
  "retract_when_changing_layer": ["1"],
  "retraction_length": ["0.5"],
  "retract_length_toolchange": ["2"],
  "z_hop": ["0"],
  "retract_restart_extra": ["0"],
  "retract_restart_extra_toolchange": ["0"],
  "retraction_speed": ["30"],
  "deretraction_speed": ["80"],
  "z_lift_type": "NormalLift",
  "silent_mode": "0",
  "single_extruder_multi_material": "1",
  "change_filament_gcode": "",
  "machine_pause_gcode": "M25",
  "wipe": ["1"],
  "default_filament_profile": ["Flashforge Generic ABS"],
  "default_print_profile": "0.20mm Standard @Flashforge AD5M",
  "bed_exclude_area": ["0x0"],
  "machine_start_gcode": "BED_MESH_PROFILE LOAD=default \nM190 S[bed_temperature_initial_layer_single] ;set bed temp \nG28; \nG1 X2 Y2 Z0 F9000  ; move to corner \nM109 S[nozzle_temperature_initial_layer] ; set nozzle temp \nG1 Z0.2 F300 ; raise nozzle to 0.2\nG92 E0.0 ; reset extruder distance position\nG1 X60.0 E9.0 F1000.0 ; intro line\nG1 X100.0 E21.5 F1000.0 ; intro line\nG0 Z2\n\nG92 E0.0 ; reset extruder distance position",
  "machine_end_gcode": "G91; //rel pos\nG1 E-5 f2000\nG1 Z10 F600 ; lift nozzle 10mm/s\nG1 E-29 f600\nM104 S0\nM140 S0 ; turn off bed\n\nM107\nG90\nG0 X117 Y200  F6000; move to back\nM84     ; disable motors\nDSLR_SNAPSHOT\nRSCS_off\n\nexhaustfan_on\nTIMELAPSE_RENDER\n\nG4 P60000 ; //Dwell for 1min\nM107 \nexhaustfan_off\n\nG4 P120000\n\npower_off ; //this is with moonraker",
  "layer_change_gcode": ";DSLR_SNAPSHOT\nTIMELAPSE_TAKE_FRAME",
  "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
  "scan_first_layer": "0",
  "nozzle_type": "undefine",
  "auxiliary_fan": "0"
}