the root cause is a mismatch between the dimensions of flush matrix and the number of extruders
Change-Id: I3a4ca706cb24d9e5d33969b9e6f5b288e71bb8f2
(cherry picked from commit 7399037eaacdfd7d8407667a2e5a097757265254)
This is fix for jira 2061
Layer height is double and may has small difference, which
influence total layer number when support is enabled.
Should use int data and consider EPSION when calculate total
layer number.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I1bb6c89f2afd162d2d7e7dcff4a9d6a00b94dab3
This reverts commit 1e95803df3733021e80241ecf7b88976708f0cf7.
Reason for revert: some model test not good, need to update curve function
Change-Id: I6afd6115d21198f60453d4f507905b6684a65cff
fix enable status of confirm btn in ams settings dlg
Change-Id: I25c11078bb723647fac6370f966c74c807362e21
Signed-off-by: Stone Li <stone.li@bambulab.com>
refine description for ams not connected
Change-Id: Ic4c01e69cfd9385548a497af5c5c3071614067a2
Signed-off-by: Stone Li <stone.li@bambulab.com>
(cherry picked from commit 4158f1e06ed20fa5dd4c3ef412d4c8fab76054a8)
Use tree support to detect if there are sharp tails and so on.
Jira: STUDIO-1898
Change-Id: I148e14ca4024849875133a646a8fdd36c265b2fb
(cherry picked from commit bc74015d45e96e409d34d611876e3a24e289e029)
For pa-cf, the default setting of cooling is
forcing cooling for all outer wall.
And internal tester found that the slowing down by
layer time does not work for outer wall under
this situation.
This is fix for this issue.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I05aaa16d246f5ea6dc1ae9808050e1281646e184
Tree support didn't fill the first layer when the tree is too short
udesk: 0284
Change-Id: I2702b26733e7360445e19847abb48f75f173da4e
(cherry picked from commit e317f9e19fbbfe21efb495e23a8ff78661bfee79)
1. display factor of extrusion calibration
2. add progress to calibration extrusion
3. support ext spool
Change-Id: Ic124a0097f16e6287c09f5f133eea84eeefb4000
Signed-off-by: Stone Li <stone.li@bambulab.com>
Start gcode of P1P is wrong.
This is for github issue #1044
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Id078b7c9020ef773373c3486f74dc51385b9dcc0
1. add gcode command for void printing detection
2. fix the issue that the toolhead is not at excess chute position when
smooth timelapse ends, by adding 2s pause after M991 command.
Jira: STUDIO-1996
Change-Id: I40cf16116e742744cea9bd90969e556a9ea2b2f1
(cherry picked from commit 2fbf7ffe6b1bd8850a76e229ff91750c689721b9)
* fix typo and tooltip
* merge pot po german
* fix more
* merge with bambu master pot
* fix po to Softfever
* fix
* build new Softfever pot mege with xx.po
* enable hints in german again
