fix 1.7dev Language de ru es (#2000)

localization/i18n/nl/OrcaSlicer_nl.po

@@ -2,7 +2,7 @@ msgid ""
 msgstr ""
 "Project-Id-Version: Orca Slicer\n"
 "Report-Msgid-Bugs-To: \n"
-"POT-Creation-Date: 2023-08-31 21:45+0800\n"
+"POT-Creation-Date: 2023-09-04 11:33+0200\n"
 "Language: nl\n"
 "MIME-Version: 1.0\n"
 "Content-Type: text/plain; charset=UTF-8\n"
@@ -5644,8 +5644,8 @@ msgstr ""
 msgid ""
 "When recording timelapse without toolhead, it is recommended to add a "
 "\"Timelapse Wipe Tower\" \n"
-"by right-click the empty position of build plate and choose \"Add Primitive"
-"\"->\"Timelapse Wipe Tower\"."
+"by right-click the empty position of build plate and choose \"Add "
+"Primitive\"->\"Timelapse Wipe Tower\"."
 msgstr ""
 "Bij het opnemen van timelapse zonder toolhead is het aan te raden om een "
 "„Timelapse Wipe Tower” toe te voegen \n"
@@ -6949,6 +6949,21 @@ msgid ""
 msgstr ""
 "Een prime toren vereist dat support dezelfde laaghoogte heeft als het object."
 
+msgid ""
+"Organic support tree tip diameter must not be smaller than support material "
+"extrusion width."
+msgstr ""
+
+msgid ""
+"Organic support branch diameter must not be smaller than 2x support material "
+"extrusion width."
+msgstr ""
+
+msgid ""
+"Organic support branch diameter must not be smaller than support tree tip "
+"diameter."
+msgstr ""
+
 msgid ""
 "Support enforcers are used but support is not enabled. Please enable support."
 msgstr ""
@@ -8179,10 +8194,10 @@ msgstr "Volledige snelheid op laag"
 
 msgid ""
 "Fan speed will be ramped up linearly from zero at layer "
-"\"close_fan_the_first_x_layers\" to maximum at layer \"full_fan_speed_layer"
-"\". \"full_fan_speed_layer\" will be ignored if lower than "
-"\"close_fan_the_first_x_layers\", in which case the fan will be running at "
-"maximum allowed speed at layer \"close_fan_the_first_x_layers\" + 1."
+"\"close_fan_the_first_x_layers\" to maximum at layer "
+"\"full_fan_speed_layer\". \"full_fan_speed_layer\" will be ignored if lower "
+"than \"close_fan_the_first_x_layers\", in which case the fan will be running "
+"at maximum allowed speed at layer \"close_fan_the_first_x_layers\" + 1."
 msgstr ""
 
 msgid "Support interface fan speed"
@@ -9373,6 +9388,9 @@ msgstr "Tree Strong"
 msgid "Tree Hybrid"
 msgstr "Tree Hybrid"
 
+msgid "Organic"
+msgstr ""
+
 msgid "Independent support layer height"
 msgstr "Onafhankelijke support laaghoogte"
 
@@ -9407,6 +9425,16 @@ msgstr ""
 "support mogen maken. Als de hoek wordt vergroot, kunnen de uitlopen meer "
 "horizontaal worden geprint, waardoor ze verder kunnen reiken."
 
+msgid "Preferred Branch Angle"
+msgstr ""
+
+#. TRN PrintSettings: "Organic supports" > "Preferred Branch Angle"
+msgid ""
+"The preferred angle of the branches, when they do not have to avoid the "
+"model. Use a lower angle to make them more vertical and more stable. Use a "
+"higher angle for branches to merge faster."
+msgstr ""
+
 msgid "Tree support branch distance"
 msgstr "Tree support tak-afstand"
 
@@ -9416,6 +9444,18 @@ msgstr ""
 "Deze instelling bepaald de afstand tussen naastliggende tree support "
 "knooppunten."
 
+msgid "Branch Density"
+msgstr ""
+
+#. TRN PrintSettings: "Organic supports" > "Branch Density"
+msgid ""
+"Adjusts the density of the support structure used to generate the tips of "
+"the branches. A higher value results in better overhangs but the supports "
+"are harder to remove, thus it is recommended to enable top support "
+"interfaces instead of a high branch density value if dense interfaces are "
+"needed."
+msgstr ""
+
 msgid "Adaptive layer height"
 msgstr "Adaptieve laaghoogte"
 
@@ -9438,12 +9478,41 @@ msgstr "Tree support brim width"
 msgid "Distance from tree branch to the outermost brim line"
 msgstr ""
 
+msgid "Tip Diameter"
+msgstr ""
+
+#. TRN PrintSettings: "Organic supports" > "Tip Diameter"
+msgid "Branch tip diameter for organic supports."
+msgstr ""
+
 msgid "Tree support branch diameter"
 msgstr "Tree support diameter van de takken"
 
 msgid "This setting determines the initial diameter of support nodes."
 msgstr "Deze instelling bepaalt de initiële diameter van support knooppunten."
 
+#. TRN PrintSettings: #lmFIXME
+msgid "Branch Diameter Angle"
+msgstr ""
+
+#. TRN PrintSettings: "Organic supports" > "Branch Diameter Angle"
+msgid ""
+"The angle of the branches' diameter as they gradually become thicker towards "
+"the bottom. An angle of 0 will cause the branches to have uniform thickness "
+"over their length. A bit of an angle can increase stability of the organic "
+"support."
+msgstr ""
+
+msgid "Branch Diameter with double walls"
+msgstr ""
+
+#. TRN PrintSettings: "Organic supports" > "Branch Diameter"
+msgid ""
+"Branches with area larger than the area of a circle of this diameter will be "
+"printed with double walls for stability. Set this value to zero for no "
+"double walls."
+msgstr ""
+
 msgid "Tree support wall loops"
 msgstr "Tree support wand lussen"
 
@@ -9767,6 +9836,15 @@ msgstr ""
 "wandbreedte. Dit wordt uitgedrukt als een percentage ten opzichte van de "
 "diameter van het mondstuk"
 
+msgid "First layer minimum wall width"
+msgstr ""
+
+msgid ""
+"The minimum wall width that should be used for the first layer is "
+"recommended to be set to the same size as the nozzle. This adjustment is "
+"expected to enhance adhesion."
+msgstr ""
+
 msgid "Minimum wall width"
 msgstr "Minimale wandbreedte"