mirror of
https://github.com/SoftFever/OrcaSlicer.git
synced 2025-07-07 06:57:36 -06:00
IS Calib - Use default Filament MVS To fix #9439 added a comment in wiki and remove Max Volumetric Speed overload. Co-authored-by: Rodrigo <162915171+RF47@users.noreply.github.com>
This commit is contained in:
parent
6423d521cd
commit
9565f39c7a
3 changed files with 44 additions and 43 deletions
|
@ -176,7 +176,9 @@ Ussualy the recommended values modes are ``MZV`` or ``EI`` for Delta printers.
|
||||||
1. Pre-requisites:
|
1. Pre-requisites:
|
||||||
1. In OrcaSlicer, set:
|
1. In OrcaSlicer, set:
|
||||||
1. Acceleration high enough to trigger ringing (e.g., 2000 mm/s²).
|
1. Acceleration high enough to trigger ringing (e.g., 2000 mm/s²).
|
||||||
2. Speed high enough to trigger ringing (e.g., 100 mm/s).
|
2. Speed high enough to trigger ringing (e.g., 200 mm/s).
|
||||||
|
> [!NOTE]
|
||||||
|
> These settings depend on your printer's motion ability and the filament's max volumetric speed. If you can't reach speeds that cause ringing, try increasing the filament's max volumetric speed (avoid materials below 10 mm³/s).
|
||||||
3. Jerk [Klipper Square Corner Velocity](https://www.klipper3d.org/Kinematics.html?h=square+corner+velocity#look-ahead) to 5 or a high value (e.g., 20).
|
3. Jerk [Klipper Square Corner Velocity](https://www.klipper3d.org/Kinematics.html?h=square+corner+velocity#look-ahead) to 5 or a high value (e.g., 20).
|
||||||
2. In printer settigs:
|
2. In printer settigs:
|
||||||
1. Set the Shaper Type to ``MZV`` or ``EI``.
|
1. Set the Shaper Type to ``MZV`` or ``EI``.
|
||||||
|
@ -223,8 +225,10 @@ ZV Input Shaping introduces an anti-vibration signal into the stepper motion for
|
||||||
1. Pre-requisites:
|
1. Pre-requisites:
|
||||||
1. In OrcaSlicer, set:
|
1. In OrcaSlicer, set:
|
||||||
1. Acceleration high enough to trigger ringing (e.g., 2000 mm/s²).
|
1. Acceleration high enough to trigger ringing (e.g., 2000 mm/s²).
|
||||||
2. Speed high enough to trigger ringing (e.g., 100 mm/s).
|
2. Speed high enough to trigger ringing (e.g., 200 mm/s).
|
||||||
3. Jerk
|
> [!NOTE]
|
||||||
|
> These settings depend on your printer's motion ability and the filament's max volumetric speed. If you can't reach speeds that cause ringing, try increasing the filament's max volumetric speed (avoid materials below 10 mm³/s).
|
||||||
|
4. Jerk
|
||||||
1. If using [Classic Jerk](https://marlinfw.org/docs/configuration/configuration.html#jerk-) use a high value (e.g., 20).
|
1. If using [Classic Jerk](https://marlinfw.org/docs/configuration/configuration.html#jerk-) use a high value (e.g., 20).
|
||||||
2. If using [Junction Deviation](https://marlinfw.org/docs/features/junction_deviation.html) (new Marlin default mode) this test will use 0.25 (high enough to most printers).
|
2. If using [Junction Deviation](https://marlinfw.org/docs/features/junction_deviation.html) (new Marlin default mode) this test will use 0.25 (high enough to most printers).
|
||||||
2. Use an opaque, high-gloss filament to make the ringing more visible.
|
2. Use an opaque, high-gloss filament to make the ringing more visible.
|
||||||
|
|
Before Width: | Height: | Size: 8.7 KiB After Width: | Height: | Size: 8.7 KiB |
|
@ -10186,7 +10186,6 @@ void Plater::calib_VFA(const Calib_Params& params)
|
||||||
auto print_config = &wxGetApp().preset_bundle->prints.get_edited_preset().config;
|
auto print_config = &wxGetApp().preset_bundle->prints.get_edited_preset().config;
|
||||||
auto filament_config = &wxGetApp().preset_bundle->filaments.get_edited_preset().config;
|
auto filament_config = &wxGetApp().preset_bundle->filaments.get_edited_preset().config;
|
||||||
filament_config->set_key_value("slow_down_layer_time", new ConfigOptionFloats { 0.0 });
|
filament_config->set_key_value("slow_down_layer_time", new ConfigOptionFloats { 0.0 });
|
||||||
filament_config->set_key_value("filament_max_volumetric_speed", new ConfigOptionFloats { 200 });
|
|
||||||
print_config->set_key_value("enable_overhang_speed", new ConfigOptionBool { false });
|
print_config->set_key_value("enable_overhang_speed", new ConfigOptionBool { false });
|
||||||
print_config->set_key_value("timelapse_type", new ConfigOptionEnum<TimelapseType>(tlTraditional));
|
print_config->set_key_value("timelapse_type", new ConfigOptionEnum<TimelapseType>(tlTraditional));
|
||||||
print_config->set_key_value("wall_loops", new ConfigOptionInt(1));
|
print_config->set_key_value("wall_loops", new ConfigOptionInt(1));
|
||||||
|
@ -10233,7 +10232,6 @@ void Plater::calib_input_shaping_freq(const Calib_Params& params)
|
||||||
filament_config->set_key_value("slow_down_layer_time", new ConfigOptionFloats { 0.0 });
|
filament_config->set_key_value("slow_down_layer_time", new ConfigOptionFloats { 0.0 });
|
||||||
filament_config->set_key_value("slow_down_min_speed", new ConfigOptionFloats { 0.0 });
|
filament_config->set_key_value("slow_down_min_speed", new ConfigOptionFloats { 0.0 });
|
||||||
filament_config->set_key_value("slow_down_for_layer_cooling", new ConfigOptionBools{false});
|
filament_config->set_key_value("slow_down_for_layer_cooling", new ConfigOptionBools{false});
|
||||||
filament_config->set_key_value("filament_max_volumetric_speed", new ConfigOptionFloats { 200 });
|
|
||||||
filament_config->set_key_value("enable_pressure_advance", new ConfigOptionBools {false });
|
filament_config->set_key_value("enable_pressure_advance", new ConfigOptionBools {false });
|
||||||
filament_config->set_key_value("pressure_advance", new ConfigOptionFloats { 0.0 });
|
filament_config->set_key_value("pressure_advance", new ConfigOptionFloats { 0.0 });
|
||||||
print_config->set_key_value("layer_height", new ConfigOptionFloat(0.2));
|
print_config->set_key_value("layer_height", new ConfigOptionFloat(0.2));
|
||||||
|
@ -10280,7 +10278,6 @@ void Plater::calib_input_shaping_damp(const Calib_Params& params)
|
||||||
filament_config->set_key_value("slow_down_layer_time", new ConfigOptionFloats { 0.0 });
|
filament_config->set_key_value("slow_down_layer_time", new ConfigOptionFloats { 0.0 });
|
||||||
filament_config->set_key_value("slow_down_min_speed", new ConfigOptionFloats { 0.0 });
|
filament_config->set_key_value("slow_down_min_speed", new ConfigOptionFloats { 0.0 });
|
||||||
filament_config->set_key_value("slow_down_for_layer_cooling", new ConfigOptionBools{false});
|
filament_config->set_key_value("slow_down_for_layer_cooling", new ConfigOptionBools{false});
|
||||||
filament_config->set_key_value("filament_max_volumetric_speed", new ConfigOptionFloats { 200 });
|
|
||||||
filament_config->set_key_value("enable_pressure_advance", new ConfigOptionBools{false});
|
filament_config->set_key_value("enable_pressure_advance", new ConfigOptionBools{false});
|
||||||
filament_config->set_key_value("pressure_advance", new ConfigOptionFloats{0.0});
|
filament_config->set_key_value("pressure_advance", new ConfigOptionFloats{0.0});
|
||||||
print_config->set_key_value("layer_height", new ConfigOptionFloat(0.2));
|
print_config->set_key_value("layer_height", new ConfigOptionFloat(0.2));
|
||||||
|
|
Loading…
Add table
Add a link
Reference in a new issue