diff --git a/resources/profiles/BBL/machine/fdm_bbl_3dp_001_common.json b/resources/profiles/BBL/machine/fdm_bbl_3dp_001_common.json index 1eaeafadf1..c217e13022 100644 --- a/resources/profiles/BBL/machine/fdm_bbl_3dp_001_common.json +++ b/resources/profiles/BBL/machine/fdm_bbl_3dp_001_common.json @@ -45,8 +45,8 @@ "5000" ], "machine_max_acceleration_travel": [ - "9000", - "9000" + "20000", + "20000" ], "machine_max_acceleration_x": [ "20000", diff --git a/resources/profiles/OrcaArena/machine/fdm_bbl_3dp_001_common.json b/resources/profiles/OrcaArena/machine/fdm_bbl_3dp_001_common.json index 97819d779d..50aad39db8 100644 --- a/resources/profiles/OrcaArena/machine/fdm_bbl_3dp_001_common.json +++ b/resources/profiles/OrcaArena/machine/fdm_bbl_3dp_001_common.json @@ -38,8 +38,8 @@ "5000" ], "machine_max_acceleration_travel": [ - "9000", - "9000" + "20000", + "20000" ], "machine_max_acceleration_x": [ "20000", diff --git a/resources/profiles/Prusa/machine/Prusa MK4 0.4 nozzle.json b/resources/profiles/Prusa/machine/Prusa MK4 0.4 nozzle.json index 08b1852b8b..b36e734e21 100644 --- a/resources/profiles/Prusa/machine/Prusa MK4 0.4 nozzle.json +++ b/resources/profiles/Prusa/machine/Prusa MK4 0.4 nozzle.json @@ -47,6 +47,10 @@ "200", "200" ], + "machine_max_acceleration_travel": [ + "4000", + "4000" + ], "host_type": "prusalink", "printable_height": "220", "machine_end_gcode": "{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X241 Y170 F3600 ; park\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+23, max_print_height)} F300 ; Move print head up{endif}\nG4 ; wait\nM572 S0 ; reset PA\nM593 X T2 F0 ; disable IS\nM593 Y T2 F0 ; disable IS\nM84 X Y E ; disable motors\n; max_layer_z = [max_layer_z]", diff --git a/resources/profiles/TwoTrees/machine/fdm_klipper_common.json b/resources/profiles/TwoTrees/machine/fdm_klipper_common.json index b85fea785f..491fef0082 100644 --- a/resources/profiles/TwoTrees/machine/fdm_klipper_common.json +++ b/resources/profiles/TwoTrees/machine/fdm_klipper_common.json @@ -19,8 +19,8 @@ "5000" ], "machine_max_acceleration_travel": [ - "9000", - "9000" + "20000", + "20000" ], "machine_max_acceleration_x": [ "9000", diff --git a/resources/profiles/UltiMaker/machine/UltiMaker 2 0.4 nozzle.json b/resources/profiles/UltiMaker/machine/UltiMaker 2 0.4 nozzle.json index 9404ebfc9b..c7166bc030 100644 --- a/resources/profiles/UltiMaker/machine/UltiMaker 2 0.4 nozzle.json +++ b/resources/profiles/UltiMaker/machine/UltiMaker 2 0.4 nozzle.json @@ -28,8 +28,8 @@ "1500" ], "machine_max_acceleration_travel": [ - "500", - "500" + "3000", + "3000" ], "machine_max_acceleration_x": [ "3000", diff --git a/resources/profiles/Vivedino/machine/fdm_klipper_common.json b/resources/profiles/Vivedino/machine/fdm_klipper_common.json index 98b753942d..d7a84deba5 100644 --- a/resources/profiles/Vivedino/machine/fdm_klipper_common.json +++ b/resources/profiles/Vivedino/machine/fdm_klipper_common.json @@ -18,8 +18,8 @@ "5000" ], "machine_max_acceleration_travel": [ - "9000", - "9000" + "20000", + "20000" ], "machine_max_acceleration_x": [ "20000", diff --git a/resources/profiles/Vivedino/machine/fdm_rrf_common.json b/resources/profiles/Vivedino/machine/fdm_rrf_common.json index e4cff40f43..740146688c 100644 --- a/resources/profiles/Vivedino/machine/fdm_rrf_common.json +++ b/resources/profiles/Vivedino/machine/fdm_rrf_common.json @@ -18,8 +18,8 @@ "5000" ], "machine_max_acceleration_travel": [ - "9000", - "9000" + "20000", + "20000" ], "machine_max_acceleration_x": [ "20000", diff --git a/resources/profiles/Voron/machine/fdm_klipper_common.json b/resources/profiles/Voron/machine/fdm_klipper_common.json index 6a3b00a6b8..4b16b80ad9 100644 --- a/resources/profiles/Voron/machine/fdm_klipper_common.json +++ b/resources/profiles/Voron/machine/fdm_klipper_common.json @@ -18,8 +18,8 @@ "5000" ], "machine_max_acceleration_travel": [ - "9000", - "9000" + "20000", + "20000" ], "machine_max_acceleration_x": [ "20000", diff --git a/src/libslic3r/GCode.cpp b/src/libslic3r/GCode.cpp index 056ab63814..1fc21b5a61 100644 --- a/src/libslic3r/GCode.cpp +++ b/src/libslic3r/GCode.cpp @@ -2066,7 +2066,7 @@ void GCode::_do_export(Print& print, GCodeOutputStream &file, ThumbnailsGenerato if (print.calib_params().mode == CalibMode::Calib_PA_Line) { std::string gcode; if ((m_config.default_acceleration.value > 0 && m_config.outer_wall_acceleration.value > 0)) { - gcode += m_writer.set_acceleration((unsigned int)floor(m_config.outer_wall_acceleration.value + 0.5)); + gcode += m_writer.set_print_acceleration((unsigned int)floor(m_config.outer_wall_acceleration.value + 0.5)); } if (m_config.default_jerk.value > 0) { @@ -3120,7 +3120,7 @@ GCode::LayerResult GCode::process_layer( //BBS if (first_layer) { if (m_config.default_acceleration.value > 0 && m_config.initial_layer_acceleration.value > 0) { - gcode += m_writer.set_acceleration((unsigned int)floor(m_config.initial_layer_acceleration.value + 0.5)); + gcode += m_writer.set_print_acceleration((unsigned int)floor(m_config.initial_layer_acceleration.value + 0.5)); } if (m_config.default_jerk.value > 0 && m_config.initial_layer_jerk.value > 0) { @@ -3147,7 +3147,7 @@ GCode::LayerResult GCode::process_layer( } // BBS: reset acceleration at sencond layer if (m_config.default_acceleration.value > 0 && m_config.initial_layer_acceleration.value > 0) { - gcode += m_writer.set_acceleration((unsigned int)floor(m_config.default_acceleration.value + 0.5)); + gcode += m_writer.set_print_acceleration((unsigned int)floor(m_config.default_acceleration.value + 0.5)); } if (m_config.default_jerk.value > 0 && m_config.initial_layer_jerk.value > 0) { @@ -4158,7 +4158,7 @@ std::string GCode::_extrude(const ExtrusionPath &path, std::string description, } else { acceleration = m_config.default_acceleration.value; } - gcode += m_writer.set_acceleration((unsigned int)floor(acceleration + 0.5)); + gcode += m_writer.set_print_acceleration((unsigned int)floor(acceleration + 0.5)); } // adjust X Y jerk @@ -4613,14 +4613,14 @@ std::string GCode::travel_to(const Point &point, ExtrusionRole role, std::string // SoftFever if (this->on_first_layer()) { if (m_config.default_acceleration.value > 0 && m_config.initial_layer_acceleration.value > 0) { - gcode += m_writer.set_acceleration((unsigned int)floor(m_config.initial_layer_acceleration.value + 0.5)); + gcode += m_writer.set_travel_acceleration((unsigned int)floor(m_config.initial_layer_acceleration.value + 0.5)); } if (m_config.default_jerk.value > 0 && m_config.initial_layer_jerk.value > 0) { gcode += m_writer.set_jerk_xy(m_config.initial_layer_jerk.value); } } else { if (m_config.default_acceleration.value > 0 && m_config.travel_acceleration.value > 0) { - gcode += m_writer.set_acceleration((unsigned int)floor(m_config.travel_acceleration.value + 0.5)); + gcode += m_writer.set_travel_acceleration((unsigned int)floor(m_config.travel_acceleration.value + 0.5)); } if (m_config.default_jerk.value > 0 && m_config.travel_jerk.value > 0) { diff --git a/src/libslic3r/GCode/WipeTower.cpp b/src/libslic3r/GCode/WipeTower.cpp index fd51f7cf7f..2d6d6d765f 100644 --- a/src/libslic3r/GCode/WipeTower.cpp +++ b/src/libslic3r/GCode/WipeTower.cpp @@ -418,36 +418,30 @@ public: // Let the firmware back up the active speed override value. WipeTowerWriter& speed_override_backup() { - // BBS: BBL machine don't support speed backup -#if 0 + // This is only supported by Prusa at this point (https://github.com/prusa3d/PrusaSlicer/issues/3114) if (m_gcode_flavor == gcfMarlinLegacy || m_gcode_flavor == gcfMarlinFirmware) m_gcode += "M220 B\n"; -#endif return *this; } // Let the firmware restore the active speed override value. WipeTowerWriter& speed_override_restore() { - // BBS: BBL machine don't support speed restore -#if 0 if (m_gcode_flavor == gcfMarlinLegacy || m_gcode_flavor == gcfMarlinFirmware) m_gcode += "M220 R\n"; -#endif return *this; } // Set digital trimpot motor WipeTowerWriter& set_extruder_trimpot(int current) { - // BBS: don't control trimpot -#if 0 + if (m_gcode_flavor == gcfKlipper) + return *this; if (m_gcode_flavor == gcfRepRapSprinter || m_gcode_flavor == gcfRepRapFirmware) m_gcode += "M906 E"; else m_gcode += "M907 E"; m_gcode += std::to_string(current) + "\n"; -#endif return *this; } diff --git a/src/libslic3r/GCodeWriter.cpp b/src/libslic3r/GCodeWriter.cpp index 4d9dd3fefb..7a5b8e45c5 100644 --- a/src/libslic3r/GCodeWriter.cpp +++ b/src/libslic3r/GCodeWriter.cpp @@ -30,6 +30,10 @@ void GCodeWriter::apply_print_config(const PrintConfig &print_config) bool use_mach_limits = print_config.gcode_flavor.value == gcfMarlinLegacy || print_config.gcode_flavor.value == gcfMarlinFirmware || print_config.gcode_flavor.value == gcfKlipper || print_config.gcode_flavor.value == gcfRepRapFirmware; m_max_acceleration = std::lrint(use_mach_limits ? print_config.machine_max_acceleration_extruding.values.front() : 0); + m_max_travel_acceleration = static_cast( + std::round((use_mach_limits && supports_separate_travel_acceleration(print_config.gcode_flavor.value)) ? + print_config.machine_max_acceleration_travel.values.front() : + 0)); m_max_jerk = std::lrint( use_mach_limits ? std::min(print_config.machine_max_jerk_x.values.front(), print_config.machine_max_jerk_y.values.front()) : 0); m_max_jerk_z = print_config.machine_max_jerk_z.values.front(); @@ -153,44 +157,40 @@ std::string GCodeWriter::set_bed_temperature(int temperature, bool wait) return gcode.str(); } -std::string GCodeWriter::set_acceleration(unsigned int acceleration) +// copied from PrusaSlicer +std::string GCodeWriter::set_acceleration_internal(Acceleration type, unsigned int acceleration) { // Clamp the acceleration to the allowed maximum. - if (m_max_acceleration > 0 && acceleration > m_max_acceleration) + if (type == Acceleration::Print && m_max_acceleration > 0 && acceleration > m_max_acceleration) acceleration = m_max_acceleration; + if (type == Acceleration::Travel && m_max_travel_acceleration > 0 && acceleration > m_max_travel_acceleration) + acceleration = m_max_travel_acceleration; - if (acceleration == 0 || acceleration == m_last_acceleration) + // Are we setting travel acceleration for a flavour that supports separate travel and print acc? + bool separate_travel = (type == Acceleration::Travel && supports_separate_travel_acceleration(this->config.gcode_flavor)); + + auto& last_value = separate_travel ? m_last_travel_acceleration : m_last_acceleration ; + if (acceleration == 0 || acceleration == last_value) return std::string(); - m_last_acceleration = acceleration; + last_value = acceleration; std::ostringstream gcode; - if (FLAVOR_IS(gcfRepetier)) { - // M201: Set max printing acceleration - gcode << "M201 X" << acceleration << " Y" << acceleration; - //BBS - if (GCodeWriter::full_gcode_comment) gcode << " ; adjust acceleration"; - gcode << "\n"; - // M202: Set max travel acceleration - gcode << "M202 X" << acceleration << " Y" << acceleration; - } else if (FLAVOR_IS(gcfRepRapFirmware)) { - // M204: Set default acceleration - gcode << "M204 P" << acceleration; - } else if (FLAVOR_IS(gcfMarlinFirmware)) { - // This is new MarlinFirmware with separated print/retraction/travel acceleration. - // Use M204 P, we don't want to override travel acc by M204 S (which is deprecated anyway). - gcode << "M204 P" << acceleration; - } else if (FLAVOR_IS(gcfKlipper)) { + if (FLAVOR_IS(gcfRepetier)) + gcode << (separate_travel ? "M202 X" : "M201 X") << acceleration << " Y" << acceleration; + else if (FLAVOR_IS(gcfRepRapFirmware) || FLAVOR_IS(gcfMarlinFirmware)) + gcode << (separate_travel ? "M204 T" : "M204 P") << acceleration; + else if (FLAVOR_IS(gcfKlipper)) { gcode << "SET_VELOCITY_LIMIT ACCEL=" << acceleration; if (this->config.accel_to_decel_enable) { gcode << " ACCEL_TO_DECEL=" << acceleration * this->config.accel_to_decel_factor / 100; if (GCodeWriter::full_gcode_comment) gcode << " ; adjust ACCEL_TO_DECEL"; } - } else + } + else gcode << "M204 S" << acceleration; - //BBS if (GCodeWriter::full_gcode_comment) gcode << " ; adjust acceleration"; gcode << "\n"; diff --git a/src/libslic3r/GCodeWriter.hpp b/src/libslic3r/GCodeWriter.hpp index 8283dac7e0..0e85b36274 100644 --- a/src/libslic3r/GCodeWriter.hpp +++ b/src/libslic3r/GCodeWriter.hpp @@ -19,7 +19,7 @@ public: GCodeWriter() : multiple_extruders(false), m_extruder(nullptr), m_single_extruder_multi_material(false), - m_last_acceleration(0), m_max_acceleration(0), + m_last_acceleration(0), m_max_acceleration(0),m_last_travel_acceleration(0), m_max_travel_acceleration(0), m_last_jerk(0), m_max_jerk(0), /*m_last_bed_temperature(0), */m_last_bed_temperature_reached(true), m_lifted(0), @@ -45,7 +45,8 @@ public: std::string postamble() const; std::string set_temperature(unsigned int temperature, bool wait = false, int tool = -1) const; std::string set_bed_temperature(int temperature, bool wait = false); - std::string set_acceleration(unsigned int acceleration); + std::string set_print_acceleration(unsigned int acceleration) { return set_acceleration_internal(Acceleration::Print, acceleration); } + std::string set_travel_acceleration(unsigned int acceleration) { return set_acceleration_internal(Acceleration::Travel, acceleration); } std::string set_jerk_xy(double jerk); std::string set_pressure_advance(double pa) const; std::string reset_e(bool force = false); @@ -116,6 +117,9 @@ public: bool m_single_extruder_multi_material; Extruder* m_extruder; unsigned int m_last_acceleration; + unsigned int m_last_travel_acceleration; + unsigned int m_max_travel_acceleration; + // Limit for setting the acceleration, to respect the machine limits set for the Marlin firmware. // If set to zero, the limit is not in action. unsigned int m_max_acceleration; @@ -154,9 +158,16 @@ public: double m_current_speed; bool m_is_first_layer = true; + enum class Acceleration { + Travel, + Print + }; + std::string _travel_to_z(double z, const std::string &comment); std::string _spiral_travel_to_z(double z, const Vec2d &ij_offset, const std::string &comment); std::string _retract(double length, double restart_extra, const std::string &comment); + std::string set_acceleration_internal(Acceleration type, unsigned int acceleration); + }; class GCodeFormatter { diff --git a/src/libslic3r/PrintConfig.cpp b/src/libslic3r/PrintConfig.cpp index cf0724c998..c8fa95add4 100644 --- a/src/libslic3r/PrintConfig.cpp +++ b/src/libslic3r/PrintConfig.cpp @@ -2321,11 +2321,11 @@ void PrintConfigDef::init_fff_params() def = this->add("machine_max_acceleration_travel", coFloats); def->full_label = L("Maximum acceleration for travel"); def->category = L("Machine limits"); - def->tooltip = L("Maximum acceleration for travel (M204 T)"); + def->tooltip = L("Maximum acceleration for travel (M204 T), it only applies to Marlin 2"); def->sidetext = L("mm/s²"); def->min = 0; def->readonly = false; - def->mode = comDevelop; + def->mode = comAdvanced; def->set_default_value(new ConfigOptionFloats{ 1500., 1250. }); def = this->add("fan_max_speed", coInts); diff --git a/src/slic3r/GUI/PrintHostDialogs.cpp b/src/slic3r/GUI/PrintHostDialogs.cpp index 9dd9f115d3..338b60eae0 100644 --- a/src/slic3r/GUI/PrintHostDialogs.cpp +++ b/src/slic3r/GUI/PrintHostDialogs.cpp @@ -118,15 +118,15 @@ PrintHostSendDialog::PrintHostSendDialog(const fs::path &path, PrintHostPostUplo }); txt_filename->SetFocus(); - if (post_actions.has(PrintHostPostUploadAction::QueuePrint)) { - auto* btn_print = add_button(wxID_ADD, false, _L("Upload to Queue")); - btn_print->Bind(wxEVT_BUTTON, [this, validate_path](wxCommandEvent&) { - if (validate_path(txt_filename->GetValue())) { - post_upload_action = PrintHostPostUploadAction::QueuePrint; - EndDialog(wxID_OK); - } - }); - } + // if (post_actions.has(PrintHostPostUploadAction::QueuePrint)) { + // auto* btn_print = add_button(wxID_ADD, false, _L("Upload to Queue")); + // btn_print->Bind(wxEVT_BUTTON, [this, validate_path](wxCommandEvent&) { + // if (validate_path(txt_filename->GetValue())) { + // post_upload_action = PrintHostPostUploadAction::QueuePrint; + // EndDialog(wxID_OK); + // } + // }); + // } if (post_actions.has(PrintHostPostUploadAction::StartPrint)) { auto* btn_print = add_button(wxID_YES, false, _L("Upload and Print")); @@ -138,18 +138,18 @@ PrintHostSendDialog::PrintHostSendDialog(const fs::path &path, PrintHostPostUplo }); } - if (post_actions.has(PrintHostPostUploadAction::StartSimulation)) { - // Using wxID_MORE as a button identifier to be different from the other buttons, wxID_MORE has no other meaning here. - auto* btn_simulate = add_button(wxID_MORE, false, _L("Upload and Simulate")); - btn_simulate->Bind(wxEVT_BUTTON, [this, validate_path](wxCommandEvent&) { - if (validate_path(txt_filename->GetValue())) { - post_upload_action = PrintHostPostUploadAction::StartSimulation; - EndDialog(wxID_OK); - } - }); - } + // if (post_actions.has(PrintHostPostUploadAction::StartSimulation)) { + // // Using wxID_MORE as a button identifier to be different from the other buttons, wxID_MORE has no other meaning here. + // auto* btn_simulate = add_button(wxID_MORE, false, _L("Upload and Simulate")); + // btn_simulate->Bind(wxEVT_BUTTON, [this, validate_path](wxCommandEvent&) { + // if (validate_path(txt_filename->GetValue())) { + // post_upload_action = PrintHostPostUploadAction::StartSimulation; + // EndDialog(wxID_OK); + // } + // }); + // } - add_button(wxID_CANCEL); + add_button(wxID_CANCEL,false, L("Cancel")); finalize(); #ifdef __linux__ diff --git a/src/slic3r/GUI/Tab.cpp b/src/slic3r/GUI/Tab.cpp index 73f9b101e3..3b290fde85 100644 --- a/src/slic3r/GUI/Tab.cpp +++ b/src/slic3r/GUI/Tab.cpp @@ -3,6 +3,7 @@ #include "Tab.hpp" #include "PresetHints.hpp" #include "libslic3r/PresetBundle.hpp" +#include "libslic3r/PrintConfig.hpp" #include "libslic3r/Utils.hpp" #include "libslic3r/Model.hpp" #include "libslic3r/GCode/GCodeProcessor.hpp" @@ -3140,7 +3141,7 @@ void TabPrinter::build_fff() // optgroup->append_single_option_line("spaghetti_detector"); optgroup->append_single_option_line("machine_load_filament_time"); optgroup->append_single_option_line("machine_unload_filament_time"); - + optgroup = page->new_optgroup(L("Cooling Fan")); Line line = Line{ L("Fan speed-up time"), optgroup->get_option("fan_speedup_time").opt.tooltip }; line.append_option(optgroup->get_option("fan_speedup_time")); @@ -3389,10 +3390,9 @@ PageShp TabPrinter::build_kinematics_page() } append_option_line(optgroup, "machine_max_acceleration_extruding"); append_option_line(optgroup, "machine_max_acceleration_retracting"); - if (m_supports_travel_acceleration) - append_option_line(optgroup, "machine_max_acceleration_travel"); + append_option_line(optgroup, "machine_max_acceleration_travel"); - optgroup = page->new_optgroup(L("Jerk limitation")); + optgroup = page->new_optgroup(L("Jerk limitation")); for (const std::string &axis : axes) { append_option_line(optgroup, "machine_max_jerk_" + axis); } @@ -3718,14 +3718,6 @@ void TabPrinter::toggle_options() if (m_active_page->title() == "Basic information") { toggle_option("single_extruder_multi_material", have_multiple_extruders); - auto flavor = m_config->option>("gcode_flavor")->value; - bool is_marlin_flavor = flavor == gcfMarlinLegacy || flavor == gcfMarlinFirmware; - // Disable silent mode for non-marlin firmwares. - toggle_option("silent_mode", is_marlin_flavor); - //BBS: extruder clearance of BBL printer can't be edited. - //for (auto el : { "extruder_clearance_radius", "extruder_clearance_height_to_rod", "extruder_clearance_height_to_lid" }) - // toggle_option(el, !is_BBL_printer); - // SoftFever: hide BBL specific settings for (auto el : {"scan_first_layer", "machine_load_filament_time", "machine_unload_filament_time", "bbl_calib_mark_logo"}) @@ -3805,16 +3797,15 @@ void TabPrinter::toggle_options() toggle_option("retract_restart_extra_toolchange", have_multiple_extruders && toolchange_retraction, i); } - //auto gcf = m_config->option>("gcode_flavor")->value; - //if (m_active_page->title() == "Motion ability") { - // assert(gcf == gcfMarlinLegacy || gcf == gcfMarlinFirmware || gcf == gcfKlipper); - // bool silent_mode = m_config->opt_bool("silent_mode"); - // int max_field = silent_mode ? 2 : 1; - // //BBS: limits of BBL printer can't be edited. - // for (const std::string &opt : Preset::machine_limits_options()) - // for (int i = 0; i < max_field; ++ i) - // toggle_option(opt, !is_BBL_printer, i); - //} + if (m_active_page->title() == "Motion ability") { + auto gcf = m_config->option>("gcode_flavor")->value; + assert(gcf == gcfMarlinLegacy || gcf == gcfMarlinFirmware || gcf == gcfKlipper); + bool silent_mode = m_config->opt_bool("silent_mode"); + int max_field = silent_mode ? 2 : 1; + for (int i = 0; i < max_field; ++i) + toggle_option("machine_max_acceleration_travel", gcf == gcfMarlinFirmware, i); + toggle_line("machine_max_acceleration_travel", gcf == gcfMarlinFirmware); + } } void TabPrinter::update() @@ -3839,14 +3830,6 @@ void TabPrinter::update_fff() m_use_silent_mode = m_config->opt_bool("silent_mode"); } - auto gcf_ = - m_config->option>("gcode_flavor")->value; - bool supports_travel_acceleration = (gcf_ == gcfMarlinFirmware || gcf_ == gcfMarlinLegacy || gcf_ == gcfKlipper); - if (m_supports_travel_acceleration != supports_travel_acceleration) { - m_rebuild_kinematics_page = true; - m_supports_travel_acceleration = supports_travel_acceleration; - } - toggle_options(); } diff --git a/src/slic3r/GUI/Tab.hpp b/src/slic3r/GUI/Tab.hpp index d1d2ca0961..551eabd829 100644 --- a/src/slic3r/GUI/Tab.hpp +++ b/src/slic3r/GUI/Tab.hpp @@ -549,7 +549,6 @@ class TabPrinter : public Tab private: bool m_has_single_extruder_MM_page = false; bool m_use_silent_mode = false; - bool m_supports_travel_acceleration = false; void append_option_line(ConfigOptionsGroupShp optgroup, const std::string opt_key); bool m_rebuild_kinematics_page = false;