Merge branch 'master' into updating

xs/src/libslic3r/PrintConfig.cpp

@@ -166,6 +166,22 @@ PrintConfigDef::PrintConfigDef()
     def->cli = "cooling!";
     def->default_value = new ConfigOptionBools { true };
 
+    def = this->add("cooling_tube_retraction", coFloat);
+    def->label = L("Cooling tube position");
+    def->tooltip = L("Distance of the center-point of the cooling tube from the extruder tip ");
+    def->sidetext = L("mm");
+    def->cli = "cooling_tube_retraction=f";
+    def->min = 0;
+    def->default_value = new ConfigOptionFloat(91.5f);
+
+    def = this->add("cooling_tube_length", coFloat);
+    def->label = L("Cooling tube length");
+    def->tooltip = L("Length of the cooling tube to limit space for cooling moves inside it ");
+    def->sidetext = L("mm");
+    def->cli = "cooling_tube_length=f";
+    def->min = 0;
+    def->default_value = new ConfigOptionFloat(5.f);
+
     def = this->add("default_acceleration", coFloat);
     def->label = L("Default");
     def->tooltip = L("This is the acceleration your printer will be reset to after "
@@ -439,6 +455,49 @@ PrintConfigDef::PrintConfigDef()
     def->min = 0;
     def->default_value = new ConfigOptionFloats { 0. };
 
+    def = this->add("filament_loading_speed", coFloats);
+    def->label = L("Loading speed");
+    def->tooltip = L("Speed used for loading the filament on the wipe tower. ");
+    def->sidetext = L("mm/s");
+    def->cli = "filament-loading-speed=f@";
+    def->min = 0;
+    def->default_value = new ConfigOptionFloats { 28. };
+
+    def = this->add("filament_unloading_speed", coFloats);
+    def->label = L("Unloading speed");
+    def->tooltip = L("Speed used for unloading the filament on the wipe tower (does not affect "
+                      " initial part of unloading just after ramming). ");
+    def->sidetext = L("mm/s");
+    def->cli = "filament-unloading-speed=f@";
+    def->min = 0;
+    def->default_value = new ConfigOptionFloats { 90. };
+
+    def = this->add("filament_toolchange_delay", coFloats);
+    def->label = L("Delay after unloading");
+    def->tooltip = L("Time to wait after the filament is unloaded. "
+                   "May help to get reliable toolchanges with flexible materials "
+                   "that may need more time to shrink to original dimensions. ");
+    def->sidetext = L("s");
+    def->cli = "filament-toolchange-delay=f@";
+    def->min = 0;
+    def->default_value = new ConfigOptionFloats { 0. };
+    
+    def = this->add("filament_cooling_time", coFloats);
+    def->label = L("Cooling time");
+    def->tooltip = L("The filament is slowly moved back and forth after retraction into the cooling tube "
+                   "for this amount of time.");
+    def->cli = "filament_cooling_time=i@";
+    def->sidetext = L("s");
+    def->min = 0;
+    def->default_value = new ConfigOptionFloats { 14.f };
+
+    def = this->add("filament_ramming_parameters", coStrings);
+    def->label = L("Ramming parameters");
+    def->tooltip = L("This string is edited by RammingDialog and contains ramming specific parameters ");
+    def->cli = "filament-ramming-parameters=s@";
+    def->default_value = new ConfigOptionStrings { "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0|"
+	   " 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" };
+
     def = this->add("filament_diameter", coFloats);
     def->label = L("Diameter");
     def->tooltip = L("Enter your filament diameter here. Good precision is required, so use a caliper "
@@ -977,6 +1036,15 @@ PrintConfigDef::PrintConfigDef()
     def->cli = "overhangs!";
     def->default_value = new ConfigOptionBool(true);
 
+    def = this->add("parking_pos_retraction", coFloat);
+    def->label = L("Filament parking position");
+    def->tooltip = L("Distance of the extruder tip from the position where the filament is parked "
+                      "when unloaded. This should match the value in printer firmware. ");
+    def->sidetext = L("mm");
+    def->cli = "parking_pos_retraction=f";
+    def->min = 0;
+    def->default_value = new ConfigOptionFloat(92.f);
+
     def = this->add("perimeter_acceleration", coFloat);
     def->label = L("Perimeters");
     def->tooltip = L("This is the acceleration your printer will use for perimeters. "
@@ -1744,6 +1812,25 @@ PrintConfigDef::PrintConfigDef()
     def->cli = "wipe-tower!";
     def->default_value = new ConfigOptionBool(false);
 
+    def = this->add("wiping_volumes_extruders", coFloats);
+    def->label = L("Purging volumes - load/unload volumes");
+    def->tooltip = L("This vector saves required volumes to change from/to each tool used on the "
+                     "wipe tower. These values are used to simplify creation of the full purging "
+                     "volumes below. ");
+    def->cli = "wiping-volumes-extruders=f@";
+    def->default_value = new ConfigOptionFloats { 70.f, 70.f, 70.f, 70.f, 70.f, 70.f, 70.f, 70.f, 70.f, 70.f  };
+
+    def = this->add("wiping_volumes_matrix", coFloats);
+    def->label = L("Purging volumes - matrix");
+    def->tooltip = L("This matrix describes volumes (in cubic milimetres) required to purge the"
+                     " new filament on the wipe tower for any given pair of tools. ");
+    def->cli = "wiping-volumes-matrix=f@";
+    def->default_value = new ConfigOptionFloats {   0.f, 140.f, 140.f, 140.f, 140.f,
+                                                  140.f,   0.f, 140.f, 140.f, 140.f,
+                                                  140.f, 140.f,   0.f, 140.f, 140.f,
+                                                  140.f, 140.f, 140.f,   0.f, 140.f,
+                                                  140.f, 140.f, 140.f, 140.f,   0.f };
+
     def = this->add("wipe_tower_x", coFloat);
     def->label = L("Position X");
     def->tooltip = L("X coordinate of the left front corner of a wipe tower");
@@ -1765,14 +1852,19 @@ PrintConfigDef::PrintConfigDef()
     def->cli = "wipe-tower-width=f";
     def->default_value = new ConfigOptionFloat(60.);
 
-    def = this->add("wipe_tower_per_color_wipe", coFloat);
-    def->label = L("Per color change depth");
-    def->tooltip = L("Depth of a wipe color per color change. For N colors, there will be "
-                   "maximum (N-1) tool switches performed, therefore the total depth "
-                   "of the wipe tower will be (N-1) times this value.");
+    def = this->add("wipe_tower_rotation_angle", coFloat);
+    def->label = L("Wipe tower rotation angle");
+    def->tooltip = L("Wipe tower rotation angle with respect to x-axis ");
+    def->sidetext = L("degrees");
+    def->cli = "wipe-tower-rotation-angle=f";
+    def->default_value = new ConfigOptionFloat(0.);
+    
+    def = this->add("wipe_tower_bridging", coFloat);
+    def->label = L("Maximal bridging distance");
+    def->tooltip = L("Maximal distance between supports on sparse infill sections. ");
     def->sidetext = L("mm");
-    def->cli = "wipe-tower-per-color-wipe=f";
-    def->default_value = new ConfigOptionFloat(15.);
+    def->cli = "wipe-tower-bridging=f";
+    def->default_value = new ConfigOptionFloat(10.);
 
     def = this->add("xy_size_compensation", coFloat);
     def->label = L("XY Size Compensation");
@@ -1852,8 +1944,9 @@ void PrintConfigDef::handle_legacy(t_config_option_key &opt_key, std::string &va
         "standby_temperature", "scale", "rotate", "duplicate", "duplicate_grid",
         "start_perimeters_at_concave_points", "start_perimeters_at_non_overhang", "randomize_start", 
         "seal_position", "vibration_limit", "bed_size", "octoprint_host",
-        "print_center", "g0", "threads", "pressure_advance" 
+        "print_center", "g0", "threads", "pressure_advance", "wipe_tower_per_color_wipe"
     };
+
     if (ignore.find(opt_key) != ignore.end()) {
         opt_key = "";
         return;