3D-printing/Cura
1
0
Fork 0
mirror of https://github.com/Ultimaker/Cura.git synced 2026-01-31 21:30:46 -07:00
Code Issues Projects Releases Packages Wiki Activity Actions 2
22045 commits 353 branches 328 tags 833 MiB
Commit graph

1254 commits

Author SHA1 Message Date
Jaime van Kessel
b5bf3e8e85
Merge branch 'mb-bridge-skin-over-sparse-infill' of https://github.com/smartavionics/Cura 2019-11-26 15:41:04 +01:00
Remco Burema
25f0460231
Add missing 'material break preparation temperature'. 
part of CURA-6971
 2019-11-22 12:01:46 +01:00
Jaime van Kessel
c65ccf29b0
Merge branch 'mb-shared-heater' of https://github.com/smartavionics/Cura 2019-11-14 11:06:12 +01:00
Ghostkeeper
d25ca84c6c
Make small feature max length a child setting of small hole max size 
The small hole max size is not used in CuraEngine. It may not be a leaf setting then. Instead, Small Feature Max Length is used which is directly dependent on Small Hole Max Size. They are simply different units of the same thing. This is how we should structure these settings then.
 2019-11-03 02:20:18 +01:00
Ghostkeeper
0c846d76a1
Correct setting name and description of wipe Z hop 
This hop is executed regardless of whether or not the wipe is retracted.
 2019-11-03 01:41:51 +01:00
Ghostkeeper
e2b8a44e2d
Better defaults for retraction and z hop during wipe 
Let's use the normal retraction and z hop settings to be safe. Should work fine.
 2019-11-03 01:18:35 +01:00
Ghostkeeper
0b6938e9aa
Specify that this setting is about wiping 2019-11-03 01:14:38 +01:00
Ghostkeeper
eaedca1917
Convert unit of adaptive layers threshold and change name 
This usage is hopefully more intuitive than the previous one.
 2019-11-01 11:54:17 +01:00
Ghostkeeper
0ea67d18d2
Only show strategy-specific settings if their WP strategy is activated 
Reduces confusion, I hope, and the feeling of being overwhelmed by a load of settings, because obviously only people who make all settings visible are going to see these settings at all.
 2019-10-27 01:00:17 +02:00
Ghostkeeper
7dada6539c
Fix minimum speeds and distances for wire printing 
Minimum distance is 0.001, i.e. one micrometre. Minimum speeds are set to Marlin's Minimum Planner Speed which is hardcoded.
 2019-10-26 01:12:34 +02:00
Ghostkeeper
11d30dab56
Improve setting descriptions for flow rate compensation settings 
The original setting descriptions were wholly undescriptive...

Done during investigation of these settings for the Setting Guide.
 2019-10-25 23:21:30 +02:00
Ghostkeeper
cb9b385a85
Remove Alternate Skin Rotations setting 
It's been replaced completely by the Top/Bottom Line Directions setting.
 2019-10-22 13:46:42 +02:00
Lipu Fei
cd0dbb3902 Fix defaultExtruderPosition() usage in fdmprinter 
CURA-6913

getDefaultValueInExtruder() expects the extruder_position to be an int,
but defaultExtruderPosition() returns a str. This will cause the formula
evaluation to fail.
 2019-10-21 09:22:55 +02:00
Ghostkeeper
8cd583ad33
Only show conical support min width if angle is positive 
If the angle is 0 or negative, this setting won't have any effect since the support cannot be made wider than it already is using this setting. It can only prevent it from becoming smaller, and it will only become smaller from a positive conical support angle.

Discovered during work on the Settings Guide.
 2019-10-21 01:48:01 +02:00
Remco Burema
15bdf0fa1c Change the description of 'Initial Bottom Layers'. 
part of CURA-5918
 2019-10-18 14:00:16 +02:00
Remco Burema
1885dddf45 Merge branch 'feat_open_top_bottom' of https://github.com/BagelOrb/Cura into BagelOrb-feat_open_top_bottom 2019-10-18 12:55:52 +02:00
Ghostkeeper
84c9b28bb2
Move maximum resolution itself out of experimental as well 
This was forgotten accidentally, it seems.
 2019-10-18 00:07:43 +02:00
Ghostkeeper
ad5fae5b66
Only allow optimising infill travels when combing is enabled 
That's the only time when it will have any effect, since the only thing this does is to calculate the distance to the next infill line better if the nozzle has to make a detour due to combing.
 2019-10-17 01:29:24 +02:00
Ghostkeeper
cf14fa6820
Merge branch 'feature_intent' 
Here we go!

Contributes to issue CURA-6864.
 2019-10-08 13:17:54 +02:00
Remco Burema
6ed2b79166 Rename 'First Layer Speed' which is about small features. 2019-10-08 11:24:29 +02:00
Ghostkeeper
c7ba02bdfb
Only show support interface angles settings if support is enabled 2019-10-08 10:38:20 +02:00
Lipu Fei
32747d2abe Merge remote-tracking branch 'origin/master' into feature_intent 2019-10-07 21:20:54 +02:00
Ghostkeeper
d1f9245d26
Move Maximum Resolution and Maximum Deviation out of experimental 
Yes, it does comply to our Definition of Not Experimental. And I asked.
 2019-10-07 17:17:43 +02:00
Ghostkeeper
225d1a2ac1
Allow minimum circumference to be 0 
It should just not filter then.
 2019-10-07 15:25:49 +02:00
Lipu Fei
0d554c4938 Merge remote-tracking branch 'origin/master' into feature_intent 2019-10-04 10:19:36 +02:00
Ghostkeeper
672fc58930
Allow down to half the layer height for infill layer thickness 
This is possible because CuraEngine rounds these to the nearest layer thickness. So if it's more than half the layer height it gets rounded up and it's still properly one layer.

Contributes to issue #6465.
 2019-10-02 12:59:48 +02:00
Lipu Fei
750632ec41 Merge remote-tracking branch 'origin/master' into feature_intent 2019-10-02 12:52:37 +02:00
Jaime van Kessel
872d6365a9
Fix seam location if it's relative 2019-10-02 10:45:50 +02:00
Lipu Fei
96a9bcccbb Merge remote-tracking branch 'origin/master' into feature_intent 2019-10-01 09:41:05 +02:00
Lipu Fei
609ceed140
Merge pull request #6426 from Ultimaker/CURA-6106_fix_interface_disappearing 
Warn when difference between X/Y distance and minimum X/Y distance is too big
 2019-10-01 09:40:05 +02:00
Ghostkeeper
5c2c4118c6
Add clarification about that supported overhang doesn't fall into this category 
Fixes #6436.
 2019-09-30 12:58:36 +02:00
Ghostkeeper
3c17af6192
Clarify description of support interface area settings 
They'll be generated and then tossed away. I'm specifying that there will be normal support in its place, unlike the minimum support area setting that replaces the support with air. It won't be air here, but normal support.
 2019-09-29 18:25:11 +02:00
Ghostkeeper
53a535a077
Warn when difference between X/Y distance and minimum X/Y distance is too big 
This could cause a large overhang.

Contributes to issue CURA-6106.
 2019-09-26 17:05:05 +02:00
Ghostkeeper
0c873d1757
Fix inheritance of support interface line direction settings 
Fixes #6412.
 2019-09-25 11:42:34 +02:00
Ghostkeeper
9f1b434a7e
Don't show support brim width if support brim is disabled 2019-09-25 11:15:21 +02:00
Lipu Fei
94e89ad4ac Fix merge conflicts with master 2019-09-24 14:26:43 +02:00
Lipu Fei
bd314a765f Update setting_version 
CURA-6799
 2019-09-24 11:19:03 +02:00
Jaime van Kessel
7016e791c8
Fix containertree for machines without materials but with specific qualities 
CURA-6775
 2019-09-19 15:33:19 +02:00
Mark Burton
fb5ec97cb8 Fix spelling. 2019-09-14 20:19:52 +01:00
Lipu Fei
fa8213c601 Merge remote-tracking branch 'origin/feature_intent_container_tree' into feature_intent_upgrade 2019-09-13 10:31:11 +02:00
Diego Prado Gesto
bca68c6db0 Merge branch 'feature_intent' into feature_intent_container_tree 2019-09-13 09:02:51 +02:00
Jaime van Kessel
5e4f673ec2
Merge branch '4.3' of github.com:Ultimaker/Cura 2019-09-11 16:10:12 +02:00
Jaime van Kessel
ab910c2a37
Disable retraction min travel 
It's broken right now, so we should enable it again once it's fixed

CURA-6675
 2019-09-11 15:12:49 +02:00
Jaime van Kessel
d6d06fb85b
Merge branch 'feature_intent_container_tree' of github.com:Ultimaker/Cura into feature_intent_upgrade 2019-09-10 15:07:57 +02:00
Diego Prado Gesto
b18565d9cf Merge branch 'master' into feature_intent_container_tree 2019-09-10 11:08:21 +02:00
Jaime van Kessel
e9862fb348
Move version upgrade for intents from 4.1-4.2 to 4.3-4.4 
CURA-6599
 2019-09-10 10:57:25 +02:00
Ghostkeeper
354729b621
Only show support flow if support is enabled 2019-09-07 23:19:59 +02:00
Ghostkeeper
5e302c6a67
Fix display of Z Hop After Extruder Switch Height on single extruder 
If the setting is enabled on a single extruder printer, it'll show the Z Hop Height setting anyway even though it has no effect.
 2019-09-07 23:18:02 +02:00
Jaime van Kessel
d1a8ce54a1 Merge branch 'feature_intent' of github.com:Ultimaker/Cura into feature_intent_container_tree 2019-08-27 14:18:41 +02:00
Ghostkeeper
0302ae4257
Don't find any variants if the machine says it doesn't have them 
Even if there might be a matching variant...

Contributes to issue CURA-6600.
 2019-08-22 15:44:41 +02:00