Remove experimental tag from ASA and SR30.

Map mk14_e to LABS extruder.

PP-502

cura/PrinterOutput/Models/ExtruderConfigurationModel.py

@@ -50,7 +50,8 @@ class ExtruderConfigurationModel(QObject):
             "mk14_hot_s":"2XA",
             "mk14_c":"1C",
             "mk14":"1A",
-            "mk14_s":"2A"
+            "mk14_s":"2A",
+            "mk14_e": "LABS"
         }
         if hotendId in _EXTRUDER_NAME_MAP:
             return _EXTRUDER_NAME_MAP[hotendId]

resources/definitions/ultimaker_method_base.def.json

@@ -354,7 +354,6 @@
         "raft_smoothing": { "value": 9.5 },
         "raft_surface_extruder_nr": { "value": "int(anyExtruderWithMaterial('material_is_support_material')) if support_enable and extruderValue(support_extruder_nr,'material_is_support_material') else raft_base_extruder_nr" },
         "raft_surface_fan_speed": { "value": 0 },
-        "raft_surface_wall_count": { "value": "raft_wall_count" },
         "raft_wall_count": { "value": 2 },
         "retract_at_layer_change": { "value": true },
         "retraction_amount": { "value": 0.75 },
@@ -365,7 +364,7 @@
         "retraction_hop": { "value": 0.4 },
         "retraction_hop_enabled": { "value": true },
         "retraction_hop_only_when_collides": { "value": false },
-        "retraction_min_travel": { "value": "0.6 if extruder_nr == support_extruder_nr else 5" },
+        "retraction_min_travel": { "value": "0.6 if material_is_support_material else 5" },
         "retraction_prime_speed": { "value": "retraction_speed" },
         "retraction_speed": { "value": 5 },
         "roofing_layer_count": { "value": 2 },
@@ -392,35 +391,34 @@
         "speed_wall_0": { "value": "speed_wall * 30/40" },
         "speed_wall_x": { "value": "speed_wall" },
         "support_angle": { "value": 40 },
-        "support_bottom_distance": { "value": "layer_height if extruder_nr == support_extruder_nr else support_z_distance" },
+        "support_bottom_distance": { "value": "layer_height if material_is_support_material else support_z_distance" },
-        "support_bottom_enable": { "value": "False if extruder_nr == support_extruder_nr else True" },
+        "support_bottom_enable": { "value": "not(material_is_support_material)" },
         "support_bottom_height": { "value": "2*support_infill_sparse_thickness" },
         "support_bottom_material_flow": { "value": "material_flow" },
-        "support_bottom_wall_count": { "value": "0 if extruder_nr == support_extruder_nr else support_wall_count" },
+        "support_bottom_wall_count": { "value": "0 if material_is_support_material else support_wall_count" },
         "support_brim_enable": { "value": false },
         "support_conical_min_width": { "value": 10 },
         "support_enable": { "value": true },
         "support_extruder_nr": { "value": "int(anyExtruderWithMaterial('material_is_support_material'))" },
-        "support_fan_enable": { "value": "true if extruder_nr == support_extruder_nr else false" },
+        "support_fan_enable": { "value": "material_is_support_material" },
         "support_infill_rate": { "value": 20.0 },
         "support_infill_sparse_thickness": { "value": "layer_height" },
         "support_interface_enable": { "value": true },
         "support_interface_height": { "value": "4*support_infill_sparse_thickness" },
         "support_interface_material_flow": { "value": "material_flow" },
-        "support_interface_offset": { "value": "1 if extruder_nr == support_extruder_nr else 0.8" },
+        "support_interface_offset": { "value": "1 if material_is_support_material else 0.8" },
         "support_interface_pattern": { "value": "'lines'" },
-        "support_interface_wall_count": { "value": "1 if extruder_nr == support_extruder_nr else 2" },
+        "support_interface_wall_count": { "value": "1 if material_is_support_material else 2" },
         "support_material_flow": { "value": "material_flow" },
-        "support_offset": { "value": "1.8 if extruder_nr == support_extruder_nr else 0.8" },
+        "support_offset": { "value": "1.8 if material_is_support_material else 0.8" },
         "support_pattern": { "value": "'lines'" },
-        "support_roof_height": { "value": "4*layer_height if extruder_nr == support_extruder_nr else 5*layer_height" },
+        "support_roof_height": { "value": "4*layer_height if material_is_support_material else 5*layer_height" },
         "support_roof_material_flow": { "value": "material_flow" },
         "support_supported_skin_fan_speed": { "value": "cool_fan_speed_max" },
-        "support_top_distance": { "value": 0.25 },
+        "support_top_distance": { "value": "0.25 if material_is_support_material else support_z_distance" },
         "support_wall_count": { "value": "2 if support_conical_enabled or support_structure == 'tree' else 0" },
-        "support_xy_distance": { "value": "0.3 if extruder_nr == support_infill_extruder_nr else 0.2" },
+        "support_xy_distance": { "value": "0.3 if material_is_support_material else 0.2" },
-        "support_xy_distance_overhang": { "value": "0.3 if extruder_nr == support_infill_extruder_nr else 0.2" },
+        "support_xy_distance_overhang": { "value": "support_xy_distance" },
-        "support_z_distance": { "value": 0 },
         "switch_extruder_retraction_amount": { "value": 0.5 },
         "switch_extruder_retraction_speeds": { "value": "retraction_speed" },
         "top_bottom_thickness": { "value": "5*layer_height" },

resources/intent/ultimaker_methodx/um_methodx_1c_um-asa-175_0.2mm_solid.inst.cfg

@@ -5,7 +5,6 @@ version = 4
 
 [metadata]
 intent_category = solid
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/intent/ultimaker_methodx/um_methodx_1xa_um-asa-175_0.2mm_solid.inst.cfg

@@ -5,7 +5,6 @@ version = 4
 
 [metadata]
 intent_category = solid
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/intent/ultimaker_methodx/um_methodx_labs_um-asa-175_0.2mm_solid.inst.cfg

@@ -5,7 +5,6 @@ version = 4
 
 [metadata]
 intent_category = solid
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/intent/ultimaker_methodxl/um_methodxl_1c_um-asa-175_0.2mm_solid.inst.cfg

@@ -5,7 +5,6 @@ version = 4
 
 [metadata]
 intent_category = solid
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/intent/ultimaker_methodxl/um_methodxl_1xa_um-asa-175_0.2mm_solid.inst.cfg

@@ -5,7 +5,6 @@ version = 4
 
 [metadata]
 intent_category = solid
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/intent/ultimaker_methodxl/um_methodxl_labs_um-asa-175_0.2mm_solid.inst.cfg

@@ -5,7 +5,6 @@ version = 4
 
 [metadata]
 intent_category = solid
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_method/um_method_1a_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_layers = 1
@@ -58,7 +60,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_method/um_method_1c_um-nylon12-cf-175_0.2mm.inst.cfg

@@ -16,10 +16,10 @@ cool_fan_enabled = False
 material_final_print_temperature = =default_material_print_temperature-5
 material_initial_print_temperature = =default_material_print_temperature-5
 raft_airgap = 0.3
-raft_base_line_spacing = =3 if extruder_nr == raft_interface_extruder_nr else 2
+raft_base_line_spacing = =3 if extruder_nr == support_extruder_nr else 2
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1
 raft_base_speed = 10
-raft_base_thickness = =0.6 if extruder_nr == raft_interface_extruder_nr else 0.5
+raft_base_thickness = =0.6 if extruder_nr == support_extruder_nr else 0.4
 retraction_amount = 0.5
 retraction_min_travel = 3.2
 small_skin_width = 3.6

resources/quality/ultimaker_method/um_method_1c_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_layers = 1
@@ -58,7 +60,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_method/um_method_labs_um-nylon12-cf-175_0.2mm.inst.cfg

@@ -16,10 +16,10 @@ cool_fan_enabled = False
 material_final_print_temperature = =default_material_print_temperature-5
 material_initial_print_temperature = =default_material_print_temperature-5
 raft_airgap = 0.3
-raft_base_line_spacing = =3 if extruder_nr == raft_interface_extruder_nr else 2
+raft_base_line_spacing = =3 if extruder_nr == support_extruder_nr else 2
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1
 raft_base_speed = 10
-raft_base_thickness = =0.6 if extruder_nr == raft_interface_extruder_nr else 0.5
+raft_base_thickness = =0.6 if extruder_nr == support_extruder_nr else 0.4
 retraction_amount = 0.5
 retraction_min_travel = 3.2
 small_skin_width = 3.6

resources/quality/ultimaker_method/um_method_labs_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_layers = 1
@@ -58,7 +60,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_methodx/um_methodx_1a_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_layers = 1
@@ -58,7 +60,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_methodx/um_methodx_1c_um-abscf-175_0.2mm.inst.cfg

@@ -48,7 +48,6 @@ support_interface_offset = 1.2
 support_line_width = 0.35
 support_material_flow = 90
 support_roof_density = 82
-support_roof_line_width = 0.4
 support_use_towers = True
 support_xy_distance = 0.3
 support_xy_distance_overhang = 0.25

resources/quality/ultimaker_methodx/um_methodx_1c_um-asa-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodx
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodx/um_methodx_1c_um-nylon12-cf-175_0.2mm.inst.cfg

@@ -16,10 +16,10 @@ cool_fan_enabled = False
 material_final_print_temperature = =default_material_print_temperature-5
 material_initial_print_temperature = =default_material_print_temperature-5
 raft_airgap = 0.3
-raft_base_line_spacing = =3 if extruder_nr == raft_interface_extruder_nr else 2
+raft_base_line_spacing = =3 if extruder_nr == support_extruder_nr else 2
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1
 raft_base_speed = 10
-raft_base_thickness = =0.6 if extruder_nr == raft_interface_extruder_nr else 0.5
+raft_base_thickness = =0.6 if extruder_nr == support_extruder_nr else 0.4
 retraction_amount = 0.5
 retraction_min_travel = 3.2
 small_skin_width = 3.6

resources/quality/ultimaker_methodx/um_methodx_1c_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_layers = 1
@@ -58,7 +60,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_methodx/um_methodx_1xa_um-asa-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodx
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodx/um_methodx_2xa_um-sr30-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodx
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_sr30_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodx/um_methodx_labs_um-abscf-175_0.2mm.inst.cfg

@@ -48,7 +48,6 @@ support_interface_offset = 1.2
 support_line_width = 0.35
 support_material_flow = 90
 support_roof_density = 82
-support_roof_line_width = 0.4
 support_use_towers = True
 support_xy_distance = 0.3
 support_xy_distance_overhang = 0.25

resources/quality/ultimaker_methodx/um_methodx_labs_um-asa-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodx
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodx/um_methodx_labs_um-nylon12-cf-175_0.2mm.inst.cfg

@@ -16,10 +16,10 @@ cool_fan_enabled = False
 material_final_print_temperature = =default_material_print_temperature-5
 material_initial_print_temperature = =default_material_print_temperature-5
 raft_airgap = 0.3
-raft_base_line_spacing = =3 if extruder_nr == raft_interface_extruder_nr else 2
+raft_base_line_spacing = =3 if extruder_nr == support_extruder_nr else 2
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1
 raft_base_speed = 10
-raft_base_thickness = =0.6 if extruder_nr == raft_interface_extruder_nr else 0.5
+raft_base_thickness = =0.6 if extruder_nr == support_extruder_nr else 0.4
 retraction_amount = 0.5
 retraction_min_travel = 3.2
 small_skin_width = 3.6

resources/quality/ultimaker_methodx/um_methodx_labs_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_layers = 1
@@ -58,7 +60,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_methodxl/um_methodxl_1a_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_line_spacing = 0.75
@@ -56,7 +58,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_methodxl/um_methodxl_1c_um-abscf-175_0.2mm.inst.cfg

@@ -50,7 +50,6 @@ support_interface_offset = 1.2
 support_line_width = 0.35
 support_material_flow = 90
 support_roof_density = 82
-support_roof_line_width = 0.4
 support_use_towers = True
 support_xy_distance = 0.3
 support_xy_distance_overhang = 0.25

resources/quality/ultimaker_methodxl/um_methodxl_1c_um-asa-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodxl
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodxl/um_methodxl_1c_um-nylon12-cf-175_0.2mm.inst.cfg

@@ -16,10 +16,10 @@ cool_fan_enabled = False
 material_final_print_temperature = =default_material_print_temperature-5
 material_initial_print_temperature = =default_material_print_temperature-5
 raft_airgap = 0.3
-raft_base_line_spacing = =3 if extruder_nr == raft_interface_extruder_nr else 2
+raft_base_line_spacing = =3 if extruder_nr == support_extruder_nr else 2
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1
 raft_base_speed = 10
-raft_base_thickness = =0.6 if extruder_nr == raft_interface_extruder_nr else 0.5
+raft_base_thickness = =0.6 if extruder_nr == support_extruder_nr else 0.4
 retraction_amount = 0.5
 retraction_min_travel = 3.2
 small_skin_width = 3.6

resources/quality/ultimaker_methodxl/um_methodxl_1c_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_line_spacing = 0.75
@@ -56,7 +58,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z

resources/quality/ultimaker_methodxl/um_methodxl_1xa_um-asa-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodxl
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodxl/um_methodxl_2xa_um-sr30-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodxl
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_sr30_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodxl/um_methodxl_labs_um-abscf-175_0.2mm.inst.cfg

@@ -50,7 +50,6 @@ support_interface_offset = 1.2
 support_line_width = 0.35
 support_material_flow = 90
 support_roof_density = 82
-support_roof_line_width = 0.4
 support_use_towers = True
 support_xy_distance = 0.3
 support_xy_distance_overhang = 0.25

resources/quality/ultimaker_methodxl/um_methodxl_labs_um-asa-175_0.2mm.inst.cfg

@@ -1,10 +1,9 @@
 [general]
 definition = ultimaker_methodxl
-name = Fast - Experimental
+name = Fast
 version = 4
 
 [metadata]
-is_experimental = True
 material = ultimaker_asa_175
 quality_type = draft
 setting_version = 23

resources/quality/ultimaker_methodxl/um_methodxl_labs_um-nylon12-cf-175_0.2mm.inst.cfg

@@ -16,10 +16,10 @@ cool_fan_enabled = False
 material_final_print_temperature = =default_material_print_temperature-5
 material_initial_print_temperature = =default_material_print_temperature-5
 raft_airgap = 0.3
-raft_base_line_spacing = =3 if extruder_nr == raft_interface_extruder_nr else 2
+raft_base_line_spacing = =3 if extruder_nr == support_extruder_nr else 2
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1
 raft_base_speed = 10
-raft_base_thickness = =0.6 if extruder_nr == raft_interface_extruder_nr else 0.5
+raft_base_thickness = =0.6 if extruder_nr == support_extruder_nr else 0.4
 retraction_amount = 0.5
 retraction_min_travel = 3.2
 small_skin_width = 3.6

resources/quality/ultimaker_methodxl/um_methodxl_labs_um-pla-175_0.2mm.inst.cfg

@@ -21,12 +21,14 @@ cool_min_layer_time = 10
 cool_min_speed = 5
 cool_min_temperature = 205
 infill_sparse_density = 15
-material_print_temperature_layer_0 = 225
+material_final_print_temperature = =default_material_print_temperature - 5
+material_initial_print_temperature = =default_material_print_temperature - 5
+material_print_temperature_layer_0 = =default_material_print_temperature +15
 min_bead_width = =line_width * 0.75
 min_wall_line_width = =line_width * 0.75
 raft_airgap = 0.18
-raft_base_line_spacing = =4 if extruder_nr == raft_interface_extruder_nr else 2.8
+raft_base_line_spacing = =4 if extruder_nr == support_extruder_nr else 2.8
-raft_base_line_width = =1.2 if extruder_nr == raft_interface_extruder_nr else 1.4
+raft_base_line_width = =1.2 if extruder_nr == support_extruder_nr else 1.4
 raft_base_thickness = 0.6
 raft_interface_infill_overlap = 25
 raft_interface_line_spacing = 0.75
@@ -56,7 +58,6 @@ support_line_width = =line_width * 0.75
 support_material_flow = =material_flow * 0.8
 support_offset = 3
 support_roof_density = =support_interface_density
-support_roof_line_width = =line_width
 support_top_distance = =support_z_distance
 support_xy_distance = 0.3
 support_xy_overrides_z = xy_overrides_z