diff --git a/resources/definitions/Zyyx plus start gcode.txt b/resources/definitions/Zyyx plus start gcode.txt
new file mode 100644
index 0000000000..2e45c726ec
--- /dev/null
+++ b/resources/definitions/Zyyx plus start gcode.txt	
@@ -0,0 +1 @@
+; ZYYX+ start gcode\n; Author Theodor Hansson 2024\nM73 P0; enable build progress\nM104 S{material_print_temperature_layer_0} T0; set nozzle temperature\nM126 S0; Turn off fan\nG21; set units to mm\nG90; set positioning to absolute\nG130 X80 Y80 Z127 A127 B127 ; Set Stepper Vref to default value\n\n; Home xy-axis\nG162 X Y F2500; home XY axes maximum\nG92 X0 Y0\nG1 X-5 Y-5 F2500\nG162 X Y F200; home XY axes maximum slowly\nG92 X132.5 Y120\n\n; Home z-axis\nG161 Z F1100; home Z axis minimum\nG92 Z0\nG1 Z2 F1100\nG161 Z F100; home Z axis minimum slowly\nG92 Z0\nM132 Z; Recall home offsets for Z\n\n; Calibrate point 1 (we're already at point 1)\nM131 A; store surface calibration point 1\nG1 Z2 F1100; back up from buildplate\n\n; Calibrate point 2\nG1 X-44.5 Y120 F9000; move to 2nd probing point\nG161 Z F100\nM131 B; store surface calibration point 1\nG1 Z2 F1100; back up from buildplate\n\n; Calibrate point 3\nG1 X132.5 Y-110 F9000; move to 2nd probing point\nG161 Z F100\nM131 AB; store surface calibration point 3\nG1 Z2 F1100; back up from buildplate\nM132 AB; Activate auto-leveling\nG1 Z1 F1000\n\n; Lay prime strip\nM133 T0 P300; stabilize extruder temperature (abort after 5 mins)\nM126 S{cool_fan_speed_0}; Activate fan\nG4 P1000; Wait a little bit longer\nG1 X100 Y-110 Z0.2 F1000\nG1 X40 E9 F1000\nG1 X0 E12.5 F1000\nG92 E0 ; Set E to 0\n\n; End of start gcode
\ No newline at end of file
diff --git a/resources/definitions/Zyyx pro start gcode legacy.txt b/resources/definitions/Zyyx pro start gcode legacy.txt
new file mode 100644
index 0000000000..01ef5dc277
--- /dev/null
+++ b/resources/definitions/Zyyx pro start gcode legacy.txt	
@@ -0,0 +1,60 @@
+;start of ZYYX Pro startcode
+M73 P0; enable build progress
+G21; set units to mm
+G90; set positioning to absolute
+G130 X80 Y80 A127 B127 ; Set Stepper Vref to default value
+G162 X Y F3000; home XY axes maximum
+G161 Z F450
+G161 Z F450; home Z axis minimum
+G92 X0 Y0 Z0 E0
+G1 X0 Y0 Z20 F3000
+G1 X-120 Y-110 Z10 F3000
+G130 X0 Y0 Z3 A0 B0 ; Set Stepper Vref to low value
+M420 P10; set back fan speed 10 off 11-20 10-100%
+M140 S10 T0; set 100% heater power
+M140 S99 T0; set chamber heater negative hysteresis 19 degrees
+M140 S102 T0; set chamber heater positive hysteresis 2 degrees
+M140 S{material_bed_temperature_layer_0} T0; set chamber temperature
+M104 S100 T0; set extruder temp 100 while heating
+M134 T0; wait for heated chamber temperature
+M420 P13; set fan speed 10 off 11-20 10-100%
+G130 X80 Y80 Z64 A127 B127 ; Set Stepper Vref to default value
+; Perform probing of build plate
+G162 X Y F3000; home XY axes maximum
+G161 Z F450
+G161 Z F450; home Z axis minimum
+G92 X0 Y0 Z0 E0
+G1 X0 Y0 Z5 F200
+G161 Z F200; home Z axis minimum again
+G92 X0 Y0 Z0 E0
+M131 A; store surface calibration point 1
+G1 X0 Y0 Z5 F200
+G1 X-182 Y0 Z5 F3000; move to 2nd probing point
+G161 Z F200
+M131 B; store surface calibration point 2
+G92 X-182 Y0 Z0 E0
+G1 X-182 Y0 Z5 F200
+G1 X0 Y0 Z5 F3000; move to home point
+G161 Z F200; home Z axis minimum again
+G92 X0 Y0 Z0 E0; set reference again
+G1 X0 Y0 Z5 F200; clear Z
+G1 X0 Y-228 Z5 F3000; move to 3rd calibration point
+G161 Z F200
+M131 AB; store surface calibration point 3
+M132 AB; activate auto leveling
+G92 X0 Y-228 Z0 E0
+G1 X0 Y-228 Z5 F200
+G162 X Y F3000
+G161 Z F200
+G92 X135 Y115 Z0 E0
+M132 Z; Recall stored home offset for Z axis
+G1 X135 Y115 Z5 F450; clear nozzle from hole
+G1 X0 Y115 Z5 F3000; clear nozzle from hole
+; end of ZYYX pro build plate calibration
+M127; turn off fan
+M104 S{material_print_temperature_layer_0} T0
+M133 T0 ; stabilize extruder temperature
+;SET_ZXPARAM
+;SET_SUPPORT_BUMPMAP
+G92 E0 ; Set E to 0
+; end of ZYYX Pro start code
\ No newline at end of file
diff --git a/resources/definitions/Zyyx pro start gcode.txt b/resources/definitions/Zyyx pro start gcode.txt
new file mode 100644
index 0000000000..0876750b93
--- /dev/null
+++ b/resources/definitions/Zyyx pro start gcode.txt	
@@ -0,0 +1,52 @@
+;start of ZYYX Pro startcode
+M73 P0; enable build progress
+M420 P10; set back fan speed 10 off 11-20 10-100%
+M140 S10 T0; set 100% heater power
+M140 S99 T0; set chamber heater negative hysteresis 19 degrees
+M140 S102 T0; set chamber heater positive hysteresis 2 degrees
+M140 S60 T0; set chamber temperature
+M104 S{material_print_temperature_layer_0} T0; set nozzle temperature
+G21; set units to mm
+G90; set positioning to absolute
+G130 X80 Y90 A127 B127 ; Set Stepper Vref to default value
+; Start build plate homing
+G162 X Y F3000; home XY axes maximum
+G161 Z F1200; home Z axis minimum
+G92 X0 Y0 Z0 E0
+G1 X0 Y0 Z2 F2000
+G1 X-5 Y-5 Z2 F5000
+G162 X Y F300; home XY axes maximum
+G161 Z F200; home Z axis minimum
+G92 X0 Y0 Z0
+M131 A; store surface calibration point 1
+; Homing point 1 complete
+G1 X0 Y0 Z5 F3000; 
+G1 X-182 Y0 Z5 F10000; move to 2nd probing point
+G161 Z F200
+M131 B; store surface calibration point 2
+G92 X-182 Y0 Z0 E0
+G1 X-182 Y0 Z5 F10000
+; Homing point 2 complete
+G1 X0 Y-228 Z5 F8000; move to 3rd calibration point
+G161 Z F200
+M131 AB; store surface calibration point 3
+M132 AB; activate auto leveling
+; Homing point 2 complete
+G1 Z5 F3000
+G1 X-5 Y-5 F5000
+G162 X Y F300
+G1 Z5 F3000
+G161 Z F200
+G92 X135 Y115 Z0 E0
+M132 Z; Recall stored home offset for Z axis
+G1 Z10 F3000; clear nozzle from hole
+G1 X0 Y0 Z10 F8000; move to middle of plate
+; end of ZYYX pro build plate calibration
+M133 T0 ; stabilize extruder temperature
+M126; turn on fan to help heat chamber
+M134 T0; wait for heated chamber temperature
+M127; turn off fan when hot
+;SET_ZXPARAM
+;SET_SUPPORT_BUMPMAP
+G92 E0 ; Set E to 0
+; end of ZYYX Pro start code
\ No newline at end of file
diff --git a/resources/definitions/zyyx_testing.txt b/resources/definitions/zyyx_testing.txt
new file mode 100644
index 0000000000..52be7545fa
--- /dev/null
+++ b/resources/definitions/zyyx_testing.txt
@@ -0,0 +1,51 @@
+;RIGHT EXTRUDER
+; Replicator 1 dual start.gcode
+M73 P0 ; Enable build progress
+G21; set units to mm
+G90 ; absolute positioning
+G162 Z F3000 ; Home Z maximum
+G28 X Y ; Home X Y maximum
+G92 X0 Y0
+M140 S[bed0_temperature] T0 ; Heat buildplate
+M134 T0 ; Stabilize bed temperature
+M104 S180 T0 ; Heat right extruder
+M104 S70 T1 ; Heat lightly left extruder
+M133 T0 ; Stabilize right extruder temperature
+M133 T1 ; Stabilize left extruder temperature
+M104 S0 T1 ; cool down left extruder
+G0 X-45 Y-15; estrema destra in fondo punto di calibrazione ZERO prende offset primario di asse Z
+G161 Z F800
+G92 Z-5 ; Set Z to 5
+G4 P20000 ; 20 seconds wait, before beginning, to stabilize ambient temps
+G1 Z0
+G161 Z F50 ; Home Z maximum slowly
+M132 Z ; Recall home offsets for Z
+G1 Z10
+G28 X Y ; Home X Y maximum
+M132 X Y A B ; Recall home offsets for everything but Z
+G1 X-80 Y65 Z10 F2000 ; Prima posizione di calibrazione
+G161 Z F100
+M131 A ; prima posizione memorizzata
+G1 X100 Y-10 Z10 F2000 ; Seconda posizione di calibrazione
+G161 Z F100
+M131 B ; seconda posizione memorizzata
+G1 X-70 Y-10 Z10 F2000 ; Terza posizione di calibrazione
+G161 Z F100
+M131 AB ; Terza posizione memorizzata
+M132 AB ; avvio del livellamento automatico
+M135 T0 ; Load right extruder offsets
+G1 X-120 Y-75 Z30 F9000 ; Move to wait position off table
+G130 X20 Y20 Z20 A20 B20 ; Lower stepper Vrefs while heating
+M126 S[fan_speed_pwm] ; Set fan speed
+M104 S[extruder0_temperature] T0 ; Heat right extruder
+M133 T0 ; Stabilize right extruder temperature
+G130 X127 Y127 Z40 A127 B127 ; Default stepper Vrefs
+G92 A0 B0 ; Zero extruders
+G1 X100 Y-75 F9000 ; Move to front right corner of bed
+G1 Z0.4 F6000 ; Move down to purge
+G1 X-90 Y-75 E24 F2000 ; Extrude a line of filament across the front edge of the bed
+G1 X-100 Y-75 F180 ; Wait for ooze
+G1 X-110 Y-75 F5000 ; Fast wipe
+G1 Z0.2 F100 ; Lift
+M73 P1 ;@body (notify GPX body has started)
+; end of start.gcode
\ No newline at end of file
diff --git a/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fast.inst.cfg b/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fast.inst.cfg
index 6b068f93f1..d77ba343f4 100644
--- a/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fast.inst.cfg
+++ b/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fast.inst.cfg
@@ -14,7 +14,6 @@ weight = 0
 adhesion_type = brim
 default_material_print_temperature = 240
 infill_sparse_density = 10
-material_flow = 95
 material_print_temperature_layer_0 = 250
 raft_airgap = 0.15
 retraction_amount = 1.2
diff --git a/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fine.inst.cfg b/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fine.inst.cfg
index 8b8b6cb50c..d787b89af6 100644
--- a/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fine.inst.cfg
+++ b/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_fine.inst.cfg
@@ -14,7 +14,6 @@ weight = 0
 adhesion_type = brim
 default_material_print_temperature = 240
 infill_sparse_density = 15
-material_flow = 95
 material_print_temperature_layer_0 = 250
 raft_airgap = 0.15
 retraction_amount = 1.2
diff --git a/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_normal.inst.cfg b/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_normal.inst.cfg
index 8cfa971135..0222acec12 100644
--- a/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_normal.inst.cfg
+++ b/resources/quality/zyyx_plus/ABS/zyyx_plus_abs_normal.inst.cfg
@@ -14,7 +14,6 @@ weight = 0
 adhesion_type = brim
 default_material_print_temperature = 240
 infill_sparse_density = 15
-material_flow = 95
 material_print_temperature_layer_0 = 250
 raft_airgap = 0.15
 retraction_amount = 1.2
diff --git a/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fast.inst.cfg b/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fast.inst.cfg
index 0391586281..e5bcfcf6a2 100644
--- a/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fast.inst.cfg
+++ b/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fast.inst.cfg
@@ -14,7 +14,6 @@ weight = 0
 adhesion_type = brim
 default_material_print_temperature = 210
 infill_sparse_density = 10
-material_flow = 95
 material_print_temperature_layer_0 = 225
 raft_airgap = 0.15
 retraction_amount = 1.2
diff --git a/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fine.inst.cfg b/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fine.inst.cfg
index 247243d08c..25f965eee4 100644
--- a/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fine.inst.cfg
+++ b/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_fine.inst.cfg
@@ -14,7 +14,6 @@ weight = 0
 adhesion_type = brim
 default_material_print_temperature = 210
 infill_sparse_density = 15
-material_flow = 95
 material_print_temperature_layer_0 = 225
 raft_airgap = 0.15
 retraction_amount = 1.2
diff --git a/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_normal.inst.cfg b/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_normal.inst.cfg
index fde2542074..27e4166972 100644
--- a/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_normal.inst.cfg
+++ b/resources/quality/zyyx_plus/PLA/zyyx_plus_pla_normal.inst.cfg
@@ -14,7 +14,6 @@ weight = 0
 adhesion_type = brim
 default_material_print_temperature = 210
 infill_sparse_density = 15
-material_flow = 95
 material_print_temperature_layer_0 = 225
 raft_airgap = 0.15
 retraction_amount = 1.2
diff --git a/resources/quality/zyyx_plus/zyyx_plus_global_draft.inst.cfg b/resources/quality/zyyx_plus/zyyx_plus_global_draft.inst.cfg
new file mode 100644
index 0000000000..1cc4d4df13
--- /dev/null
+++ b/resources/quality/zyyx_plus/zyyx_plus_global_draft.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 4
+name = Draft
+definition = zyyx_plus
+
+[metadata]
+setting_version = 1
+type = quality
+quality_type = fast
+weight = 0
+global_quality = True
+
+[values]
+layer_height = 0.3
+adhesion_type = brim
+infill_sparse_density = 10
+raft_airgap = 0.15
+retraction_amount = 1.2
+retraction_speed = 20
+speed_print = 55
+speed_wall = =math.ceil(speed_print * 22 / 50)
+speed_wall_x = =math.ceil(speed_print * 33 / 50)
+top_bottom_thickness = 0.9
+wall_thickness = 0.8
diff --git a/resources/quality/zyyx_plus/zyyx_plus_global_fast.inst.cfg b/resources/quality/zyyx_plus/zyyx_plus_global_fast.inst.cfg
index d9b586b5b9..fa9c5c00fa 100644
--- a/resources/quality/zyyx_plus/zyyx_plus_global_fast.inst.cfg
+++ b/resources/quality/zyyx_plus/zyyx_plus_global_fast.inst.cfg
@@ -12,3 +12,13 @@ global_quality = True
 
 [values]
 layer_height = 0.2
+adhesion_type = brim
+infill_sparse_density = 10
+raft_airgap = 0.15
+retraction_amount = 1.2
+retraction_speed = 20
+speed_print = 55
+speed_wall = =math.ceil(speed_print * 22 / 50)
+speed_wall_x = =math.ceil(speed_print * 33 / 50)
+top_bottom_thickness = 0.8
+wall_thickness = 0.8
\ No newline at end of file
diff --git a/resources/quality/zyyx_plus/zyyx_plus_global_fine.inst.cfg b/resources/quality/zyyx_plus/zyyx_plus_global_fine.inst.cfg
index c994ded909..c4fefa9b52 100644
--- a/resources/quality/zyyx_plus/zyyx_plus_global_fine.inst.cfg
+++ b/resources/quality/zyyx_plus/zyyx_plus_global_fine.inst.cfg
@@ -12,4 +12,14 @@ global_quality = True
 
 [values]
 layer_height = 0.1
-infill_pattern = gyroid
\ No newline at end of file
+infill_pattern = gyroid
+adhesion_type = brim
+infill_sparse_density = 15
+raft_airgap = 0.15
+retraction_amount = 1.2
+retraction_speed = 20
+speed_print = 40
+speed_wall = =math.ceil(speed_print * 22 / 50)
+speed_wall_x = =math.ceil(speed_print * 33 / 50)
+top_bottom_thickness = 1.0
+wall_thickness = 1.2
\ No newline at end of file
diff --git a/resources/quality/zyyx_plus/zyyx_plus_global_normal.inst.cfg b/resources/quality/zyyx_plus/zyyx_plus_global_normal.inst.cfg
index 579fc8551b..70341ff98e 100644
--- a/resources/quality/zyyx_plus/zyyx_plus_global_normal.inst.cfg
+++ b/resources/quality/zyyx_plus/zyyx_plus_global_normal.inst.cfg
@@ -13,3 +13,13 @@ global_quality = True
 [values]
 layer_height = 0.15
 infill_pattern = gyroid
+adhesion_type = brim
+infill_sparse_density = 15
+raft_airgap = 0.15
+retraction_amount = 1.2
+retraction_speed = 20
+speed_print = 50
+speed_wall = =math.ceil(speed_print * 22 / 50)
+speed_wall_x = =math.ceil(speed_print * 33 / 50)
+top_bottom_thickness = 1.0
+wall_thickness = 1.2
\ No newline at end of file