mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2026-02-01 13:50:42 -07:00
Examples Customizations
This commit is contained in:
GitHub Actions
parent
86bcdf9523
commit
eca0861c4e
820 changed files with 43726 additions and 42956 deletions
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "gCreate/gMax1.5+"
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
|
|
@ -61,14 +63,18 @@
|
|||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(MarlinFirmware)" // Original author or contributor.
|
||||
#define STRING_CONFIG_H_AUTHOR "(@Roxy-3D)" // Original author or contributor.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
// @section machine
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
//#define MOTHERBOARD BOARD_RAMPS_14_EEF
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB // gMax users please note: This is a Roxy modification. I print on glass and
|
||||
// use Marlin to control the bed temperature. So, if you have a single nozzle
|
||||
// machine, this will work fine for you. Just set the TEMP_SENSOR_BED to 0 down
|
||||
// below so Marlin doesn't mess with the bed temp.
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
|
@ -135,7 +141,7 @@
|
|||
//#define BLUETOOTH
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
#define CUSTOM_MACHINE_NAME "gMax"
|
||||
//#define CONFIGURABLE_MACHINE_NAME // Add G-code M550 to set/report the machine name
|
||||
|
||||
// Printer's unique ID, used by some programs to differentiate between machines.
|
||||
|
|
@ -588,7 +594,7 @@
|
|||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
|
|
@ -596,8 +602,10 @@
|
|||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_6 0
|
||||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_BED 75 // gMax-1.5+ users please note: This is a Roxy modification to the printer. I want
|
||||
// to print on glass. And I'm using a 400mm x 400mm silicon heat pad powered through
|
||||
// a Fortek SSR to do it. If you are using an unaltered gCreate machine, this needs
|
||||
// to be set to 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
|
|
@ -627,9 +635,9 @@
|
|||
#endif
|
||||
|
||||
#if HAS_E_TEMP_SENSOR
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
#define TEMP_RESIDENCY_TIME 16 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 5 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 12 // (°C) Temperature proximity considered "close enough" to the target
|
||||
#endif
|
||||
|
||||
#if TEMP_SENSOR_BED
|
||||
|
|
@ -678,15 +686,15 @@
|
|||
// Above this temperature the heater will be switched off.
|
||||
// This can protect components from overheating, but NOT from shorts and failures.
|
||||
// (Use MINTEMP for thermistor short/failure protection.)
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
#define HEATER_4_MAXTEMP 275
|
||||
#define HEATER_5_MAXTEMP 275
|
||||
#define HEATER_6_MAXTEMP 275
|
||||
#define HEATER_7_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
#define HEATER_0_MAXTEMP 245
|
||||
#define HEATER_1_MAXTEMP 245
|
||||
#define HEATER_2_MAXTEMP 245
|
||||
#define HEATER_3_MAXTEMP 245
|
||||
#define HEATER_4_MAXTEMP 245
|
||||
#define HEATER_5_MAXTEMP 245
|
||||
#define HEATER_6_MAXTEMP 245
|
||||
#define HEATER_7_MAXTEMP 245
|
||||
#define BED_MAXTEMP 115
|
||||
#define CHAMBER_MAXTEMP 60
|
||||
|
||||
/**
|
||||
|
|
@ -725,16 +733,17 @@
|
|||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
// gMax J-Head
|
||||
#if ENABLED(PID_PARAMS_PER_HOTEND)
|
||||
// Specify up to one value per hotend here, according to your setup.
|
||||
// If there are fewer values, the last one applies to the remaining hotends.
|
||||
#define DEFAULT_KP_LIST { 22.20, 22.20 }
|
||||
#define DEFAULT_KI_LIST { 1.08, 1.08 }
|
||||
#define DEFAULT_KD_LIST { 114.00, 114.00 }
|
||||
#define DEFAULT_KP_LIST { 15.35, 15.35 }
|
||||
#define DEFAULT_KI_LIST { 0.85, 0.85 }
|
||||
#define DEFAULT_KD_LIST { 69.45, 69.45 }
|
||||
#else
|
||||
#define DEFAULT_KP 22.20
|
||||
#define DEFAULT_KI 1.08
|
||||
#define DEFAULT_KD 114.00
|
||||
#define DEFAULT_KP 15.35
|
||||
#define DEFAULT_KI 0.85
|
||||
#define DEFAULT_KD 69.45
|
||||
#endif
|
||||
#else
|
||||
#define BANG_MAX 255 // Limit hotend current while in bang-bang mode; 255=full current
|
||||
|
|
@ -823,7 +832,7 @@
|
|||
*
|
||||
* With this option disabled, bang-bang will be used. BED_LIMIT_SWITCHING enables hysteresis.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
|
|
@ -832,9 +841,9 @@
|
|||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_BED_KP 10.00
|
||||
#define DEFAULT_BED_KI 0.023
|
||||
#define DEFAULT_BED_KD 305.4
|
||||
#define DEFAULT_BED_KP 135.44
|
||||
#define DEFAULT_BED_KI 24.60
|
||||
#define DEFAULT_BED_KD 186.40
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#else
|
||||
|
|
@ -1224,12 +1233,12 @@
|
|||
// @section endstops
|
||||
|
||||
// Enable pullup for all endstops to prevent a floating state
|
||||
#define ENDSTOPPULLUPS
|
||||
//#define ENDSTOPPULLUPS
|
||||
#if DISABLED(ENDSTOPPULLUPS)
|
||||
// Disable ENDSTOPPULLUPS to set pullups individually
|
||||
//#define ENDSTOPPULLUP_XMIN
|
||||
//#define ENDSTOPPULLUP_YMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
//#define ENDSTOPPULLUP_IMIN
|
||||
//#define ENDSTOPPULLUP_JMIN
|
||||
//#define ENDSTOPPULLUP_KMIN
|
||||
|
|
@ -1277,10 +1286,10 @@
|
|||
* Endstop "Hit" State
|
||||
* Set to the state (HIGH or LOW) that applies to each endstop.
|
||||
*/
|
||||
#define X_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define X_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define X_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE LOW
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define I_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
|
|
@ -1343,7 +1352,7 @@
|
|||
* Override with M92 (when enabled below)
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 96 }
|
||||
|
||||
/**
|
||||
* Enable support for M92. Disable to save at least ~530 bytes of flash.
|
||||
|
|
@ -1355,7 +1364,7 @@
|
|||
* Override with M203
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 500, 500, 25, 25 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
|
|
@ -1368,7 +1377,7 @@
|
|||
* Override with M201
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 800, 800, 700, 10000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
|
|
@ -1383,9 +1392,9 @@
|
|||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 400 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
* Default Jerk limits (mm/s)
|
||||
|
|
@ -1397,10 +1406,10 @@
|
|||
*/
|
||||
//#define CLASSIC_JERK
|
||||
#if ENABLED(CLASSIC_JERK)
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
#define DEFAULT_EJERK 5.0
|
||||
#define DEFAULT_XJERK 8.5
|
||||
#define DEFAULT_YJERK 8.5
|
||||
#define DEFAULT_ZJERK 0.7
|
||||
#define DEFAULT_EJERK 4.0
|
||||
//#define DEFAULT_IJERK 0.3
|
||||
//#define DEFAULT_JJERK 0.3
|
||||
//#define DEFAULT_KJERK 0.3
|
||||
|
|
@ -1424,7 +1433,7 @@
|
|||
* https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
|
||||
*/
|
||||
#if DISABLED(CLASSIC_JERK)
|
||||
#define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
|
||||
#define JUNCTION_DEVIATION_MM 0.058 // (mm) Distance from real junction edge
|
||||
#define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
|
||||
// for small segments (< 1mm) with large junction angles (> 135°).
|
||||
#endif
|
||||
|
|
@ -1518,7 +1527,7 @@
|
|||
/**
|
||||
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
|
||||
*/
|
||||
//#define BLTOUCH
|
||||
#define BLTOUCH
|
||||
|
||||
/**
|
||||
* MagLev V4 probe by MDD
|
||||
|
|
@ -1707,7 +1716,7 @@
|
|||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } // (mm) X, Y, Z distance from Nozzle tip to Probe trigger-point
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -17, -10, -0.25 } // (mm) X, Y, Z distance from Nozzle tip to Probe trigger-point
|
||||
|
||||
// Enable and set to use a specific tool for probing. Disable to allow any tool.
|
||||
#define PROBING_TOOL 0
|
||||
|
|
@ -1719,14 +1728,14 @@
|
|||
|
||||
// Most probes should stay away from the edges of the bed, but
|
||||
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
|
||||
#define PROBING_MARGIN 10
|
||||
#define PROBING_MARGIN 45
|
||||
|
||||
// X and Y axis travel speed between probes.
|
||||
// Leave undefined to use the average of the current XY homing feedrate.
|
||||
#define XY_PROBE_FEEDRATE (133*60) // (mm/min)
|
||||
#define XY_PROBE_FEEDRATE (125*60) // (mm/min)
|
||||
|
||||
// Feedrate for the first approach when double-probing (MULTIPLE_PROBING == 2)
|
||||
#define Z_PROBE_FEEDRATE_FAST (4*60) // (mm/min)
|
||||
#define Z_PROBE_FEEDRATE_FAST (14*60) // (mm/min)
|
||||
|
||||
// Feedrate for the "accurate" probe of each point
|
||||
#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2) // (mm/min)
|
||||
|
|
@ -1794,11 +1803,11 @@
|
|||
* Example: 'M851 Z-5' with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: 'M851 Z+1' with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // (mm) Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // (mm) Z Clearance between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // (mm) Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 6 // (mm) Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // (mm) Z Clearance between multiple probes
|
||||
#define Z_PROBE_ERROR_TOLERANCE 3 // (mm) Tolerance for early trigger (<= -probe.offset.z + ZPET)
|
||||
//#define Z_AFTER_PROBING 5 // (mm) Z position after probing is done
|
||||
//#define Z_AFTER_PROBING 6 // (mm) Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // (mm) Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
|
|
@ -1811,7 +1820,7 @@
|
|||
//#define PROBE_OFFSET_ZMAX 20 // (mm)
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// Before deploy/stow pause for user confirmation
|
||||
//#define PAUSE_BEFORE_DEPLOY_STOW
|
||||
|
|
@ -1878,9 +1887,9 @@
|
|||
// @section stepper drivers
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
//#define INVERT_I_DIR false
|
||||
//#define INVERT_J_DIR false
|
||||
//#define INVERT_K_DIR false
|
||||
|
|
@ -1910,7 +1919,7 @@
|
|||
*/
|
||||
//#define Z_IDLE_HEIGHT Z_HOME_POS
|
||||
|
||||
//#define Z_CLEARANCE_FOR_HOMING 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_CLEARANCE_FOR_HOMING 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// You'll need this much clearance above Z_MAX_POS to avoid grinding.
|
||||
|
||||
//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing (if Z was homed)
|
||||
|
|
@ -1921,7 +1930,7 @@
|
|||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Y_HOME_DIR 1
|
||||
#define Z_HOME_DIR -1
|
||||
//#define I_HOME_DIR -1
|
||||
//#define J_HOME_DIR -1
|
||||
|
|
@ -1948,8 +1957,9 @@
|
|||
// @section geometry
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 200
|
||||
#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 420 // These numbers are not accurate for an unaltered gMax 1.5+ printer. My print bed
|
||||
#define Y_BED_SIZE 420 // is inset a noticable amount from the edge of the bed. Combined with the inset,
|
||||
// the nozzle can reach all cordinates of the mesh.
|
||||
|
||||
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
|
|
@ -1957,7 +1967,7 @@
|
|||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 500
|
||||
//#define I_MIN_POS 0
|
||||
//#define I_MAX_POS 50
|
||||
//#define J_MIN_POS 0
|
||||
|
|
@ -1981,7 +1991,7 @@
|
|||
*/
|
||||
|
||||
// Min software endstops constrain movement within minimum coordinate bounds
|
||||
#define MIN_SOFTWARE_ENDSTOPS
|
||||
//#define MIN_SOFTWARE_ENDSTOPS
|
||||
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
|
||||
#define MIN_SOFTWARE_ENDSTOP_X
|
||||
#define MIN_SOFTWARE_ENDSTOP_Y
|
||||
|
|
@ -2027,7 +2037,7 @@
|
|||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
|
|
@ -2174,7 +2184,7 @@
|
|||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
|
|
@ -2194,7 +2204,7 @@
|
|||
* these options to restore the prior leveling state or to always enable
|
||||
* leveling immediately after G28.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define ENABLE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
|
|
@ -2211,7 +2221,7 @@
|
|||
* Turn on with the command 'M111 S32'.
|
||||
* NOTE: Requires a lot of flash!
|
||||
*/
|
||||
//#define DEBUG_LEVELING_FEATURE
|
||||
#define DEBUG_LEVELING_FEATURE
|
||||
|
||||
#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, PROBE_MANUALLY)
|
||||
// Set a height for the start of manual adjustment
|
||||
|
|
@ -2246,10 +2256,10 @@
|
|||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.5 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.3 // (mm) Default layer height for G26.
|
||||
#define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for G26.
|
||||
#define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for G26.
|
||||
#define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for G26 XY moves.
|
||||
|
|
@ -2292,9 +2302,9 @@
|
|||
//========================= Unified Bed Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
|
||||
#define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
|
||||
#define MESH_INSET 45 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
|
|
@ -2415,16 +2425,16 @@
|
|||
* - Allows Z homing only when XY positions are known and trusted.
|
||||
* - If stepper drivers sleep, XY homing may be required again before Z homing.
|
||||
*/
|
||||
//#define Z_SAFE_HOMING
|
||||
#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT X_CENTER // (mm) X point for Z homing
|
||||
#define Z_SAFE_HOMING_Y_POINT Y_CENTER // (mm) Y point for Z homing
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2 - 8) // (mm) X point for Z homing
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2 - 4) // (mm) Y point for Z homing
|
||||
//#define Z_SAFE_HOMING_POINT_ABSOLUTE // Ignore home offsets (M206) for Z homing position
|
||||
#endif
|
||||
|
||||
// Homing speeds (linear=mm/min, rotational=°/min)
|
||||
#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
|
||||
#define HOMING_FEEDRATE_MM_M { (60*60), (60*60), (14*60) }
|
||||
|
||||
// Edit homing feedrates with M210 and MarlinUI menu items
|
||||
//#define EDITABLE_HOMING_FEEDRATE
|
||||
|
|
@ -2505,7 +2515,7 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
|
|
@ -2522,7 +2532,7 @@
|
|||
// When enabled Marlin will send a busy status message to the host
|
||||
// every couple of seconds when it can't accept commands.
|
||||
//
|
||||
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
//#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||||
#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
|
||||
|
||||
|
|
@ -2544,13 +2554,13 @@
|
|||
// Preheat Constants - Up to 10 are supported without changes
|
||||
//
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_HOTEND 200
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_TEMP_CHAMBER 35
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_HOTEND 230
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_TEMP_CHAMBER 35
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
|
@ -2568,7 +2578,7 @@
|
|||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
|
|
@ -2750,7 +2760,7 @@
|
|||
* SD Card support is disabled by default. If your controller has an SD slot,
|
||||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: ENABLE CRC
|
||||
|
|
@ -2758,7 +2768,7 @@
|
|||
* Use CRC checks and retries on the SD communication.
|
||||
*/
|
||||
#if ENABLED(SDSUPPORT)
|
||||
//#define SD_CHECK_AND_RETRY
|
||||
#define SD_CHECK_AND_RETRY
|
||||
#endif
|
||||
|
||||
// @section interface
|
||||
|
|
@ -2821,13 +2831,13 @@
|
|||
// This option overrides the default number of encoder pulses needed to
|
||||
// produce one step. Should be increased for high-resolution encoders.
|
||||
//
|
||||
//#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_PULSES_PER_STEP 1
|
||||
|
||||
//
|
||||
// Use this option to override the number of step signals required to
|
||||
// move between next/prev menu items.
|
||||
//
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 5
|
||||
|
||||
/**
|
||||
* Encoder Direction Options
|
||||
|
|
@ -3082,7 +3092,7 @@
|
|||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// K.3D Full Graphic Smart Controller
|
||||
|
|
@ -3776,12 +3786,12 @@
|
|||
* Set this manually if there are extra servos needing manual control.
|
||||
* Set to 0 to turn off servo support.
|
||||
*/
|
||||
//#define NUM_SERVOS 3 // Note: Servo index starts with 0 for M280-M282 commands
|
||||
#define NUM_SERVOS 2 // Note: Servo index starts with 0 for M280-M282 commands
|
||||
|
||||
// (ms) Delay before the next move will start, to give the servo time to reach its target angle.
|
||||
// 300ms is a good value but you can try less delay.
|
||||
// If the servo can't reach the requested position, increase it.
|
||||
#define SERVO_DELAY { 300 }
|
||||
#define SERVO_DELAY { 300, 300 }
|
||||
|
||||
// Only power servos during movement, otherwise leave off to prevent jitter
|
||||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
|
|
|||
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "gCreate/gMax1.5+"
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
|
|
@ -308,8 +310,8 @@
|
|||
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ALL(HAS_HOTEND, THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // (seconds)
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // (°C)
|
||||
#define THERMAL_PROTECTION_PERIOD 50 // (seconds)
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 3 // (°C)
|
||||
|
||||
//#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
|
||||
#if ENABLED(ADAPTIVE_FAN_SLOWING)
|
||||
|
|
@ -331,7 +333,7 @@
|
|||
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
|
||||
* below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 40 // (seconds)
|
||||
#define WATCH_TEMP_PERIOD 50 // (seconds)
|
||||
#define WATCH_TEMP_INCREASE 2 // (°C)
|
||||
#endif
|
||||
|
||||
|
|
@ -339,7 +341,7 @@
|
|||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if TEMP_SENSOR_BED && ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // (seconds)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 50 // (seconds)
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // (°C)
|
||||
|
||||
/**
|
||||
|
|
@ -473,11 +475,6 @@
|
|||
#define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
|
||||
#endif
|
||||
#endif
|
||||
#if ENABLED(PID_PARAMS_PER_HOTEND)
|
||||
// Specify up to one value per hotend here, according to your setup.
|
||||
// If there are fewer values, the last one applies to the remaining hotends.
|
||||
#define DEFAULT_KF_LIST { DEFAULT_KF, DEFAULT_KF }
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -1089,7 +1086,7 @@
|
|||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
||||
#define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
|
||||
|
|
@ -1319,7 +1316,7 @@
|
|||
* Enable DISABLE_IDLE_* to shut down axis steppers after an idle period.
|
||||
* The default timeout duration can be overridden with M18 and M84. Set to 0 for No Timeout.
|
||||
*/
|
||||
#define DEFAULT_STEPPER_TIMEOUT_SEC 120
|
||||
#define DEFAULT_STEPPER_TIMEOUT_SEC 0 // usually set to 120 seconds
|
||||
#define DISABLE_IDLE_X
|
||||
#define DISABLE_IDLE_Y
|
||||
#define DISABLE_IDLE_Z // Disable if the nozzle could fall onto your printed part!
|
||||
|
|
@ -1680,7 +1677,7 @@
|
|||
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
|
||||
#endif
|
||||
#if ANY(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE, HAS_MARLINUI_HD44780, HAS_GRAPHICAL_TFT)
|
||||
//#define SHOW_CUSTOM_BOOTSCREEN // Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
#define SHOW_CUSTOM_BOOTSCREEN // Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
|
@ -1835,7 +1832,7 @@
|
|||
|
||||
//#define MEDIA_MENU_AT_TOP // Force the media menu to be listed on the top of the main menu
|
||||
|
||||
#define EVENT_GCODE_SD_ABORT "G28XY" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
|
||||
#define EVENT_GCODE_SD_ABORT "G27" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
|
||||
|
||||
#if ENABLED(PRINTER_EVENT_LEDS)
|
||||
#define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
|
||||
|
|
@ -1915,21 +1912,17 @@
|
|||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#if ENABLED(SDSORT_USES_RAM)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#if ENABLED(SDSORT_CACHE_NAMES)
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#endif
|
||||
#endif
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#endif
|
||||
|
||||
// Allow international symbols in long filenames. To display correctly, the
|
||||
|
|
@ -1954,7 +1947,7 @@
|
|||
//#define SD_ABORT_ON_ENDSTOP_HIT_GCODE "G28XY" // G-code to run on endstop hit (e.g., "G28XY" or "G27")
|
||||
#endif
|
||||
|
||||
//#define SD_REPRINT_LAST_SELECTED_FILE // On print completion open the LCD Menu and select the same file
|
||||
#define SD_REPRINT_LAST_SELECTED_FILE // On print completion open the LCD Menu and select the same file
|
||||
|
||||
//#define AUTO_REPORT_SD_STATUS // Auto-report media status with 'M27 S<seconds>'
|
||||
|
||||
|
|
@ -2392,7 +2385,7 @@
|
|||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define EP_BABYSTEPPING // M293/M294 babystepping with EMERGENCY_PARSER support
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
|
|
@ -2400,10 +2393,10 @@
|
|||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
//#define BABYSTEP_INVERT_Z // Enable if Z babysteps should go the other way
|
||||
//#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 3 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 3 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // (ms) Maximum interval between clicks.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
|
|
@ -2511,9 +2504,9 @@
|
|||
* Override if the automatically selected points are inadequate.
|
||||
*/
|
||||
#if NEEDS_THREE_PROBE_POINTS
|
||||
//#define PROBE_PT_1 { 15, 180 } // (mm) { x, y }
|
||||
//#define PROBE_PT_2 { 15, 20 }
|
||||
//#define PROBE_PT_3 { 170, 20 }
|
||||
#define PROBE_PT_1 { 53, 323 } // (mm) { x, y }
|
||||
#define PROBE_PT_2 { 53, 63 }
|
||||
#define PROBE_PT_3 { 348, 211 }
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -2779,7 +2772,7 @@
|
|||
* - Other output doesn't need to be that speedy.
|
||||
* :[0, 2, 4, 8, 16, 32, 64, 128, 256]
|
||||
*/
|
||||
#define TX_BUFFER_SIZE 0
|
||||
#define TX_BUFFER_SIZE 32
|
||||
|
||||
/**
|
||||
* Host Receive Buffer Size
|
||||
|
|
@ -2875,7 +2868,7 @@
|
|||
* For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
|
||||
* Otherwise, adjust according to your client and font.
|
||||
*/
|
||||
#define PROPORTIONAL_FONT_RATIO 1.0
|
||||
#define PROPORTIONAL_FONT_RATIO 1.5
|
||||
|
||||
// @section extras
|
||||
|
||||
|
|
@ -3052,7 +3045,7 @@
|
|||
*
|
||||
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
|
|
@ -3092,7 +3085,7 @@
|
|||
//#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again.
|
||||
//#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
|
|
@ -4155,7 +4148,7 @@
|
|||
* workspace offsets to slightly optimize performance.
|
||||
* G92 will revert to its behavior from Marlin 1.0.
|
||||
*/
|
||||
//#define NO_WORKSPACE_OFFSETS
|
||||
#define NO_WORKSPACE_OFFSETS
|
||||
|
||||
/**
|
||||
* Disable M206 and M428 if you don't need home offsets.
|
||||
|
|
@ -4226,13 +4219,13 @@
|
|||
//#define MAIN_MENU_ITEM_2_CONFIRM
|
||||
//#define MAIN_MENU_ITEM_2_IMMEDIATE
|
||||
|
||||
//#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
|
||||
//#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
|
||||
#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
|
||||
#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
|
||||
//#define MAIN_MENU_ITEM_3_CONFIRM
|
||||
//#define MAIN_MENU_ITEM_3_IMMEDIATE
|
||||
|
||||
//#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
|
||||
//#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
|
||||
#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
|
||||
#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
|
||||
//#define MAIN_MENU_ITEM_4_CONFIRM
|
||||
//#define MAIN_MENU_ITEM_4_IMMEDIATE
|
||||
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue