mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2026-01-31 13:20:42 -07:00
Examples Customizations
This commit is contained in:
GitHub Actions
parent
86bcdf9523
commit
eca0861c4e
820 changed files with 43726 additions and 42956 deletions
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "STM32/Black_STM32F407VET6"
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
|
|
@ -61,14 +63,14 @@
|
|||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(MarlinFirmware)" // Original author or contributor.
|
||||
#define STRING_CONFIG_H_AUTHOR "(Karl Andersson)" // Original author or contributor.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
// @section machine
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_BLACK_STM32F407VE
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
|
@ -81,7 +83,7 @@
|
|||
*
|
||||
* :[-1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9]
|
||||
*/
|
||||
#define SERIAL_PORT 0
|
||||
#define SERIAL_PORT -1
|
||||
|
||||
/**
|
||||
* Serial Port Baud Rate
|
||||
|
|
@ -103,7 +105,7 @@
|
|||
* Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
|
||||
* :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9]
|
||||
*/
|
||||
//#define SERIAL_PORT_2 -1
|
||||
#define SERIAL_PORT_2 1
|
||||
//#define BAUDRATE_2 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
|
||||
|
||||
/**
|
||||
|
|
@ -174,7 +176,7 @@
|
|||
//#define V_DRIVER_TYPE A4988
|
||||
//#define W_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
//#define E1_DRIVER_TYPE A4988
|
||||
#define E1_DRIVER_TYPE A4988
|
||||
//#define E2_DRIVER_TYPE A4988
|
||||
//#define E3_DRIVER_TYPE A4988
|
||||
//#define E4_DRIVER_TYPE A4988
|
||||
|
|
@ -228,7 +230,7 @@
|
|||
|
||||
// This defines the number of extruders
|
||||
// :[0, 1, 2, 3, 4, 5, 6, 7, 8]
|
||||
#define EXTRUDERS 1
|
||||
#define EXTRUDERS 2
|
||||
|
||||
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
|
||||
|
|
@ -589,7 +591,7 @@
|
|||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_1 1
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_4 0
|
||||
|
|
@ -598,7 +600,7 @@
|
|||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_CHAMBER 1
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
|
|
@ -1299,7 +1301,7 @@
|
|||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
#define ENDSTOP_INTERRUPTS_FEATURE
|
||||
|
||||
/**
|
||||
* Endstop Noise Threshold
|
||||
|
|
@ -1343,7 +1345,7 @@
|
|||
* Override with M92 (when enabled below)
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
|
||||
|
||||
/**
|
||||
* Enable support for M92. Disable to save at least ~530 bytes of flash.
|
||||
|
|
@ -2030,7 +2032,7 @@
|
|||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define NUM_RUNOUT_SENSORS 2 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
|
||||
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
|
|
@ -2074,7 +2076,7 @@
|
|||
// Commands to execute on filament runout.
|
||||
// With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
|
||||
// NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600 T%c"
|
||||
|
||||
// After a runout is detected, continue printing this length of filament
|
||||
// before executing the runout script. Useful for a sensor at the end of
|
||||
|
|
@ -2505,7 +2507,7 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
|
|
@ -3776,12 +3778,12 @@
|
|||
* Set this manually if there are extra servos needing manual control.
|
||||
* Set to 0 to turn off servo support.
|
||||
*/
|
||||
//#define NUM_SERVOS 3 // Note: Servo index starts with 0 for M280-M282 commands
|
||||
#define NUM_SERVOS 2 // Note: Servo index starts with 0 for M280-M282 commands
|
||||
|
||||
// (ms) Delay before the next move will start, to give the servo time to reach its target angle.
|
||||
// 300ms is a good value but you can try less delay.
|
||||
// If the servo can't reach the requested position, increase it.
|
||||
#define SERVO_DELAY { 300 }
|
||||
#define SERVO_DELAY { 300, 300 }
|
||||
|
||||
// Only power servos during movement, otherwise leave off to prevent jitter
|
||||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
|
|
|||
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "STM32/Black_STM32F407VET6"
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
|
|
@ -473,11 +475,6 @@
|
|||
#define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
|
||||
#endif
|
||||
#endif
|
||||
#if ENABLED(PID_PARAMS_PER_HOTEND)
|
||||
// Specify up to one value per hotend here, according to your setup.
|
||||
// If there are fewer values, the last one applies to the remaining hotends.
|
||||
#define DEFAULT_KF_LIST { DEFAULT_KF, DEFAULT_KF }
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -699,8 +696,8 @@
|
|||
* Multiple extruders can be assigned to the same pin in which case
|
||||
* the fan will turn on when any selected extruder is above the threshold.
|
||||
*/
|
||||
#define E0_AUTO_FAN_PIN -1
|
||||
#define E1_AUTO_FAN_PIN -1
|
||||
#define E0_AUTO_FAN_PIN FAN1_PIN
|
||||
#define E1_AUTO_FAN_PIN FAN2_PIN
|
||||
#define E2_AUTO_FAN_PIN -1
|
||||
#define E3_AUTO_FAN_PIN -1
|
||||
#define E4_AUTO_FAN_PIN -1
|
||||
|
|
@ -1089,7 +1086,7 @@
|
|||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
||||
#define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
|
||||
|
|
@ -1915,21 +1912,17 @@
|
|||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#if ENABLED(SDSORT_USES_RAM)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#if ENABLED(SDSORT_CACHE_NAMES)
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#endif
|
||||
#endif
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#endif
|
||||
|
||||
// Allow international symbols in long filenames. To display correctly, the
|
||||
|
|
|
|||
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "STM32/STM32F103RE"
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
|
|
@ -61,14 +63,14 @@
|
|||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(MarlinFirmware)" // Original author or contributor.
|
||||
#define STRING_CONFIG_H_AUTHOR "(Victor Perez)" // Original author or contributor.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
// @section machine
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_STM32F103RE
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
|
@ -81,7 +83,7 @@
|
|||
*
|
||||
* :[-1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9]
|
||||
*/
|
||||
#define SERIAL_PORT 0
|
||||
#define SERIAL_PORT -1
|
||||
|
||||
/**
|
||||
* Serial Port Baud Rate
|
||||
|
|
@ -135,7 +137,7 @@
|
|||
//#define BLUETOOTH
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
#define CUSTOM_MACHINE_NAME "CTC i3 Pro B"
|
||||
//#define CONFIGURABLE_MACHINE_NAME // Add G-code M550 to set/report the machine name
|
||||
|
||||
// Printer's unique ID, used by some programs to differentiate between machines.
|
||||
|
|
@ -605,8 +607,8 @@
|
|||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
#define DUMMY_THERMISTOR_998_VALUE 25
|
||||
#define DUMMY_THERMISTOR_999_VALUE 100
|
||||
#define DUMMY_THERMISTOR_998_VALUE 60
|
||||
#define DUMMY_THERMISTOR_999_VALUE 205
|
||||
|
||||
// Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1 / 2 / BED
|
||||
#if TEMP_SENSOR_IS_MAX_TC(0)
|
||||
|
|
@ -715,7 +717,7 @@
|
|||
#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning
|
||||
//#define MPCTEMP // See https://marlinfw.org/docs/features/model_predictive_control.html
|
||||
|
||||
#define PID_MAX 255 // Limit hotend current while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_MAX 180 // Limit hotend current while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
|
|
@ -737,7 +739,7 @@
|
|||
#define DEFAULT_KD 114.00
|
||||
#endif
|
||||
#else
|
||||
#define BANG_MAX 255 // Limit hotend current while in bang-bang mode; 255=full current
|
||||
#define BANG_MAX 180 // Limit hotend current while in bang-bang mode; 255=full current
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -756,7 +758,7 @@
|
|||
//#define MPC_EDIT_MENU // Add MPC editing to the "Advanced Settings" menu. (~1.3K bytes of flash)
|
||||
//#define MPC_AUTOTUNE_MENU // Add MPC auto-tuning to the "Advanced Settings" menu. (~350 bytes of flash)
|
||||
|
||||
#define MPC_MAX 255 // (0..255) Current to nozzle while MPC is active.
|
||||
#define MPC_MAX 180 // (0..255) Current to nozzle while MPC is active.
|
||||
#define MPC_HEATER_POWER { 40.0f } // (W) Nominal heat cartridge powers.
|
||||
//#define MPC_PTC // Hotend power changes with temperature (e.g., PTC heat cartridges).
|
||||
#if ENABLED(MPC_PTC)
|
||||
|
|
@ -931,8 +933,8 @@
|
|||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
//#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
|
||||
#endif
|
||||
|
||||
// @section safety
|
||||
|
|
@ -1278,11 +1280,11 @@
|
|||
* Set to the state (HIGH or LOW) that applies to each endstop.
|
||||
*/
|
||||
#define X_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define X_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define X_MAX_ENDSTOP_HIT_STATE LOW
|
||||
#define Y_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE LOW
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE LOW
|
||||
#define I_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define I_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define J_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
|
|
@ -1343,7 +1345,7 @@
|
|||
* Override with M92 (when enabled below)
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105.0 }
|
||||
|
||||
/**
|
||||
* Enable support for M92. Disable to save at least ~530 bytes of flash.
|
||||
|
|
@ -1355,7 +1357,7 @@
|
|||
* Override with M203
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
|
|
@ -1368,7 +1370,7 @@
|
|||
* Override with M201
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 1400, 1400, 100, 80000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
|
|
@ -1383,8 +1385,8 @@
|
|||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_ACCELERATION 1400 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
|
|
@ -1397,8 +1399,8 @@
|
|||
*/
|
||||
//#define CLASSIC_JERK
|
||||
#if ENABLED(CLASSIC_JERK)
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_XJERK 13.0
|
||||
#define DEFAULT_YJERK 13.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
#define DEFAULT_EJERK 5.0
|
||||
//#define DEFAULT_IJERK 0.3
|
||||
|
|
@ -1424,7 +1426,7 @@
|
|||
* https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
|
||||
*/
|
||||
#if DISABLED(CLASSIC_JERK)
|
||||
#define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
|
||||
#define JUNCTION_DEVIATION_MM 0.048 // (mm) Distance from real junction edge
|
||||
#define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
|
||||
// for small segments (< 1mm) with large junction angles (> 135°).
|
||||
#endif
|
||||
|
|
@ -1707,7 +1709,7 @@
|
|||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } // (mm) X, Y, Z distance from Nozzle tip to Probe trigger-point
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 } // (mm) X, Y, Z distance from Nozzle tip to Probe trigger-point
|
||||
|
||||
// Enable and set to use a specific tool for probing. Disable to allow any tool.
|
||||
#define PROBING_TOOL 0
|
||||
|
|
@ -1889,7 +1891,7 @@
|
|||
//#define INVERT_W_DIR false
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E0_DIR true
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
|
|
@ -1957,7 +1959,7 @@
|
|||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 180
|
||||
//#define I_MIN_POS 0
|
||||
//#define I_MAX_POS 50
|
||||
//#define J_MIN_POS 0
|
||||
|
|
@ -2505,9 +2507,9 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
|
||||
//#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
|
|
@ -2536,7 +2538,7 @@
|
|||
//
|
||||
// M149 Set temperature units support
|
||||
//
|
||||
//#define TEMPERATURE_UNITS_SUPPORT
|
||||
#define TEMPERATURE_UNITS_SUPPORT
|
||||
|
||||
// @section temperature presets
|
||||
|
||||
|
|
@ -2544,14 +2546,14 @@
|
|||
// Preheat Constants - Up to 10 are supported without changes
|
||||
//
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_TEMP_HOTEND 200
|
||||
#define PREHEAT_1_TEMP_BED 60
|
||||
#define PREHEAT_1_TEMP_CHAMBER 35
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_TEMP_HOTEND 220
|
||||
#define PREHEAT_2_TEMP_BED 100
|
||||
#define PREHEAT_2_TEMP_CHAMBER 35
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
|
|
@ -2750,7 +2752,7 @@
|
|||
* SD Card support is disabled by default. If your controller has an SD slot,
|
||||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: ENABLE CRC
|
||||
|
|
|
|||
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "STM32/STM32F103RE"
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
|
|
@ -473,11 +475,6 @@
|
|||
#define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
|
||||
#endif
|
||||
#endif
|
||||
#if ENABLED(PID_PARAMS_PER_HOTEND)
|
||||
// Specify up to one value per hotend here, according to your setup.
|
||||
// If there are fewer values, the last one applies to the remaining hotends.
|
||||
#define DEFAULT_KF_LIST { DEFAULT_KF, DEFAULT_KF }
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -1915,21 +1912,17 @@
|
|||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#if ENABLED(SDSORT_USES_RAM)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#if ENABLED(SDSORT_CACHE_NAMES)
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#endif
|
||||
#endif
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#endif
|
||||
|
||||
// Allow international symbols in long filenames. To display correctly, the
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue