mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2026-01-31 21:30:44 -07:00
Examples Customizations
This commit is contained in:
GitHub Actions
parent
86bcdf9523
commit
eca0861c4e
820 changed files with 43726 additions and 42956 deletions
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "Modix/Big60"
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
|
|
@ -61,14 +63,14 @@
|
|||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(MarlinFirmware)" // Original author or contributor.
|
||||
#define STRING_CONFIG_H_AUTHOR "(3DXtech)" // Original author or contributor.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
// @section machine
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_MKS_GEN_L
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
|
@ -135,7 +137,7 @@
|
|||
//#define BLUETOOTH
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
#define CUSTOM_MACHINE_NAME "ModixBig60"
|
||||
//#define CONFIGURABLE_MACHINE_NAME // Add G-code M550 to set/report the machine name
|
||||
|
||||
// Printer's unique ID, used by some programs to differentiate between machines.
|
||||
|
|
@ -588,7 +590,7 @@
|
|||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
|
|
@ -596,7 +598,7 @@
|
|||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_6 0
|
||||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
|
|
@ -678,7 +680,7 @@
|
|||
// Above this temperature the heater will be switched off.
|
||||
// This can protect components from overheating, but NOT from shorts and failures.
|
||||
// (Use MINTEMP for thermistor short/failure protection.)
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_0_MAXTEMP 315
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
|
|
@ -730,11 +732,11 @@
|
|||
// If there are fewer values, the last one applies to the remaining hotends.
|
||||
#define DEFAULT_KP_LIST { 22.20, 22.20 }
|
||||
#define DEFAULT_KI_LIST { 1.08, 1.08 }
|
||||
#define DEFAULT_KD_LIST { 114.00, 114.00 }
|
||||
#define DEFAULT_KD_LIST { 59.50, 59.50 }
|
||||
#else
|
||||
#define DEFAULT_KP 22.20
|
||||
#define DEFAULT_KI 1.08
|
||||
#define DEFAULT_KD 114.00
|
||||
#define DEFAULT_KD 59.50
|
||||
#endif
|
||||
#else
|
||||
#define BANG_MAX 255 // Limit hotend current while in bang-bang mode; 255=full current
|
||||
|
|
@ -931,8 +933,8 @@
|
|||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
//#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
|
||||
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
|
||||
#endif
|
||||
|
||||
// @section safety
|
||||
|
|
@ -1277,11 +1279,11 @@
|
|||
* Endstop "Hit" State
|
||||
* Set to the state (HIGH or LOW) that applies to each endstop.
|
||||
*/
|
||||
#define X_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define X_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define X_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE LOW
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define I_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define I_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
|
|
@ -1295,7 +1297,7 @@
|
|||
#define V_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define W_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define W_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MIN_PROBE_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MIN_PROBE_ENDSTOP_HIT_STATE LOW
|
||||
|
||||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||||
|
|
@ -1343,7 +1345,7 @@
|
|||
* Override with M92 (when enabled below)
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 200, 100, 2000, 418.50 }
|
||||
|
||||
/**
|
||||
* Enable support for M92. Disable to save at least ~530 bytes of flash.
|
||||
|
|
@ -1355,7 +1357,7 @@
|
|||
* Override with M203
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 200, 200, 5, 70 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
|
|
@ -1368,7 +1370,7 @@
|
|||
* Override with M201
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 100, 10000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
|
|
@ -1383,9 +1385,9 @@
|
|||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
* Default Jerk limits (mm/s)
|
||||
|
|
@ -1424,7 +1426,7 @@
|
|||
* https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
|
||||
*/
|
||||
#if DISABLED(CLASSIC_JERK)
|
||||
#define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
|
||||
#define JUNCTION_DEVIATION_MM 0.06 // (mm) Distance from real junction edge
|
||||
#define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle
|
||||
// for small segments (< 1mm) with large junction angles (> 135°).
|
||||
#endif
|
||||
|
|
@ -1437,7 +1439,7 @@
|
|||
*
|
||||
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
|
||||
*/
|
||||
//#define S_CURVE_ACCELERATION
|
||||
#define S_CURVE_ACCELERATION
|
||||
#if ENABLED(S_CURVE_ACCELERATION)
|
||||
// Define to use 4th instead of 6th order motion curve
|
||||
//#define S_CURVE_FACTOR 0.25 // Initial and final acceleration factor, ideally 0.1 to 0.4.
|
||||
|
|
@ -1496,7 +1498,7 @@
|
|||
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
|
||||
* (e.g., an inductive probe or a nozzle-based probe-switch.)
|
||||
*/
|
||||
//#define FIX_MOUNTED_PROBE
|
||||
#define FIX_MOUNTED_PROBE
|
||||
|
||||
/**
|
||||
* Use the nozzle as the probe, as with a conductive
|
||||
|
|
@ -1707,7 +1709,7 @@
|
|||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } // (mm) X, Y, Z distance from Nozzle tip to Probe trigger-point
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -34, 26, 0 } // (mm) X, Y, Z distance from Nozzle tip to Probe trigger-point
|
||||
|
||||
// Enable and set to use a specific tool for probing. Disable to allow any tool.
|
||||
#define PROBING_TOOL 0
|
||||
|
|
@ -1723,10 +1725,10 @@
|
|||
|
||||
// X and Y axis travel speed between probes.
|
||||
// Leave undefined to use the average of the current XY homing feedrate.
|
||||
#define XY_PROBE_FEEDRATE (133*60) // (mm/min)
|
||||
#define XY_PROBE_FEEDRATE (83*60) // (mm/min)
|
||||
|
||||
// Feedrate for the first approach when double-probing (MULTIPLE_PROBING == 2)
|
||||
#define Z_PROBE_FEEDRATE_FAST (4*60) // (mm/min)
|
||||
#define Z_PROBE_FEEDRATE_FAST (6*60) // (mm/min)
|
||||
|
||||
// Feedrate for the "accurate" probe of each point
|
||||
#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2) // (mm/min)
|
||||
|
|
@ -1777,7 +1779,7 @@
|
|||
* A total of 2 does fast/slow probes with a weighted average.
|
||||
* A total of 3 or more adds more slow probes, taking the average.
|
||||
*/
|
||||
//#define MULTIPLE_PROBING 2
|
||||
#define MULTIPLE_PROBING 2
|
||||
//#define EXTRA_PROBING 1
|
||||
|
||||
/**
|
||||
|
|
@ -1800,7 +1802,7 @@
|
|||
#define Z_PROBE_ERROR_TOLERANCE 3 // (mm) Tolerance for early trigger (<= -probe.offset.z + ZPET)
|
||||
//#define Z_AFTER_PROBING 5 // (mm) Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // (mm) Farthest distance below the trigger-point to go before stopping
|
||||
#define Z_PROBE_LOW_POINT -3 // (mm) Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
// For M851 provide ranges for adjusting the X, Y, and Z probe offsets
|
||||
//#define PROBE_OFFSET_XMIN -50 // (mm)
|
||||
|
|
@ -1811,7 +1813,7 @@
|
|||
//#define PROBE_OFFSET_ZMAX 20 // (mm)
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// Before deploy/stow pause for user confirmation
|
||||
//#define PAUSE_BEFORE_DEPLOY_STOW
|
||||
|
|
@ -1878,9 +1880,9 @@
|
|||
// @section stepper drivers
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
//#define INVERT_I_DIR false
|
||||
//#define INVERT_J_DIR false
|
||||
//#define INVERT_K_DIR false
|
||||
|
|
@ -1921,7 +1923,7 @@
|
|||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Y_HOME_DIR 1
|
||||
#define Z_HOME_DIR -1
|
||||
//#define I_HOME_DIR -1
|
||||
//#define J_HOME_DIR -1
|
||||
|
|
@ -1948,8 +1950,8 @@
|
|||
// @section geometry
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 200
|
||||
#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 600
|
||||
#define Y_BED_SIZE 600
|
||||
|
||||
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
|
|
@ -1957,7 +1959,7 @@
|
|||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 600
|
||||
//#define I_MIN_POS 0
|
||||
//#define I_MAX_POS 50
|
||||
//#define J_MIN_POS 0
|
||||
|
|
@ -2027,12 +2029,12 @@
|
|||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
|
||||
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
|
||||
#define FIL_RUNOUT_STATE HIGH // Pin state indicating that filament is NOT present.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
//#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder.
|
||||
|
|
@ -2079,7 +2081,7 @@
|
|||
// After a runout is detected, continue printing this length of filament
|
||||
// before executing the runout script. Useful for a sensor at the end of
|
||||
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
|
||||
//#define FILAMENT_RUNOUT_DISTANCE_MM 25
|
||||
#define FILAMENT_RUNOUT_DISTANCE_MM 100
|
||||
|
||||
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
|
||||
// Enable this option to use an encoder disc that toggles the runout pin
|
||||
|
|
@ -2174,7 +2176,7 @@
|
|||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
|
|
@ -2194,7 +2196,7 @@
|
|||
* these options to restore the prior leveling state or to always enable
|
||||
* leveling immediately after G28.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define ENABLE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
|
|
@ -2246,7 +2248,7 @@
|
|||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
|
||||
|
|
@ -2295,7 +2297,7 @@
|
|||
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
|
||||
#define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 15 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
|
||||
|
|
@ -2306,7 +2308,7 @@
|
|||
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
|
||||
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
|
||||
|
||||
//#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
|
||||
#define UBL_Z_RAISE_WHEN_OFF_MESH 0.0 // When the nozzle is off the mesh, this value is used
|
||||
// as the Z-Height correction value.
|
||||
|
||||
//#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
|
||||
|
|
@ -2348,22 +2350,22 @@
|
|||
* Add a bed leveling sub-menu for ABL or MBL.
|
||||
* Include a guided procedure if manual probing is enabled.
|
||||
*/
|
||||
//#define LCD_BED_LEVELING
|
||||
#define LCD_BED_LEVELING
|
||||
|
||||
#if ENABLED(LCD_BED_LEVELING)
|
||||
#define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
|
||||
#define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
|
||||
//#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#endif
|
||||
|
||||
// Add a menu item to move between bed corners for manual bed adjustment
|
||||
//#define LCD_BED_TRAMMING
|
||||
#define LCD_BED_TRAMMING
|
||||
|
||||
#if ENABLED(LCD_BED_TRAMMING)
|
||||
#define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
|
||||
#define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at tramming points
|
||||
#define BED_TRAMMING_Z_HOP 4.0 // (mm) Z raise between tramming points
|
||||
//#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner
|
||||
#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner
|
||||
//#define BED_TRAMMING_USE_PROBE
|
||||
#if ENABLED(BED_TRAMMING_USE_PROBE)
|
||||
#define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm)
|
||||
|
|
@ -2415,7 +2417,7 @@
|
|||
* - Allows Z homing only when XY positions are known and trusted.
|
||||
* - If stepper drivers sleep, XY homing may be required again before Z homing.
|
||||
*/
|
||||
//#define Z_SAFE_HOMING
|
||||
#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT X_CENTER // (mm) X point for Z homing
|
||||
|
|
@ -2424,7 +2426,7 @@
|
|||
#endif
|
||||
|
||||
// Homing speeds (linear=mm/min, rotational=°/min)
|
||||
#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
|
||||
#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (6*60) }
|
||||
|
||||
// Edit homing feedrates with M210 and MarlinUI menu items
|
||||
//#define EDITABLE_HOMING_FEEDRATE
|
||||
|
|
@ -2505,12 +2507,12 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
//#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
|
||||
#endif
|
||||
|
||||
|
|
@ -2568,11 +2570,11 @@
|
|||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 50), (Y_MIN_POS + 50), 10 }
|
||||
#define NOZZLE_PARK_MOVE 0 // Park motion: 0 = XY Move, 1 = X Only, 2 = Y Only, 3 = X before Y, 4 = Y before X
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
|
|
@ -2750,7 +2752,7 @@
|
|||
* SD Card support is disabled by default. If your controller has an SD slot,
|
||||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: ENABLE CRC
|
||||
|
|
@ -2877,7 +2879,7 @@
|
|||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
//#define INDIVIDUAL_AXIS_HOMING_SUBMENU
|
||||
|
||||
//
|
||||
|
|
@ -2886,7 +2888,7 @@
|
|||
// If you have a speaker that can produce tones, enable it here.
|
||||
// By default Marlin assumes you have a buzzer with a fixed frequency.
|
||||
//
|
||||
//#define SPEAKER
|
||||
#define SPEAKER
|
||||
|
||||
//
|
||||
// The duration and frequency for the UI feedback sound.
|
||||
|
|
@ -3082,7 +3084,7 @@
|
|||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// K.3D Full Graphic Smart Controller
|
||||
|
|
@ -3639,7 +3641,7 @@
|
|||
* which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
* is too low, you should also increment SOFT_PWM_SCALE.
|
||||
*/
|
||||
//#define FAN_SOFT_PWM
|
||||
#define FAN_SOFT_PWM
|
||||
|
||||
/**
|
||||
* Incrementing this by 1 will double the software PWM frequency, affecting heaters, and
|
||||
|
|
|
|||
|
|
@ -21,6 +21,8 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "Modix/Big60"
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
|
|
@ -309,13 +311,13 @@
|
|||
*/
|
||||
#if ALL(HAS_HOTEND, THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // (seconds)
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // (°C)
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 10 // (°C)
|
||||
|
||||
//#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
|
||||
#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
|
||||
#if ENABLED(ADAPTIVE_FAN_SLOWING)
|
||||
//#define REPORT_ADAPTIVE_FAN_SLOWING // Report fan slowing activity to the console
|
||||
#if ANY(MPCTEMP, PIDTEMP)
|
||||
//#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T
|
||||
#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
|
@ -473,11 +475,6 @@
|
|||
#define PID_FAN_SCALING_MIN_SPEED 10 // Minimum fan speed at which to enable PID_FAN_SCALING
|
||||
#endif
|
||||
#endif
|
||||
#if ENABLED(PID_PARAMS_PER_HOTEND)
|
||||
// Specify up to one value per hotend here, according to your setup.
|
||||
// If there are fewer values, the last one applies to the remaining hotends.
|
||||
#define DEFAULT_KF_LIST { DEFAULT_KF, DEFAULT_KF }
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -949,7 +946,7 @@
|
|||
//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
|
||||
//#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa
|
||||
|
||||
//#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
|
||||
//#define HOME_Z_FIRST // Home Z first. Requires a real endstop (not a probe).
|
||||
//#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
|
||||
|
|
@ -1089,7 +1086,7 @@
|
|||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
||||
#define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
|
||||
|
|
@ -1680,12 +1677,12 @@
|
|||
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
|
||||
#endif
|
||||
#if ANY(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE, HAS_MARLINUI_HD44780, HAS_GRAPHICAL_TFT)
|
||||
//#define SHOW_CUSTOM_BOOTSCREEN // Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
#define SHOW_CUSTOM_BOOTSCREEN // Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if HAS_MARLINUI_U8GLIB
|
||||
//#define CUSTOM_STATUS_SCREEN_IMAGE // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
|
||||
#define CUSTOM_STATUS_SCREEN_IMAGE // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
|
||||
#endif
|
||||
|
||||
//#define SOUND_MENU_ITEM // Add a mute option to the LCD menu
|
||||
|
|
@ -1700,10 +1697,10 @@
|
|||
#endif
|
||||
|
||||
// The timeout to return to the status screen from sub-menus
|
||||
//#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
|
||||
#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// Apply a timeout to low-priority status messages
|
||||
//#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
|
||||
|
|
@ -1756,10 +1753,10 @@
|
|||
#endif
|
||||
|
||||
// Add 'M73' to set print job progress, overrides Marlin's built-in estimate
|
||||
//#define SET_PROGRESS_MANUALLY
|
||||
#define SET_PROGRESS_MANUALLY
|
||||
#if ENABLED(SET_PROGRESS_MANUALLY)
|
||||
#define SET_PROGRESS_PERCENT // Add 'P' parameter to set percentage done
|
||||
#define SET_REMAINING_TIME // Add 'R' parameter to set remaining time
|
||||
//#define SET_REMAINING_TIME // Add 'R' parameter to set remaining time
|
||||
//#define SET_INTERACTION_TIME // Add 'C' parameter to set time until next filament change or other user interaction
|
||||
//#define M73_REPORT // Report M73 values to host
|
||||
#if ALL(M73_REPORT, HAS_MEDIA)
|
||||
|
|
@ -1915,32 +1912,28 @@
|
|||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#if ENABLED(SDSORT_USES_RAM)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#if ENABLED(SDSORT_CACHE_NAMES)
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#endif
|
||||
#endif
|
||||
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1>
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
// Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.
|
||||
#define SDSORT_QUICK true // Use Quick Sort as a sorting algorithm. Otherwise use Bubble Sort.
|
||||
#endif
|
||||
|
||||
// Allow international symbols in long filenames. To display correctly, the
|
||||
// LCD's font must contain the characters. Check your selected LCD language.
|
||||
//#define UTF_FILENAME_SUPPORT
|
||||
|
||||
//#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
|
||||
#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
|
||||
//#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
|
||||
//#define M20_TIMESTAMP_SUPPORT // Include timestamps by adding the 'T' flag to M20 commands
|
||||
|
||||
//#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
|
||||
#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
|
||||
|
||||
//#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!)
|
||||
|
||||
|
|
@ -1956,7 +1949,7 @@
|
|||
|
||||
//#define SD_REPRINT_LAST_SELECTED_FILE // On print completion open the LCD Menu and select the same file
|
||||
|
||||
//#define AUTO_REPORT_SD_STATUS // Auto-report media status with 'M27 S<seconds>'
|
||||
#define AUTO_REPORT_SD_STATUS // Auto-report media status with 'M27 S<seconds>'
|
||||
|
||||
/**
|
||||
* Support for USB thumb drives using an Arduino USB Host Shield or
|
||||
|
|
@ -2392,18 +2385,18 @@
|
|||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define EP_BABYSTEPPING // M293/M294 babystepping with EMERGENCY_PARSER support
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
//#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement)
|
||||
#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
//#define BABYSTEP_INVERT_Z // Enable if Z babysteps should go the other way
|
||||
//#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // (ms) Maximum interval between clicks.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
|
|
@ -2415,14 +2408,14 @@
|
|||
|
||||
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
|
||||
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
//#define BABYSTEP_GLOBAL_Z // Combine M424 Z and Babystepping
|
||||
|
||||
#if ANY(BABYSTEP_ZPROBE_OFFSET, BABYSTEP_GLOBAL_Z)
|
||||
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
||||
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
|
||||
#endif
|
||||
//#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
|
@ -2443,13 +2436,13 @@
|
|||
*
|
||||
* See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
|
||||
*/
|
||||
//#define LIN_ADVANCE
|
||||
#define LIN_ADVANCE
|
||||
|
||||
#if ANY(LIN_ADVANCE, FT_MOTION)
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_K { 0.22 } // (mm) Compression length per 1mm/s extruder speed, per extruder. Override with 'M900 T<tool> K<mm>'.
|
||||
#define ADVANCE_K { 0.0 } // (mm) Compression length per 1mm/s extruder speed, per extruder. Override with 'M900 T<tool> K<mm>'.
|
||||
#else
|
||||
#define ADVANCE_K 0.22 // (mm) Compression length for all extruders. Override with 'M900 K<mm>'.
|
||||
#define ADVANCE_K 0.0 // (mm) Compression length for all extruders. Override with 'M900 K<mm>'.
|
||||
#endif
|
||||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with 'M900 L'.
|
||||
#endif
|
||||
|
|
@ -2664,7 +2657,7 @@
|
|||
#endif
|
||||
|
||||
// G5 Bézier Curve Support with XYZE destination and IJPQ offsets
|
||||
//#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes
|
||||
#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes
|
||||
|
||||
#if ANY(ARC_SUPPORT, BEZIER_CURVE_SUPPORT)
|
||||
//#define CNC_WORKSPACE_PLANES // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes
|
||||
|
|
@ -2819,7 +2812,7 @@
|
|||
* Currently handles M108, M112, M410, M876
|
||||
* NOTE: Not yet implemented for all platforms.
|
||||
*/
|
||||
//#define EMERGENCY_PARSER
|
||||
#define EMERGENCY_PARSER
|
||||
|
||||
/**
|
||||
* Realtime Reporting (requires EMERGENCY_PARSER)
|
||||
|
|
@ -2847,10 +2840,10 @@
|
|||
* Some other clients start sending commands while receiving a 'wait'.
|
||||
* This "wait" is only sent when the buffer is empty. 1 second is a good value here.
|
||||
*/
|
||||
//#define NO_TIMEOUTS 1000 // (ms)
|
||||
#define NO_TIMEOUTS 1000 // (ms)
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
#define ADVANCED_OK
|
||||
|
||||
// Printrun may have trouble receiving long strings all at once.
|
||||
// This option inserts short delays between lines of serial output.
|
||||
|
|
@ -2904,7 +2897,7 @@
|
|||
*
|
||||
* Note that M207 / M208 / M209 settings are saved to EEPROM.
|
||||
*/
|
||||
//#define FWRETRACT
|
||||
#define FWRETRACT
|
||||
#if ENABLED(FWRETRACT)
|
||||
#define FWRETRACT_AUTORETRACT // Override slicer retractions
|
||||
#if ENABLED(FWRETRACT_AUTORETRACT)
|
||||
|
|
@ -3052,14 +3045,14 @@
|
|||
*
|
||||
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 3 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 50 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
|
|
@ -3068,7 +3061,7 @@
|
|||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 25 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
|
|
@ -3078,7 +3071,7 @@
|
|||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
|
||||
//#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
|
||||
#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length.
|
||||
|
|
@ -3086,17 +3079,17 @@
|
|||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
#define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
//#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again.
|
||||
//#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#define CONFIGURE_FILAMENT_CHANGE // Add M603 G-code and menu items. Requires ~1.3K bytes of flash.
|
||||
#endif
|
||||
|
||||
|
|
@ -4331,10 +4324,10 @@
|
|||
* Host Prompt Support enables Marlin to use the host for user prompts so
|
||||
* filament runout and other processes can be managed from the host side.
|
||||
*/
|
||||
//#define HOST_ACTION_COMMANDS
|
||||
#define HOST_ACTION_COMMANDS
|
||||
#if ENABLED(HOST_ACTION_COMMANDS)
|
||||
//#define HOST_PAUSE_M76 // Tell the host to pause in response to M76
|
||||
//#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
|
||||
#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
|
||||
#if ENABLED(HOST_PROMPT_SUPPORT)
|
||||
//#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
|
||||
#endif
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue