From ec08426dad1225b47181c5b7a595f5ed1a71ee7f Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Tue, 7 Oct 2025 00:43:36 -0500 Subject: [PATCH] =?UTF-8?q?=F0=9F=8E=A8=20Fix=20echoes?= MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit --- config/default/Configuration.h | 2 +- config/default/Configuration_adv.h | 8 ++++---- config/examples/3DFabXYZ/Migbot/Configuration.h | 2 +- config/examples/3DFabXYZ/Migbot/Configuration_adv.h | 8 ++++---- config/examples/3DMatik/XL/Configuration.h | 2 +- config/examples/3DMatik/XL/Configuration_adv.h | 8 ++++---- config/examples/ADIMLab/Gantry v1/Configuration.h | 2 +- config/examples/ADIMLab/Gantry v1/Configuration_adv.h | 8 ++++---- config/examples/ADIMLab/Gantry v2/Configuration.h | 2 +- config/examples/ADIMLab/Gantry v2/Configuration_adv.h | 8 ++++---- config/examples/Alfawise/U20-bltouch/Configuration.h | 2 +- config/examples/Alfawise/U20-bltouch/Configuration_adv.h | 8 ++++---- config/examples/Alfawise/U20/Configuration.h | 2 +- config/examples/Alfawise/U20/Configuration_adv.h | 8 ++++---- config/examples/AliExpress/CL-260/Configuration.h | 2 +- config/examples/AliExpress/CL-260/Configuration_adv.h | 8 ++++---- config/examples/AliExpress/UM2pExt/Configuration.h | 2 +- config/examples/AliExpress/UM2pExt/Configuration_adv.h | 8 ++++---- config/examples/Anet/A2/Configuration.h | 2 +- config/examples/Anet/A2/Configuration_adv.h | 8 ++++---- config/examples/Anet/A2plus/Configuration.h | 2 +- config/examples/Anet/A2plus/Configuration_adv.h | 8 ++++---- config/examples/Anet/A6/Configuration.h | 2 +- config/examples/Anet/A6/Configuration_adv.h | 8 ++++---- config/examples/Anet/A8/Configuration.h | 2 +- config/examples/Anet/A8/Configuration_adv.h | 8 ++++---- config/examples/Anet/A8plus/Configuration.h | 2 +- config/examples/Anet/A8plus/Configuration_adv.h | 8 ++++---- config/examples/Anet/A9/Configuration.h | 2 +- config/examples/Anet/A9/Configuration_adv.h | 8 ++++---- config/examples/Anet/E10/Configuration.h | 2 +- config/examples/Anet/E10/Configuration_adv.h | 8 ++++---- config/examples/Anet/E16/BTT SKR 1.3/Configuration.h | 2 +- config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h | 8 ++++---- config/examples/Anet/E16/Stock/Configuration.h | 2 +- config/examples/Anet/E16/Stock/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET4+/Configuration.h | 2 +- config/examples/Anet/ET4+/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET4-Pro/Configuration.h | 2 +- config/examples/Anet/ET4-Pro/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET4/Configuration.h | 2 +- config/examples/Anet/ET4/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET4X/Configuration.h | 2 +- config/examples/Anet/ET4X/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET5-Pro/Configuration.h | 2 +- config/examples/Anet/ET5-Pro/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET5/Configuration.h | 2 +- config/examples/Anet/ET5/Configuration_adv.h | 8 ++++---- config/examples/Anet/ET5X/Configuration.h | 2 +- config/examples/Anet/ET5X/Configuration_adv.h | 8 ++++---- config/examples/AnyCubic/Chiron/Configuration.h | 2 +- config/examples/AnyCubic/Chiron/Configuration_adv.h | 8 ++++---- .../AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h | 2 +- .../Mega Zero 2.0/Anycubic V1/Configuration_adv.h | 8 ++++---- .../AnyCubic/Mega Zero/Anycubic V1/Configuration.h | 2 +- .../AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini MZ V1.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h | 8 ++++---- config/examples/AnyCubic/Vyper/Configuration.h | 2 +- config/examples/AnyCubic/Vyper/Configuration_adv.h | 8 ++++---- .../AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h | 2 +- .../AnyCubic/i3 Mega/Trigorilla AVR/Configuration_adv.h | 8 ++++---- .../AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h | 2 +- .../i3 Mega/Trigorilla Pro STM32/Configuration_adv.h | 8 ++++---- config/examples/AnyCubic/i3/Configuration.h | 2 +- config/examples/AnyCubic/i3/Configuration_adv.h | 8 ++++---- config/examples/ArmEd/Configuration.h | 2 +- config/examples/ArmEd/Configuration_adv.h | 8 ++++---- config/examples/Artillery/Genius Pro/Configuration.h | 2 +- config/examples/Artillery/Genius Pro/Configuration_adv.h | 8 ++++---- config/examples/Artillery/Genius/BLTouch/Configuration.h | 2 +- .../examples/Artillery/Genius/BLTouch/Configuration_adv.h | 8 ++++---- config/examples/Artillery/Genius/V1/Configuration.h | 2 +- config/examples/Artillery/Genius/V1/Configuration_adv.h | 8 ++++---- config/examples/Artillery/Hornet/Configuration.h | 2 +- config/examples/Artillery/Hornet/Configuration_adv.h | 8 ++++---- .../Sidewinder X1/0.9 BMG - E3D V6/Configuration.h | 2 +- .../Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h | 8 ++++---- .../examples/Artillery/Sidewinder X1/V1/Configuration.h | 2 +- .../Artillery/Sidewinder X1/V1/Configuration_adv.h | 8 ++++---- config/examples/Artillery/Sidewinder X2/Configuration.h | 2 +- .../examples/Artillery/Sidewinder X2/Configuration_adv.h | 8 ++++---- config/examples/Azteeg/X5GT/Configuration.h | 2 +- config/examples/Azteeg/X5GT/Configuration_adv.h | 8 ++++---- config/examples/BIBO/TouchX/cyclops/Configuration.h | 2 +- config/examples/BIBO/TouchX/cyclops/Configuration_adv.h | 8 ++++---- .../BIBO/TouchX/default - BLTouch/Configuration.h | 2 +- .../BIBO/TouchX/default - BLTouch/Configuration_adv.h | 8 ++++---- config/examples/BIBO/TouchX/default/Configuration.h | 2 +- config/examples/BIBO/TouchX/default/Configuration_adv.h | 8 ++++---- config/examples/BIQU/B1 SE Plus/Configuration.h | 2 +- config/examples/BIQU/B1 SE Plus/Configuration_adv.h | 8 ++++---- config/examples/BIQU/B1 SE/Configuration.h | 2 +- config/examples/BIQU/B1 SE/Configuration_adv.h | 8 ++++---- config/examples/BIQU/B1/Configuration.h | 2 +- config/examples/BIQU/B1/Configuration_adv.h | 8 ++++---- config/examples/BIQU/BX/Configuration.h | 2 +- config/examples/BIQU/BX/Configuration_adv.h | 8 ++++---- config/examples/BIQU/Hurakan/Configuration.h | 2 +- config/examples/BIQU/Hurakan/Configuration_adv.h | 8 ++++---- config/examples/BIQU/Thunder Standard/Configuration.h | 2 +- config/examples/BIQU/Thunder Standard/Configuration_adv.h | 8 ++++---- config/examples/BQ/Hephestos/Configuration.h | 2 +- config/examples/BQ/Hephestos/Configuration_adv.h | 8 ++++---- config/examples/BQ/Hephestos_2/Configuration.h | 2 +- config/examples/BQ/Hephestos_2/Configuration_adv.h | 8 ++++---- config/examples/BQ/WITBOX/Configuration.h | 2 +- config/examples/BQ/WITBOX/Configuration_adv.h | 8 ++++---- config/examples/CNC/miniRambo/Configuration.h | 2 +- config/examples/CNC/miniRambo/Configuration_adv.h | 8 ++++---- config/examples/CTC/A13/Configuration.h | 2 +- config/examples/CTC/A13/Configuration_adv.h | 8 ++++---- config/examples/CTC/Bizer/Configuration.h | 2 +- config/examples/CTC/Bizer/Configuration_adv.h | 8 ++++---- .../examples/CTC/i3 2560 Rev A/no probe/Configuration.h | 2 +- .../CTC/i3 2560 Rev A/no probe/Configuration_adv.h | 8 ++++---- config/examples/Cartesio/Configuration.h | 2 +- config/examples/Cartesio/Configuration_adv.h | 8 ++++---- config/examples/Copymaster3D/300/Configuration.h | 2 +- config/examples/Copymaster3D/300/Configuration_adv.h | 8 ++++---- config/examples/Copymaster3D/400/Configuration.h | 2 +- config/examples/Copymaster3D/400/Configuration_adv.h | 8 ++++---- config/examples/Copymaster3D/500/Configuration.h | 2 +- config/examples/Copymaster3D/500/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-10 Max/Configuration.h | 2 +- config/examples/Creality/CR-10 Max/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- .../Creality/CR-10 Mini/CrealityV1/Configuration.h | 2 +- .../Creality/CR-10 Mini/CrealityV1/Configuration_adv.h | 8 ++++---- .../examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h | 2 +- .../Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h | 8 ++++---- .../examples/Creality/CR-10 S4/CrealityV1/Configuration.h | 2 +- .../Creality/CR-10 S4/CrealityV1/Configuration_adv.h | 8 ++++---- .../Configuration.h | 2 +- .../Configuration_adv.h | 8 ++++---- .../CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 v3/Configuration_adv.h | 8 ++++---- .../examples/Creality/CR-10 S5/CrealityV1/Configuration.h | 2 +- .../Creality/CR-10 S5/CrealityV1/Configuration_adv.h | 8 ++++---- .../CR-10 S5/CrealityV2.2 - BLTouch/Configuration.h | 2 +- .../CR-10 S5/CrealityV2.2 - BLTouch/Configuration_adv.h | 8 ++++---- .../CR-10 S5/CrealityV427 - BLTouch/Configuration.h | 2 +- .../CR-10 S5/CrealityV427 - BLTouch/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-10 V2/Configuration.h | 2 +- config/examples/Creality/CR-10 V2/Configuration_adv.h | 8 ++++---- .../CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 v3/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-10 V3/Stock/Configuration.h | 2 +- .../examples/Creality/CR-10 V3/Stock/Configuration_adv.h | 8 ++++---- .../CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../CR-10/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-10/CrealityV1/Configuration.h | 2 +- .../Creality/CR-10/CrealityV1/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-10S Pro/Configuration.h | 2 +- config/examples/Creality/CR-10S Pro/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h | 2 +- .../BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h | 8 ++++---- .../CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h | 2 +- .../BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h | 8 ++++---- .../CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- .../CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h | 2 +- .../CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h | 8 ++++---- .../Creality/CR-10S/CrealityV1 - BLTouch/Configuration.h | 2 +- .../CR-10S/CrealityV1 - BLTouch/Configuration_adv.h | 8 ++++---- .../examples/Creality/CR-10S/CrealityV1/Configuration.h | 2 +- .../Creality/CR-10S/CrealityV1/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-20 Pro/Configuration.h | 2 +- config/examples/Creality/CR-20 Pro/Configuration_adv.h | 8 ++++---- .../CR-20/RepRapWorld Minitronics20/Configuration.h | 2 +- .../CR-20/RepRapWorld Minitronics20/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-20/Stock/Configuration.h | 2 +- config/examples/Creality/CR-20/Stock/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-30 PrintMill/Configuration.h | 2 +- .../examples/Creality/CR-30 PrintMill/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-6 SE/Configuration.h | 2 +- config/examples/Creality/CR-6 SE/Configuration_adv.h | 8 ++++---- config/examples/Creality/CR-8/Configuration.h | 2 +- config/examples/Creality/CR-8/Configuration_adv.h | 8 ++++---- .../Creality/Ender-2 Pro/CrealityV24S4/Configuration.h | 2 +- .../Ender-2 Pro/CrealityV24S4/Configuration_adv.h | 8 ++++---- .../Creality/Ender-2 Pro/CrealityV423/Configuration.h | 2 +- .../Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-2/Configuration.h | 2 +- config/examples/Creality/Ender-2/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-3 Max Neo/Configuration.h | 2 +- .../examples/Creality/Ender-3 Max Neo/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-3 Max/Configuration.h | 2 +- config/examples/Creality/Ender-3 Max/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-3 Neo/Configuration.h | 2 +- config/examples/Creality/Ender-3 Neo/Configuration_adv.h | 8 ++++---- .../Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h | 2 +- .../BigTreeTech SKR 1.4 Turbo/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 1.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 1.0/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 1.2/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 1.2/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- .../Ender-3 Pro/Creality free-runs/Configuration.h | 2 +- .../Ender-3 Pro/Creality free-runs/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3 Pro/CrealityV1/Configuration.h | 2 +- .../Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3 Pro/CrealityV422/Configuration.h | 2 +- .../Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h | 8 ++++---- .../Ender-3 Pro/CrealityV427 - BLTouch/Configuration.h | 2 +- .../CrealityV427 - BLTouch/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3 Pro/CrealityV427/Configuration.h | 2 +- .../Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-3 S1 Plus/Configuration.h | 2 +- .../examples/Creality/Ender-3 S1 Plus/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-3 S1 Pro/Configuration.h | 2 +- .../examples/Creality/Ender-3 S1 Pro/Configuration_adv.h | 8 ++++---- .../examples/Creality/Ender-3 S1/STM32F1/Configuration.h | 2 +- .../Creality/Ender-3 S1/STM32F1/Configuration_adv.h | 8 ++++---- .../examples/Creality/Ender-3 S1/STM32F4/Configuration.h | 2 +- .../Creality/Ender-3 S1/STM32F4/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3 V2 Neo/CrealityV422/Configuration.h | 2 +- .../Ender-3 V2 Neo/CrealityV422/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h | 2 +- .../CrealityUI/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h | 2 +- .../BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h | 8 ++++---- .../CrealityUI/Configuration.h | 2 +- .../CrealityUI/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration.h | 2 +- .../MarlinUI/Configuration_adv.h | 8 ++++---- .../CrealityUI/Configuration.h | 2 +- .../CrealityUI/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration.h | 2 +- .../MarlinUI/Configuration_adv.h | 8 ++++---- .../Ender-3 V2/CrealityV422/CrealityUI/Configuration.h | 2 +- .../CrealityV422/CrealityUI/Configuration_adv.h | 8 ++++---- .../Ender-3 V2/CrealityV422/MarlinUI/Configuration.h | 2 +- .../Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h | 8 ++++---- .../Ender-3 V2/CrealityV427/CrealityUI/Configuration.h | 2 +- .../CrealityV427/CrealityUI/Configuration_adv.h | 8 ++++---- .../Ender-3 V2/CrealityV427/MarlinUI/Configuration.h | 2 +- .../Ender-3 V2/CrealityV427/MarlinUI/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h | 2 +- .../Ender-3/BigTreeTech E3 RRF/Configuration_adv.h | 8 ++++---- .../Ender-3/BigTreeTech Manta E3 EZ/Configuration.h | 2 +- .../Ender-3/BigTreeTech Manta E3 EZ/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h | 2 +- .../Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h | 8 ++++---- .../2-into-1 Hotend/Configuration.h | 2 +- .../2-into-1 Hotend/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h | 2 +- .../BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h | 8 ++++---- .../Single Extruder/Configuration.h | 2 +- .../Single Extruder/Configuration_adv.h | 8 ++++---- .../Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h | 2 +- .../BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h | 8 ++++---- .../Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 1.0/Configuration_adv.h | 8 ++++---- .../Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 1.2/Configuration_adv.h | 8 ++++---- .../Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/Creality free-runs/Configuration.h | 2 +- .../Ender-3/Creality free-runs/Configuration_adv.h | 8 ++++---- .../examples/Creality/Ender-3/CrealityV1/Configuration.h | 2 +- .../Creality/Ender-3/CrealityV1/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/CrealityV422/Configuration.h | 2 +- .../Creality/Ender-3/CrealityV422/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/CrealityV427/Configuration.h | 2 +- .../Creality/Ender-3/CrealityV427/Configuration_adv.h | 8 ++++---- .../Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h | 2 +- .../FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h | 8 ++++---- .../Ender-3/FYSETC Cheetah 1.2/base/Configuration.h | 2 +- .../Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h | 2 +- .../Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h | 8 ++++---- .../Ender-3/FYSETC Cheetah/BLTouch/Configuration.h | 2 +- .../Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/FYSETC Cheetah/base/Configuration.h | 2 +- .../Ender-3/FYSETC Cheetah/base/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h | 2 +- .../Creality/Ender-3/MEEB-3DP/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h | 2 +- .../Ender-3/MKS Robin E3/V1.0/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h | 2 +- .../Ender-3/MKS Robin E3/V1.1/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/MKS Robin E3P/Configuration.h | 2 +- .../Creality/Ender-3/MKS Robin E3P/Configuration_adv.h | 8 ++++---- .../Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h | 2 +- .../Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-4/Configuration.h | 2 +- config/examples/Creality/Ender-4/Configuration_adv.h | 8 ++++---- .../Ender-5 Plus/BigTreeTech SKR 3/Configuration.h | 2 +- .../Ender-5 Plus/BigTreeTech SKR 3/Configuration_adv.h | 8 ++++---- .../Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration.h | 2 +- .../CrealityV1 (ORIGIN UI)/Configuration_adv.h | 8 ++++---- .../Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration.h | 2 +- .../CrealityV1 (RELOADED UI)/Configuration_adv.h | 8 ++++---- .../Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h | 2 +- .../BigTreeTech SKR E3 Turbo/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR Mini E3 1.2/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 1.2/Configuration_adv.h | 8 ++++---- .../Configuration.h | 2 +- .../Configuration_adv.h | 8 ++++---- .../Configuration.h | 2 +- .../Configuration_adv.h | 8 ++++---- .../Creality/Ender-5 Pro/CrealityV1/Configuration.h | 2 +- .../Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h | 8 ++++---- .../Creality/Ender-5 Pro/CrealityV422/Configuration.h | 2 +- .../Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h | 8 ++++---- .../Creality/Ender-5 Pro/CrealityV427/Configuration.h | 2 +- .../Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-5 S1/Configuration.h | 2 +- config/examples/Creality/Ender-5 S1/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h | 2 +- .../Configuration_adv.h | 8 ++++---- .../Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h | 2 +- .../Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h | 8 ++++---- .../Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 1.2/Configuration_adv.h | 8 ++++---- .../Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../Configuration.h | 2 +- .../Configuration_adv.h | 8 ++++---- .../Creality/Ender-5/Creality free-runs/Configuration.h | 2 +- .../Ender-5/Creality free-runs/Configuration_adv.h | 8 ++++---- .../examples/Creality/Ender-5/CrealityV1/Configuration.h | 2 +- .../Creality/Ender-5/CrealityV1/Configuration_adv.h | 8 ++++---- .../Ender-5/CrealityV427 with BLTouch/Configuration.h | 2 +- .../Ender-5/CrealityV427 with BLTouch/Configuration_adv.h | 8 ++++---- .../Creality/Ender-5/CrealityV427/Configuration.h | 2 +- .../Creality/Ender-5/CrealityV427/Configuration_adv.h | 8 ++++---- config/examples/Creality/Ender-6/Configuration.h | 2 +- config/examples/Creality/Ender-6/Configuration_adv.h | 8 ++++---- config/examples/Dagoma/Disco Ultimate/Configuration.h | 2 +- config/examples/Dagoma/Disco Ultimate/Configuration_adv.h | 8 ++++---- config/examples/Daycom/3DP-100/Configuration.h | 2 +- config/examples/Daycom/3DP-100/Configuration_adv.h | 8 ++++---- config/examples/E3D/BigBox Dual/Configuration.h | 2 +- config/examples/E3D/BigBox Dual/Configuration_adv.h | 8 ++++---- .../EXP3D/Imprimante multifonction/Configuration.h | 2 +- .../EXP3D/Imprimante multifonction/Configuration_adv.h | 8 ++++---- config/examples/EasyThreeD/ET4000PLUS/Configuration.h | 2 +- config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h | 8 ++++---- config/examples/Eazao/Zero/Configuration.h | 2 +- config/examples/Eazao/Zero/Configuration_adv.h | 8 ++++---- config/examples/Einstart-S/Configuration.h | 2 +- config/examples/Einstart-S/Configuration_adv.h | 8 ++++---- config/examples/Elegoo/Neptune 2/Configuration.h | 2 +- config/examples/Elegoo/Neptune 2/Configuration_adv.h | 8 ++++---- config/examples/Eryone/Thinker SE/Configuration.h | 2 +- config/examples/Eryone/Thinker SE/Configuration_adv.h | 8 ++++---- config/examples/Eryone/Thinker V2/Configuration.h | 2 +- config/examples/Eryone/Thinker V2/Configuration_adv.h | 8 ++++---- config/examples/FYSETC/AIO_II/Configuration.h | 2 +- config/examples/FYSETC/AIO_II/Configuration_adv.h | 8 ++++---- config/examples/FYSETC/F6_13/Configuration.h | 2 +- config/examples/FYSETC/F6_13/Configuration_adv.h | 8 ++++---- config/examples/FYSETC/S6/Configuration.h | 2 +- config/examples/FYSETC/S6/Configuration_adv.h | 8 ++++---- config/examples/Felix/DUAL/Configuration.h | 2 +- config/examples/Felix/DUAL/Configuration_adv.h | 8 ++++---- config/examples/Felix/Single/Configuration.h | 2 +- config/examples/Felix/Single/Configuration_adv.h | 8 ++++---- config/examples/FlashForge/Creator 2X/Configuration.h | 2 +- config/examples/FlashForge/Creator 2X/Configuration_adv.h | 8 ++++---- config/examples/FlashForge/CreatorPro/Configuration.h | 2 +- config/examples/FlashForge/CreatorPro/Configuration_adv.h | 8 ++++---- .../FlyingBear/FlyingBearGhost_v3/Configuration.h | 2 +- .../FlyingBear/FlyingBearGhost_v3/Configuration_adv.h | 8 ++++---- config/examples/FlyingBear/P902/Configuration.h | 2 +- config/examples/FlyingBear/P902/Configuration_adv.h | 8 ++++---- config/examples/FlyingBear/P905H/Configuration.h | 2 +- config/examples/FlyingBear/P905H/Configuration_adv.h | 8 ++++---- config/examples/FoamCutter/generic/Configuration.h | 2 +- config/examples/FoamCutter/generic/Configuration_adv.h | 8 ++++---- config/examples/FoamCutter/rcKeith/Configuration.h | 2 +- config/examples/FoamCutter/rcKeith/Configuration_adv.h | 8 ++++---- config/examples/FolgerTech/FT-5 R2/Configuration.h | 2 +- config/examples/FolgerTech/FT-5 R2/Configuration_adv.h | 8 ++++---- config/examples/FolgerTech/i3-2020/Configuration.h | 2 +- config/examples/FolgerTech/i3-2020/Configuration_adv.h | 8 ++++---- config/examples/Formbot/Raptor/Configuration.h | 2 +- config/examples/Formbot/Raptor/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A10/Configuration.h | 2 +- config/examples/Geeetech/A10/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A10D/Configuration.h | 2 +- config/examples/Geeetech/A10D/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A10M/Stock LCD/Configuration.h | 2 +- .../examples/Geeetech/A10M/Stock LCD/Configuration_adv.h | 8 ++++---- .../examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h | 2 +- .../Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A10PRO/Configuration.h | 2 +- config/examples/Geeetech/A10PRO/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A10T/Stock LCD/Configuration.h | 2 +- .../examples/Geeetech/A10T/Stock LCD/Configuration_adv.h | 8 ++++---- .../examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h | 2 +- .../Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A20/Configuration.h | 2 +- config/examples/Geeetech/A20/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A20M/Configuration.h | 2 +- config/examples/Geeetech/A20M/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A20T/Configuration.h | 2 +- config/examples/Geeetech/A20T/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A30/Configuration.h | 2 +- config/examples/Geeetech/A30/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A30M/Configuration.h | 2 +- config/examples/Geeetech/A30M/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/A30T/Configuration.h | 2 +- config/examples/Geeetech/A30T/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/D200/Configuration.h | 2 +- config/examples/Geeetech/D200/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/Duplicator5/Configuration.h | 2 +- config/examples/Geeetech/Duplicator5/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/E180/Configuration.h | 2 +- config/examples/Geeetech/E180/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/GT2560/Configuration.h | 2 +- config/examples/Geeetech/GT2560/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h | 2 +- .../examples/Geeetech/I3_Pro_X-GT2560/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/M201/Configuration.h | 2 +- config/examples/Geeetech/M201/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/MeCreator2/Configuration.h | 2 +- config/examples/Geeetech/MeCreator2/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/Me_creator/Configuration.h | 2 +- config/examples/Geeetech/Me_creator/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/Me_ducer/Configuration.h | 2 +- config/examples/Geeetech/Me_ducer/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/PI3A PRO/Configuration.h | 2 +- config/examples/Geeetech/PI3A PRO/Configuration_adv.h | 8 ++++---- .../Geeetech/Prusa i3 Pro B/bltouch/Configuration.h | 2 +- .../Geeetech/Prusa i3 Pro B/bltouch/Configuration_adv.h | 8 ++++---- .../Geeetech/Prusa i3 Pro B/noprobe/Configuration.h | 2 +- .../Geeetech/Prusa i3 Pro B/noprobe/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/Prusa i3 Pro C/Configuration.h | 2 +- .../examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h | 8 ++++---- config/examples/Geeetech/Prusa i3 Pro W/Configuration.h | 2 +- .../examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h | 8 ++++---- config/examples/HMS434/Configuration.h | 2 +- config/examples/HMS434/Configuration_adv.h | 8 ++++---- config/examples/Hictop/3DP-17/Configuration.h | 2 +- config/examples/Hictop/3DP-17/Configuration_adv.h | 8 ++++---- config/examples/Infitary/i3-M508/Configuration.h | 2 +- config/examples/Infitary/i3-M508/Configuration_adv.h | 8 ++++---- config/examples/Intamsys/FunmatHT 4988/Configuration.h | 2 +- .../examples/Intamsys/FunmatHT 4988/Configuration_adv.h | 8 ++++---- config/examples/JGAurora/A1/Configuration.h | 2 +- config/examples/JGAurora/A1/Configuration_adv.h | 8 ++++---- config/examples/JGAurora/A3/Configuration.h | 2 +- config/examples/JGAurora/A3/Configuration_adv.h | 8 ++++---- config/examples/JGAurora/A5/Configuration.h | 2 +- config/examples/JGAurora/A5/Configuration_adv.h | 8 ++++---- config/examples/JGAurora/A5S/Configuration.h | 2 +- config/examples/JGAurora/A5S/Configuration_adv.h | 8 ++++---- config/examples/JGAurora/Magic/Configuration.h | 2 +- config/examples/JGAurora/Magic/Configuration_adv.h | 8 ++++---- config/examples/Kingroon/KP3/Configuration.h | 2 +- config/examples/Kingroon/KP3/Configuration_adv.h | 8 ++++---- config/examples/Kingroon/KP3S/Configuration.h | 2 +- config/examples/Kingroon/KP3S/Configuration_adv.h | 8 ++++---- config/examples/Kingroon/KP3S_Pro/Configuration.h | 2 +- config/examples/Kingroon/KP3S_Pro/Configuration_adv.h | 8 ++++---- config/examples/Kingroon/KP5L-DIY/Configuration.h | 2 +- config/examples/Kingroon/KP5L-DIY/Configuration_adv.h | 8 ++++---- config/examples/Labists/ET4/Configuration.h | 2 +- config/examples/Labists/ET4/Configuration_adv.h | 8 ++++---- config/examples/Longer/LK5/Configuration.h | 2 +- config/examples/Longer/LK5/Configuration_adv.h | 8 ++++---- config/examples/LulzBot/TAZ4/Configuration.h | 2 +- config/examples/LulzBot/TAZ4/Configuration_adv.h | 8 ++++---- config/examples/MBot/Cube/Configuration.h | 2 +- config/examples/MBot/Cube/Configuration_adv.h | 8 ++++---- config/examples/MakerBot/Replicator Dual/Configuration.h | 2 +- .../examples/MakerBot/Replicator Dual/Configuration_adv.h | 8 ++++---- .../examples/MakerBot/Replicator Single/Configuration.h | 2 +- .../MakerBot/Replicator Single/Configuration_adv.h | 8 ++++---- config/examples/MakerFarm/Pegasus 12/Configuration.h | 2 +- config/examples/MakerFarm/Pegasus 12/Configuration_adv.h | 8 ++++---- config/examples/MakerGear/M2 Rev H/Configuration.h | 2 +- config/examples/MakerGear/M2 Rev H/Configuration_adv.h | 8 ++++---- config/examples/MakerParts/Configuration.h | 2 +- config/examples/MakerParts/Configuration_adv.h | 8 ++++---- .../examples/MakerTech3D/Proforge2sDual/Configuration.h | 2 +- .../MakerTech3D/Proforge2sDual/Configuration_adv.h | 8 ++++---- config/examples/Malyan/M150/Configuration.h | 2 +- config/examples/Malyan/M150/Configuration_adv.h | 8 ++++---- config/examples/Malyan/M180/Configuration.h | 2 +- config/examples/Malyan/M180/Configuration_adv.h | 8 ++++---- config/examples/Malyan/M200/Configuration.h | 2 +- config/examples/Malyan/M200/Configuration_adv.h | 8 ++++---- config/examples/Materia101/Configuration.h | 2 +- config/examples/Materia101/Configuration_adv.h | 8 ++++---- config/examples/Micromake/C1/basic/Configuration.h | 2 +- config/examples/Micromake/C1/basic/Configuration_adv.h | 8 ++++---- config/examples/Micromake/C1/enhanced/Configuration.h | 2 +- config/examples/Micromake/C1/enhanced/Configuration_adv.h | 8 ++++---- config/examples/Mks/Robin/Configuration.h | 2 +- config/examples/Mks/Robin/Configuration_adv.h | 8 ++++---- config/examples/Mks/Robin_Lite3/Configuration.h | 2 +- config/examples/Mks/Robin_Lite3/Configuration_adv.h | 8 ++++---- config/examples/Mks/Robin_Pro/Configuration.h | 2 +- config/examples/Mks/Robin_Pro/Configuration_adv.h | 8 ++++---- config/examples/Mks/Sbase/Configuration.h | 2 +- config/examples/Mks/Sbase/Configuration_adv.h | 8 ++++---- config/examples/Modix/Big60/Configuration.h | 2 +- config/examples/Modix/Big60/Configuration_adv.h | 8 ++++---- config/examples/Nextion/Configuration.h | 2 +- config/examples/Nextion/Configuration_adv.h | 8 ++++---- .../examples/ORD Bot/Hadron/Sanguinololu/Configuration.h | 2 +- .../ORD Bot/Hadron/Sanguinololu/Configuration_adv.h | 8 ++++---- config/examples/Opulo/Lumen_REV3/Configuration.h | 2 +- config/examples/Opulo/Lumen_REV3/Configuration_adv.h | 8 ++++---- config/examples/Opulo/Lumen_REV4/Configuration.h | 2 +- config/examples/Opulo/Lumen_REV4/Configuration_adv.h | 8 ++++---- config/examples/Opulo/Lumen_REV5/Configuration.h | 2 +- config/examples/Opulo/Lumen_REV5/Configuration_adv.h | 8 ++++---- config/examples/Ortur 4/Configuration.h | 2 +- config/examples/Ortur 4/Configuration_adv.h | 8 ++++---- config/examples/Polargraph/Configuration.h | 2 +- config/examples/Polargraph/Configuration_adv.h | 8 ++++---- config/examples/Printrbot/PrintrboardG2/Configuration.h | 2 +- .../examples/Printrbot/PrintrboardG2/Configuration_adv.h | 8 ++++---- .../examples/Printrbot/Simple Metal RevD/Configuration.h | 2 +- .../Printrbot/Simple Metal RevD/Configuration_adv.h | 8 ++++---- .../examples/Printrbot/Simple_Metal_RevF6/Configuration.h | 2 +- .../Printrbot/Simple_Metal_RevF6/Configuration_adv.h | 8 ++++---- config/examples/Prusa/MK3/Configuration.h | 2 +- config/examples/Prusa/MK3/Configuration_adv.h | 8 ++++---- .../Prusa/MK3S-BigTreeTech-BTT002/Configuration.h | 2 +- .../Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h | 8 ++++---- config/examples/Qidi/Qidi 1/Configuration.h | 2 +- config/examples/Qidi/Qidi 1/Configuration_adv.h | 8 ++++---- config/examples/Raiscube/A8r/Configuration.h | 2 +- config/examples/Raiscube/A8r/Configuration_adv.h | 8 ++++---- config/examples/RapideLite/RL200/Configuration.h | 2 +- config/examples/RapideLite/RL200/Configuration_adv.h | 8 ++++---- config/examples/Renkforce/RF100/Configuration.h | 2 +- config/examples/Renkforce/RF100/Configuration_adv.h | 8 ++++---- config/examples/Renkforce/RF100XL/Configuration.h | 2 +- config/examples/Renkforce/RF100XL/Configuration_adv.h | 8 ++++---- config/examples/Renkforce/RF100v2/Configuration.h | 2 +- config/examples/Renkforce/RF100v2/Configuration_adv.h | 8 ++++---- config/examples/RepRapPro/Huxley/Configuration.h | 2 +- config/examples/RepRapPro/Huxley/Configuration_adv.h | 8 ++++---- config/examples/RepRapWorld/Megatronics/Configuration.h | 2 +- .../examples/RepRapWorld/Megatronics/Configuration_adv.h | 8 ++++---- config/examples/RepRapWorld/Minitronics11/Configuration.h | 2 +- .../RepRapWorld/Minitronics11/Configuration_adv.h | 8 ++++---- .../RepRapWorld/Minitronics20/CNC/Configuration.h | 2 +- .../RepRapWorld/Minitronics20/CNC/Configuration_adv.h | 8 ++++---- config/examples/RigidBot/Configuration.h | 2 +- config/examples/RigidBot/Configuration_adv.h | 8 ++++---- config/examples/Robo3D/R1+/Configuration.h | 2 +- config/examples/Robo3D/R1+/Configuration_adv.h | 8 ++++---- config/examples/Rolohaun/Rook MK1/Configuration.h | 2 +- config/examples/Rolohaun/Rook MK1/Configuration_adv.h | 8 ++++---- config/examples/SCARA/MP_SCARA/Configuration.h | 2 +- config/examples/SCARA/MP_SCARA/Configuration_adv.h | 8 ++++---- config/examples/SCARA/Morgan/Configuration.h | 2 +- config/examples/SCARA/Morgan/Configuration_adv.h | 8 ++++---- config/examples/STM32/Black_STM32F407VET6/Configuration.h | 2 +- .../STM32/Black_STM32F407VET6/Configuration_adv.h | 8 ++++---- config/examples/STM32/STM32F103RE/Configuration.h | 2 +- config/examples/STM32/STM32F103RE/Configuration_adv.h | 8 ++++---- config/examples/Simax/Mi-M200/Configuration.h | 2 +- config/examples/Simax/Mi-M200/Configuration_adv.h | 8 ++++---- config/examples/Simulator/Configuration.h | 2 +- config/examples/Simulator/Configuration_adv.h | 8 ++++---- .../Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h | 2 +- .../SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h | 8 ++++---- .../SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- .../SV-01/BigTreeTech SKR Mini E3 3.0/Configuration.h | 2 +- .../SV-01/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-01/CrealityV22/Configuration.h | 2 +- .../examples/Sovol/SV-01/CrealityV22/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-01/CrealityV221/Configuration.h | 2 +- .../examples/Sovol/SV-01/CrealityV221/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-02/Configuration.h | 2 +- config/examples/Sovol/SV-02/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-03/Configuration.h | 2 +- config/examples/Sovol/SV-03/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-05/Configuration.h | 2 +- config/examples/Sovol/SV-05/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-06 Plus/Configuration.h | 2 +- config/examples/Sovol/SV-06 Plus/Configuration_adv.h | 8 ++++---- config/examples/Sovol/SV-06/Configuration.h | 2 +- config/examples/Sovol/SV-06/Configuration_adv.h | 8 ++++---- config/examples/Sunlu/S8/Configuration.h | 2 +- config/examples/Sunlu/S8/Configuration_adv.h | 8 ++++---- config/examples/Sunlu/T3/Configuration.h | 2 +- config/examples/Sunlu/T3/Configuration_adv.h | 8 ++++---- config/examples/TPARA/AXEL_TPARA/Configuration.h | 2 +- config/examples/TPARA/AXEL_TPARA/Configuration_adv.h | 8 ++++---- config/examples/Tevo/Michelangelo/Configuration.h | 2 +- config/examples/Tevo/Michelangelo/Configuration_adv.h | 8 ++++---- config/examples/Tevo/Nereus/Configuration.h | 2 +- config/examples/Tevo/Nereus/Configuration_adv.h | 8 ++++---- .../examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration.h | 2 +- .../Tevo/Tarantula Pro/MKS Gen_L/Configuration_adv.h | 8 ++++---- .../Tevo/Tarantula Pro/MKS SGen_L/Configuration.h | 2 +- .../Tevo/Tarantula Pro/MKS SGen_L/Configuration_adv.h | 8 ++++---- .../examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h | 2 +- .../Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h | 8 ++++---- .../examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration.h | 2 +- .../Tevo/Tornado/V2 (MKS Gen_L)/Configuration_adv.h | 8 ++++---- .../Tinkerine/Ditto Pro/RAMPS 1.4/Configuration.h | 2 +- .../Tinkerine/Ditto Pro/RAMPS 1.4/Configuration_adv.h | 8 ++++---- config/examples/TinyBoy2/Configuration.h | 2 +- config/examples/TinyBoy2/Configuration_adv.h | 8 ++++---- .../Tronxy/D01/CXY-v6-191017 board/Configuration.h | 2 +- .../Tronxy/D01/CXY-v6-191017 board/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/X1/Configuration.h | 2 +- config/examples/Tronxy/X1/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/X3A/Configuration.h | 2 +- config/examples/Tronxy/X3A/Configuration_adv.h | 8 ++++---- .../Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration.h | 2 +- .../X5S-2E/Green Board (Chitu V5)/Configuration_adv.h | 8 ++++---- .../X5S-2E/Red Board (Tronxy 3.1.0)/Configuration.h | 2 +- .../X5S-2E/Red Board (Tronxy 3.1.0)/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/X5S/Configuration.h | 2 +- config/examples/Tronxy/X5S/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/X5SA-2E/Configuration.h | 2 +- config/examples/Tronxy/X5SA-2E/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/X5SA/Configuration.h | 2 +- config/examples/Tronxy/X5SA/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/XY100/Configuration.h | 2 +- config/examples/Tronxy/XY100/Configuration_adv.h | 8 ++++---- config/examples/Tronxy/XY2-Pro/Configuration.h | 2 +- config/examples/Tronxy/XY2-Pro/Configuration_adv.h | 8 ++++---- config/examples/Turnigy/Fabrikator/Configuration.h | 2 +- config/examples/Turnigy/Fabrikator/Configuration_adv.h | 8 ++++---- config/examples/Two Trees/BlueR Plus/Configuration.h | 2 +- config/examples/Two Trees/BlueR Plus/Configuration_adv.h | 8 ++++---- config/examples/Two Trees/BlueR/BlueR V1/Configuration.h | 2 +- .../examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h | 8 ++++---- config/examples/Two Trees/BlueR/BlueR V2/Configuration.h | 2 +- .../examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h | 8 ++++---- config/examples/Two Trees/BlueR/BlueR V3/Configuration.h | 2 +- .../examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h | 8 ++++---- config/examples/Two Trees/SP-5_V3/Configuration.h | 2 +- config/examples/Two Trees/SP-5_V3/Configuration_adv.h | 8 ++++---- .../Sapphire Plus/Sapphire Plus V2.1/Configuration.h | 2 +- .../Sapphire Plus/Sapphire Plus V2.1/Configuration_adv.h | 8 ++++---- .../Sapphire Plus/Sapphire Plus V2/Configuration.h | 2 +- .../Sapphire Plus/Sapphire Plus V2/Configuration_adv.h | 8 ++++---- config/examples/Two Trees/Sapphire Pro/Configuration.h | 2 +- .../examples/Two Trees/Sapphire Pro/Configuration_adv.h | 8 ++++---- config/examples/UltiMachine/Archim1/Configuration.h | 2 +- config/examples/UltiMachine/Archim1/Configuration_adv.h | 8 ++++---- config/examples/UltiMachine/Archim2/Configuration.h | 2 +- config/examples/UltiMachine/Archim2/Configuration_adv.h | 8 ++++---- config/examples/Ultimaker/Ultimaker 2+/Configuration.h | 2 +- .../examples/Ultimaker/Ultimaker 2+/Configuration_adv.h | 8 ++++---- config/examples/Ultimaker/Ultimaker 2/Configuration.h | 2 +- config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h | 8 ++++---- .../Ultimaker/Ultimaker Original (1.5.7)/Configuration.h | 2 +- .../Ultimaker Original (1.5.7)/Configuration_adv.h | 8 ++++---- .../Ultimaker Original Plus (2.1.1)/Configuration.h | 2 +- .../Ultimaker Original Plus (2.1.1)/Configuration_adv.h | 8 ++++---- .../Ultimaker/Ultimaker Original Plus DXU/Configuration.h | 2 +- .../Ultimaker Original Plus DXU/Configuration_adv.h | 8 ++++---- config/examples/VORONDesign/Configuration.h | 2 +- config/examples/VORONDesign/Configuration_adv.h | 8 ++++---- config/examples/Velleman/K8200 Upgraded/Configuration.h | 2 +- .../examples/Velleman/K8200 Upgraded/Configuration_adv.h | 8 ++++---- config/examples/Velleman/K8200/Configuration.h | 2 +- config/examples/Velleman/K8200/Configuration_adv.h | 8 ++++---- config/examples/Velleman/K8400/Dual-head/Configuration.h | 2 +- .../examples/Velleman/K8400/Dual-head/Configuration_adv.h | 8 ++++---- .../examples/Velleman/K8400/Single-head/Configuration.h | 2 +- .../Velleman/K8400/Single-head/Configuration_adv.h | 8 ++++---- .../Aquila/BigTreeTech SKR Mini E3 2.0/Configuration.h | 2 +- .../BigTreeTech SKR Mini E3 2.0/Configuration_adv.h | 8 ++++---- config/examples/WASP/PowerWASP/Configuration.h | 2 +- config/examples/WASP/PowerWASP/Configuration_adv.h | 8 ++++---- config/examples/Wanhao/Duplicator 4S/Configuration.h | 2 +- config/examples/Wanhao/Duplicator 4S/Configuration_adv.h | 8 ++++---- config/examples/Wanhao/Duplicator 6/Configuration.h | 2 +- config/examples/Wanhao/Duplicator 6/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK1/300/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK1/300/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK1/400/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK1/400/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK1/500/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK1/500/Configuration_adv.h | 8 ++++---- .../Wanhao/Duplicator 9/MK1u2/300/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK1u2/300/Configuration_adv.h | 8 ++++---- .../Wanhao/Duplicator 9/MK1u2/400/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK1u2/400/Configuration_adv.h | 8 ++++---- .../Wanhao/Duplicator 9/MK1u2/500/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK1u2/500/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK2/300/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK2/300/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK2/400/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK2/400/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK2/500/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK2/500/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK3/300/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK3/300/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK3/400/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK3/400/Configuration_adv.h | 8 ++++---- .../examples/Wanhao/Duplicator 9/MK3/500/Configuration.h | 2 +- .../Wanhao/Duplicator 9/MK3/500/Configuration_adv.h | 8 ++++---- config/examples/Wanhao/Duplicator i3 2.1/Configuration.h | 2 +- .../examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h | 8 ++++---- config/examples/Wanhao/Duplicator i3 Mini/Configuration.h | 2 +- .../Wanhao/Duplicator i3 Mini/Configuration_adv.h | 8 ++++---- config/examples/Wanhao/Duplicator i3 Plus/Configuration.h | 2 +- .../Wanhao/Duplicator i3 Plus/Configuration_adv.h | 8 ++++---- config/examples/Weedo/Tina2/V2/Configuration.h | 2 +- config/examples/Weedo/Tina2/V2/Configuration_adv.h | 8 ++++---- config/examples/Weedo/Tina2/V3/Configuration.h | 2 +- config/examples/Weedo/Tina2/V3/Configuration_adv.h | 8 ++++---- config/examples/Weistek/wt150/Configuration.h | 2 +- config/examples/Weistek/wt150/Configuration_adv.h | 8 ++++---- config/examples/Zonestar/P802M/Configuration.h | 2 +- config/examples/Zonestar/P802M/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h | 2 +- .../BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h | 8 ++++---- .../BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h | 2 +- .../Configuration_adv.h | 8 ++++---- .../delta/Anycubic/Kossel Linear Plus/Configuration.h | 2 +- .../delta/Anycubic/Kossel Linear Plus/Configuration_adv.h | 8 ++++---- config/examples/delta/Anycubic/Kossel/Configuration.h | 2 +- config/examples/delta/Anycubic/Kossel/Configuration_adv.h | 8 ++++---- config/examples/delta/Anycubic/Predator/Configuration.h | 2 +- .../examples/delta/Anycubic/Predator/Configuration_adv.h | 8 ++++---- config/examples/delta/Dreammaker/Overlord/Configuration.h | 2 +- .../delta/Dreammaker/Overlord/Configuration_adv.h | 8 ++++---- .../delta/Dreammaker/Overlord_Pro/Configuration.h | 2 +- .../delta/Dreammaker/Overlord_Pro/Configuration_adv.h | 8 ++++---- config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h | 2 +- .../examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h | 8 ++++---- config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h | 2 +- .../examples/delta/FLSUN/Q5-nano_v2/Configuration_adv.h | 8 ++++---- config/examples/delta/FLSUN/QQ-S/Configuration.h | 2 +- config/examples/delta/FLSUN/QQ-S/Configuration_adv.h | 8 ++++---- config/examples/delta/FLSUN/QQS-Pro/Configuration.h | 2 +- config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h | 8 ++++---- .../examples/delta/FLSUN/auto_calibrate/Configuration.h | 2 +- .../delta/FLSUN/auto_calibrate/Configuration_adv.h | 8 ++++---- config/examples/delta/FLSUN/kossel/Configuration.h | 2 +- config/examples/delta/FLSUN/kossel/Configuration_adv.h | 8 ++++---- config/examples/delta/FLSUN/kossel_mini/Configuration.h | 2 +- .../examples/delta/FLSUN/kossel_mini/Configuration_adv.h | 8 ++++---- config/examples/delta/Geeetech/G2/Configuration.h | 2 +- config/examples/delta/Geeetech/G2/Configuration_adv.h | 8 ++++---- config/examples/delta/Geeetech/G2Pro/Configuration.h | 2 +- config/examples/delta/Geeetech/G2Pro/Configuration_adv.h | 8 ++++---- config/examples/delta/Geeetech/G2S/Configuration.h | 2 +- config/examples/delta/Geeetech/G2S/Configuration_adv.h | 8 ++++---- config/examples/delta/Geeetech/G2SPro/Configuration.h | 2 +- config/examples/delta/Geeetech/G2SPro/Configuration_adv.h | 8 ++++---- .../examples/delta/Geeetech/Rostock 301/Configuration.h | 2 +- .../delta/Geeetech/Rostock 301/Configuration_adv.h | 8 ++++---- config/examples/delta/Hatchbox_Alpha/Configuration.h | 2 +- config/examples/delta/Hatchbox_Alpha/Configuration_adv.h | 8 ++++---- config/examples/delta/MKS/SBASE/Configuration.h | 2 +- config/examples/delta/MKS/SBASE/Configuration_adv.h | 8 ++++---- config/examples/delta/Malyan M300/Configuration.h | 2 +- config/examples/delta/Malyan M300/Configuration_adv.h | 8 ++++---- .../delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration.h | 2 +- .../delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration_adv.h | 8 ++++---- .../examples/delta/Micromake-D1/RAMPS-1.4/Configuration.h | 2 +- .../delta/Micromake-D1/RAMPS-1.4/Configuration_adv.h | 8 ++++---- config/examples/delta/Tevo Little Monster/Configuration.h | 2 +- .../delta/Tevo Little Monster/Configuration_adv.h | 8 ++++---- config/examples/delta/Velleman/K8800/Configuration.h | 2 +- config/examples/delta/Velleman/K8800/Configuration_adv.h | 8 ++++---- config/examples/delta/generic/Configuration.h | 2 +- config/examples/delta/generic/Configuration_adv.h | 8 ++++---- config/examples/delta/kossel_clear/Configuration.h | 2 +- config/examples/delta/kossel_clear/Configuration_adv.h | 8 ++++---- config/examples/delta/kossel_mini/Configuration.h | 2 +- config/examples/delta/kossel_mini/Configuration_adv.h | 8 ++++---- config/examples/delta/kossel_pro/Configuration.h | 2 +- config/examples/delta/kossel_pro/Configuration_adv.h | 8 ++++---- config/examples/delta/kossel_xl/Configuration.h | 2 +- config/examples/delta/kossel_xl/Configuration_adv.h | 8 ++++---- config/examples/gCreate/gMax1.5+/Configuration.h | 2 +- config/examples/gCreate/gMax1.5+/Configuration_adv.h | 8 ++++---- .../linear_axes/Octopus 8 LINEAR_AXES/Configuration.h | 2 +- .../linear_axes/Octopus 8 LINEAR_AXES/Configuration_adv.h | 8 ++++---- .../linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h | 2 +- .../linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h | 8 ++++---- config/examples/makibox/Configuration.h | 2 +- config/examples/makibox/Configuration_adv.h | 8 ++++---- config/examples/tvrrug/Round2/Configuration.h | 2 +- config/examples/tvrrug/Round2/Configuration_adv.h | 8 ++++---- 800 files changed, 2000 insertions(+), 2000 deletions(-) diff --git a/config/default/Configuration.h b/config/default/Configuration.h index ebedc482da..985f27e282 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index ff68f2e145..f64ee9def4 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4285,7 +4285,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index 1fc2c15145..5e5a0fa2b9 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 0364b3710b..8436711808 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4302,7 +4302,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/3DMatik/XL/Configuration.h b/config/examples/3DMatik/XL/Configuration.h index 3d905632e7..b245e9e0b3 100644 --- a/config/examples/3DMatik/XL/Configuration.h +++ b/config/examples/3DMatik/XL/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/3DMatik/XL/Configuration_adv.h b/config/examples/3DMatik/XL/Configuration_adv.h index f9507de7aa..16982099a6 100644 --- a/config/examples/3DMatik/XL/Configuration_adv.h +++ b/config/examples/3DMatik/XL/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index db7374cc83..f8cea9b820 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index c6b4b9b7eb..4c03703b6a 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index 09f68d8294..e7bb26c776 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index e1d42c0e0c..63603f81b0 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index 01b1cf1607..800d1abca9 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -1020,7 +1020,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index 37510dfa9d..0518183260 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1183,7 +1183,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4316,7 +4316,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 7acafddb58..7c7af7c896 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -1021,7 +1021,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index bc503233ac..1c4372ff0d 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 31d47eb7bb..e1e7b40001 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AliExpress/CL-260/Configuration_adv.h b/config/examples/AliExpress/CL-260/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/AliExpress/CL-260/Configuration_adv.h +++ b/config/examples/AliExpress/CL-260/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 313c2ece1b..0f0c3d18db 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index 546c0a3cce..6b3d995ce5 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. #define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index 280e9b583c..03668d7197 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 2c1836da3d..a2e60da243 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 24fe946f6b..f836c09cda 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 2c1836da3d..a2e60da243 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 85d6faff2f..6fbc664d61 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 56a881a553..ce93848ad4 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 3b2f4c1406..d90254024f 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 64cbd008d8..992348f94d 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 0bb0aa3e9a..aa68660fd9 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index a486ffa52f..864bc48ee8 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h index 17bb857832..259da24de4 100644 --- a/config/examples/Anet/A9/Configuration.h +++ b/config/examples/Anet/A9/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/A9/Configuration_adv.h b/config/examples/Anet/A9/Configuration_adv.h index aa11ce6589..3e18109187 100644 --- a/config/examples/Anet/A9/Configuration_adv.h +++ b/config/examples/Anet/A9/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index 08b3db8240..963c0a7a0b 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index 6583ac347c..c1667623c0 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h index b5f72ec4b8..1ec5653f73 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h index da106a1bc2..9b9dc29174 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h index 0213ee2911..2cd6eb3526 100644 --- a/config/examples/Anet/E16/Stock/Configuration.h +++ b/config/examples/Anet/E16/Stock/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/E16/Stock/Configuration_adv.h b/config/examples/Anet/E16/Stock/Configuration_adv.h index 54cb440b04..36d19e026a 100644 --- a/config/examples/Anet/E16/Stock/Configuration_adv.h +++ b/config/examples/Anet/E16/Stock/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET4+/Configuration.h b/config/examples/Anet/ET4+/Configuration.h index d3fc19e088..5710427d9b 100644 --- a/config/examples/Anet/ET4+/Configuration.h +++ b/config/examples/Anet/ET4+/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET4+/Configuration_adv.h b/config/examples/Anet/ET4+/Configuration_adv.h index f19c559c6f..5ae77c57ef 100644 --- a/config/examples/Anet/ET4+/Configuration_adv.h +++ b/config/examples/Anet/ET4+/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET4-Pro/Configuration.h b/config/examples/Anet/ET4-Pro/Configuration.h index 6ef12c8cb2..0c4aab1e31 100644 --- a/config/examples/Anet/ET4-Pro/Configuration.h +++ b/config/examples/Anet/ET4-Pro/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET4-Pro/Configuration_adv.h b/config/examples/Anet/ET4-Pro/Configuration_adv.h index f19c559c6f..5ae77c57ef 100644 --- a/config/examples/Anet/ET4-Pro/Configuration_adv.h +++ b/config/examples/Anet/ET4-Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h index 01f368778e..9a66f37bc4 100644 --- a/config/examples/Anet/ET4/Configuration.h +++ b/config/examples/Anet/ET4/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET4/Configuration_adv.h b/config/examples/Anet/ET4/Configuration_adv.h index f19c559c6f..5ae77c57ef 100644 --- a/config/examples/Anet/ET4/Configuration_adv.h +++ b/config/examples/Anet/ET4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET4X/Configuration.h b/config/examples/Anet/ET4X/Configuration.h index 638c5ad54d..e15c8616ae 100644 --- a/config/examples/Anet/ET4X/Configuration.h +++ b/config/examples/Anet/ET4X/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET4X/Configuration_adv.h b/config/examples/Anet/ET4X/Configuration_adv.h index f19c559c6f..5ae77c57ef 100644 --- a/config/examples/Anet/ET4X/Configuration_adv.h +++ b/config/examples/Anet/ET4X/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET5-Pro/Configuration.h b/config/examples/Anet/ET5-Pro/Configuration.h index e28ca0aa8b..1933dc3206 100644 --- a/config/examples/Anet/ET5-Pro/Configuration.h +++ b/config/examples/Anet/ET5-Pro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET5-Pro/Configuration_adv.h b/config/examples/Anet/ET5-Pro/Configuration_adv.h index 4d74a11823..d9451bd7a4 100644 --- a/config/examples/Anet/ET5-Pro/Configuration_adv.h +++ b/config/examples/Anet/ET5-Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4303,7 +4303,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET5/Configuration.h b/config/examples/Anet/ET5/Configuration.h index 9707d1df54..a4736ba00e 100644 --- a/config/examples/Anet/ET5/Configuration.h +++ b/config/examples/Anet/ET5/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET5/Configuration_adv.h b/config/examples/Anet/ET5/Configuration_adv.h index 4d74a11823..d9451bd7a4 100644 --- a/config/examples/Anet/ET5/Configuration_adv.h +++ b/config/examples/Anet/ET5/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4303,7 +4303,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Anet/ET5X/Configuration.h b/config/examples/Anet/ET5X/Configuration.h index 0549837586..e37a183b77 100644 --- a/config/examples/Anet/ET5X/Configuration.h +++ b/config/examples/Anet/ET5X/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Anet/ET5X/Configuration_adv.h b/config/examples/Anet/ET5X/Configuration_adv.h index 4d74a11823..d9451bd7a4 100644 --- a/config/examples/Anet/ET5X/Configuration_adv.h +++ b/config/examples/Anet/ET5X/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4303,7 +4303,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h index c58426a575..2d942ab1a7 100644 --- a/config/examples/AnyCubic/Chiron/Configuration.h +++ b/config/examples/AnyCubic/Chiron/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/Chiron/Configuration_adv.h b/config/examples/AnyCubic/Chiron/Configuration_adv.h index 98d40db7ff..f962c05eab 100644 --- a/config/examples/AnyCubic/Chiron/Configuration_adv.h +++ b/config/examples/AnyCubic/Chiron/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h index 20a92386d0..69c5567279 100644 --- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h index 4cbb893db3..d96d5b590a 100644 --- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h index e3692bf9d7..4981ee76ed 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h index 124e81efa5..86270cb11e 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h index ef5cea9c8c..7f5424a344 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h index 1dac7ca93a..d5a08a34f0 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/Vyper/Configuration.h b/config/examples/AnyCubic/Vyper/Configuration.h index d148fd3435..123b70dc96 100644 --- a/config/examples/AnyCubic/Vyper/Configuration.h +++ b/config/examples/AnyCubic/Vyper/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/Vyper/Configuration_adv.h b/config/examples/AnyCubic/Vyper/Configuration_adv.h index 3dfc0a39d7..1fcd21b1a7 100644 --- a/config/examples/AnyCubic/Vyper/Configuration_adv.h +++ b/config/examples/AnyCubic/Vyper/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h b/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h index b69531684f..388712dfd2 100644 --- a/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h @@ -990,7 +990,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration_adv.h b/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration_adv.h index da12018922..119ca95eb6 100644 --- a/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration_adv.h +++ b/config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h b/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h index a2e9d408bf..138ff2a9be 100644 --- a/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration_adv.h b/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration_adv.h index c27deb18b9..7862f9feb9 100644 --- a/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration_adv.h +++ b/config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 6b3b0e28f5..0929b6b00a 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 6cc138872f..2a14ed2f47 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 0a6123c4ea..688cb2557d 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index d439863304..f9fcb8aceb 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -302,7 +302,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -783,7 +783,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1179,7 +1179,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4311,7 +4311,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Genius Pro/Configuration.h b/config/examples/Artillery/Genius Pro/Configuration.h index 4ba16b82d9..6b228fb2a2 100644 --- a/config/examples/Artillery/Genius Pro/Configuration.h +++ b/config/examples/Artillery/Genius Pro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Genius Pro/Configuration_adv.h b/config/examples/Artillery/Genius Pro/Configuration_adv.h index 7b01b6f793..199eaf008c 100644 --- a/config/examples/Artillery/Genius Pro/Configuration_adv.h +++ b/config/examples/Artillery/Genius Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Genius/BLTouch/Configuration.h b/config/examples/Artillery/Genius/BLTouch/Configuration.h index e033c0ef4b..c4350d6caf 100644 --- a/config/examples/Artillery/Genius/BLTouch/Configuration.h +++ b/config/examples/Artillery/Genius/BLTouch/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h b/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h index 7b21764c6c..4035ca1913 100644 --- a/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h +++ b/config/examples/Artillery/Genius/BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Genius/V1/Configuration.h b/config/examples/Artillery/Genius/V1/Configuration.h index 9cee103f93..af064e038d 100644 --- a/config/examples/Artillery/Genius/V1/Configuration.h +++ b/config/examples/Artillery/Genius/V1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Genius/V1/Configuration_adv.h b/config/examples/Artillery/Genius/V1/Configuration_adv.h index f4f9ca6ccd..7717c04498 100644 --- a/config/examples/Artillery/Genius/V1/Configuration_adv.h +++ b/config/examples/Artillery/Genius/V1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Hornet/Configuration.h b/config/examples/Artillery/Hornet/Configuration.h index 1403143744..4d382be3a6 100644 --- a/config/examples/Artillery/Hornet/Configuration.h +++ b/config/examples/Artillery/Hornet/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Hornet/Configuration_adv.h b/config/examples/Artillery/Hornet/Configuration_adv.h index 8e4097d357..31531d3a82 100644 --- a/config/examples/Artillery/Hornet/Configuration_adv.h +++ b/config/examples/Artillery/Hornet/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h index 4926d0c8bd..d4f91e90cc 100644 --- a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h @@ -966,7 +966,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h index cb79d5a3aa..309de8641e 100644 --- a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h index 52a02b6dfd..cd9963ccd5 100644 --- a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h index f4f9ca6ccd..7717c04498 100644 --- a/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Artillery/Sidewinder X2/Configuration.h b/config/examples/Artillery/Sidewinder X2/Configuration.h index 3a58fad273..5d02cfb688 100644 --- a/config/examples/Artillery/Sidewinder X2/Configuration.h +++ b/config/examples/Artillery/Sidewinder X2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Artillery/Sidewinder X2/Configuration_adv.h b/config/examples/Artillery/Sidewinder X2/Configuration_adv.h index 770ec2a510..b56b3582ae 100644 --- a/config/examples/Artillery/Sidewinder X2/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 8c411822a6..f195bf9b1b 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Azteeg/X5GT/Configuration_adv.h b/config/examples/Azteeg/X5GT/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Azteeg/X5GT/Configuration_adv.h +++ b/config/examples/Azteeg/X5GT/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 815e6f228a..04144ee7cd 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index bb854d57e5..2725f5d69d 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIBO/TouchX/default - BLTouch/Configuration.h b/config/examples/BIBO/TouchX/default - BLTouch/Configuration.h index 0550ff1231..8f2b9837c2 100644 --- a/config/examples/BIBO/TouchX/default - BLTouch/Configuration.h +++ b/config/examples/BIBO/TouchX/default - BLTouch/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIBO/TouchX/default - BLTouch/Configuration_adv.h b/config/examples/BIBO/TouchX/default - BLTouch/Configuration_adv.h index cd446070a1..fa0be6889a 100644 --- a/config/examples/BIBO/TouchX/default - BLTouch/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default - BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 7accc5e435..f3b6b96f0a 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 9e55bdf714..637cd0b5bc 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4303,7 +4303,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIQU/B1 SE Plus/Configuration.h b/config/examples/BIQU/B1 SE Plus/Configuration.h index cc6d98fb79..4d904fada2 100644 --- a/config/examples/BIQU/B1 SE Plus/Configuration.h +++ b/config/examples/BIQU/B1 SE Plus/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIQU/B1 SE Plus/Configuration_adv.h b/config/examples/BIQU/B1 SE Plus/Configuration_adv.h index 5ff1f067bb..324bd63cbd 100644 --- a/config/examples/BIQU/B1 SE Plus/Configuration_adv.h +++ b/config/examples/BIQU/B1 SE Plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIQU/B1 SE/Configuration.h b/config/examples/BIQU/B1 SE/Configuration.h index 45c911d8b2..dbc6860b18 100644 --- a/config/examples/BIQU/B1 SE/Configuration.h +++ b/config/examples/BIQU/B1 SE/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIQU/B1 SE/Configuration_adv.h b/config/examples/BIQU/B1 SE/Configuration_adv.h index 5052f032ea..40b65892eb 100644 --- a/config/examples/BIQU/B1 SE/Configuration_adv.h +++ b/config/examples/BIQU/B1 SE/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIQU/B1/Configuration.h b/config/examples/BIQU/B1/Configuration.h index b7a3bf4008..eb2d0eb99b 100644 --- a/config/examples/BIQU/B1/Configuration.h +++ b/config/examples/BIQU/B1/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIQU/B1/Configuration_adv.h b/config/examples/BIQU/B1/Configuration_adv.h index 36b689fd2f..4d65e5fa03 100644 --- a/config/examples/BIQU/B1/Configuration_adv.h +++ b/config/examples/BIQU/B1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIQU/BX/Configuration.h b/config/examples/BIQU/BX/Configuration.h index 230016f05d..41c8f5e334 100644 --- a/config/examples/BIQU/BX/Configuration.h +++ b/config/examples/BIQU/BX/Configuration.h @@ -971,7 +971,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIQU/BX/Configuration_adv.h b/config/examples/BIQU/BX/Configuration_adv.h index 4d71ace86a..94ba9f2092 100644 --- a/config/examples/BIQU/BX/Configuration_adv.h +++ b/config/examples/BIQU/BX/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1175,7 +1175,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIQU/Hurakan/Configuration.h b/config/examples/BIQU/Hurakan/Configuration.h index f9fe8a1ce7..87beeed067 100644 --- a/config/examples/BIQU/Hurakan/Configuration.h +++ b/config/examples/BIQU/Hurakan/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIQU/Hurakan/Configuration_adv.h b/config/examples/BIQU/Hurakan/Configuration_adv.h index 526af6fa74..e4cdfeabbf 100644 --- a/config/examples/BIQU/Hurakan/Configuration_adv.h +++ b/config/examples/BIQU/Hurakan/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1175,7 +1175,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BIQU/Thunder Standard/Configuration.h b/config/examples/BIQU/Thunder Standard/Configuration.h index 0669706d2f..520ecb07e0 100644 --- a/config/examples/BIQU/Thunder Standard/Configuration.h +++ b/config/examples/BIQU/Thunder Standard/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BIQU/Thunder Standard/Configuration_adv.h b/config/examples/BIQU/Thunder Standard/Configuration_adv.h index 43a2af3ff9..d07ec2e4bf 100644 --- a/config/examples/BIQU/Thunder Standard/Configuration_adv.h +++ b/config/examples/BIQU/Thunder Standard/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index a482b03bea..cc8c132843 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index 15c0ab5bf9..8648d81fd7 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index ecc77b1905..93a0871e31 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -965,7 +965,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index 956446bb1a..2c334de761 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4314,7 +4314,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 85a1107305..b136436464 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index 15c0ab5bf9..8648d81fd7 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/CNC/miniRambo/Configuration.h b/config/examples/CNC/miniRambo/Configuration.h index f488f7c210..9019ce2bca 100644 --- a/config/examples/CNC/miniRambo/Configuration.h +++ b/config/examples/CNC/miniRambo/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/CNC/miniRambo/Configuration_adv.h b/config/examples/CNC/miniRambo/Configuration_adv.h index b60c2fdc0f..3d7043e105 100644 --- a/config/examples/CNC/miniRambo/Configuration_adv.h +++ b/config/examples/CNC/miniRambo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/CTC/A13/Configuration.h b/config/examples/CTC/A13/Configuration.h index b23e70cae4..9cda67f2c2 100644 --- a/config/examples/CTC/A13/Configuration.h +++ b/config/examples/CTC/A13/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/CTC/A13/Configuration_adv.h b/config/examples/CTC/A13/Configuration_adv.h index 70f53e13df..249fa6a617 100644 --- a/config/examples/CTC/A13/Configuration_adv.h +++ b/config/examples/CTC/A13/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/CTC/Bizer/Configuration.h b/config/examples/CTC/Bizer/Configuration.h index 27be5ee7be..b8a58bf3e1 100644 --- a/config/examples/CTC/Bizer/Configuration.h +++ b/config/examples/CTC/Bizer/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/CTC/Bizer/Configuration_adv.h b/config/examples/CTC/Bizer/Configuration_adv.h index cfb69d694d..af96264cd0 100644 --- a/config/examples/CTC/Bizer/Configuration_adv.h +++ b/config/examples/CTC/Bizer/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index c01579a973..ddd0951eb0 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration_adv.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration_adv.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index 3260d4cf81..faf4d9018a 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -967,7 +967,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index b0e45c39b1..208a7985c9 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index ae5a76d59f..6b88b3c6b2 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Copymaster3D/300/Configuration_adv.h b/config/examples/Copymaster3D/300/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Copymaster3D/300/Configuration_adv.h +++ b/config/examples/Copymaster3D/300/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 0c84edbb36..eedf19200a 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Copymaster3D/400/Configuration_adv.h b/config/examples/Copymaster3D/400/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Copymaster3D/400/Configuration_adv.h +++ b/config/examples/Copymaster3D/400/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index 7376fb9636..8a5935572b 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Copymaster3D/500/Configuration_adv.h b/config/examples/Copymaster3D/500/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Copymaster3D/500/Configuration_adv.h +++ b/config/examples/Copymaster3D/500/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 Max/Configuration.h b/config/examples/Creality/CR-10 Max/Configuration.h index 25868be8c0..7c7b03e10e 100644 --- a/config/examples/Creality/CR-10 Max/Configuration.h +++ b/config/examples/Creality/CR-10 Max/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 Max/Configuration_adv.h b/config/examples/Creality/CR-10 Max/Configuration_adv.h index 1db4e6a1c5..5eb2e690f9 100644 --- a/config/examples/Creality/CR-10 Max/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Max/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h index 5b79cafedb..cae874711b 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 4985d389bd..bd3e97c4ea 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration.h index ab495d4549..c66a954202 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index b031c32533..1fa511d51f 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h index cd9cf943d6..11eec65ff6 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h @@ -960,7 +960,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h index 345f51b6a3..f358c575fe 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h index 5d6e243cb4..71217c85de 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h index 60a4e93394..97da6f5586 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -777,7 +777,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1173,7 +1173,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4301,7 +4301,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h index 307cf24d6f..914e2428c0 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h index a645a0921e..15133f36ce 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h index 1cb949c27c..b0052dbbb0 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h index 69057289ad..e2e0564f1a 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h index 81f90597c0..53870fe247 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration_adv.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration_adv.h index 22d7086b24..dfcb7950f4 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h index 0d843844e3..46255d1cc3 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h index a645a0921e..15133f36ce 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration.h index 4d1c1dfc31..67e2d547aa 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration_adv.h b/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration_adv.h index 6775dc9e2f..0e29616e10 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration.h index e3145a6426..d935e0678e 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration_adv.h b/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration_adv.h index cc17c6aeea..0a6c3bc1aa 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index 972f874b99..2d228d2b22 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -960,7 +960,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 V2/Configuration_adv.h b/config/examples/Creality/CR-10 V2/Configuration_adv.h index 3355fa0af9..06f259b60d 100644 --- a/config/examples/Creality/CR-10 V2/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration.h b/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration.h index 252fe801fd..84c458b4c2 100644 --- a/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration.h +++ b/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration.h @@ -960,7 +960,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration_adv.h b/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration_adv.h index dd62c1546c..af57419361 100644 --- a/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4311,7 +4311,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10 V3/Stock/Configuration.h b/config/examples/Creality/CR-10 V3/Stock/Configuration.h index 8a35b0c7f7..d7e46338e5 100644 --- a/config/examples/Creality/CR-10 V3/Stock/Configuration.h +++ b/config/examples/Creality/CR-10 V3/Stock/Configuration.h @@ -960,7 +960,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10 V3/Stock/Configuration_adv.h b/config/examples/Creality/CR-10 V3/Stock/Configuration_adv.h index 506203815c..4554214f2f 100644 --- a/config/examples/Creality/CR-10 V3/Stock/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V3/Stock/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4311,7 +4311,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h index 28b95528f1..b51b7942dc 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 7138ec4f10..8177424a9e 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h index 66e2469118..be3b61ef1f 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index 86f6a41f85..d81ab6808b 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h index 3a7a24b943..58a4a7f42a 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h index cdd5337e3a..b0f0a0a12f 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S Pro/Configuration.h b/config/examples/Creality/CR-10S Pro/Configuration.h index 55943fa730..6334050b21 100644 --- a/config/examples/Creality/CR-10S Pro/Configuration.h +++ b/config/examples/Creality/CR-10S Pro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S Pro/Configuration_adv.h b/config/examples/Creality/CR-10S Pro/Configuration_adv.h index 9754217e89..398f136499 100644 --- a/config/examples/Creality/CR-10S Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-10S Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h index 8c9a6b9bee..5729c10e23 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h index 1aeedbc249..9f63c40686 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h index 03796bb986..dade8300a5 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h index 8b4240656f..12cec5b712 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h index 97b3c91eae..e4d2447fea 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 7138ec4f10..8177424a9e 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration.h index f9b6f59f68..51fe1aff11 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index 668ef45795..fdb45451e2 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h index f2f36ad78d..673edf66d8 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h index 01e5aa2faf..cc26203f98 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration.h index 27cbe9a032..19356cea56 100644 --- a/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration_adv.h b/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration_adv.h index abd77540c0..f6c18ccb55 100644 --- a/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h index 3507c0765d..56bda4e120 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h index 5254a7ced7..d8bdfb83d6 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index 1d53ce6244..8017a8ced3 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 0ea044b346..59dfaba4f1 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration.h b/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration.h index c299750408..f6a7d1d5d1 100644 --- a/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration.h +++ b/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration_adv.h b/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration_adv.h index ca5f37c7fa..475931cf29 100644 --- a/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-20/Stock/Configuration.h b/config/examples/Creality/CR-20/Stock/Configuration.h index b99227d940..0789a577ba 100644 --- a/config/examples/Creality/CR-20/Stock/Configuration.h +++ b/config/examples/Creality/CR-20/Stock/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-20/Stock/Configuration_adv.h b/config/examples/Creality/CR-20/Stock/Configuration_adv.h index ca5f37c7fa..475931cf29 100644 --- a/config/examples/Creality/CR-20/Stock/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Stock/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration.h b/config/examples/Creality/CR-30 PrintMill/Configuration.h index 7a38b27103..a6bf8704b5 100644 --- a/config/examples/Creality/CR-30 PrintMill/Configuration.h +++ b/config/examples/Creality/CR-30 PrintMill/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h b/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h index 18f66b22b0..47d53c4554 100644 --- a/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h +++ b/config/examples/Creality/CR-30 PrintMill/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h index fa23358c65..05d2190a05 100644 --- a/config/examples/Creality/CR-6 SE/Configuration.h +++ b/config/examples/Creality/CR-6 SE/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-6 SE/Configuration_adv.h b/config/examples/Creality/CR-6 SE/Configuration_adv.h index 79046daa01..78e924e88e 100644 --- a/config/examples/Creality/CR-6 SE/Configuration_adv.h +++ b/config/examples/Creality/CR-6 SE/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4293,7 +4293,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 46e4819b21..92326612b9 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 23fd7663ec..bf8c198558 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration.h b/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration.h index 9274e45504..0936c48829 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration_adv.h b/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration_adv.h index d1578d5407..fe286b4816 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration_adv.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h index 66ec5d19a5..8ccf792ad1 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h index d777d4912f..cbcddf1719 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 3f283d4116..990c7ad814 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 1fdaa2266b..c3f6ca70d0 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Max Neo/Configuration.h b/config/examples/Creality/Ender-3 Max Neo/Configuration.h index 548bbf2898..b059244438 100644 --- a/config/examples/Creality/Ender-3 Max Neo/Configuration.h +++ b/config/examples/Creality/Ender-3 Max Neo/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Max Neo/Configuration_adv.h b/config/examples/Creality/Ender-3 Max Neo/Configuration_adv.h index 14d18ea48c..187411ec56 100644 --- a/config/examples/Creality/Ender-3 Max Neo/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Max Neo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Max/Configuration.h b/config/examples/Creality/Ender-3 Max/Configuration.h index 9346b773b1..98df1d4290 100644 --- a/config/examples/Creality/Ender-3 Max/Configuration.h +++ b/config/examples/Creality/Ender-3 Max/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Max/Configuration_adv.h b/config/examples/Creality/Ender-3 Max/Configuration_adv.h index ec9dec2f50..6c79dcbb87 100644 --- a/config/examples/Creality/Ender-3 Max/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Max/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Neo/Configuration.h b/config/examples/Creality/Ender-3 Neo/Configuration.h index 598ac956a2..93b78f46ce 100644 --- a/config/examples/Creality/Ender-3 Neo/Configuration.h +++ b/config/examples/Creality/Ender-3 Neo/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Neo/Configuration_adv.h b/config/examples/Creality/Ender-3 Neo/Configuration_adv.h index 819dc0a1ca..e68622f7b6 100644 --- a/config/examples/Creality/Ender-3 Neo/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Neo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h index e469fecfbd..265dadd2d3 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h index cab846f2a1..fc6eb542fb 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h index 0615abba5e..5800cbe46f 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index aaf4d2b4e4..93eb02e259 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index 2b511d8682..d98b230e4d 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index aaf4d2b4e4..93eb02e259 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h index 69f69625d8..5a03a450a5 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index e800f889e9..b812130e0a 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h index 8c8a340255..4ab443cc59 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index b9ee4e36e9..0bc902a9b5 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration.h b/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration.h index 262de06fbf..84fc85a274 100644 --- a/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration_adv.h index 0b921077ea..eb38eb9fab 100644 --- a/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/Creality free-runs/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h index 7399957d98..80f2455986 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h index 1a60028c77..68e53cbff5 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h index 2f1982ba28..674a2a7e7a 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h index 4c967fbe38..d70eb594b0 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration.h index ba5138a4da..1f3e9f7a1f 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration_adv.h index e6d1d52f57..0677faa6d1 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427 - BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h index 630ce8488f..d7d86daf78 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h index 16ea0743f8..1ee4186f40 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 S1 Plus/Configuration.h b/config/examples/Creality/Ender-3 S1 Plus/Configuration.h index 6d1eafafe1..82d3b94671 100644 --- a/config/examples/Creality/Ender-3 S1 Plus/Configuration.h +++ b/config/examples/Creality/Ender-3 S1 Plus/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 S1 Plus/Configuration_adv.h b/config/examples/Creality/Ender-3 S1 Plus/Configuration_adv.h index 7be138867d..99b7c10e5e 100644 --- a/config/examples/Creality/Ender-3 S1 Plus/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 S1 Plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 S1 Pro/Configuration.h b/config/examples/Creality/Ender-3 S1 Pro/Configuration.h index 916c5506f0..ac7436abec 100644 --- a/config/examples/Creality/Ender-3 S1 Pro/Configuration.h +++ b/config/examples/Creality/Ender-3 S1 Pro/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 S1 Pro/Configuration_adv.h b/config/examples/Creality/Ender-3 S1 Pro/Configuration_adv.h index 7be138867d..99b7c10e5e 100644 --- a/config/examples/Creality/Ender-3 S1 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 S1 Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 S1/STM32F1/Configuration.h b/config/examples/Creality/Ender-3 S1/STM32F1/Configuration.h index 18b93c96ca..5e3557dd5a 100644 --- a/config/examples/Creality/Ender-3 S1/STM32F1/Configuration.h +++ b/config/examples/Creality/Ender-3 S1/STM32F1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 S1/STM32F1/Configuration_adv.h b/config/examples/Creality/Ender-3 S1/STM32F1/Configuration_adv.h index bf4c2d8f3e..f7ca5878e3 100644 --- a/config/examples/Creality/Ender-3 S1/STM32F1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 S1/STM32F1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 S1/STM32F4/Configuration.h b/config/examples/Creality/Ender-3 S1/STM32F4/Configuration.h index 9eca39e3a9..3c86c2d5ca 100644 --- a/config/examples/Creality/Ender-3 S1/STM32F4/Configuration.h +++ b/config/examples/Creality/Ender-3 S1/STM32F4/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 S1/STM32F4/Configuration_adv.h b/config/examples/Creality/Ender-3 S1/STM32F4/Configuration_adv.h index 5b10c1b2a6..a87e89411a 100644 --- a/config/examples/Creality/Ender-3 S1/STM32F4/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 S1/STM32F4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration.h index 494a945bc4..907532b396 100644 --- a/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index 143cba9691..13c93f9ab4 100644 --- a/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2 Neo/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration.h index 4c4e27ae90..3223936e47 100644 --- a/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration_adv.h index 74b65c93de..d4b634c583 100644 --- a/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2 Neo/CrealityV422/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h index 2b7f5ad338..f28a133fbb 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h index 707c2e7deb..be3c11ab73 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h index 45fde48270..665a5df112 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h index f98d6047bf..715623b654 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration.h index 7019b4ca9c..7c2c5fd1b6 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration_adv.h index c0021d4d68..56706b2c7f 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/CrealityUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration.h index 318ee97830..7ce872a4c8 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration_adv.h index d176c74b97..6d395da86d 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 2.0/MarlinUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration.h index 31f68fd1a5..b77be0e1b4 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration_adv.h index fea144c123..ec9a231e28 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/CrealityUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration.h index 315c3e2f52..67f28c5eee 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration_adv.h index 30043fd477..ea17dad509 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 3.0/MarlinUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h index d4d6322118..fc9a72c140 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h index d1144f1121..9a24606a8c 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h index ed515cea6b..25720a4978 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h index fc2ea6f51a..e2e296e65b 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration.h index cc5aaa6151..16087eefa4 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration_adv.h index 457aafc802..d9006dff4b 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV427/CrealityUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration.h index 8ba5aedc43..3d064fe375 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration_adv.h index a919c559f4..0a66be5eba 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV427/MarlinUI/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h index 2f311bbbe3..ebaf0f3088 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h index a2c46c90a0..acf122d255 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration.h index 6e76111ffe..5938548f9b 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration.h @@ -948,7 +948,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration_adv.h index e0596fc98f..b980799fa9 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech Manta E3 EZ/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h index e452353be4..8e742e1588 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h index f811c35917..ce8ae6afff 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h index 50abb0d790..266d6ec2b6 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h index caf29910a7..c08923b894 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h index e8c92915f6..6b00d26b2b 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h index 8a66a611f1..b59514a151 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h index 131d5dc8b5..2631092a9b 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h index caf29910a7..c08923b894 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h index 61f48e1d67..1267bd6c3a 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h index 2d0cb12ceb..808390df8b 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index b9800354e6..e6ee23aa03 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 5cf12c7e03..84115a7e28 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index dbe1701c78..2a9e418a79 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 5cf12c7e03..84115a7e28 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index 151564247f..dabc36fb10 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index b2d357b34a..e5039c0488 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h index ee0d8651b9..8d30b83814 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index b565951ad6..d5bc000970 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/Creality free-runs/Configuration.h b/config/examples/Creality/Ender-3/Creality free-runs/Configuration.h index 4aa0648887..7331cccb77 100644 --- a/config/examples/Creality/Ender-3/Creality free-runs/Configuration.h +++ b/config/examples/Creality/Ender-3/Creality free-runs/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/Creality free-runs/Configuration_adv.h b/config/examples/Creality/Ender-3/Creality free-runs/Configuration_adv.h index 0b921077ea..eb38eb9fab 100644 --- a/config/examples/Creality/Ender-3/Creality free-runs/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Creality free-runs/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index f1dd1f8d2a..7332616c97 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h index 1a60028c77..68e53cbff5 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h index 1b58e27ea1..3e4a0b41b0 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h index 84b1fa7a2c..47a20be27b 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h index 67a31e1395..1655bc9588 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h index 16ea0743f8..1ee4186f40 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index 48477efa38..e34bc17fc6 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h index 62b4f1260f..ab139a7223 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 240ad4ef59..f9fed7b26d 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h index 62b4f1260f..ab139a7223 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h index 08e1639f5b..d81be5cee2 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h index ea3b481672..8c195da43b 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index 10c67c8212..27687987eb 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h index 62b4f1260f..ab139a7223 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index d2dd456f68..16058aa55a 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h index 62b4f1260f..ab139a7223 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index ab36c4c430..b117235eda 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h index fdd99f6757..4b17c3bd98 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -777,7 +777,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1173,7 +1173,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4301,7 +4301,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h index cb6a32f68c..26e1d8109c 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h index b42272dafe..7dfb1da419 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h index 3a7bcb8d69..96dffc84fc 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h index 41d2b1a930..80b7bf822f 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h index 2323cb3339..3a2c2fab77 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h index c361d54f23..7c838b6fe6 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h index 8d0972b3e3..fc1faba5f0 100644 --- a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h +++ b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h index 66d994db4d..562f311747 100644 --- a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index 032ce7ad36..378ff22330 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index c0c488dad8..870a2b2ce7 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration.h b/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration.h index f4a53ef5c7..76ee42e343 100644 --- a/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration_adv.h index 3f74dff851..63d97f79b6 100644 --- a/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Plus/BigTreeTech SKR 3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration.h b/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration.h index 79737ddd9e..3bb46e0dcb 100644 --- a/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration_adv.h index 9027b86f25..7fda6a96f9 100644 --- a/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Plus/CrealityV1 (ORIGIN UI)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration.h b/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration.h index ad72312bf5..a4a9b8e6a0 100644 --- a/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration_adv.h index bda474fb0e..c41e728c33 100644 --- a/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Plus/CrealityV1 (RELOADED UI)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h index 3843455b02..de55d9109f 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h index 47fd346f13..a804a795e8 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index a03233e5f1..5cf71e3872 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 95012f16a0..beaab3978c 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h index 1139b5346a..fa369d8b3a 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h index ddab6db05e..3061c54480 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration.h index 799625cf28..568eb1b378 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration_adv.h index 13ec6d0c1c..00479c6253 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 3.0 with BLTouch-HighTemp/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h index 8b5515c885..c77bae8d25 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h index 98d887513a..defcf88663 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h index 9549486867..1fac023940 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h index c20e7098c7..cfbb9c3fe1 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h index f747c334bd..7d0a8f8e41 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h index 5d09fd381e..802b8a0037 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5 S1/Configuration.h b/config/examples/Creality/Ender-5 S1/Configuration.h index c2cb3feaae..9a76f4c253 100644 --- a/config/examples/Creality/Ender-5 S1/Configuration.h +++ b/config/examples/Creality/Ender-5 S1/Configuration.h @@ -968,7 +968,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5 S1/Configuration_adv.h b/config/examples/Creality/Ender-5 S1/Configuration_adv.h index 9384f00544..690a28f33e 100644 --- a/config/examples/Creality/Ender-5 S1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 S1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1177,7 +1177,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4310,7 +4310,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h index 603fdf4baf..40444a7840 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h index 47fd346f13..a804a795e8 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h index 189dd349ee..b7f50ee9da 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h index e6dd3b4064..4637a35cf7 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h index 220040b2c8..c374e74eeb 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 485a098525..8beea56512 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index 205e52e831..f0438b8514 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 32791cba84..6e5a3658f0 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration.h index 1d4d13261f..0bd493ecf6 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration_adv.h index 387260d062..867d342e58 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 3.0 with BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/Creality free-runs/Configuration.h b/config/examples/Creality/Ender-5/Creality free-runs/Configuration.h index 74a98b46fe..84d85db783 100644 --- a/config/examples/Creality/Ender-5/Creality free-runs/Configuration.h +++ b/config/examples/Creality/Ender-5/Creality free-runs/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/Creality free-runs/Configuration_adv.h b/config/examples/Creality/Ender-5/Creality free-runs/Configuration_adv.h index 495504d6e0..d2e01de1b0 100644 --- a/config/examples/Creality/Ender-5/Creality free-runs/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Creality free-runs/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h index 04362a61c8..9bcad16732 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h index 36fcf460ae..96533506d5 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration.h index 204b1867b9..e84d9f5ad0 100644 --- a/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration_adv.h index 442f16f4a5..960124eccc 100644 --- a/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV427 with BLTouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h index 08c98ac70d..5bb19aa040 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h index eb6b0bec81..baa808a81e 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Creality/Ender-6/Configuration.h b/config/examples/Creality/Ender-6/Configuration.h index 23aa2beb69..3bba6b0345 100644 --- a/config/examples/Creality/Ender-6/Configuration.h +++ b/config/examples/Creality/Ender-6/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Creality/Ender-6/Configuration_adv.h b/config/examples/Creality/Ender-6/Configuration_adv.h index 7510d6a863..08a62ad6e4 100644 --- a/config/examples/Creality/Ender-6/Configuration_adv.h +++ b/config/examples/Creality/Ender-6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index cc251e9905..0d57d456ba 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 9fdd30ec56..eace4c743f 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index b25442fbdd..600f0f3c2b 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Daycom/3DP-100/Configuration_adv.h b/config/examples/Daycom/3DP-100/Configuration_adv.h index f5d56a4084..9c1dec67f3 100644 --- a/config/examples/Daycom/3DP-100/Configuration_adv.h +++ b/config/examples/Daycom/3DP-100/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/E3D/BigBox Dual/Configuration.h b/config/examples/E3D/BigBox Dual/Configuration.h index f550242c32..095918a293 100644 --- a/config/examples/E3D/BigBox Dual/Configuration.h +++ b/config/examples/E3D/BigBox Dual/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/E3D/BigBox Dual/Configuration_adv.h b/config/examples/E3D/BigBox Dual/Configuration_adv.h index a122c72985..aa049096f2 100644 --- a/config/examples/E3D/BigBox Dual/Configuration_adv.h +++ b/config/examples/E3D/BigBox Dual/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 1c2947e71a..c9434041a4 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index c092190744..ba3cf36e0b 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4303,7 +4303,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h index 8274e6fda1..8cb3dd05b3 100644 --- a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h +++ b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h b/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h index 579f9a2f24..ca191a219a 100644 --- a/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h +++ b/config/examples/EasyThreeD/ET4000PLUS/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Eazao/Zero/Configuration.h b/config/examples/Eazao/Zero/Configuration.h index aab26445a7..87c620fd08 100644 --- a/config/examples/Eazao/Zero/Configuration.h +++ b/config/examples/Eazao/Zero/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Eazao/Zero/Configuration_adv.h b/config/examples/Eazao/Zero/Configuration_adv.h index aca8512df1..145b7f906f 100644 --- a/config/examples/Eazao/Zero/Configuration_adv.h +++ b/config/examples/Eazao/Zero/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 1f7e7d128f..478fe332c9 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 129a5ca992..5fbd637d31 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Elegoo/Neptune 2/Configuration.h b/config/examples/Elegoo/Neptune 2/Configuration.h index 094fbccdca..24ec9ed0d7 100644 --- a/config/examples/Elegoo/Neptune 2/Configuration.h +++ b/config/examples/Elegoo/Neptune 2/Configuration.h @@ -987,7 +987,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Elegoo/Neptune 2/Configuration_adv.h b/config/examples/Elegoo/Neptune 2/Configuration_adv.h index b154caaf06..2ee9e733ec 100644 --- a/config/examples/Elegoo/Neptune 2/Configuration_adv.h +++ b/config/examples/Elegoo/Neptune 2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Eryone/Thinker SE/Configuration.h b/config/examples/Eryone/Thinker SE/Configuration.h index c4f10873d2..3c890b7cac 100644 --- a/config/examples/Eryone/Thinker SE/Configuration.h +++ b/config/examples/Eryone/Thinker SE/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Eryone/Thinker SE/Configuration_adv.h b/config/examples/Eryone/Thinker SE/Configuration_adv.h index b615cecc00..f093f08afd 100644 --- a/config/examples/Eryone/Thinker SE/Configuration_adv.h +++ b/config/examples/Eryone/Thinker SE/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4312,7 +4312,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Eryone/Thinker V2/Configuration.h b/config/examples/Eryone/Thinker V2/Configuration.h index c3b3762f46..c6c7ac2b93 100644 --- a/config/examples/Eryone/Thinker V2/Configuration.h +++ b/config/examples/Eryone/Thinker V2/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Eryone/Thinker V2/Configuration_adv.h b/config/examples/Eryone/Thinker V2/Configuration_adv.h index 080c413ae7..b649bbaf2c 100644 --- a/config/examples/Eryone/Thinker V2/Configuration_adv.h +++ b/config/examples/Eryone/Thinker V2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4312,7 +4312,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index bca3337b54..884ff32ce5 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 50bafa5b71..1748272914 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 616763f40d..48d70e9433 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index 890efe384b..a3c2cf0db2 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index 06dc79b2ef..124c677a3d 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index 441fdd360d..0d46a5a5fd 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 5ff818eb75..6122bd660e 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index b0c282078c..7991230e43 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index 6e05a75eea..e565bb8984 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index b0c282078c..7991230e43 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index 509748784c..a8209a089e 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FlashForge/Creator 2X/Configuration_adv.h b/config/examples/FlashForge/Creator 2X/Configuration_adv.h index 5376582eb4..342b9c4c85 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration_adv.h +++ b/config/examples/FlashForge/Creator 2X/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index 40bfb6501b..3e4c49896c 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 6e7559a6c0..1bb06eb94f 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -780,7 +780,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration.h b/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration.h index 6d72b98578..d70094ca2a 100644 --- a/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration.h +++ b/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration_adv.h b/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration_adv.h index 0b191ee700..a5269d77be 100644 --- a/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration_adv.h +++ b/config/examples/FlyingBear/FlyingBearGhost_v3/Configuration_adv.h @@ -295,7 +295,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -776,7 +776,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1172,7 +1172,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FlyingBear/P902/Configuration.h b/config/examples/FlyingBear/P902/Configuration.h index 696c7ea7f1..cc330b1a6f 100644 --- a/config/examples/FlyingBear/P902/Configuration.h +++ b/config/examples/FlyingBear/P902/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FlyingBear/P902/Configuration_adv.h b/config/examples/FlyingBear/P902/Configuration_adv.h index 30dd84921a..c9b519ab7c 100644 --- a/config/examples/FlyingBear/P902/Configuration_adv.h +++ b/config/examples/FlyingBear/P902/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. #define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index 1d05682cef..6074851b35 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FlyingBear/P905H/Configuration_adv.h b/config/examples/FlyingBear/P905H/Configuration_adv.h index 4777e87a56..503bd99cd2 100644 --- a/config/examples/FlyingBear/P905H/Configuration_adv.h +++ b/config/examples/FlyingBear/P905H/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FoamCutter/generic/Configuration.h b/config/examples/FoamCutter/generic/Configuration.h index 5ee14b33e2..d847b1d7aa 100644 --- a/config/examples/FoamCutter/generic/Configuration.h +++ b/config/examples/FoamCutter/generic/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FoamCutter/generic/Configuration_adv.h b/config/examples/FoamCutter/generic/Configuration_adv.h index 5544b33179..31f9f18631 100644 --- a/config/examples/FoamCutter/generic/Configuration_adv.h +++ b/config/examples/FoamCutter/generic/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4314,7 +4314,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FoamCutter/rcKeith/Configuration.h b/config/examples/FoamCutter/rcKeith/Configuration.h index bc5b55d46c..ecdc777d25 100644 --- a/config/examples/FoamCutter/rcKeith/Configuration.h +++ b/config/examples/FoamCutter/rcKeith/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FoamCutter/rcKeith/Configuration_adv.h b/config/examples/FoamCutter/rcKeith/Configuration_adv.h index 5544b33179..31f9f18631 100644 --- a/config/examples/FoamCutter/rcKeith/Configuration_adv.h +++ b/config/examples/FoamCutter/rcKeith/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4314,7 +4314,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FolgerTech/FT-5 R2/Configuration.h b/config/examples/FolgerTech/FT-5 R2/Configuration.h index 96393410eb..5057ed8d9d 100644 --- a/config/examples/FolgerTech/FT-5 R2/Configuration.h +++ b/config/examples/FolgerTech/FT-5 R2/Configuration.h @@ -948,7 +948,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FolgerTech/FT-5 R2/Configuration_adv.h b/config/examples/FolgerTech/FT-5 R2/Configuration_adv.h index 2ba4d946b1..351b82a7f9 100644 --- a/config/examples/FolgerTech/FT-5 R2/Configuration_adv.h +++ b/config/examples/FolgerTech/FT-5 R2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 8d23c0249f..3caf049264 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index ac838009dd..0ece499a2b 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 5d4e2ff54c..b8d502a2ce 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -1010,7 +1010,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 3338275a80..0f8783953f 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4311,7 +4311,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index b309d1f789..10500177a5 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index fdbb7a37c2..07f092d822 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index d4f687100b..41280ae8b7 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index 89dde2106c..9789304755 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h index d09970fd86..ff75532f9c 100644 --- a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h index 4a650820ff..bddc6e9d34 100644 --- a/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h index edd6a1d885..7698b33b61 100644 --- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h index 4a650820ff..bddc6e9d34 100644 --- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10PRO/Configuration.h b/config/examples/Geeetech/A10PRO/Configuration.h index 5890af81e6..5a25c0aa88 100644 --- a/config/examples/Geeetech/A10PRO/Configuration.h +++ b/config/examples/Geeetech/A10PRO/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10PRO/Configuration_adv.h b/config/examples/Geeetech/A10PRO/Configuration_adv.h index fdbb7a37c2..07f092d822 100644 --- a/config/examples/Geeetech/A10PRO/Configuration_adv.h +++ b/config/examples/Geeetech/A10PRO/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h index 2af69495e0..64934f077b 100644 --- a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h index 4a650820ff..bddc6e9d34 100644 --- a/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h index b2e82ae2be..def6997bc3 100644 --- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h index 4a650820ff..bddc6e9d34 100644 --- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index 4a9ca9ff04..11d09abb15 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index 9ac2e85851..743f2c66c0 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index beda5fdfd1..a7b3baf848 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 9ac2e85851..743f2c66c0 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index ed573569e6..c9670f32eb 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index 9ac2e85851..743f2c66c0 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 49522bb5b7..bd81bcdfc2 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 6eada5b5ba..7a256c4afe 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A30M/Configuration.h b/config/examples/Geeetech/A30M/Configuration.h index 75214a6576..97553de902 100644 --- a/config/examples/Geeetech/A30M/Configuration.h +++ b/config/examples/Geeetech/A30M/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A30M/Configuration_adv.h b/config/examples/Geeetech/A30M/Configuration_adv.h index 6eada5b5ba..7a256c4afe 100644 --- a/config/examples/Geeetech/A30M/Configuration_adv.h +++ b/config/examples/Geeetech/A30M/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/A30T/Configuration.h b/config/examples/Geeetech/A30T/Configuration.h index 093cb44ac1..8c6b070501 100644 --- a/config/examples/Geeetech/A30T/Configuration.h +++ b/config/examples/Geeetech/A30T/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/A30T/Configuration_adv.h b/config/examples/Geeetech/A30T/Configuration_adv.h index 6eada5b5ba..7a256c4afe 100644 --- a/config/examples/Geeetech/A30T/Configuration_adv.h +++ b/config/examples/Geeetech/A30T/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index 98a46ecc75..428a487d6c 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 6adb55f0ff..1912063d5d 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index c1f2041d04..55c2cbf47c 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index 441fdd360d..0d46a5a5fd 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index afb079bc02..cb110c5bcd 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index 6eada5b5ba..7a256c4afe 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 848e3d9e72..b5e8c25510 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/GT2560/Configuration_adv.h b/config/examples/Geeetech/GT2560/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Geeetech/GT2560/Configuration_adv.h +++ b/config/examples/Geeetech/GT2560/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index c400d5e68a..f9a44c2395 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration_adv.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration_adv.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index 1e46efeec1..2a146e7ebc 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 6adb55f0ff..1912063d5d 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 3cc1177755..ff405bbf27 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 26c462f8d0..5b23f004c6 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index 1a31219190..aa5df16e0e 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index 441fdd360d..0d46a5a5fd 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 9a68edfe11..9a6512f52b 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index 104f0c08d0..bf56bbdced 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index 9c6c83ec8f..ebb5778da8 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index 7a40d289c7..7954e18006 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 390e40b04f..bb3453b011 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index e1403719c2..476b3eafca 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 44309240e9..f5ba252dfb 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index fdbb7a37c2..07f092d822 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index b2d8884dd8..d4345cfd78 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index fdbb7a37c2..07f092d822 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 08388ac09c..434f9a07c5 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -949,7 +949,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index 7b7d2a9697..6e8dd245a2 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Hictop/3DP-17/Configuration.h b/config/examples/Hictop/3DP-17/Configuration.h index 7c017608f8..f76c16c23e 100644 --- a/config/examples/Hictop/3DP-17/Configuration.h +++ b/config/examples/Hictop/3DP-17/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Hictop/3DP-17/Configuration_adv.h b/config/examples/Hictop/3DP-17/Configuration_adv.h index 35ae3d8033..c4f7a3feba 100644 --- a/config/examples/Hictop/3DP-17/Configuration_adv.h +++ b/config/examples/Hictop/3DP-17/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index be9eb4bb4c..c214ba7fe7 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 632cd6dae9..f2369f6896 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h index db96c7d703..ef0b372bd2 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h b/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h index 036db12879..f01cbab611 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4303,7 +4303,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index ca8a863939..bfffd725bf 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index c055368de0..2969f9f329 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -303,7 +303,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -784,7 +784,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1180,7 +1180,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4312,7 +4312,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index 875b61ee72..01e85350ce 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/JGAurora/A3/Configuration_adv.h b/config/examples/JGAurora/A3/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/JGAurora/A3/Configuration_adv.h +++ b/config/examples/JGAurora/A3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 3559e806d7..9d5a95ef6f 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index c6e5843a17..0115c9c15e 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index c44a2dd756..16a3d253d7 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 6e5ab74a74..b617e9659d 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -303,7 +303,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -784,7 +784,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1180,7 +1180,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4312,7 +4312,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index c286d17514..e4a9dd1a1f 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 113c31decd..7dfa6b420c 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index 08c669bc69..a13a4fd2f7 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Kingroon/KP3/Configuration_adv.h b/config/examples/Kingroon/KP3/Configuration_adv.h index b997649e47..9b1db46327 100644 --- a/config/examples/Kingroon/KP3/Configuration_adv.h +++ b/config/examples/Kingroon/KP3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Kingroon/KP3S/Configuration.h b/config/examples/Kingroon/KP3S/Configuration.h index 88b76f345c..d5bf0aa733 100644 --- a/config/examples/Kingroon/KP3S/Configuration.h +++ b/config/examples/Kingroon/KP3S/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Kingroon/KP3S/Configuration_adv.h b/config/examples/Kingroon/KP3S/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Kingroon/KP3S/Configuration_adv.h +++ b/config/examples/Kingroon/KP3S/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Kingroon/KP3S_Pro/Configuration.h b/config/examples/Kingroon/KP3S_Pro/Configuration.h index 1c8c1340a9..24f1137f7e 100644 --- a/config/examples/Kingroon/KP3S_Pro/Configuration.h +++ b/config/examples/Kingroon/KP3S_Pro/Configuration.h @@ -972,7 +972,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Kingroon/KP3S_Pro/Configuration_adv.h b/config/examples/Kingroon/KP3S_Pro/Configuration_adv.h index 3f18b44d7d..90ad394749 100644 --- a/config/examples/Kingroon/KP3S_Pro/Configuration_adv.h +++ b/config/examples/Kingroon/KP3S_Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Kingroon/KP5L-DIY/Configuration.h b/config/examples/Kingroon/KP5L-DIY/Configuration.h index 1e3104a7d9..8fc318237a 100644 --- a/config/examples/Kingroon/KP5L-DIY/Configuration.h +++ b/config/examples/Kingroon/KP5L-DIY/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Kingroon/KP5L-DIY/Configuration_adv.h b/config/examples/Kingroon/KP5L-DIY/Configuration_adv.h index 70b7d1e9bd..ddf4dec9d3 100644 --- a/config/examples/Kingroon/KP5L-DIY/Configuration_adv.h +++ b/config/examples/Kingroon/KP5L-DIY/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Labists/ET4/Configuration.h b/config/examples/Labists/ET4/Configuration.h index 59ecf66034..d348220620 100644 --- a/config/examples/Labists/ET4/Configuration.h +++ b/config/examples/Labists/ET4/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Labists/ET4/Configuration_adv.h b/config/examples/Labists/ET4/Configuration_adv.h index f19c559c6f..5ae77c57ef 100644 --- a/config/examples/Labists/ET4/Configuration_adv.h +++ b/config/examples/Labists/ET4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Longer/LK5/Configuration.h b/config/examples/Longer/LK5/Configuration.h index 4ca4b1c668..74ab868f66 100644 --- a/config/examples/Longer/LK5/Configuration.h +++ b/config/examples/Longer/LK5/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Longer/LK5/Configuration_adv.h b/config/examples/Longer/LK5/Configuration_adv.h index 5f168059a8..dad805d770 100644 --- a/config/examples/Longer/LK5/Configuration_adv.h +++ b/config/examples/Longer/LK5/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/LulzBot/TAZ4/Configuration.h b/config/examples/LulzBot/TAZ4/Configuration.h index febf68f19f..6857fe89bc 100644 --- a/config/examples/LulzBot/TAZ4/Configuration.h +++ b/config/examples/LulzBot/TAZ4/Configuration.h @@ -962,7 +962,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/LulzBot/TAZ4/Configuration_adv.h b/config/examples/LulzBot/TAZ4/Configuration_adv.h index 7852ab161f..bbc280f2d7 100644 --- a/config/examples/LulzBot/TAZ4/Configuration_adv.h +++ b/config/examples/LulzBot/TAZ4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index c02c5c0812..0a6a710781 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MBot/Cube/Configuration_adv.h b/config/examples/MBot/Cube/Configuration_adv.h index 37dd5ab4e5..963a6c4a6e 100644 --- a/config/examples/MBot/Cube/Configuration_adv.h +++ b/config/examples/MBot/Cube/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MakerBot/Replicator Dual/Configuration.h b/config/examples/MakerBot/Replicator Dual/Configuration.h index 9723ee01e5..3f53903015 100644 --- a/config/examples/MakerBot/Replicator Dual/Configuration.h +++ b/config/examples/MakerBot/Replicator Dual/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MakerBot/Replicator Dual/Configuration_adv.h b/config/examples/MakerBot/Replicator Dual/Configuration_adv.h index 9dac0e303f..e4a13d6743 100644 --- a/config/examples/MakerBot/Replicator Dual/Configuration_adv.h +++ b/config/examples/MakerBot/Replicator Dual/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4285,7 +4285,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MakerBot/Replicator Single/Configuration.h b/config/examples/MakerBot/Replicator Single/Configuration.h index 74d8afeb60..f96c3a864d 100644 --- a/config/examples/MakerBot/Replicator Single/Configuration.h +++ b/config/examples/MakerBot/Replicator Single/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MakerBot/Replicator Single/Configuration_adv.h b/config/examples/MakerBot/Replicator Single/Configuration_adv.h index f5414a93c4..852aab04ed 100644 --- a/config/examples/MakerBot/Replicator Single/Configuration_adv.h +++ b/config/examples/MakerBot/Replicator Single/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4285,7 +4285,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h index 3d4b520b6d..0ed76987bf 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h index 0d715d7ee0..5567e8317d 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4301,7 +4301,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MakerGear/M2 Rev H/Configuration.h b/config/examples/MakerGear/M2 Rev H/Configuration.h index 88b4ea37e1..6cef50dd68 100644 --- a/config/examples/MakerGear/M2 Rev H/Configuration.h +++ b/config/examples/MakerGear/M2 Rev H/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MakerGear/M2 Rev H/Configuration_adv.h b/config/examples/MakerGear/M2 Rev H/Configuration_adv.h index 6b0317513b..898aa16d6a 100644 --- a/config/examples/MakerGear/M2 Rev H/Configuration_adv.h +++ b/config/examples/MakerGear/M2 Rev H/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4285,7 +4285,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 67925f4ad9..0f42c3e150 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 19af168fca..a12374a48b 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/MakerTech3D/Proforge2sDual/Configuration.h b/config/examples/MakerTech3D/Proforge2sDual/Configuration.h index 7792f792e5..32cf6b33fb 100644 --- a/config/examples/MakerTech3D/Proforge2sDual/Configuration.h +++ b/config/examples/MakerTech3D/Proforge2sDual/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/MakerTech3D/Proforge2sDual/Configuration_adv.h b/config/examples/MakerTech3D/Proforge2sDual/Configuration_adv.h index d319447815..676f4bd916 100644 --- a/config/examples/MakerTech3D/Proforge2sDual/Configuration_adv.h +++ b/config/examples/MakerTech3D/Proforge2sDual/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 796577eef0..e83a964e67 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -960,7 +960,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 6ad9a975d0..b72cbf6f42 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Malyan/M180/Configuration.h b/config/examples/Malyan/M180/Configuration.h index 77c6ad5df1..678680f392 100644 --- a/config/examples/Malyan/M180/Configuration.h +++ b/config/examples/Malyan/M180/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Malyan/M180/Configuration_adv.h b/config/examples/Malyan/M180/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Malyan/M180/Configuration_adv.h +++ b/config/examples/Malyan/M180/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index d317ff2d78..1f53c0777e 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 6cd632eca4..845ed8c2cb 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -780,7 +780,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Materia101/Configuration.h b/config/examples/Materia101/Configuration.h index f3fea80a2a..4e6f25e4e5 100644 --- a/config/examples/Materia101/Configuration.h +++ b/config/examples/Materia101/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Materia101/Configuration_adv.h b/config/examples/Materia101/Configuration_adv.h index 3dd3ef7ca8..444f21af4d 100644 --- a/config/examples/Materia101/Configuration_adv.h +++ b/config/examples/Materia101/Configuration_adv.h @@ -295,7 +295,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -776,7 +776,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1172,7 +1172,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index eecb2c33d8..3baf6dbb81 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Micromake/C1/basic/Configuration_adv.h b/config/examples/Micromake/C1/basic/Configuration_adv.h index 773f005816..8beffb9ec8 100644 --- a/config/examples/Micromake/C1/basic/Configuration_adv.h +++ b/config/examples/Micromake/C1/basic/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index f0a349850e..cc3c842352 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 7ae0732871..55d0666d4f 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 8c24fa6e0b..55cd1a9d1b 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index d1ff10a7bb..9ae6d3a7de 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -959,7 +959,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Mks/Robin_Lite3/Configuration_adv.h b/config/examples/Mks/Robin_Lite3/Configuration_adv.h index e7b0b9093e..b0b38702ba 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration_adv.h +++ b/config/examples/Mks/Robin_Lite3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index 136551b892..995df669c4 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Mks/Robin_Pro/Configuration_adv.h b/config/examples/Mks/Robin_Pro/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Mks/Robin_Pro/Configuration_adv.h +++ b/config/examples/Mks/Robin_Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index c7c14aad0a..a6b5e2fd21 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 08f8acf1f6..fdda6cd54c 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index d685fad99d..7a4c35c3b5 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 13c8b1ea32..6324d71a35 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Nextion/Configuration.h b/config/examples/Nextion/Configuration.h index ef0f95715e..450fbdd4f5 100644 --- a/config/examples/Nextion/Configuration.h +++ b/config/examples/Nextion/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Nextion/Configuration_adv.h b/config/examples/Nextion/Configuration_adv.h index 5694177939..3ec2863e3c 100644 --- a/config/examples/Nextion/Configuration_adv.h +++ b/config/examples/Nextion/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration.h b/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration.h index a5906900d8..fe64a306e0 100644 --- a/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration.h +++ b/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration_adv.h b/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration_adv.h index 97c6676689..1fc216fa43 100644 --- a/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration_adv.h +++ b/config/examples/ORD Bot/Hadron/Sanguinololu/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Opulo/Lumen_REV3/Configuration.h b/config/examples/Opulo/Lumen_REV3/Configuration.h index bff84bc0d6..83d6d01db0 100644 --- a/config/examples/Opulo/Lumen_REV3/Configuration.h +++ b/config/examples/Opulo/Lumen_REV3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Opulo/Lumen_REV3/Configuration_adv.h b/config/examples/Opulo/Lumen_REV3/Configuration_adv.h index e8c784dfcd..6bedad9454 100644 --- a/config/examples/Opulo/Lumen_REV3/Configuration_adv.h +++ b/config/examples/Opulo/Lumen_REV3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Opulo/Lumen_REV4/Configuration.h b/config/examples/Opulo/Lumen_REV4/Configuration.h index d423254000..3d5da62710 100644 --- a/config/examples/Opulo/Lumen_REV4/Configuration.h +++ b/config/examples/Opulo/Lumen_REV4/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Opulo/Lumen_REV4/Configuration_adv.h b/config/examples/Opulo/Lumen_REV4/Configuration_adv.h index 29e3b54b91..6030522c6a 100644 --- a/config/examples/Opulo/Lumen_REV4/Configuration_adv.h +++ b/config/examples/Opulo/Lumen_REV4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1173,7 +1173,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Opulo/Lumen_REV5/Configuration.h b/config/examples/Opulo/Lumen_REV5/Configuration.h index a81fae3e1e..6bd48b52c0 100644 --- a/config/examples/Opulo/Lumen_REV5/Configuration.h +++ b/config/examples/Opulo/Lumen_REV5/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Opulo/Lumen_REV5/Configuration_adv.h b/config/examples/Opulo/Lumen_REV5/Configuration_adv.h index b8ac8297f3..ad5457941b 100644 --- a/config/examples/Opulo/Lumen_REV5/Configuration_adv.h +++ b/config/examples/Opulo/Lumen_REV5/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1173,7 +1173,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index 52dcefd89c..8f975c0ea6 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Ortur 4/Configuration_adv.h b/config/examples/Ortur 4/Configuration_adv.h index b2bd71faf1..a7c7aaaeb9 100644 --- a/config/examples/Ortur 4/Configuration_adv.h +++ b/config/examples/Ortur 4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Polargraph/Configuration.h b/config/examples/Polargraph/Configuration.h index 146657bbd3..ed895d5864 100644 --- a/config/examples/Polargraph/Configuration.h +++ b/config/examples/Polargraph/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Polargraph/Configuration_adv.h b/config/examples/Polargraph/Configuration_adv.h index 08b53f69f4..2187bc8359 100644 --- a/config/examples/Polargraph/Configuration_adv.h +++ b/config/examples/Polargraph/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index 158c7df5d6..d5e5428a20 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration_adv.h b/config/examples/Printrbot/PrintrboardG2/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration_adv.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index a4eaf215b0..032ec8f8dc 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration_adv.h b/config/examples/Printrbot/Simple Metal RevD/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration_adv.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Printrbot/Simple_Metal_RevF6/Configuration.h b/config/examples/Printrbot/Simple_Metal_RevF6/Configuration.h index ac4523c678..88238c3faf 100644 --- a/config/examples/Printrbot/Simple_Metal_RevF6/Configuration.h +++ b/config/examples/Printrbot/Simple_Metal_RevF6/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Printrbot/Simple_Metal_RevF6/Configuration_adv.h b/config/examples/Printrbot/Simple_Metal_RevF6/Configuration_adv.h index 9de4c7551a..c7322ff021 100644 --- a/config/examples/Printrbot/Simple_Metal_RevF6/Configuration_adv.h +++ b/config/examples/Printrbot/Simple_Metal_RevF6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Prusa/MK3/Configuration.h b/config/examples/Prusa/MK3/Configuration.h index 8653806591..1c14086381 100644 --- a/config/examples/Prusa/MK3/Configuration.h +++ b/config/examples/Prusa/MK3/Configuration.h @@ -977,7 +977,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Prusa/MK3/Configuration_adv.h b/config/examples/Prusa/MK3/Configuration_adv.h index 32d1e2d5cc..55e6182cb8 100644 --- a/config/examples/Prusa/MK3/Configuration_adv.h +++ b/config/examples/Prusa/MK3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4310,7 +4310,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index c2a4d5d5be..c53f852bec 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -967,7 +967,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h index 31a62c9453..b1c0c9b202 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4311,7 +4311,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index 00a04f3a15..cba8c43c10 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Qidi/Qidi 1/Configuration_adv.h b/config/examples/Qidi/Qidi 1/Configuration_adv.h index ebf2faf70d..67a65a8dbc 100644 --- a/config/examples/Qidi/Qidi 1/Configuration_adv.h +++ b/config/examples/Qidi/Qidi 1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h index d5c2e4c386..03cf6a1e05 100644 --- a/config/examples/Raiscube/A8r/Configuration.h +++ b/config/examples/Raiscube/A8r/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Raiscube/A8r/Configuration_adv.h b/config/examples/Raiscube/A8r/Configuration_adv.h index 56a881a553..ce93848ad4 100644 --- a/config/examples/Raiscube/A8r/Configuration_adv.h +++ b/config/examples/Raiscube/A8r/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 3854414425..25e6e283e7 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 441fdd360d..0d46a5a5fd 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index 7f51888386..03bf505190 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 7043467bca..34182c61db 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index b233de4d1c..340b5e6735 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index 7043467bca..34182c61db 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 890db26166..867268732d 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index 7043467bca..34182c61db 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 7c58b20898..650a5546a3 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/RepRapPro/Huxley/Configuration_adv.h b/config/examples/RepRapPro/Huxley/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/RepRapPro/Huxley/Configuration_adv.h +++ b/config/examples/RepRapPro/Huxley/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 9401cc7be3..8efe06defd 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/RepRapWorld/Megatronics/Configuration_adv.h b/config/examples/RepRapWorld/Megatronics/Configuration_adv.h index 7f1d300f54..97514dfe97 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration_adv.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/RepRapWorld/Minitronics11/Configuration.h b/config/examples/RepRapWorld/Minitronics11/Configuration.h index c24365c42a..2137f285ca 100644 --- a/config/examples/RepRapWorld/Minitronics11/Configuration.h +++ b/config/examples/RepRapWorld/Minitronics11/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/RepRapWorld/Minitronics11/Configuration_adv.h b/config/examples/RepRapWorld/Minitronics11/Configuration_adv.h index abd77540c0..f6c18ccb55 100644 --- a/config/examples/RepRapWorld/Minitronics11/Configuration_adv.h +++ b/config/examples/RepRapWorld/Minitronics11/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/RepRapWorld/Minitronics20/CNC/Configuration.h b/config/examples/RepRapWorld/Minitronics20/CNC/Configuration.h index 4fbf864bd1..7e8ab60c47 100644 --- a/config/examples/RepRapWorld/Minitronics20/CNC/Configuration.h +++ b/config/examples/RepRapWorld/Minitronics20/CNC/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/RepRapWorld/Minitronics20/CNC/Configuration_adv.h b/config/examples/RepRapWorld/Minitronics20/CNC/Configuration_adv.h index e859ad9f7b..d7a2abe9bc 100644 --- a/config/examples/RepRapWorld/Minitronics20/CNC/Configuration_adv.h +++ b/config/examples/RepRapWorld/Minitronics20/CNC/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. #define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 584ecd5de5..3d93756207 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -963,7 +963,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 94ea8a2865..63531f2548 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index 3ad2aa86d7..84223ce167 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Robo3D/R1+/Configuration_adv.h b/config/examples/Robo3D/R1+/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Robo3D/R1+/Configuration_adv.h +++ b/config/examples/Robo3D/R1+/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Rolohaun/Rook MK1/Configuration.h b/config/examples/Rolohaun/Rook MK1/Configuration.h index cde98668b3..8745c0cf1b 100644 --- a/config/examples/Rolohaun/Rook MK1/Configuration.h +++ b/config/examples/Rolohaun/Rook MK1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Rolohaun/Rook MK1/Configuration_adv.h b/config/examples/Rolohaun/Rook MK1/Configuration_adv.h index 92491bede4..9ab9729097 100644 --- a/config/examples/Rolohaun/Rook MK1/Configuration_adv.h +++ b/config/examples/Rolohaun/Rook MK1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 17e4b8cef5..dac68b46e2 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index 184beddcc4..33156f15b6 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 3e9e0ff2bc..62d8df9479 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index f596b64ce0..71c00a8424 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index ce55402a3b..343921547a 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 2497c059d4..2829a2ee3a 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index daf0af6094..32a8698d6d 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/STM32/STM32F103RE/Configuration_adv.h b/config/examples/STM32/STM32F103RE/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/STM32/STM32F103RE/Configuration_adv.h +++ b/config/examples/STM32/STM32F103RE/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Simax/Mi-M200/Configuration.h b/config/examples/Simax/Mi-M200/Configuration.h index 99dc77abe9..c8de7ca49a 100644 --- a/config/examples/Simax/Mi-M200/Configuration.h +++ b/config/examples/Simax/Mi-M200/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Simax/Mi-M200/Configuration_adv.h b/config/examples/Simax/Mi-M200/Configuration_adv.h index d6097f5f0d..e51a53a39c 100644 --- a/config/examples/Simax/Mi-M200/Configuration_adv.h +++ b/config/examples/Simax/Mi-M200/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Simulator/Configuration.h b/config/examples/Simulator/Configuration.h index 8b271d361b..37bbc6e9e9 100644 --- a/config/examples/Simulator/Configuration.h +++ b/config/examples/Simulator/Configuration.h @@ -966,7 +966,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Simulator/Configuration_adv.h b/config/examples/Simulator/Configuration_adv.h index 4305585582..b24b162f0f 100644 --- a/config/examples/Simulator/Configuration_adv.h +++ b/config/examples/Simulator/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h index 43c66e6ffe..f732c77fe3 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h index f186f82c60..92b431aeb7 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h index 8b664691ef..836234d3e2 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index edc9b72103..0f9e563abb 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration.h index 63975b0afe..a034701f62 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h index 39b62e926c..147df47d33 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h index f184158a63..bfa7c27004 100644 --- a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h index f6ea6eb2b8..f9b0945580 100644 --- a/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h index 56f64aa758..895d2dba75 100644 --- a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h index 8ca19888eb..b03ad7e715 100644 --- a/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-02/Configuration.h b/config/examples/Sovol/SV-02/Configuration.h index bf74c925b4..038e11966b 100644 --- a/config/examples/Sovol/SV-02/Configuration.h +++ b/config/examples/Sovol/SV-02/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-02/Configuration_adv.h b/config/examples/Sovol/SV-02/Configuration_adv.h index 3647f1b013..83877ee83e 100644 --- a/config/examples/Sovol/SV-02/Configuration_adv.h +++ b/config/examples/Sovol/SV-02/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-03/Configuration.h b/config/examples/Sovol/SV-03/Configuration.h index 6eaac31fc1..fd1615748f 100644 --- a/config/examples/Sovol/SV-03/Configuration.h +++ b/config/examples/Sovol/SV-03/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-03/Configuration_adv.h b/config/examples/Sovol/SV-03/Configuration_adv.h index 9dab738bfc..bf6eeae7f9 100644 --- a/config/examples/Sovol/SV-03/Configuration_adv.h +++ b/config/examples/Sovol/SV-03/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-05/Configuration.h b/config/examples/Sovol/SV-05/Configuration.h index 67d3dcc43c..2154a45930 100644 --- a/config/examples/Sovol/SV-05/Configuration.h +++ b/config/examples/Sovol/SV-05/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-05/Configuration_adv.h b/config/examples/Sovol/SV-05/Configuration_adv.h index 8de96213c9..e106266ca5 100644 --- a/config/examples/Sovol/SV-05/Configuration_adv.h +++ b/config/examples/Sovol/SV-05/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-06 Plus/Configuration.h b/config/examples/Sovol/SV-06 Plus/Configuration.h index 38aedb8e51..ab829955a6 100644 --- a/config/examples/Sovol/SV-06 Plus/Configuration.h +++ b/config/examples/Sovol/SV-06 Plus/Configuration.h @@ -955,7 +955,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-06 Plus/Configuration_adv.h b/config/examples/Sovol/SV-06 Plus/Configuration_adv.h index c6260f96a7..851bd5b9d9 100644 --- a/config/examples/Sovol/SV-06 Plus/Configuration_adv.h +++ b/config/examples/Sovol/SV-06 Plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sovol/SV-06/Configuration.h b/config/examples/Sovol/SV-06/Configuration.h index 0592adcffe..810726f629 100644 --- a/config/examples/Sovol/SV-06/Configuration.h +++ b/config/examples/Sovol/SV-06/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sovol/SV-06/Configuration_adv.h b/config/examples/Sovol/SV-06/Configuration_adv.h index f369ca94a8..8d09dddf99 100644 --- a/config/examples/Sovol/SV-06/Configuration_adv.h +++ b/config/examples/Sovol/SV-06/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sunlu/S8/Configuration.h b/config/examples/Sunlu/S8/Configuration.h index d9c79aa882..2b4550fe9d 100644 --- a/config/examples/Sunlu/S8/Configuration.h +++ b/config/examples/Sunlu/S8/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sunlu/S8/Configuration_adv.h b/config/examples/Sunlu/S8/Configuration_adv.h index e076dd4fc0..0e96d261b2 100644 --- a/config/examples/Sunlu/S8/Configuration_adv.h +++ b/config/examples/Sunlu/S8/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Sunlu/T3/Configuration.h b/config/examples/Sunlu/T3/Configuration.h index 888aa329d7..7ebd9c620f 100644 --- a/config/examples/Sunlu/T3/Configuration.h +++ b/config/examples/Sunlu/T3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Sunlu/T3/Configuration_adv.h b/config/examples/Sunlu/T3/Configuration_adv.h index 470656b2a9..ef76981dc7 100644 --- a/config/examples/Sunlu/T3/Configuration_adv.h +++ b/config/examples/Sunlu/T3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration.h b/config/examples/TPARA/AXEL_TPARA/Configuration.h index 79711eaffd..60ac33acd1 100644 --- a/config/examples/TPARA/AXEL_TPARA/Configuration.h +++ b/config/examples/TPARA/AXEL_TPARA/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h b/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h index be1f69df16..f88ac897cf 100644 --- a/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h +++ b/config/examples/TPARA/AXEL_TPARA/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index 954b793d71..9452ffd8d8 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index b46893122e..f93bd0d19c 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 07f90c7d62..38f39e2dcb 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index 3f5e820796..910ab86cc4 100644 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration.h b/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration.h index 9cdf162ac7..fdb18e4e7e 100644 --- a/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration_adv.h index 0ba9fa67e6..996f24d6cb 100644 --- a/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/MKS Gen_L/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration.h b/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration.h index dbc76600e1..5d31706a32 100644 --- a/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration_adv.h index 1bf4c18c89..4b4e8b9025 100644 --- a/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/MKS SGen_L/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 31eef66188..62cdc7444e 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 02dde27836..46c84fed62 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration.h index 8add32f221..6bc3847e97 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration_adv.h index 02dde27836..46c84fed62 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS Gen_L)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration.h b/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration.h index 3c932510fd..58754b4584 100644 --- a/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration.h +++ b/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration_adv.h b/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration_adv.h index fa4cccb837..f105625afe 100644 --- a/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration_adv.h +++ b/config/examples/Tinkerine/Ditto Pro/RAMPS 1.4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 576bdb77e8..c45a55bb11 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -991,7 +991,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index ec4a4e65e0..ecd14dda41 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration.h b/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration.h index ec54422b39..45d62c8d8a 100644 --- a/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration.h +++ b/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration_adv.h b/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration_adv.h index 318ba5967d..b7fb9cd349 100644 --- a/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration_adv.h +++ b/config/examples/Tronxy/D01/CXY-v6-191017 board/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 4c315abad7..35ee7c0869 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X1/Configuration_adv.h b/config/examples/Tronxy/X1/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Tronxy/X1/Configuration_adv.h +++ b/config/examples/Tronxy/X1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 566eb91351..8532f5732f 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index eea866d084..e3e9be1d59 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration.h b/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration.h index b44255a034..348858dbec 100644 --- a/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration_adv.h index 0e3e2f461f..9344b59c56 100644 --- a/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Green Board (Chitu V5)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration.h b/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration.h index 6e7b4618f2..2f7822851f 100644 --- a/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration.h @@ -960,7 +960,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration_adv.h index d96c7ab247..b8b7367229 100644 --- a/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Red Board (Tronxy 3.1.0)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 4c6ccfdc91..0be804b10b 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X5S/Configuration_adv.h b/config/examples/Tronxy/X5S/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Tronxy/X5S/Configuration_adv.h +++ b/config/examples/Tronxy/X5S/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X5SA-2E/Configuration.h b/config/examples/Tronxy/X5SA-2E/Configuration.h index b8e4c3e6cf..4420dde5f4 100644 --- a/config/examples/Tronxy/X5SA-2E/Configuration.h +++ b/config/examples/Tronxy/X5SA-2E/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X5SA-2E/Configuration_adv.h b/config/examples/Tronxy/X5SA-2E/Configuration_adv.h index e0ceedc5b9..545a88b1a6 100644 --- a/config/examples/Tronxy/X5SA-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA-2E/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4310,7 +4310,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index d02fcfda46..66232e123d 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/X5SA/Configuration_adv.h b/config/examples/Tronxy/X5SA/Configuration_adv.h index d2c3a0c634..73c1e47818 100644 --- a/config/examples/Tronxy/X5SA/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4310,7 +4310,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 0a7aa9de6d..5d7b840cca 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/XY100/Configuration_adv.h b/config/examples/Tronxy/XY100/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Tronxy/XY100/Configuration_adv.h +++ b/config/examples/Tronxy/XY100/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Tronxy/XY2-Pro/Configuration.h b/config/examples/Tronxy/XY2-Pro/Configuration.h index 9cff2b0c9b..50ea63d698 100644 --- a/config/examples/Tronxy/XY2-Pro/Configuration.h +++ b/config/examples/Tronxy/XY2-Pro/Configuration.h @@ -987,7 +987,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Tronxy/XY2-Pro/Configuration_adv.h b/config/examples/Tronxy/XY2-Pro/Configuration_adv.h index 69d51bc760..7e8ac52b27 100644 --- a/config/examples/Tronxy/XY2-Pro/Configuration_adv.h +++ b/config/examples/Tronxy/XY2-Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Turnigy/Fabrikator/Configuration.h b/config/examples/Turnigy/Fabrikator/Configuration.h index 6c47a7654f..86264a42ea 100644 --- a/config/examples/Turnigy/Fabrikator/Configuration.h +++ b/config/examples/Turnigy/Fabrikator/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Turnigy/Fabrikator/Configuration_adv.h b/config/examples/Turnigy/Fabrikator/Configuration_adv.h index 980e8babfc..41a2b1b6f3 100644 --- a/config/examples/Turnigy/Fabrikator/Configuration_adv.h +++ b/config/examples/Turnigy/Fabrikator/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/BlueR Plus/Configuration.h b/config/examples/Two Trees/BlueR Plus/Configuration.h index 09d17671cf..516abe62c1 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/BlueR Plus/Configuration_adv.h b/config/examples/Two Trees/BlueR Plus/Configuration_adv.h index 1751c25c5e..e3bb8e953b 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h index 1111800af2..cc07d4520d 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h @@ -966,7 +966,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h index e8353cdab2..277def1ba6 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h index 767fcfb9ce..46a52e1c02 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h @@ -967,7 +967,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h index e8353cdab2..277def1ba6 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h index bfc82082f7..37b5e41857 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h @@ -974,7 +974,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h index e8353cdab2..277def1ba6 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/SP-5_V3/Configuration.h b/config/examples/Two Trees/SP-5_V3/Configuration.h index 16bf3834c2..2e66a1cb30 100644 --- a/config/examples/Two Trees/SP-5_V3/Configuration.h +++ b/config/examples/Two Trees/SP-5_V3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/SP-5_V3/Configuration_adv.h b/config/examples/Two Trees/SP-5_V3/Configuration_adv.h index 9ee763ea73..41449d5e17 100644 --- a/config/examples/Two Trees/SP-5_V3/Configuration_adv.h +++ b/config/examples/Two Trees/SP-5_V3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration.h index c8c3d5eeb0..c27fdab556 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration_adv.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration_adv.h index 7d32ddefba..0ff5f35e5e 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. #define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1180,7 +1180,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4313,7 +4313,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h index 070d9f2053..46435023dd 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h index 007cb28493..fb168f7acc 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1180,7 +1180,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4313,7 +4313,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h index 5b8036a425..91c96cd9c6 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h @@ -964,7 +964,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h b/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h index 97fa8bac3d..0c0519b427 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 94df74c308..f11b4aea62 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index 1c84ac6d01..2fd9fee784 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index 40a0fb822d..4be9838e0f 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index af6fafe78d..da1a841690 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Ultimaker/Ultimaker 2+/Configuration.h b/config/examples/Ultimaker/Ultimaker 2+/Configuration.h index aa1daea811..5c9e34fa96 100644 --- a/config/examples/Ultimaker/Ultimaker 2+/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker 2+/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Ultimaker/Ultimaker 2+/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker 2+/Configuration_adv.h index 219bc9cbc2..6351f6ff04 100644 --- a/config/examples/Ultimaker/Ultimaker 2+/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker 2+/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Ultimaker/Ultimaker 2/Configuration.h b/config/examples/Ultimaker/Ultimaker 2/Configuration.h index 7c2282ce5b..70fb114705 100644 --- a/config/examples/Ultimaker/Ultimaker 2/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker 2/Configuration.h @@ -963,7 +963,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h index 4a62ca69aa..500fa6e064 100644 --- a/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker 2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h index 5f9d628a57..eb6e8c9085 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h index 8020cd44bb..88a6abff08 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h index fa9d0259c2..e73e6bf74f 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h index 322826c9e0..38f44e9940 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration.h b/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration.h index 242f760e7c..47af2e5476 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration_adv.h index 4efc99fa97..c7c4fae9c5 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus DXU/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1172,7 +1172,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 81abd811ce..ed20bc68e4 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 2e16a6258e..64c9e73d24 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Velleman/K8200 Upgraded/Configuration.h b/config/examples/Velleman/K8200 Upgraded/Configuration.h index cebd899760..58c4ade5b4 100644 --- a/config/examples/Velleman/K8200 Upgraded/Configuration.h +++ b/config/examples/Velleman/K8200 Upgraded/Configuration.h @@ -978,7 +978,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Velleman/K8200 Upgraded/Configuration_adv.h b/config/examples/Velleman/K8200 Upgraded/Configuration_adv.h index 8fe38d8c2b..423d8c341c 100644 --- a/config/examples/Velleman/K8200 Upgraded/Configuration_adv.h +++ b/config/examples/Velleman/K8200 Upgraded/Configuration_adv.h @@ -306,7 +306,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -791,7 +791,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1187,7 +1187,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4317,7 +4317,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index cea50418be..42676bfbc1 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -980,7 +980,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index 223f663bc2..c0e8ee43a6 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -306,7 +306,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -791,7 +791,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1187,7 +1187,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4319,7 +4319,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 92798a5cf1..d494b754b2 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index b00793bef4..dc7fc8ef97 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index d6614f88b0..3860d1349a 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index b00793bef4..dc7fc8ef97 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration.h index 7e99ba240f..4e40de6b45 100644 --- a/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 558b8f5e81..4fa5424222 100644 --- a/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Voxelab/Aquila/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index da8099cc57..6cf734e134 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -965,7 +965,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 4f04c0a305..ff9c8ec1a4 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index e0b0eb9833..b5a8d26191 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h index 01f7ab7f05..69eee26203 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 6d472afa41..0298efc53c 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 263f606df6..5171a5dabb 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration.h index ea95a309ba..10f2bd3134 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration_adv.h index d141a18017..67b0b59e2d 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK1/300/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration.h index c568be4326..268519badf 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration_adv.h index d141a18017..67b0b59e2d 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK1/400/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration.h index 8ab83cafe3..9b14ec0371 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK1/500/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration.h index 990dcd01d6..5b83234d2b 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK1u2/300/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration.h index 7906646705..a3b746fa5e 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK1u2/400/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration.h index 0b6ab1aa8f..3bc5650576 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK1u2/500/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration.h index 78e8ec5700..1d27228aab 100644 --- a/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK2/300/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration.h index d8cbb4897d..a4de9988ba 100644 --- a/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK2/400/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration.h index f5c3a37849..26c7b3ae00 100644 --- a/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK2/500/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration.h index fffad62ba6..1abae780ab 100644 --- a/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK3/300/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration.h index b6539a0216..0d5332da94 100644 --- a/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK3/400/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration.h b/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration.h index 761143aad9..9965082718 100644 --- a/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration.h +++ b/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration_adv.h b/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration_adv.h index 8d5d945b12..953b59000f 100644 --- a/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 9/MK3/500/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4286,7 +4286,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 8612fccdbf..60a70e28f9 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index 79230f5fcd..c16744fbb7 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 9dcbdc2e56..65d85c7068 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index ef9237c4e0..203d4eabaa 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h index a5b7bcdd2a..9112ddc30f 100644 --- a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Wanhao/Duplicator i3 Plus/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Plus/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/Wanhao/Duplicator i3 Plus/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Weedo/Tina2/V2/Configuration.h b/config/examples/Weedo/Tina2/V2/Configuration.h index 937b7cb30e..d674b3197a 100644 --- a/config/examples/Weedo/Tina2/V2/Configuration.h +++ b/config/examples/Weedo/Tina2/V2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Weedo/Tina2/V2/Configuration_adv.h b/config/examples/Weedo/Tina2/V2/Configuration_adv.h index 474f81cc84..c7dfdf088c 100644 --- a/config/examples/Weedo/Tina2/V2/Configuration_adv.h +++ b/config/examples/Weedo/Tina2/V2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Weedo/Tina2/V3/Configuration.h b/config/examples/Weedo/Tina2/V3/Configuration.h index 40e43e1c03..5102296717 100644 --- a/config/examples/Weedo/Tina2/V3/Configuration.h +++ b/config/examples/Weedo/Tina2/V3/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Weedo/Tina2/V3/Configuration_adv.h b/config/examples/Weedo/Tina2/V3/Configuration_adv.h index 474f81cc84..c7dfdf088c 100644 --- a/config/examples/Weedo/Tina2/V3/Configuration_adv.h +++ b/config/examples/Weedo/Tina2/V3/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index e475a1a477..d375ef0e06 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Weistek/wt150/Configuration_adv.h b/config/examples/Weistek/wt150/Configuration_adv.h index 659f7f2a7d..5fe70691fc 100644 --- a/config/examples/Weistek/wt150/Configuration_adv.h +++ b/config/examples/Weistek/wt150/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index 70e694cb16..84506101c8 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Zonestar/P802M/Configuration_adv.h b/config/examples/Zonestar/P802M/Configuration_adv.h index 05fcc788dc..018bed6263 100644 --- a/config/examples/Zonestar/P802M/Configuration_adv.h +++ b/config/examples/Zonestar/P802M/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index 5081ad04de..ad08cffe02 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h index 83329d520a..b48ae47a77 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index 90df48c1d7..cf951f70eb 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -953,7 +953,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h index 4f62b96de5..9ce322c518 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index a06d0a7bcb..87b0a73a7e 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -981,7 +981,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h index dda992c39a..a84ac2b801 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 4bf7290630..b92979961e 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -980,7 +980,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 328896790a..04c7afcd25 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index 8df63effe7..632c993123 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Anycubic/Predator/Configuration_adv.h b/config/examples/delta/Anycubic/Predator/Configuration_adv.h index ef6e58d5cd..9095feee7d 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Predator/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4309,7 +4309,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 811c64fab4..74dbeef03f 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index 8a078d3734..cdd38b49c5 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index 526dad2371..62b2455e31 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 8a078d3734..cdd38b49c5 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h index ee9308c3a6..a013c44b73 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h index 5b0ab72292..68a3dda532 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4305,7 +4305,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h index e68ad60f17..21777103e3 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h @@ -950,7 +950,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration_adv.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration_adv.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index a34b344012..3f6799ab44 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index 6bf0e335f0..30df9a4f29 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h index de316ecb4f..8cdff06c97 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h index e18c338c68..2121db50c1 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index f40f0a601b..55c164584a 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index c2f7a7e908..41bef87283 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index ed4de36769..ea97276c03 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index c2f7a7e908..41bef87283 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index e07072710e..90f651a2a7 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index f797719d87..93c1e4927a 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index 84d1fbf3a3..ebaf0eb071 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index 9ad26de0ce..0c55b4977d 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index 4102de2844..ae7d4d8779 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index 9ad26de0ce..0c55b4977d 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index 9cdf2fc68f..5c73c6281f 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index 9ad26de0ce..0c55b4977d 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index ada561c661..93eb8bdec6 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index 9ad26de0ce..0c55b4977d 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4304,7 +4304,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 6bb8743a7b..65a185327a 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index f78feb9a9e..1454a292ef 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index 57f697f862..e0f5f6d611 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h index 32a75ed2ea..41b58c3fc5 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index dec6f31f23..c811220819 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 84638b0888..d7add73361 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index 27e7e32535..87b0775562 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Malyan M300/Configuration_adv.h b/config/examples/delta/Malyan M300/Configuration_adv.h index e446572d0b..da231c220b 100644 --- a/config/examples/delta/Malyan M300/Configuration_adv.h +++ b/config/examples/delta/Malyan M300/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration.h b/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration.h index d7d9011908..096c2a750c 100644 --- a/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration.h +++ b/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration_adv.h b/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration_adv.h index 3c113bef1a..fd2e60e251 100644 --- a/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration_adv.h +++ b/config/examples/delta/Micromake-D1/MKS-Gen-L-V2.1/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -780,7 +780,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1176,7 +1176,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4287,7 +4287,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration.h b/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration.h index 7e01cbfa76..c8a7aef3fe 100644 --- a/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration.h +++ b/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration_adv.h b/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration_adv.h index 5530e5abb5..4f66b7a96d 100644 --- a/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration_adv.h +++ b/config/examples/delta/Micromake-D1/RAMPS-1.4/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4285,7 +4285,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index e6a4494fff..f771485c5e 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 25ae2f8b8f..0f4993ccbc 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/Velleman/K8800/Configuration.h b/config/examples/delta/Velleman/K8800/Configuration.h index 8290bc17ae..46e0132822 100644 --- a/config/examples/delta/Velleman/K8800/Configuration.h +++ b/config/examples/delta/Velleman/K8800/Configuration.h @@ -963,7 +963,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/Velleman/K8800/Configuration_adv.h b/config/examples/delta/Velleman/K8800/Configuration_adv.h index 50743bdc9c..b018da1288 100644 --- a/config/examples/delta/Velleman/K8800/Configuration_adv.h +++ b/config/examples/delta/Velleman/K8800/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4311,7 +4311,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 8733add492..c8d4945c58 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index f797719d87..93c1e4927a 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index 92b1782f4c..12bbd900b1 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 591c35e6f0..92cc5c8af5 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4308,7 +4308,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index cd8dbe12c9..ffa46ef559 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -951,7 +951,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index 77d506f4ea..0d3596b25d 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -956,7 +956,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/kossel_pro/Configuration_adv.h b/config/examples/delta/kossel_pro/Configuration_adv.h index 9c9ef7b3c6..7303ba3161 100644 --- a/config/examples/delta/kossel_pro/Configuration_adv.h +++ b/config/examples/delta/kossel_pro/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index b3d32ad76a..119a012bc2 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -957,7 +957,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 1550b8b0b0..b5cf0793d7 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4307,7 +4307,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index b0f31e31c0..7225a97e7d 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -958,7 +958,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 26aac987e2..05a74fdf77 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration.h b/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration.h index 6d968341b0..0d1eabbb3b 100644 --- a/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration.h +++ b/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration.h @@ -963,7 +963,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration_adv.h b/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration_adv.h index dfd8e10c32..c557421786 100644 --- a/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration_adv.h +++ b/config/examples/linear_axes/Octopus 8 LINEAR_AXES/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h index 3e3f8575c9..67b1941210 100644 --- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h +++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h @@ -938,7 +938,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h index bfebc1fe1b..e64b9d3ef5 100644 --- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h +++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 08a5f97916..47b54a0dc5 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -954,7 +954,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 9ee695f0d0..2a8f0e95b5 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index b40e772ac5..a0f97bae63 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -952,7 +952,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * If you get "Thermal Runaway" or "Heating failed" errors the diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 7149248a63..54a192468e 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -297,7 +297,7 @@ * protect against a broken or disconnected thermistor wire. * * The issue: If a thermistor falls out, it will report the much lower - * temperature of the air in the room, and the the firmware will keep + * temperature of the air in the room, and the firmware will keep * the heater on. * * The solution: Once the temperature reaches the target, start observing. @@ -778,7 +778,7 @@ // @section endstops -// If you want endstops to stay on (by default) even when not homing +// If you want endstops to stay on (by default) even when not homing, // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT @@ -1174,7 +1174,7 @@ #define FTM_SHAPING_V_TOL_Z 0.05f // Vibration tolerance used by EI input shapers for Z axis //#define FTM_SHAPER_E // Include E shaping support - // Required to synchronise extruder with XYZ (better quality) + // Required to synchronize extruder with XYZ (better quality) #define FTM_DEFAULT_SHAPER_E ftMotionShaper_NONE // Default shaper mode on Extruder axis #define FTM_SHAPING_DEFAULT_FREQ_E 21.0f // (Hz) Default peak frequency used by input shapers #define FTM_SHAPING_ZETA_E 0.03f // Zeta used by input shapers for E axis @@ -4306,7 +4306,7 @@ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper // steps per full revolution (motor steps/rev * microstepping) //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. - #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error correction. #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the // printer will attempt to correct the error; errors // smaller than this are ignored to minimize effects of