✨ EVENT_GCODE_AFTER_HOMING

MarlinFirmware/Marlin#26469

config/default/Configuration.h

@@ -1781,6 +1781,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -1851,6 +1851,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Alfawise/U20/Configuration.h

@@ -1852,6 +1852,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AliExpress/CL-260/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/A2/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/A2plus/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/A6/Configuration.h

@@ -1822,6 +1822,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/A8/Configuration.h

@@ -1785,6 +1785,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/A8plus/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/A9/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/E10/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/E16/BTT SKR 1.3/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/E16/Stock/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET4+/Configuration.h

@@ -1788,6 +1788,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET4-Pro/Configuration.h

@@ -1788,6 +1788,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET4/Configuration.h

@@ -1788,6 +1788,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET4X/Configuration.h

@@ -1788,6 +1788,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET5-Pro/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET5/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Anet/ET5X/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/Chiron/Configuration.h

@@ -1785,6 +1785,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/Vyper/Configuration.h

@@ -1782,6 +1782,8 @@
 #define Z_AFTER_HOMING            2   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h

@@ -1838,6 +1838,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h

@@ -1798,6 +1798,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/AnyCubic/i3/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/ArmEd/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Artillery/Genius Pro/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Artillery/Genius/BLTouch/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Artillery/Genius/V1/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Artillery/Hornet/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR 1

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h

@@ -1798,6 +1798,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Artillery/Sidewinder X1/V1/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Artillery/Sidewinder X2/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Azteeg/X5GT/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIBO/TouchX/default/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR 1

config/examples/BIQU/B1 SE Plus/Configuration.h

@@ -1780,6 +1780,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIQU/B1 SE/Configuration.h

@@ -1780,6 +1780,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIQU/B1/Configuration.h

@@ -1793,6 +1793,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIQU/BX/Configuration.h

@@ -1789,6 +1789,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIQU/Hurakan/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BIQU/Thunder Standard/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BQ/Hephestos/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BQ/Hephestos_2/Configuration.h

@@ -1796,6 +1796,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/BQ/WITBOX/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR 1

config/examples/CTC/A13/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/CTC/Bizer/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR 1

config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Cartesio/Configuration.h

@@ -1798,6 +1798,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Copymaster3D/300/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Copymaster3D/400/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Copymaster3D/500/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 Max/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -1790,6 +1790,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -1790,6 +1790,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h

@@ -1791,6 +1791,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h

@@ -1784,6 +1784,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h

@@ -1785,6 +1785,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 V2/Configuration.h

@@ -1802,6 +1802,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10 V3/Configuration.h

@@ -1805,6 +1805,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -1781,6 +1781,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -1781,6 +1781,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10/CrealityV1/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10S Pro/Configuration.h

@@ -1782,6 +1782,8 @@
 #define Z_AFTER_HOMING           10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-10S/CrealityV1/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-20/Stock/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-30 PrintMill/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-6 SE/Configuration.h

@@ -1782,6 +1782,8 @@
 #define Z_AFTER_HOMING          5     // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/CR-8/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-2/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Max Neo/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Max/Configuration.h

@@ -1786,6 +1786,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Neo/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -1781,6 +1781,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h

@@ -1782,6 +1782,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h

@@ -1783,6 +1783,8 @@
 //#define Z_AFTER_HOMING         10   // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1

config/examples/Creality/Ender-3 S1 Plus/Configuration.h

@@ -1783,6 +1783,8 @@
 #define Z_AFTER_HOMING         10     // (mm) Height to move to after homing (if Z was homed)
 //#define XY_AFTER_HOMING { 10, 10 }  // (mm) Move to an XY position after homing (and raising Z)
 
+//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200"  // Commands to run after G28 (and move to XY_AFTER_HOMING)
+
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1