📝 Put DELTA / SCARA / TPARA in all configs (#776)

MarlinFirmware/Marlin#24458

config/default/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -847,6 +838,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1187,9 +1314,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 //===========================================================================
 //======================== Alfawise/Longer3D Printers =======================
 //===========================================================================
@@ -898,6 +889,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1274,9 +1401,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Alfawise/U20/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 //===========================================================================
 //======================== Alfawise/Longer3D Printers =======================
 //===========================================================================
@@ -899,6 +890,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1275,9 +1402,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AliExpress/CL-260/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/A2/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/A2plus/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/A6/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1222,9 +1349,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/A8/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -832,6 +823,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1208,9 +1335,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/A8plus/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/A9/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/E10/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/E16/BTT SKR 1.3/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/E16/Stock/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET4+/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -835,6 +826,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1211,9 +1338,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET4-Pro/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -835,6 +826,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1211,9 +1338,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET4/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -835,6 +826,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1211,9 +1338,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET4X/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -835,6 +826,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1211,9 +1338,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET5-Pro/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET5/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Anet/ET5X/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AnyCubic/Chiron/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -833,6 +824,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1209,9 +1336,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AnyCubic/i3 Mega/Configuration.h

@@ -62,15 +62,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -850,6 +841,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1235,9 +1362,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/AnyCubic/i3/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/ArmEd/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Genius Pro/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Genius/BLTouch/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Genius/V1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Hornet/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -844,6 +835,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1221,9 +1348,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Sidewinder X1/V1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Artillery/Sidewinder X2/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Azteeg/X5GT/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIBO/TouchX/default/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -785,6 +776,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1161,9 +1288,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIQU/B1 - SKR 1.4/Configuration.h

@@ -62,15 +62,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -832,6 +823,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1214,9 +1341,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIQU/B1 - SKR 2/Configuration.h

@@ -62,15 +62,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -832,6 +823,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1214,9 +1341,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIQU/B1 SE Plus/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -827,6 +818,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1203,9 +1330,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIQU/BX/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BIQU/Thunder Standard/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BQ/Hephestos/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BQ/Hephestos_2/Configuration.h

@@ -67,15 +67,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -843,6 +834,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1219,9 +1346,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/BQ/WITBOX/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/CTC/A13/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/CTC/Bizer/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Cartesio/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -845,6 +836,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1221,9 +1348,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Copymaster3D/300/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Copymaster3D/400/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Copymaster3D/500/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -68,15 +68,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -837,6 +828,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1214,9 +1341,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h

@@ -68,15 +68,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -838,6 +829,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1214,9 +1341,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1207,9 +1334,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 V2/Configuration.h

@@ -66,15 +66,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -838,6 +829,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1223,9 +1350,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10 V3/Configuration.h

@@ -66,15 +66,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -838,6 +829,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1224,9 +1351,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -828,6 +819,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1204,9 +1331,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10/CrealityV1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-10S/CrealityV1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-20/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-30 PrintMill/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/CR-8/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-2/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Max/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -831,6 +822,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1209,9 +1336,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 S1/Configuration.h

@@ -39,6 +39,7 @@
  */
 #define CONFIGURATION_H_VERSION 02000905
 
+
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
@@ -59,15 +60,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +821,7 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1198,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 S1/Configuration_adv.h

@@ -32,6 +32,7 @@
  */
 #define CONFIGURATION_ADV_H_VERSION 02000905
 
+
 //===========================================================================
 //============================= Thermal Settings ============================
 //===========================================================================

config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -827,6 +818,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1203,9 +1330,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -827,6 +818,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1203,9 +1330,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -829,6 +820,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1205,9 +1332,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -828,6 +819,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1204,9 +1331,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -830,6 +821,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1206,9 +1333,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -828,6 +819,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1204,9 +1331,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -828,6 +819,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1204,9 +1331,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }

config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h

@@ -59,15 +59,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -828,6 +819,142 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
+//#define ARTICULATED_ROBOT_ARM
+
+// For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
+// ends are controlled by parallel axes (Y, J). Joints are directly mapped to axes (no kinematics).
+//#define FOAMCUTTER_XYUV
+
+
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1204,9 +1331,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }