diff --git a/config/default/Configuration.h b/config/default/Configuration.h index a9d2d55a16..898a680333 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -608,10 +608,12 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** + #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -633,7 +635,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index e4a1c33191..f38b5357db 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 3.22 #define DEFAULT_Kd 65.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index 1ce71ac442..7886a39b7d 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index 43fdb8a1ae..c9cabf828c 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index 829b246822..4b40cd57c3 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -659,10 +659,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -688,7 +689,45 @@ #define DEFAULT_Ki 1.00 #define DEFAULT_Kd 74.22 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index e1cf0f9621..f832312a8d 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -659,10 +659,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -688,7 +689,45 @@ #define DEFAULT_Ki 1.00 #define DEFAULT_Kd 74.22 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 8bcbb308e9..088202e7c3 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 1d74308cef..a1ebe759ed 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.69 #define DEFAULT_Kd 34.32 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index d98bebfeb2..bac636a3e0 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 1ae97527be..c435b60b07 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 485727d7fe..766824f167 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.02 #define DEFAULT_Kd 69.29 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 90bf6b4080..6e6588e770 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 1.25 #define DEFAULT_Kd 86.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 34d2fb1082..87bb12fe68 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 6.33 #define DEFAULT_Kd 95.60 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h index e1568e047e..feedc93e8e 100644 --- a/config/examples/Anet/A9/Configuration.h +++ b/config/examples/Anet/A9/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.47 #define DEFAULT_Kd 93.27 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index 7e17ab8151..0d6b956cc5 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h index a5eb94328f..7574675a9b 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.25 #define DEFAULT_Kd 86.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h index dd5570d008..50485718b5 100644 --- a/config/examples/Anet/E16/Stock/Configuration.h +++ b/config/examples/Anet/E16/Stock/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.25 #define DEFAULT_Kd 86.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET4+/Configuration.h b/config/examples/Anet/ET4+/Configuration.h index bd04373d23..ac3260d301 100644 --- a/config/examples/Anet/ET4+/Configuration.h +++ b/config/examples/Anet/ET4+/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 1.38 #define DEFAULT_Kd 62.92 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET4-Pro/Configuration.h b/config/examples/Anet/ET4-Pro/Configuration.h index a763a05985..50f8e72753 100644 --- a/config/examples/Anet/ET4-Pro/Configuration.h +++ b/config/examples/Anet/ET4-Pro/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 1.38 #define DEFAULT_Kd 62.92 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h index 7386765b5a..a5e1232526 100644 --- a/config/examples/Anet/ET4/Configuration.h +++ b/config/examples/Anet/ET4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 1.38 #define DEFAULT_Kd 62.92 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET4X/Configuration.h b/config/examples/Anet/ET4X/Configuration.h index 8688567b52..2c1fe24eed 100644 --- a/config/examples/Anet/ET4X/Configuration.h +++ b/config/examples/Anet/ET4X/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 1.38 #define DEFAULT_Kd 62.92 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET5-Pro/Configuration.h b/config/examples/Anet/ET5-Pro/Configuration.h index 9273d5d214..34860f6596 100644 --- a/config/examples/Anet/ET5-Pro/Configuration.h +++ b/config/examples/Anet/ET5-Pro/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.03 #define DEFAULT_Kd 71.17 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET5/Configuration.h b/config/examples/Anet/ET5/Configuration.h index f21578271a..a7755fb397 100644 --- a/config/examples/Anet/ET5/Configuration.h +++ b/config/examples/Anet/ET5/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.03 #define DEFAULT_Kd 71.17 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Anet/ET5X/Configuration.h b/config/examples/Anet/ET5X/Configuration.h index f5618d22bf..7e15d8a7df 100644 --- a/config/examples/Anet/ET5X/Configuration.h +++ b/config/examples/Anet/ET5X/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.03 #define DEFAULT_Kd 71.17 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h index 6944383727..394c201adf 100644 --- a/config/examples/AnyCubic/Chiron/Configuration.h +++ b/config/examples/AnyCubic/Chiron/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -634,7 +635,45 @@ #define DEFAULT_Ki 0.86 #define DEFAULT_Kd 60.97 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h index 803f562f42..88a05cf3fe 100644 --- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.18 #define DEFAULT_Kd 66.76 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h index 0e58beaa0c..7f960e9b4e 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.18 #define DEFAULT_Kd 66.76 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h index b06c8d6239..06133b11dd 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.18 #define DEFAULT_Kd 66.76 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h index c4426c6213..f2dc4eed1a 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration.h @@ -625,10 +625,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -651,7 +652,45 @@ #define DEFAULT_Ki 1.17 #define DEFAULT_Kd 54.19 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index e9d031aad4..7ef9b87460 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.84 #define DEFAULT_Kd 64.84 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index ff2cb061c6..93c66d8598 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.57 #define DEFAULT_Kd 53.37 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Genius Pro/Configuration.h b/config/examples/Artillery/Genius Pro/Configuration.h index 1d30d11a1c..bb62d4ac04 100644 --- a/config/examples/Artillery/Genius Pro/Configuration.h +++ b/config/examples/Artillery/Genius Pro/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.04 #define DEFAULT_Kd 23.88 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Genius/BLTouch/Configuration.h b/config/examples/Artillery/Genius/BLTouch/Configuration.h index b3416c9f56..b1d592d148 100644 --- a/config/examples/Artillery/Genius/BLTouch/Configuration.h +++ b/config/examples/Artillery/Genius/BLTouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.57 #define DEFAULT_Kd 37.76 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Genius/V1/Configuration.h b/config/examples/Artillery/Genius/V1/Configuration.h index 706ead9f4f..2d24a11d0e 100644 --- a/config/examples/Artillery/Genius/V1/Configuration.h +++ b/config/examples/Artillery/Genius/V1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.57 #define DEFAULT_Kd 37.76 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Hornet/Configuration.h b/config/examples/Artillery/Hornet/Configuration.h index 20c5f3ce28..a522534e67 100644 --- a/config/examples/Artillery/Hornet/Configuration.h +++ b/config/examples/Artillery/Hornet/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 0.97 #define DEFAULT_Kd 59.78 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h index faff98b091..46800339a7 100644 --- a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -640,7 +641,45 @@ #define DEFAULT_Ki 5.69 #define DEFAULT_Kd 56.64 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h index 3dfd32d327..416ecbaff0 100644 --- a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.14 #define DEFAULT_Kd 46.57 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Artillery/Sidewinder X2/Configuration.h b/config/examples/Artillery/Sidewinder X2/Configuration.h index 743948f9d3..ec3716e97f 100644 --- a/config/examples/Artillery/Sidewinder X2/Configuration.h +++ b/config/examples/Artillery/Sidewinder X2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.14 #define DEFAULT_Kd 46.57 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 0f2a8d2234..4b77c67d28 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 6b3ec102c0..ae45699ba5 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.37 #define DEFAULT_Kd 104.50 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 6edc6eb96b..3c0278db27 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.37 #define DEFAULT_Kd 104.50 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h index b2e0c100ae..79cbd50afd 100644 --- a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h +++ b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 1.85 #define DEFAULT_Kd 73.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIQU/B1 - SKR 2/Configuration.h b/config/examples/BIQU/B1 - SKR 2/Configuration.h index cd4cd8eb51..9930ad12b0 100644 --- a/config/examples/BIQU/B1 - SKR 2/Configuration.h +++ b/config/examples/BIQU/B1 - SKR 2/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 1.85 #define DEFAULT_Kd 73.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIQU/B1 SE Plus/Configuration.h b/config/examples/BIQU/B1 SE Plus/Configuration.h index 1455b40f40..f88809a3aa 100644 --- a/config/examples/BIQU/B1 SE Plus/Configuration.h +++ b/config/examples/BIQU/B1 SE Plus/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.49 #define DEFAULT_Kd 80.40 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIQU/BX/Configuration.h b/config/examples/BIQU/BX/Configuration.h index 95901ea627..7a4cbff337 100644 --- a/config/examples/BIQU/BX/Configuration.h +++ b/config/examples/BIQU/BX/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.55 #define DEFAULT_Kd 46.14 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BIQU/Thunder Standard/Configuration.h b/config/examples/BIQU/Thunder Standard/Configuration.h index dd564b6aec..19552b0b4d 100644 --- a/config/examples/BIQU/Thunder Standard/Configuration.h +++ b/config/examples/BIQU/Thunder Standard/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 3e36cb682c..09e3aaf772 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.00 #define DEFAULT_Kd 66.47 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index a355316f2d..92a9b7e45c 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -612,10 +612,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -643,7 +644,45 @@ //#define DEFAULT_Ki 0.45 //#define DEFAULT_Kd 3.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 55540f4ea5..d23e06cf79 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/CTC/A13/Configuration.h b/config/examples/CTC/A13/Configuration.h index 5e69bd5087..6a0372a78d 100644 --- a/config/examples/CTC/A13/Configuration.h +++ b/config/examples/CTC/A13/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/CTC/Bizer/Configuration.h b/config/examples/CTC/Bizer/Configuration.h index a876a770f6..bf49790f15 100644 --- a/config/examples/CTC/Bizer/Configuration.h +++ b/config/examples/CTC/Bizer/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.07 #define DEFAULT_Kd 70.38 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index 134fd285b3..e9d4fd5b13 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.00 #define DEFAULT_Kd 98.93 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index d0f097ded9..1cb4b8e765 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -641,7 +642,45 @@ //#define DEFAULT_Ki 1.0 //#define DEFAULT_Kd 100.0 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index 598f481d6c..c1a96afd13 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 16.53 #define DEFAULT_Kd 113.58 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 34819f9306..4e2c2642fe 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index cdf241dc84..7cd8b05195 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 16.53 #define DEFAULT_Kd 113.58 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h index 61893a1da1..3d98092cd5 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -613,10 +613,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -639,7 +640,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h index 85fcfb716c..5356cc8561 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h @@ -613,10 +613,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -639,7 +640,45 @@ #define DEFAULT_Ki 1.72 #define DEFAULT_Kd 73.96 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h index 099a89a066..c1d089c343 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.11 #define DEFAULT_Kd 75.35 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h index b2184c4b78..363ef1283d 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h index f18abb7cbb..2b188145b0 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h index afa1af78f8..55e95d60bc 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h index 4cdbc71ba4..188dcf4d87 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.59 #define DEFAULT_Kd 68.97 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index 72c5cc8455..e9b75d40b8 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -611,10 +611,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -637,7 +638,45 @@ #define DEFAULT_Ki 1.59 #define DEFAULT_Kd 59.40 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10 V3/Configuration.h b/config/examples/Creality/CR-10 V3/Configuration.h index 38c140a05d..8cd8ffee19 100644 --- a/config/examples/Creality/CR-10 V3/Configuration.h +++ b/config/examples/Creality/CR-10 V3/Configuration.h @@ -611,10 +611,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -637,7 +638,45 @@ #define DEFAULT_Ki 1.59 #define DEFAULT_Kd 59.40 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h index c69cd84790..485b0bdddb 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h index f1615834d0..0006429303 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.72 #define DEFAULT_Kd 73.96 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h index a4a8ff4fd1..e6194defc0 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h index a0c1e87670..7dddb7cd29 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.46 #define DEFAULT_Kd 92.02 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h index ea34299e14..e6fec2a1f3 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h index 569cc14648..056051824f 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h index 7058ad7413..5e5f422405 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index 032d18e191..1459a437e3 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 74ec8c9f60..70a643e65f 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration.h b/config/examples/Creality/CR-30 PrintMill/Configuration.h index eb3c6ff01e..aab58fef89 100644 --- a/config/examples/Creality/CR-30 PrintMill/Configuration.h +++ b/config/examples/Creality/CR-30 PrintMill/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.14 #define DEFAULT_Kd 68.33 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h index 7bc611dc69..f4884cf447 100644 --- a/config/examples/Creality/CR-6 SE/Configuration.h +++ b/config/examples/Creality/CR-6 SE/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 0.81 #define DEFAULT_Kd 63.12 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 70ae090d1e..38f41b1868 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h index 880116b2d0..0a8be98562 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.62 #define DEFAULT_Kd 78.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 666cf49357..fad9f7e245 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Max/Configuration.h b/config/examples/Creality/Ender-3 Max/Configuration.h index 53542acaf7..0f384ab8ec 100644 --- a/config/examples/Creality/Ender-3 Max/Configuration.h +++ b/config/examples/Creality/Ender-3 Max/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.56 #define DEFAULT_Kd 73.30 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h index 4a8a53933f..10942b4e5e 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h index 6ccb245934..232262ce39 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index 2e980490cb..eaef4ca237 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h index 1841b0da73..57254dc473 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h index fea7f135aa..56f3afc183 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h index 6ffe717ed7..e882874a22 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h index f7434a0e1b..fe9ca56cdb 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.62 #define DEFAULT_Kd 78.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h index bd1abf9a79..25a3e5a91b 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 S1/Configuration.h b/config/examples/Creality/Ender-3 S1/Configuration.h index ca49581502..c95c576ef2 100644 --- a/config/examples/Creality/Ender-3 S1/Configuration.h +++ b/config/examples/Creality/Ender-3 S1/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.87 #define DEFAULT_Kd 70.18 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h index 6b5a8eba4e..667d22e763 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.62 #define DEFAULT_Kd 78.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h index 7f8407d401..68d113e50f 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.62 #define DEFAULT_Kd 78.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h index a4b54ff53c..94a1043f08 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.62 #define DEFAULT_Kd 78.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h index 8d9f63c55d..4dff8df27e 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.62 #define DEFAULT_Kd 78.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h index c73315ff18..02961b3342 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h index fcdffc7711..bd98f64dea 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h index abf3678848..096e1d0eb4 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h index b6f56e841f..78b4960940 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h index d6725f1b5e..36c88fd99a 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h index 4b00fbf415..3ebfebf8a5 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index ee75334789..a3d8f98676 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index 305d59c12e..0250b0c9c0 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index 862c00aece..e1de20c460 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h index 981e4f0eb7..7dd8d6f140 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index e61be3943b..91e6f2c0fd 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h index 8ab99364e6..8e9e3005a5 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h index e97d2ddbc1..3f2b4eeb91 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index fcc70a9a5f..e571536670 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 6f6ab86535..026e378903 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h index e8feb40048..90ad4b5d63 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index f09d38a60c..795227583a 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index 1083ffc383..212f8253a7 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index 25a1853b11..a853696f72 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.11 #define DEFAULT_Kd 75.35 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h index 0b39e3e19e..2b49ba5fc2 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h index b5d0f5c786..3c804a5968 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h index c30a7aef66..93b0f57df0 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h index fa59652733..0740459bfe 100644 --- a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h +++ b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index 88ff55fd2e..5fb96239e0 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.12 #define DEFAULT_Kd 62.14 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h index 53a68d08a2..ed5ba49460 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 1.38 #define DEFAULT_Kd 68.38 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h index b5b67860a3..eacfff5e0e 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index b22aef598b..e7dda394d7 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h index f2b990a09e..08ac9fcd92 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h index 7369b39dbb..c6729239b7 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h index 5e6f4113bc..3fbc1f21d9 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h index 1ae9439719..a33b711b4e 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h index 95a46ed004..a3cd88db41 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h index 2236b4a7a8..6279fb3aa7 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h index 08a5b3709f..df6e8dabff 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index 6339b53f44..c7cbf89d5c 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h index fd844dfa38..7a2e0024c8 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h index bc64bb4a9d..786c8f8ff6 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Creality/Ender-6/Configuration.h b/config/examples/Creality/Ender-6/Configuration.h index e80b5bff29..9da90b9ab5 100644 --- a/config/examples/Creality/Ender-6/Configuration.h +++ b/config/examples/Creality/Ender-6/Configuration.h @@ -607,10 +607,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -632,7 +633,45 @@ #define DEFAULT_Ki 3.10 #define DEFAULT_Kd 75.84 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 5f74fd2ecd..61e1927859 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 6.40 #define DEFAULT_Kd 41.25 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index cb97ec5594..a5b554dd99 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -607,10 +607,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -633,7 +634,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 7af783ce4c..41ff735c68 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 0.44 #define DEFAULT_Kd 71.37 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h index b3615f2619..dac061ca75 100644 --- a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h +++ b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index d43cbda41e..7289fde0c2 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.93 #define DEFAULT_Kd 63.03 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Elegoo/Neptune 2/Configuration.h b/config/examples/Elegoo/Neptune 2/Configuration.h index 9dfaec2074..b7935de785 100644 --- a/config/examples/Elegoo/Neptune 2/Configuration.h +++ b/config/examples/Elegoo/Neptune 2/Configuration.h @@ -673,10 +673,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -699,7 +700,45 @@ #define DEFAULT_Ki 2.11 #define DEFAULT_Kd 76.90 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Eryone/Thinker SE/Configuration.h b/config/examples/Eryone/Thinker SE/Configuration.h index 60956dd1b2..a74173af94 100644 --- a/config/examples/Eryone/Thinker SE/Configuration.h +++ b/config/examples/Eryone/Thinker SE/Configuration.h @@ -612,10 +612,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -637,7 +638,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Eryone/Thinker V2/Configuration.h b/config/examples/Eryone/Thinker V2/Configuration.h index 3a549d6a6b..a2733be423 100644 --- a/config/examples/Eryone/Thinker V2/Configuration.h +++ b/config/examples/Eryone/Thinker V2/Configuration.h @@ -611,10 +611,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -636,7 +637,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index e5ce62922a..650d5cbbc7 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 76.55 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 2cd373b419..37d0915196 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index 44016448ab..671aba2440 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 2271c6ff72..06f5cd6a55 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.84 #define DEFAULT_Kd 85.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index c66e4f7aed..44b69ea8d3 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.84 #define DEFAULT_Kd 85.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index 61879e239a..96c170cca3 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.22 #define DEFAULT_Kd 82.05 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index b47dcb2274..d624d0ca5b 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.22 #define DEFAULT_Kd 82.05 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FlyingBear/P902/Configuration.h b/config/examples/FlyingBear/P902/Configuration.h index a722788dbe..b1b56e4e4a 100644 --- a/config/examples/FlyingBear/P902/Configuration.h +++ b/config/examples/FlyingBear/P902/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index 10d4df46ff..8c0120ddd6 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.16 #define DEFAULT_Kd 150.60 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FoamCutter/Configuration.h b/config/examples/FoamCutter/Configuration.h index 5eded644c8..69a920bdee 100644 --- a/config/examples/FoamCutter/Configuration.h +++ b/config/examples/FoamCutter/Configuration.h @@ -603,10 +603,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -628,7 +629,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 61e42317d6..8ef68b27ba 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.50 #define DEFAULT_Kd 60.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 8229c2ce3e..72bcbe2bd8 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -653,10 +653,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -688,7 +689,45 @@ #define DEFAULT_Ki HOTEND_Ki #define DEFAULT_Kd HOTEND_Kd #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 49b9f4fddb..1a066052e9 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 180 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.46 #define DEFAULT_Kd 64.31 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index bcb578ee7e..ef520d7337 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -607,10 +607,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -633,7 +634,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index f9df457f5e..bb4a48f15d 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index 1b452e6fc7..7a5f16ff79 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 0.43 #define DEFAULT_Kd 854.89 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h index aa0999ad47..ba19f1b22c 100644 --- a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h index 41c428cf85..6519b0037d 100644 --- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10PRO/Configuration.h b/config/examples/Geeetech/A10PRO/Configuration.h index 6d326f485c..cd66ba203c 100644 --- a/config/examples/Geeetech/A10PRO/Configuration.h +++ b/config/examples/Geeetech/A10PRO/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h index cd01c0fb0e..73c7d8b829 100644 --- a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h index 21f43de889..2027bd5c0a 100644 --- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index d6d0c3588a..2ed809b86b 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index d073a5d5b6..ec9dd30449 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index 5e0be1d42e..895894a785 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 74d5155454..1b75ac6aa2 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A30M/Configuration.h b/config/examples/Geeetech/A30M/Configuration.h index 8bea78778a..3af3929daa 100644 --- a/config/examples/Geeetech/A30M/Configuration.h +++ b/config/examples/Geeetech/A30M/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/A30T/Configuration.h b/config/examples/Geeetech/A30T/Configuration.h index 442ac02373..4885ba767d 100644 --- a/config/examples/Geeetech/A30T/Configuration.h +++ b/config/examples/Geeetech/A30T/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index 4ff9d9e03d..f0ed8200ee 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index 1aedf911f7..2543d3e0df 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index b100d03224..b391cc8b70 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 3.61 #define DEFAULT_Kd 145.39 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 61694181b9..e7df8f57ae 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ //#define DEFAULT_Ki 1.00 //#define DEFAULT_Kd 98.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 84d4066046..235b23510a 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index a5e8852d5b..262558655a 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 09d0a78799..c548dca1bb 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.59 #define DEFAULT_Kd 59.89 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index 440be5d98d..ed5f7b9295 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 048593bb8d..85b6a6ef05 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.00 #define DEFAULT_Kd 98.93 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index ae1a1911c2..f1f633f6b3 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ //#define DEFAULT_Ki 1.00 //#define DEFAULT_Kd 98.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 60094b9ddb..ea8e8b2f08 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ //#define DEFAULT_Ki 1.00 //#define DEFAULT_Kd 98.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index a7160840f4..94076bcbbe 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ //#define DEFAULT_Ki 1.00 //#define DEFAULT_Kd 98.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 517ab2bfd3..eadacbbe18 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index ba653eef12..9e21d27658 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 640cf8bcb1..3aeb120b79 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -602,10 +602,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX 170 // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -627,7 +628,45 @@ #define DEFAULT_Ki 0.61 #define DEFAULT_Kd 52.77 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Index/REV_03/Configuration.h b/config/examples/Index/REV_03/Configuration.h index 12f5e06b19..e638b42c19 100644 --- a/config/examples/Index/REV_03/Configuration.h +++ b/config/examples/Index/REV_03/Configuration.h @@ -609,10 +609,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -634,7 +635,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 83fa913cc5..04ec83bc6a 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.54 #define DEFAULT_Kd 765.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h index e58f12d07e..d020ccf73f 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 0.45 #define DEFAULT_Kd 70.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index b82ca4e880..feac8b56ac 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 3.68 #define DEFAULT_Kd 72.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index d06e4be670..fbfd6c9200 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index cb0c8f0974..4ce97b5494 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -609,10 +609,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 4.35 #define DEFAULT_Kd 71.57 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index e86212a3da..732f0d6b13 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 3.68 #define DEFAULT_Kd 72.83 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index a5652a0b8e..bfc41596f1 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index 73fda2f527..6678ebb11e 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Kingroon/KP3S/Configuration.h b/config/examples/Kingroon/KP3S/Configuration.h index 3e2716e144..c233cb7fa9 100644 --- a/config/examples/Kingroon/KP3S/Configuration.h +++ b/config/examples/Kingroon/KP3S/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Labists/ET4/Configuration.h b/config/examples/Labists/ET4/Configuration.h index cbca1497fc..246f452ef7 100644 --- a/config/examples/Labists/ET4/Configuration.h +++ b/config/examples/Labists/ET4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 1.38 #define DEFAULT_Kd 62.92 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/LulzBot/TAZ4/Configuration.h b/config/examples/LulzBot/TAZ4/Configuration.h index 6b00f486c4..cc8d13078c 100644 --- a/config/examples/LulzBot/TAZ4/Configuration.h +++ b/config/examples/LulzBot/TAZ4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 70 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX 74 // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ //#define DEFAULT_Ki 1.01 //#define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index 844d338018..3ea19d5e19 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.22 #define DEFAULT_Kd 82.05 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h index 4bdcabad6d..ea12d0dbbe 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 4d7a920ded..99b39e4091 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 14059f1a66..6fac86d909 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -612,10 +612,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -638,7 +639,45 @@ #define DEFAULT_Ki 2.0 #define DEFAULT_Kd 97.0 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Malyan/M180/Configuration.h b/config/examples/Malyan/M180/Configuration.h index 314bdb2370..2c7e0c4069 100644 --- a/config/examples/Malyan/M180/Configuration.h +++ b/config/examples/Malyan/M180/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index 7d6aa2c6b1..f85eb8e8dc 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.02 #define DEFAULT_Kd 100.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index de761891d1..3d51f77bb0 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index ca2fc9637e..a3c884e4a1 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 33dee563ee..c3a813719e 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index 59c3140ade..11ce0b6dda 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -610,10 +610,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -635,7 +636,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index a30889519f..fec75ff292 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index fb9a1c5387..a72bf00239 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index 11083a349f..74728ab4fb 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 59.50 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Nextion/Configuration.h b/config/examples/Nextion/Configuration.h index 288a11fe19..1f7ea5b435 100644 --- a/config/examples/Nextion/Configuration.h +++ b/config/examples/Nextion/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index 005562a7fb..62365e869d 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.68 #define DEFAULT_Kd 73.75 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Polargraph/Configuration.h b/config/examples/Polargraph/Configuration.h index 88d3b1d2c8..cdf5c229f4 100644 --- a/config/examples/Polargraph/Configuration.h +++ b/config/examples/Polargraph/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index aa2decb8e1..08cc40d470 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index f8cb32f9ea..f6221b12e0 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Prusa/MK3/Configuration.h b/config/examples/Prusa/MK3/Configuration.h index 6112a6770b..b7ccf37fec 100644 --- a/config/examples/Prusa/MK3/Configuration.h +++ b/config/examples/Prusa/MK3/Configuration.h @@ -627,10 +627,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -653,7 +654,45 @@ #define DEFAULT_Ki 1.1625 #define DEFAULT_Kd 56.23 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index bd32b46535..73147a2f41 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -620,10 +620,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -646,7 +647,45 @@ #define DEFAULT_Ki 1.1625 #define DEFAULT_Kd 56.2300 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index 066632d4e0..d6bab75ea0 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 3.81 #define DEFAULT_Kd 24.57 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h index eb6da10a20..f91c0fb4d3 100644 --- a/config/examples/Raiscube/A8r/Configuration.h +++ b/config/examples/Raiscube/A8r/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.02 #define DEFAULT_Kd 69.29 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 779e8b108c..9deae8d1ca 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index 11b9760083..fc51b17280 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -634,7 +635,45 @@ #define DEFAULT_Ki 1.3 #define DEFAULT_Kd 70.1 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index 06a38a3760..17de67d9db 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -634,7 +635,45 @@ #define DEFAULT_Ki 1.3 #define DEFAULT_Kd 70.1 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 9daaf6ef16..b3ea47df3c 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -634,7 +635,45 @@ #define DEFAULT_Ki 1.3 #define DEFAULT_Kd 70.1 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index e99eaa9a5d..d2ed6303ea 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index e518f80f2d..3597105080 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 4acbe6c29a..7e9df4ba89 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -642,7 +643,45 @@ //#define DEFAULT_Ki 0.95 //#define DEFAULT_Kd 69.69 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index d6eeb24114..b8dc64099b 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index b1436924fd..de59546aea 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -649,10 +649,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -675,7 +676,45 @@ #define DEFAULT_Ki 1.72 #define DEFAULT_Kd 87.73 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 80d8201b07..d344ef249b 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -649,10 +649,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -675,7 +676,45 @@ #define DEFAULT_Ki 1.72 #define DEFAULT_Kd 87.73 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index 0f6d1ec788..2a691eb398 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index f145fce0bb..a6057e6b59 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 180 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index eb77332131..529baf1419 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 0f8d605908..6fa2af4ed3 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Simulator/Configuration.h b/config/examples/Simulator/Configuration.h index f9dc98aeef..83a0eb5f82 100644 --- a/config/examples/Simulator/Configuration.h +++ b/config/examples/Simulator/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h index 3f661c9784..cbbcc61be3 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h index 88a825ec7d..abf6948c2e 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.93 #define DEFAULT_Kd 75.58 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h index eb281193d3..146e666a03 100644 --- a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.93 #define DEFAULT_Kd 75.58 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h index ecb6d1bab6..2953cbd0d2 100644 --- a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.93 #define DEFAULT_Kd 75.58 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Sunlu/S8/Configuration.h b/config/examples/Sunlu/S8/Configuration.h index 591d567bf6..8d3568a343 100644 --- a/config/examples/Sunlu/S8/Configuration.h +++ b/config/examples/Sunlu/S8/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.47 #define DEFAULT_Kd 61.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration.h b/config/examples/TPARA/AXEL_TPARA/Configuration.h index f4a3ab7385..7333acee4a 100644 --- a/config/examples/TPARA/AXEL_TPARA/Configuration.h +++ b/config/examples/TPARA/AXEL_TPARA/Configuration.h @@ -624,10 +624,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -650,7 +651,45 @@ #define DEFAULT_Ki 1.72 #define DEFAULT_Kd 87.73 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index 0f0697dee0..d3c64a022c 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.39 #define DEFAULT_Kd 69.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 794bc1a7db..9cd15150dd 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.82 #define DEFAULT_Kd 44.71 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index 4a18f87bcc..a7cdb3c4c7 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.49 #define DEFAULT_Kd 69.41 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 806c1097cf..2057538b8a 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.50 #define DEFAULT_Kd 69.26 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index 1f5afaeddf..2fd7e518e8 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.50 #define DEFAULT_Kd 69.26 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index a99790e717..6f5d3a0faf 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.42 #define DEFAULT_Kd 58.34 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index db5ae0a642..8be50b1ca1 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -631,10 +631,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -663,7 +664,45 @@ #define DEFAULT_Ki 2.71 #define DEFAULT_Kd 63.02 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 4b0c65765c..0ca2d9812f 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.11 #define DEFAULT_Kd 59.06 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 9dd9d188c9..ee52af3d5f 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index 568eb31070..79cffc6ec6 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -636,7 +637,45 @@ #define DEFAULT_Ki 2.41 #define DEFAULT_Kd 71.28 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index cc2aa62a01..f990a93b37 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/X5SA-2E/Configuration.h b/config/examples/Tronxy/X5SA-2E/Configuration.h index 985f9d51c7..06078b439d 100644 --- a/config/examples/Tronxy/X5SA-2E/Configuration.h +++ b/config/examples/Tronxy/X5SA-2E/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.05 #define DEFAULT_Kd 66.74 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index f87fa9602f..d34f36b3b7 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 0100a100ba..549b5384b6 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -636,7 +637,45 @@ #define DEFAULT_Ki 2.0 #define DEFAULT_Kd 40.0 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Two Trees/BlueR Plus/Configuration.h b/config/examples/Two Trees/BlueR Plus/Configuration.h index b96bc377d8..01ea9ac915 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration.h @@ -605,10 +605,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,45 @@ #define DEFAULT_Ki 2.90 #define DEFAULT_Kd 52.3 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h index b20a9e5778..a01c94f897 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h @@ -607,10 +607,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -633,7 +634,45 @@ #define DEFAULT_Ki 1.24 #define DEFAULT_Kd 49.77 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h index 5ba71d27bf..3fb3fdad0d 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -634,7 +635,45 @@ #define DEFAULT_Ki 1.24 #define DEFAULT_Kd 49.77 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h index 472a404713..d47659c78b 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h @@ -607,10 +607,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -633,7 +634,45 @@ #define DEFAULT_Ki 1.24 #define DEFAULT_Kd 49.77 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h index 33ee3434cd..d8c347b723 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h @@ -610,10 +610,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -636,7 +637,45 @@ #define DEFAULT_Ki 0.75 #define DEFAULT_Kd 49.50 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h index c6afe55993..39b061ea89 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h @@ -608,10 +608,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -633,7 +634,45 @@ #define DEFAULT_Ki 0.37 #define DEFAULT_Kd 44.46 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 724cad7de2..0b4c14e6e4 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index 155e5e56ce..e53f07740b 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Ultimaker/Ultimaker 2/Configuration.h b/config/examples/Ultimaker/Ultimaker 2/Configuration.h index dfb5aab4c8..60e1c1b61e 100644 --- a/config/examples/Ultimaker/Ultimaker 2/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker 2/Configuration.h @@ -607,10 +607,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -642,7 +643,45 @@ //#define DEFAULT_Ki 3.65 //#define DEFAULT_Kd 91.72 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h index 4df2392163..dfa94044e2 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h index 7a2320d857..9afa2947b6 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 7f77932477..1f5b23338f 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.56 #define DEFAULT_Kd 90.34 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index a5cd3bb653..f6ae3e6787 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -624,10 +624,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -650,7 +651,45 @@ #define DEFAULT_Ki 1.58 #define DEFAULT_Kd 93.51 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 191e737cb9..335aafaf33 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.25 #define DEFAULT_Kd 440.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 80f0885750..2140f37fc9 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.25 #define DEFAULT_Kd 440.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index f711bdca0f..cd25f893c3 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -617,10 +617,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -643,7 +644,45 @@ #define DEFAULT_Ki 5.34 #define DEFAULT_Kd 35.56 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index 8e6733bee9..8b1d865b51 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.22 #define DEFAULT_Kd 82.05 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index e0e8bca244..f252f5dce4 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 0.41 #define DEFAULT_Kd 50.98 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index a2c080dbe2..84932f3b44 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.0 #define DEFAULT_Kd 97.0 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 8187009823..81ef62e8d7 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h index 06efbd2071..9f97d5d15e 100644 --- a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.50 #define DEFAULT_Kd 102.90 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Weedo/Tina2/V2/Configuration.h b/config/examples/Weedo/Tina2/V2/Configuration.h index f190644f8b..95625d5ab7 100644 --- a/config/examples/Weedo/Tina2/V2/Configuration.h +++ b/config/examples/Weedo/Tina2/V2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.25 #define DEFAULT_Kd 440.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Weedo/Tina2/V3/Configuration.h b/config/examples/Weedo/Tina2/V3/Configuration.h index d8972bb802..33234dc112 100644 --- a/config/examples/Weedo/Tina2/V3/Configuration.h +++ b/config/examples/Weedo/Tina2/V3/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 2.25 #define DEFAULT_Kd 440.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index 0693b6a778..1f6117244c 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 1.10 #define DEFAULT_Kd 110.78 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index 51a8172f3b..6c2e18972d 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index 6424e93be1..ebcec341a1 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -606,10 +606,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -631,7 +632,46 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index 8dad33e2c6..bd4aaf0d3a 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index 07c665fa60..8421a4cd8b 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -611,10 +611,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -637,7 +638,45 @@ #define DEFAULT_Ki 1.63 #define DEFAULT_Kd 76.48 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 887be775de..66c5a31c46 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -614,10 +614,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -640,7 +641,45 @@ #define DEFAULT_Ki 1.63 #define DEFAULT_Kd 76.48 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index 5d8c4f8a9e..3bedcf50b7 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.01 #define DEFAULT_Kd 54.43 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 6676e0d29a..1154a1e3aa 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -594,10 +594,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 160 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 0.55 #define DEFAULT_Kd 33.89 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index 5a254c24ac..5a43a18df1 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -594,10 +594,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 160 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 0.55 #define DEFAULT_Kd 33.89 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h index 1c596a1ae1..7eee7cda40 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 0.58 #define DEFAULT_Kd 45.74 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h index c97971b131..de91e29f3e 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index 05aa9653bc..2e1ad97f0c 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 3.38 #define DEFAULT_Kd 58.69 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h index 9827dc2fd0..e363093d0f 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 1.2515 #define DEFAULT_Kd 93.8127 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 0f08fbe0a4..7ab8ff98e8 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 1.84 #define DEFAULT_Kd 83.61 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index beaad6f947..88062d7677 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 1.84 #define DEFAULT_Kd 83.61 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index d45162b8a7..ee25036a90 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 1.84 #define DEFAULT_Kd 83.61 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index d64faa6a7e..3a14b037a4 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index f69e137c4c..55cba9745e 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index d68105be67..81985d29f6 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index e8358d3dbb..510ac4ad6e 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index ea164d94b0..5f1ae52a55 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index ff658a8ce9..7f2629bc9f 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -600,10 +600,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -626,7 +627,45 @@ #define DEFAULT_Ki 2.71 #define DEFAULT_Kd 47.69 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 5d50cc253e..9ec3918187 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index 894d823416..a4bc336cfa 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 0.56 #define DEFAULT_Kd 62.47 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 2449ac424b..3d2e691d22 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -621,7 +622,45 @@ #define DEFAULT_Ki 2.96 #define DEFAULT_Kd 52.81 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index f68ab126c8..aac7c4e901 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index acf820ebf3..e252005261 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index a240e2924e..40f07a8954 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -620,7 +621,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index b086f35c5f..4cd2c2d8d5 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -599,10 +599,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX 125 // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -625,7 +626,45 @@ #define DEFAULT_Ki 3.51 #define DEFAULT_Kd 26.56 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 0106004f9d..b2e03c6b30 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -595,10 +595,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -626,7 +627,45 @@ //#define DEFAULT_Ki 1.45 //#define DEFAULT_Kd 85.30 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 53ca6aa496..701bb0cec7 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -610,10 +610,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -636,7 +637,45 @@ #define DEFAULT_Ki 0.85 #define DEFAULT_Kd 69.45 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h index ab5dd1d81f..0946aa55b0 100644 --- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h +++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h @@ -591,10 +591,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -616,7 +617,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 0b4530482e..651bcd775e 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -629,7 +630,45 @@ #define DEFAULT_Ki 1.08 #define DEFAULT_Kd 114.00 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ====================== diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index 21629c5d00..6ee04e51e0 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -604,10 +604,11 @@ //=========================================================================== //============================= PID Settings ================================ //=========================================================================== -// PID Tuning Guide here: https://reprap.org/wiki/PID_Tuning +// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model. +// temperature control. Disable both for bang-bang heating. +#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning +//#define MPCTEMP // ** EXPERIMENTAL ** -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop @@ -630,7 +631,45 @@ #define DEFAULT_Ki 2.30 #define DEFAULT_Kd 68.15 #endif -#endif // PIDTEMP +#endif + +/** + * Model Predictive Control for hotend + * + * Use a physical model of the hotend to control temperature. When configured correctly + * this gives better responsiveness and stability than PID and it also removes the need + * for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 to autotune the model. + */ +#if ENABLED(MPCTEMP) + #define MPC_MAX BANG_MAX // (0..255) Current to nozzle while MPC is active. + #define MPC_HEATER_POWER { 40.0f } // (W) Heat cartridge powers. + + #define MPC_INCLUDE_FAN // Model the fan speed? + + // Measured physical constants from M306 + #define MPC_BLOCK_HEAT_CAPACITY { 16.7f } // (J/K) Heat block heat capacities. + #define MPC_SENSOR_RESPONSIVENESS { 0.22f } // (K/s per ∆K) Rate of change of sensor temperature from heat block. + #define MPC_AMBIENT_XFER_COEFF { 0.068f } // (W/K) Heat transfer coefficients from heat block to room air with fan off. + #if ENABLED(MPC_INCLUDE_FAN) + #define MPC_AMBIENT_XFER_COEFF_FAN255 { 0.097f } // (W/K) Heat transfer coefficients from heat block to room air with fan on full. + #endif + + // For one fan and multiple hotends MPC needs to know how to apply the fan cooling effect. + #if ENABLED(MPC_INCLUDE_FAN) + //#define MPC_FAN_0_ALL_HOTENDS + //#define MPC_FAN_0_ACTIVE_HOTEND + #endif + + #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + + // Advanced options + #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. + #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. + #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. + + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. +#endif //=========================================================================== //====================== PID > Bed Temperature Control ======================