diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 4de7626b41..b81f55c4ac 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index fa744d9642..66f8b2a4ec 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index f120d9b3d2..6187e26eb9 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index c119fb1966..865dfdd5fa 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 366501ba7c..cfca896a89 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -1084,6 +1084,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index a520557dbd..9a5676f3e0 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -1129,6 +1129,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 8e51529800..068328c44e 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -1131,6 +1131,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index a0da7e3372..d4992e8c9e 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 8723a9d5d1..49fdba7f61 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index 54cfec21db..a3a3bbdf2a 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 8577653972..59121a89d7 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 31f7e7fa4c..07c199fa8a 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -1109,6 +1109,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 2d77023ec5..cbf3c7b7eb 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -1076,6 +1076,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index a4d0d56b0d..66320cc7b7 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h index 545d8c280c..fd6e85add2 100644 --- a/config/examples/Anet/A9/Configuration.h +++ b/config/examples/Anet/A9/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index d294d3be8f..8ecaa4d49c 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h index bc171d776c..367c5ae74e 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h index eb04f4bf14..893d49187a 100644 --- a/config/examples/Anet/E16/Stock/Configuration.h +++ b/config/examples/Anet/E16/Stock/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/ET4+/Configuration.h b/config/examples/Anet/ET4+/Configuration.h index a35dd39ce2..f4f60fc433 100644 --- a/config/examples/Anet/ET4+/Configuration.h +++ b/config/examples/Anet/ET4+/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/ET4-Pro/Configuration.h b/config/examples/Anet/ET4-Pro/Configuration.h index 9df30cbb99..5da6dd4a49 100644 --- a/config/examples/Anet/ET4-Pro/Configuration.h +++ b/config/examples/Anet/ET4-Pro/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h index ca3d9125db..cc9814809a 100644 --- a/config/examples/Anet/ET4/Configuration.h +++ b/config/examples/Anet/ET4/Configuration.h @@ -1079,6 +1079,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Anet/ET4X/Configuration.h b/config/examples/Anet/ET4X/Configuration.h index 8ca0481da8..52586aeb60 100644 --- a/config/examples/Anet/ET4X/Configuration.h +++ b/config/examples/Anet/ET4X/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h index b367a33a2f..ca75cb35d4 100644 --- a/config/examples/AnyCubic/Chiron/Configuration.h +++ b/config/examples/AnyCubic/Chiron/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h index ecef2e0f4d..f722e9c9ef 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h index cc0f75ddc7..8a68fccef3 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h index 87743ecfd2..a16c00f072 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration.h @@ -1089,6 +1089,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 75fdc2c3b9..d1738dc55c 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index effa49ac42..05246a112e 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Artillery/Genius/Configuration.h b/config/examples/Artillery/Genius/Configuration.h index 38fcdcbfb1..aa1e2ccfa3 100644 --- a/config/examples/Artillery/Genius/Configuration.h +++ b/config/examples/Artillery/Genius/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Artillery/Sidewinder X1/Configuration.h b/config/examples/Artillery/Sidewinder X1/Configuration.h index 9d19007c42..0a67757ec5 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h index 28e34ba60d..5c9710ce88 100644 --- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h @@ -1089,6 +1089,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 0610ad1bd9..8876bf4e05 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index f92e34879c..001b3adf8b 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 024bbb7fdc..d7ebd0aa07 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BIQU/B1-BLTouch/Configuration.h b/config/examples/BIQU/B1-BLTouch/Configuration.h index 16fe7d7b81..4e775dea4d 100644 --- a/config/examples/BIQU/B1-BLTouch/Configuration.h +++ b/config/examples/BIQU/B1-BLTouch/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BIQU/B1/Configuration.h b/config/examples/BIQU/B1/Configuration.h index 64bac439d0..8af5a1fa95 100644 --- a/config/examples/BIQU/B1/Configuration.h +++ b/config/examples/BIQU/B1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 41624c40f6..83b96c055e 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 0472fbf01b..26e095da3b 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -1087,6 +1087,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 400351a7c5..f4be732984 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index ef3134f260..6c9aa6f6a9 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index c28171f64f..5827cd33ff 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -1089,6 +1089,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index 4dff10f267..8dcf712a5c 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 330714b7d2..bebdad19da 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index 94fa53372b..4294f2f7f5 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h index e1ed0efd9c..7380ade123 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h @@ -1082,6 +1082,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h index f16f40985a..1daa14dc69 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h index c15d8687a7..9b752d9414 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h index 532b4f40e5..11f87a8dda 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index a3f0bf6134..e59c3adfd5 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -1090,6 +1090,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h index a4eb5c3669..b4e6bb0b5e 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h index 2454a7f881..dee212b00e 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h index e561a8af7e..25fde9f0ff 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h index 4002cf1159..96c498cbbf 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index 8ba0615b6e..d5d6b1cc86 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index a1fe039a74..c287338718 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h index 4800c2ae25..2051625fd5 100644 --- a/config/examples/Creality/CR-6 SE/Configuration.h +++ b/config/examples/Creality/CR-6 SE/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index fd4063c1c5..181a745026 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 9642df7b82..ee4560b0a4 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h index a6b3dcd848..6833bfd570 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index 466ecaeb10..5c47e769b3 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h index bfba1824b1..3720655a01 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h index cf7ec3c068..8a0935df60 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h index 77992416b2..41de651067 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h index 0f48afd838..d2b230e909 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3 V2/Configuration.h b/config/examples/Creality/Ender-3 V2/Configuration.h index 056ed257e5..4fcf4d12a5 100644 --- a/config/examples/Creality/Ender-3 V2/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h index afe1cc58d7..148ea7e450 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h index fc69786412..7381825c24 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h index 6c04fab030..f1b7321ecb 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h index 7f66fddbf4..245587bc20 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index 1d8849d3e9..f691294ffe 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index 95c8ad38f7..3005f7744c 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index 4c751b8844..849d309627 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index c94f8c1bb2..af21c8dd71 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h index 3161bb445f..9d53d3ca3c 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h index 6568d1e654..ffb0990c78 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index 56cb02183c..edec7cae62 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 56b0472162..1aa53aab28 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index 61d52742bc..a60c69aefc 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index 54d0b70e9d..2840c0dcc7 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index 0b4e30b296..3138739fba 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -1079,6 +1079,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h index eba2c65fc1..9c0849cfda 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h index aaa7db79d0..eedc313406 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index e38dab8cb7..305c629e8f 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h index 21ef16ff3e..41a6297607 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration.h @@ -1082,6 +1082,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h index ab14851321..322f06035f 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h index d03234749d..588c37c73f 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index 89f7aeeac6..c2b6103fb4 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h index ed1fad9f76..7184c55970 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h index bed176d2e5..97dd01455c 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h index 2d70263d79..5af5bacadf 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index a81fce4bf8..390cae4afd 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -1103,6 +1103,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h index d7877b98cb..275a56ad03 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h index 7661c93c5e..230c1b1679 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h index 7cfc0eed02..7dd1c35694 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index ce7efee2b2..57b4592cfe 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h index f089355cc6..181071cb83 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h index 5c7fa0f806..d42365fdab 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index ae0a0a0e4c..b937759c15 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index 0880a744ad..9f4aa5a3b9 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -1076,6 +1076,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 3c3dd6b8de..0119621d2a 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 1e5bdbc9cb..1ca42634ae 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -1078,6 +1078,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 418dadef3c..ec2ebbb088 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 4504cbcb1c..c3b72b66b3 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index 892a2ecafd..8476008a48 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 8a73911a65..6c9bc3246e 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index 6a106164b1..2647267c7b 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index 348c2e42a6..37eac96b50 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index 5fc61756a7..91a7901624 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index 79483903f9..424abe2a4c 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 19e4f5af1c..9e09ab83e2 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 7429be4f40..ca2502a222 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -1164,6 +1164,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 9e4118ec60..e6133dc650 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index 2d30976815..2dc0cd5a2e 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index 9972b20a17..a5325524da 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index 0554e469de..015c6b5c10 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index c18d6c2674..8cec15a6e7 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A10T/Configuration.h b/config/examples/Geeetech/A10T/Configuration.h index ffd3f2bc5b..f0ac9d19ee 100644 --- a/config/examples/Geeetech/A10T/Configuration.h +++ b/config/examples/Geeetech/A10T/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index 954a77a023..7963d53ff8 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index cdde334ff5..daf1dd2094 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index 81b4e9b374..845afc04d1 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 9345568fca..ae6af80aef 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -1071,6 +1071,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index 86410ec91c..1c8d0cea9d 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -1071,6 +1071,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index 45c2dffddd..9a9d111311 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index 523c769aed..c8c61c4ada 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 8ede5d5081..19d71280c1 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -1078,6 +1078,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 42201acd66..4fef7c63ba 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index ea2a52bec2..998a55a162 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -1071,6 +1071,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 637941a8b0..871aa16e52 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index 38948d2b64..16ac1a2ca8 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 3f4e636477..e0a2db0729 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index 7ca3c7ee30..58642fab86 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -1083,6 +1083,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 9f06f148b7..e9970105b6 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -1084,6 +1084,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 1e2ecd14c5..6edc29489f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -1083,6 +1083,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 808a3b295c..e6c72732d2 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 3ffbf0ca8c..45751f2724 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 96e12ff7b1..ee45c0ab17 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -1071,6 +1071,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 0f90334771..6d917850ab 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h index 6955ef0e87..9d0bab26b1 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index 22e1c9f6c8..7e886a7030 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index 4b72b5d7ca..feb045e792 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 9159d980ab..93d686d64e 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -1081,6 +1081,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index 921aba6648..3ec9e5255a 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index 36d8ae1f32..53b415e941 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index 242573866b..4dcce38c0f 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -1072,6 +1072,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index fee6d3a4f7..d3c67c6d8e 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h index 74487f12e7..99222faee8 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h @@ -1079,6 +1079,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 6637a1b665..41958d6f42 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index df9a1cdb61..9dd4a8385c 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -1097,6 +1097,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index 468610b7c2..987a9ce345 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -1079,6 +1079,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 9e1824a123..4fb4efd52a 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index de9dffd5e0..15ea7c2f22 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 984f2e7b53..cfe7f3f726 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index e5181fdc36..c48c6536b0 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index 47a95dc49c..a385f0f881 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index 0aa8200999..ab9cc5d005 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index acfd9d0ba0..63b0565745 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index fcf7f8f535..55d05c83e7 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index e89eabc893..87c37e4d58 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index e3432d46bc..7af010619e 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index 44ec55df7e..cc04e06c08 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index c0a66d9771..df500bb952 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -1076,6 +1076,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h index e34a522c38..86d92d2763 100644 --- a/config/examples/Raiscube/A8r/Configuration.h +++ b/config/examples/Raiscube/A8r/Configuration.h @@ -1110,6 +1110,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 6d68052a54..23054113e8 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index 1555b44fbd..19055cfafb 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index 909be87c45..b18f8bac5a 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 57cc35e90f..d65cc639e1 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 3125704dea..3a6ad8bd4a 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -1113,6 +1113,13 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index ffc44ff752..53059c303c 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 681b33ae39..5039c8ba19 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -1088,6 +1088,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index 2448f29457..2afc0e49fb 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 15f56fadec..61472c3482 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -1114,6 +1114,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index de244985b8..cef4ca2081 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -1114,6 +1114,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index 0c67bf0efc..2ae99888d6 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index 5a388cf52c..3bbff7e067 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 72ff152abf..e8a022cc1f 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index af0b301aaa..f03fcd659d 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -1104,6 +1104,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Sovol/SV-01/Configuration.h b/config/examples/Sovol/SV-01/Configuration.h index 462e0e2026..6b306a34b0 100644 --- a/config/examples/Sovol/SV-01/Configuration.h +++ b/config/examples/Sovol/SV-01/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index d65c4113ed..a523f20c58 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 92c1e9b0a3..16473384d8 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index 264a14b735..35ec60f649 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 2a9747d611..32417cce82 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index eb14404c89..4c1a216d94 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 9b8fcdbf54..7e6d361e4e 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1 diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 0da55dd62a..aef42136e7 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -1114,6 +1114,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 657b92b5a8..dcfc92d3ca 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index a0767bb163..63df83aec6 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index f38aeea602..da7094a835 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -1082,6 +1082,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 0f51b423eb..168b463df2 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index e6b566c8c4..0311689254 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index b3f9b10336..78ed0a2234 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h index dab68c0503..bf6c56e918 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h @@ -1091,6 +1091,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h index 1d78580257..36ed86e9a5 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h @@ -1092,6 +1092,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h index 3f05cf6a4e..32729e0bc9 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h @@ -1095,6 +1095,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h index c53ba2030a..0f970f9f6f 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h @@ -1109,6 +1109,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h index b64bd2bfd0..cf656dd8a7 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h @@ -1090,6 +1090,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index a7d7e7cf8c..421fcca4bc 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index f9032d6ad5..b742299cd7 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 2fc9b2975f..c124405dbd 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index ed08c46933..cd915e04e6 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -1093,6 +1093,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index cf3b208a90..3bbd0fc4d0 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 21f795eb2b..94667b1ef9 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index cc28964e61..dfd70cbc50 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -1087,6 +1087,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index e84f54c8fa..959acc3d46 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -1075,6 +1075,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index ef1cc46ff9..74add28657 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 3bae9db260..a526f0b460 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 607b0e07d3..b58197af33 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index a30445d8f2..57aa8aba08 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index 05ed95f564..54ac8a210b 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -1074,6 +1074,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index 1b40a7140e..6f95eeb038 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -1077,6 +1077,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index 04b9709cfe..59b501d3f2 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -1073,6 +1073,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index 012dfb2d8b..597200e4d4 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -1223,6 +1223,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 6f23422f97..282003412f 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -1220,6 +1220,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index c83123b8c9..8710be3493 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -1172,6 +1172,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 300feac108..65d7ad0d50 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -1171,6 +1171,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index 60bfa78216..b9a3a934dd 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -1183,6 +1183,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h index 953826df82..4611f67866 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h @@ -1170,6 +1170,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h index de9cb335fc..febbd51e84 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h @@ -1171,6 +1171,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index 4c8b404159..bea0dda156 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -1172,6 +1172,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h index b8dd1fe1b3..0b5f1c8f5b 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h @@ -1180,6 +1180,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 100 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index f10f446cc8..53ed5d677a 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -1175,6 +1175,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index c1c517c9d2..b5c7ca12e1 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -1174,6 +1174,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 08a340d0fb..35785ed3c7 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -1174,6 +1174,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index 7676f5ac03..2138aff729 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -1170,6 +1170,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index 28ee7e7709..0400661151 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -1170,6 +1170,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index 6cd10e617b..18e84cfcc1 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -1170,6 +1170,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index cc321686c3..aed0d50d0a 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -1170,6 +1170,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 38f7a9428b..bcf7fccbe2 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -1172,6 +1172,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index 3acb7dbd97..6359a553aa 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -1177,6 +1177,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index fe1896c3ae..28df3283b8 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -1172,6 +1172,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index 94836f1d40..ba4cd03861 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -1137,6 +1137,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 90c5ca270e..5df8276c85 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -1173,6 +1173,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index cfebd8c13b..463a8b1006 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -1172,6 +1172,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index d2905eb447..9d6c59c647 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -1171,6 +1171,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing #define DELAY_BEFORE_PROBING 375 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index f998b5d35f..4bd4a79c32 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -1174,6 +1174,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index e73dc88ab1..ac02344104 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -1193,6 +1193,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index cc1a5e8627..324b7d8bcb 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -1177,6 +1177,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 6aa5d4d20c..d8e2d44dc3 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 6e33fb3862..1cd7a9c249 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -1076,6 +1076,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index b308363afa..6a38c8dd6a 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -1080,6 +1080,13 @@ //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors +// Require minimum nozzle and/or bed temperature for probing +//#define PREHEAT_BEFORE_PROBING +#if ENABLED(PREHEAT_BEFORE_PROBING) + #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time + #define PROBING_BED_TEMP 50 +#endif + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 1