mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2025-07-07 06:57:39 -06:00
Scott Lahteine
parent
ccfdb80c1b
commit
bb03895ff8
650 changed files with 29146 additions and 23304 deletions
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -435,29 +435,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -490,23 +474,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -518,15 +507,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -541,6 +549,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -489,29 +489,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -544,23 +528,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -572,15 +561,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -595,6 +603,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -489,29 +489,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -544,23 +528,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -572,15 +561,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -595,6 +603,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 20
|
||||
#define TEMP_SENSOR_1 20
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 11
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -435,29 +435,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -490,23 +474,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -518,15 +507,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -541,6 +549,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -435,29 +435,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -490,23 +474,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -518,15 +507,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -541,6 +549,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -437,29 +437,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -492,23 +476,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -520,15 +509,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -543,6 +551,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -473,29 +473,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -528,23 +512,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -556,15 +545,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -579,6 +587,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -444,29 +444,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -499,23 +483,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -527,15 +516,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -550,6 +558,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -281,9 +281,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -584,6 +590,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 1
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 5
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -441,29 +441,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -496,23 +480,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -524,15 +513,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -547,6 +555,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -437,29 +437,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -492,23 +476,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -520,15 +509,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -543,6 +551,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -434,29 +434,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -489,23 +473,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -517,15 +506,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -540,6 +548,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
|
|
@ -442,29 +442,13 @@
|
|||
// @section temperature
|
||||
|
||||
/**
|
||||
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
|
||||
* Temperature Sensors:
|
||||
*
|
||||
* Temperature sensors available:
|
||||
*
|
||||
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
|
||||
* -------
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* Analog Themocouple Boards
|
||||
* -------
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
* NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 4.7kΩ pullup - Normal
|
||||
* -------
|
||||
* ================================================================
|
||||
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
|
||||
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
|
||||
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
|
||||
|
|
@ -497,23 +481,28 @@
|
|||
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
|
||||
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
|
||||
* 67 : 500kΩ SliceEngineering 450°C Thermistor
|
||||
* 68 : PT100 amplifier board from Dyze Design
|
||||
* 68 : PT100 Smplifier board from Dyze Design
|
||||
* 70 : 100kΩ bq Hephestos 2
|
||||
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
|
||||
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
|
||||
*
|
||||
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* ------- (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* Analog Thermistors - 1kΩ pullup
|
||||
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
|
||||
* (but gives greater accuracy and more stable PID)
|
||||
* ================================================================
|
||||
* 51 : 100kΩ EPCOS (1kΩ pullup)
|
||||
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
|
||||
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermistors - 10kΩ pullup - Atypical
|
||||
* -------
|
||||
* ================================================================
|
||||
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
|
||||
*
|
||||
* ================================================================
|
||||
* Analog RTDs (Pt100/Pt1000)
|
||||
* -------
|
||||
* ================================================================
|
||||
* 110 : Pt100 with 1kΩ pullup (atypical)
|
||||
* 147 : Pt100 with 4.7kΩ pullup
|
||||
* 1010 : Pt1000 with 1kΩ pullup (atypical)
|
||||
|
|
@ -525,15 +514,34 @@
|
|||
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
|
||||
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
|
||||
*
|
||||
* ================================================================
|
||||
* SPI RTD/Thermocouple Boards
|
||||
* ================================================================
|
||||
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
|
||||
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
|
||||
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
|
||||
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
|
||||
*
|
||||
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
|
||||
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
|
||||
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
|
||||
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
|
||||
*
|
||||
* ================================================================
|
||||
* Analog Thermocouple Boards
|
||||
* ================================================================
|
||||
* -4 : AD8495 with Thermocouple
|
||||
* -1 : AD595 with Thermocouple
|
||||
*
|
||||
* ================================================================
|
||||
* Custom/Dummy/Other Thermal Sensors
|
||||
* ------
|
||||
* ================================================================
|
||||
* 0 : not used
|
||||
* 1000 : Custom - Specify parameters in Configuration_adv.h
|
||||
*
|
||||
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*
|
||||
*/
|
||||
#define TEMP_SENSOR_0 70
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -548,6 +556,7 @@
|
|||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
#define TEMP_SENSOR_BOARD 0
|
||||
#define TEMP_SENSOR_SOC 0
|
||||
#define TEMP_SENSOR_REDUNDANT 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
|
|||
|
|
@ -276,9 +276,15 @@
|
|||
#define THERMAL_PROTECTION_BOARD // Halt the printer if the board sensor leaves the temp range below.
|
||||
#define BOARD_MINTEMP 8 // (°C)
|
||||
#define BOARD_MAXTEMP 70 // (°C)
|
||||
#ifndef TEMP_BOARD_PIN
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin, if not set in pins file.
|
||||
#endif
|
||||
//#define TEMP_BOARD_PIN -1 // Board temp sensor pin override.
|
||||
#endif
|
||||
|
||||
//
|
||||
// SoC Sensor options
|
||||
//
|
||||
#if TEMP_SENSOR_SOC
|
||||
#define THERMAL_PROTECTION_SOC // Halt the printer if the SoC sensor leaves the temp range below.
|
||||
#define SOC_MAXTEMP 85 // (°C)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -579,6 +585,9 @@
|
|||
// Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_BOARD_TEMP 40 // (°C) Turn on the fan if the board reaches this temperature
|
||||
|
||||
// Use TEMP_SENSOR_SOC as a trigger for enabling the controller fan
|
||||
//#define CONTROLLER_FAN_MIN_SOC_TEMP 40 // (°C) Turn on the fan if the SoC reaches this temperature
|
||||
|
||||
//#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings
|
||||
#if ENABLED(CONTROLLER_FAN_EDITABLE)
|
||||
#define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu
|
||||
|
|
|
|||
Some files were not shown because too many files have changed in this diff Show more
Loading…
Add table
Add a link
Reference in a new issue