mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2025-08-08 22:35:18 -06:00
Bring configs up to date, clean up
This commit is contained in:
Scott Lahteine
parent
bf072075f6
commit
baafcf125f
312 changed files with 382 additions and 10742 deletions
|
|
@ -812,7 +812,7 @@
|
|||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.4
|
||||
|
||||
#define TRAVEL_EXTRA_XYJERK 5.0 // Additional jerk allowance for all travel moves
|
||||
#define TRAVEL_EXTRA_XYJERK 5.0 // Additional jerk allowance for all travel moves
|
||||
|
||||
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
|
||||
#if ENABLED(LIMITED_JERK_EDITING)
|
||||
|
|
@ -1125,7 +1125,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
|
||||
|
||||
//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
|
||||
|
|
@ -1559,7 +1559,7 @@
|
|||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 5), (Y_MAX_POS - 5), 10 }
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 80 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1538,7 +1538,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1529,7 +1529,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1531,7 +1531,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1547,7 +1547,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1102,12 +1102,12 @@
|
|||
|
||||
#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
|
||||
|
||||
#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 0
|
||||
#define Z_HOMING_HEIGHT 0 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
|
||||
|
||||
#define Z_AFTER_HOMING 10
|
||||
//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
|
|
@ -1528,7 +1528,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 25
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 25 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -2267,13 +2267,13 @@
|
|||
#define NEOPIXEL_LED
|
||||
#if ENABLED(NEOPIXEL_LED)
|
||||
#define NEOPIXEL_TYPE NEO_GRB
|
||||
//#define NEOPIXEL_PIN 4 // LED driving pin
|
||||
//#define NEOPIXEL_PIN 4 // LED driving pin
|
||||
//#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
|
||||
//#define NEOPIXEL2_PIN 5
|
||||
#define NEOPIXEL_PIXELS 17
|
||||
//#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||
#define NEOPIXEL_BRIGHTNESS 255
|
||||
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||
//#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness (0-255)
|
||||
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||
|
||||
// Use a single Neopixel LED for static (background) lighting
|
||||
//#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
|
||||
|
|
|
|||
|
|
@ -1532,7 +1532,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1532,7 +1532,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1538,7 +1538,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1532,7 +1532,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1520,7 +1520,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1521,7 +1521,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1532,7 +1532,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1533,7 +1533,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1533,7 +1533,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1533,7 +1533,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1533,7 +1533,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1102,12 +1102,12 @@
|
|||
|
||||
#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
|
||||
|
||||
#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 0
|
||||
#define Z_HOMING_HEIGHT 0 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
|
||||
|
||||
#define Z_AFTER_HOMING 10
|
||||
//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
|
|
@ -1528,7 +1528,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 25
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 25 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -2266,14 +2266,14 @@
|
|||
// Support for Adafruit Neopixel LED driver
|
||||
#define NEOPIXEL_LED
|
||||
#if ENABLED(NEOPIXEL_LED)
|
||||
#define NEOPIXEL_TYPE NEO_GRBW
|
||||
//#define NEOPIXEL_PIN 4 // LED driving pin
|
||||
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||
//#define NEOPIXEL_PIN 4 // LED driving pin
|
||||
//#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
|
||||
//#define NEOPIXEL2_PIN 5
|
||||
#define NEOPIXEL_PIXELS 16
|
||||
//#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||
#define NEOPIXEL_BRIGHTNESS 255
|
||||
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||
//#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness (0-255)
|
||||
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||
|
||||
// Use a single Neopixel LED for static (background) lighting
|
||||
//#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use
|
||||
|
|
|
|||
|
|
@ -1538,7 +1538,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -1526,7 +1526,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
|
|
@ -2259,8 +2259,8 @@
|
|||
// Support for Adafruit Neopixel LED driver
|
||||
//#define NEOPIXEL_LED
|
||||
#if ENABLED(NEOPIXEL_LED)
|
||||
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||
//#define NEOPIXEL_PIN 4 // LED driving pin
|
||||
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||
//#define NEOPIXEL_PIN 4 // LED driving pin
|
||||
//#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
|
||||
//#define NEOPIXEL2_PIN 5
|
||||
#define NEOPIXEL_PIXELS 10 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
|
||||
|
|
|
|||
|
|
@ -1532,7 +1532,7 @@
|
|||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers)
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
|
|
@ -759,6 +759,7 @@
|
|||
#define Z_STEPPER_ALIGN_AMP 1.0 // Use a value > 1.0 NOTE: This may cause instability!
|
||||
#endif
|
||||
|
||||
// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
|
||||
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
|
||||
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
|
||||
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue