3D-printing/Configurations
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Configurations.git synced 2025-07-08 15:37:32 -06:00
Code Issues Projects Releases Packages Wiki Activity Actions

📝 Update Ender-5 S1 comments

Browse source
This commit is contained in:
Scott Lahteine 2024-01-04 15:16:39 -06:00
parent 3dd9093ee5
commit b9e1d1f5a0
2 changed files with 81 additions and 80 deletions
Download patch file Download diff file Expand all files Collapse all files

74
config/examples/Creality/Ender-5 S1/Configuration.h
View file

@ -471,29 +471,13 @@
// @section temperature // @section temperature
/** /**
* --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table * Temperature Sensors:
* *
* Temperature sensors available: * NORMAL IS 4.7kΩ PULLUP! Hotend sensors can use 1kΩ pullup with correct resistor and table.
*
* SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
* -------
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-2 and bed)
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-2 and bed)
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-2 and bed)
*
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
*
* Analog Themocouple Boards
* -------
* -4 : AD8495 with Thermocouple
* -1 : AD595 with Thermocouple
* *
* ================================================================
* Analog Thermistors - 4.7kΩ pullup - Normal * Analog Thermistors - 4.7kΩ pullup - Normal
* ------- * ================================================================
* 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors * 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
* 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA * 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
* 332 : 100kΩ Same as #1, but 3.3V scaled for DUE * 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
@ -519,6 +503,7 @@
* 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1% * 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
* 14 : 100kΩ (R25), 4092K (beta25), 4.7kΩ pull-up, bed thermistor as used in Ender-5 S1 * 14 : 100kΩ (R25), 4092K (beta25), 4.7kΩ pull-up, bed thermistor as used in Ender-5 S1
* 15 : 100kΩ Calibrated for JGAurora A5 hotend * 15 : 100kΩ Calibrated for JGAurora A5 hotend
* 17 : 100kΩ Dagoma NTC white thermistor
* 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327 * 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
* 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input * 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
* 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input * 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
@ -527,23 +512,29 @@
* 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950 * 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
* 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor * 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
* 67 : 500kΩ SliceEngineering 450°C Thermistor * 67 : 500kΩ SliceEngineering 450°C Thermistor
* 68 : PT100 amplifier board from Dyze Design * 68 : PT100 Smplifier board from Dyze Design
* 70 : 100kΩ bq Hephestos 2 * 70 : 100kΩ bq Hephestos 2
* 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32 * 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
* 666 : 200kΩ Einstart S custom thermistor with 10k pullup.
* 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor * 2000 : 100kΩ Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
* *
* Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ. * ================================================================
* ------- (but gives greater accuracy and more stable PID) * Analog Thermistors - 1kΩ pullup
* Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
* (but gives greater accuracy and more stable PID)
* ================================================================
* 51 : 100kΩ EPCOS (1kΩ pullup) * 51 : 100kΩ EPCOS (1kΩ pullup)
* 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup) * 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
* 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup) * 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
* *
* ================================================================
* Analog Thermistors - 10kΩ pullup - Atypical * Analog Thermistors - 10kΩ pullup - Atypical
* ------- * ================================================================
* 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor * 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
* *
* ================================================================
* Analog RTDs (Pt100/Pt1000) * Analog RTDs (Pt100/Pt1000)
* ------- * ================================================================
* 110 : Pt100 with 1kΩ pullup (atypical) * 110 : Pt100 with 1kΩ pullup (atypical)
* 147 : Pt100 with 4.7kΩ pullup * 147 : Pt100 with 4.7kΩ pullup
* 1010 : Pt1000 with 1kΩ pullup (atypical) * 1010 : Pt1000 with 1kΩ pullup (atypical)
@ -555,20 +546,39 @@
* NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C. * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
* 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
* *
* ================================================================
* SPI RTD/Thermocouple Boards
* ================================================================
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-2 and bed)
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-2 and bed)
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-2 and bed)
*
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
* Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
* Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
*
* ================================================================
* Analog Thermocouple Boards
* ================================================================
* -4 : AD8495 with Thermocouple
* -1 : AD595 with Thermocouple
*
* ================================================================
* SoC internal sensor * SoC internal sensor
* ================================================================ * ================================================================
* 100 : SoC internal sensor * 100 : SoC internal sensor
* *
* ================================================================ * ================================================================
* Custom/Dummy/Other Thermal Sensors * Custom/Dummy/Other Thermal Sensors
* ------ * ================================================================
* 0 : not used * 0 : not used
* 1000 : Custom - Specify parameters in Configuration_adv.h * 1000 : Custom - Specify parameters in Configuration_adv.h
* *
* !!! Use these for Testing or Development purposes. NEVER for production machine. !!! * !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
*
*/ */
#define TEMP_SENSOR_0 1 #define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0 #define TEMP_SENSOR_1 0
@ -797,7 +807,7 @@
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 10.00 #define DEFAULT_bedKp 10.00
#define DEFAULT_bedKi 0.023 #define DEFAULT_bedKi .023
#define DEFAULT_bedKd 305.4 #define DEFAULT_bedKd 305.4
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
@ -856,7 +866,7 @@
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER) #if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
//当前温度和目标温度相差多少度 才开始PID算法控制温度。 Rock_20220916 // The current temperature and target temperature differences start to control the temperature of the PID algorithm. Rock_20220916
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
@ -1710,7 +1720,6 @@
#define Z_PROBE_ERROR_TOLERANCE 3 // (mm) Tolerance for early trigger (<= -probe.offset.z + ZPET) #define Z_PROBE_ERROR_TOLERANCE 3 // (mm) Tolerance for early trigger (<= -probe.offset.z + ZPET)
//#define Z_AFTER_PROBING 5 // (mm) Z position after probing is done //#define Z_AFTER_PROBING 5 // (mm) Z position after probing is done
// (Changed from -2 to -5)
#define Z_PROBE_LOW_POINT -5 // (mm) Farthest distance below the trigger-point to go before stopping #define Z_PROBE_LOW_POINT -5 // (mm) Farthest distance below the trigger-point to go before stopping
// For M851 provide ranges for adjusting the X, Y, and Z probe offsets // For M851 provide ranges for adjusting the X, Y, and Z probe offsets
@ -3108,11 +3117,6 @@
// Over-the-air Firmware Update with M936 // Over-the-air Firmware Update with M936
#define OTA_FIRMWARE_UPDATE #define OTA_FIRMWARE_UPDATE
//
// Creality V4.2.5 display. Creality board but retain the display.
//
#define RET6_12864_LCD
// //
// Ender-2 OEM display, a variant of the MKS_MINI_12864 // Ender-2 OEM display, a variant of the MKS_MINI_12864
// //

5
config/examples/Creality/Ender-5 S1/Configuration_adv.h
View file

@ -684,9 +684,7 @@
* Multiple extruders can be assigned to the same pin in which case * Multiple extruders can be assigned to the same pin in which case
* the fan will turn on when any selected extruder is above the threshold. * the fan will turn on when any selected extruder is above the threshold.
*/ */
//视新板子是用哪个管脚来接风扇，比如为PAx，则在Configuration_adv.h中定义#define E0_AUTO_FAN_PIN PAx即可。 #define E0_AUTO_FAN_PIN PC0 // According to the new hardware schematic diagram PC0 is connected to the heatsink fan
//按新硬件原理图，假设用PC0接喉管风扇，改为#define E0_AUTO_FAN_PIN PC0，当喉管温度大于EXTRUDER_AUTO_FAN_TEMPERATURE时喉管风扇开启 --zy
#define E0_AUTO_FAN_PIN PC0
#define E1_AUTO_FAN_PIN -1 #define E1_AUTO_FAN_PIN -1
#define E2_AUTO_FAN_PIN -1 #define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1 #define E3_AUTO_FAN_PIN -1
@ -1554,7 +1552,6 @@
* Axis moves <= 1/2 the axis length and Extruder moves <= EXTRUDE_MAXLENGTH * Axis moves <= 1/2 the axis length and Extruder moves <= EXTRUDE_MAXLENGTH
* will be shown in the move submenus. * will be shown in the move submenus.
*/ */
#define MANUAL_MOVE_DISTANCE_MM 10, 1.0, 0.1 // (mm) #define MANUAL_MOVE_DISTANCE_MM 10, 1.0, 0.1 // (mm)
//#define MANUAL_MOVE_DISTANCE_MM 100, 50, 10, 1.0, 0.1 // (mm) //#define MANUAL_MOVE_DISTANCE_MM 100, 50, 10, 1.0, 0.1 // (mm)
//#define MANUAL_MOVE_DISTANCE_MM 500, 100, 50, 10, 1.0, 0.1 // (mm) //#define MANUAL_MOVE_DISTANCE_MM 500, 100, 50, 10, 1.0, 0.1 // (mm)