✨ MAG_MOUNTED_PROBE

MarlinFirmware/Marlin#24420

config/default/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/default/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -1347,6 +1347,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -1414,6 +1414,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -1328,6 +1328,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Alfawise/U20/Configuration.h

@@ -1415,6 +1415,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Alfawise/U20/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AliExpress/CL-260/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -1346,6 +1346,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/A2/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/A2/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/A2plus/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/A2plus/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/A6/Configuration.h

@@ -1362,6 +1362,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/A6/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/A8/Configuration.h

@@ -1348,6 +1348,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/A8/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/A8plus/Configuration.h

@@ -1347,6 +1347,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/A8plus/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/A9/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/A9/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/E10/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/E10/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/E16/BTT SKR 1.3/Configuration.h

@@ -1347,6 +1347,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/E16/Stock/Configuration.h

@@ -1347,6 +1347,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/E16/Stock/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET4+/Configuration.h

@@ -1351,6 +1351,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET4+/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET4-Pro/Configuration.h

@@ -1351,6 +1351,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET4-Pro/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET4/Configuration.h

@@ -1351,6 +1351,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET4/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET4X/Configuration.h

@@ -1351,6 +1351,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET4X/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET5-Pro/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET5-Pro/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET5/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET5/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Anet/ET5X/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Anet/ET5X/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AnyCubic/Chiron/Configuration.h

@@ -1349,6 +1349,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AnyCubic/Chiron/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h

@@ -1347,6 +1347,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h

@@ -1347,6 +1347,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AnyCubic/i3 Mega/Configuration.h

@@ -1372,6 +1372,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AnyCubic/i3 Mega/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/AnyCubic/i3/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/ArmEd/Configuration.h

@@ -1346,6 +1346,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/ArmEd/Configuration_adv.h

@@ -1324,6 +1324,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Genius Pro/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Genius Pro/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Genius/BLTouch/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Genius/BLTouch/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Genius/V1/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Genius/V1/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Hornet/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Hornet/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h

@@ -1361,6 +1361,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Sidewinder X1/V1/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Artillery/Sidewinder X2/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/Artillery/Sidewinder X2/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/Azteeg/X5GT/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BIBO/TouchX/default/Configuration.h

@@ -1301,6 +1301,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -1312,6 +1312,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BIQU/B1 - SKR 1.4/Configuration.h

@@ -1354,6 +1354,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIQU/B1 - SKR 1.4/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BIQU/B1 - SKR 2/Configuration.h

@@ -1354,6 +1354,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIQU/B1 - SKR 2/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BIQU/B1 SE Plus/Configuration.h

@@ -1343,6 +1343,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIQU/B1 SE Plus/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BIQU/BX/Configuration.h

@@ -1350,6 +1350,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIQU/BX/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BIQU/Thunder Standard/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BIQU/Thunder Standard/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BQ/Hephestos/Configuration.h

@@ -1346,6 +1346,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BQ/Hephestos_2/Configuration.h

@@ -1359,6 +1359,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -1327,6 +1327,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/BQ/WITBOX/Configuration.h

@@ -1346,6 +1346,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/CTC/A13/Configuration.h

@@ -1346,6 +1346,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/CTC/A13/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu

config/examples/CTC/Bizer/Configuration.h

@@ -1345,6 +1345,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR

config/examples/CTC/Bizer/Configuration_adv.h

@@ -1319,6 +1319,9 @@
       #define XATC_Y_POSITION Y_CENTER      // (mm) Y position to probe
       #define XATC_Z_OFFSETS { 0, 0, 0 }    // Z offsets for X axis sample points
     #endif
+
+    // Show Deploy / Stow Probe options in the Motion menu.
+    #define PROBE_DEPLOY_STOW_MENU
   #endif
 
   // Include a page of printer information in the LCD Main Menu