✨ MakerBot Replicator (2012) Single+Dual (#1147)

config/examples/MakerBot/Replicator Dual/README.md

@@ -0,0 +1,41 @@
+# Space Issues
+## Version Differences
+ - The single extruder build enables the `S_CURVE_ACCELERATION` feature due to extra available space.
+ - The dual extruder build enables `MARLIN_SMALL_BUILD` to match feature parity with the single extruder build with exception to `S_CURVE_ACCELERATION`.
+
+## Features disabled/enabled to save space.
+```
+AUTOTEMP
+SDCARD_READONLY
+NO_SD_AUTOSTART
+ARC_SUPPORT
+NO_VOLUMETRICS
+NO_WORKSPACE_OFFSETS
+```
+
+## Fitting S_CURVE_ACCELERATION in the dual build.
+Removing `BABYSTEPPING` entirely will allow `S_CURVE_ACCELERATION` to fit on dual extruder builds. However commenting out `DOUBLECLICK_FOR_Z_BABYSTEPPING`, `BABYSTEP_DISPLAY_TOTAL`, and `CONFIGURE_FILAMENT_CHANGE` will fit `S_CURVE_ACCELERATION` without entirely losing `BABYSTEPPING`.
+
+# Flashing
+## USB Flashing
+MakerBot's Mightyboard Rev E’s are missing capacitor c20. This prevents the board from self resetting to flash over USB. You can try to time pressing the reset button with uploading firmware. I have only ever accomplished this once.
+
+## ICSP Flashing
+I find it much easier to flash over the ICSP header using an Arduino and AVR Dude. Adjust settings as necessary such as the port or if you are using a different device to flash. Feel free to reach out to the author of this config in Discord for help.\
+`avrdude -v -patmega1280 -cstk500v1 -PCOM4 -b19200 -U flash:w:firmware.hex`
+
+# Printer Information
+## Primary Extruder (Dual)
+The right nozzle is Extruder 1 (E0) on this printer which will often be confusing as it will be the left temperature on the screen. There are a couple of ways to change this, you can pin swap the pins file. Don’t forget to invert the motor direction. It is possible but not as easy to edit the display order instead.
+
+## Motor Current
+The FlashForge Creator Pro example sets current a little higher at .84 for XY&E and .4 for Z. I have matched the MakerBot values from beta.ivc.no of .81 except for Z rounding from .278 to .28. The Z motor will whine more at higher current.
+
+# Modifications
+
+## Part Cooling Fan
+If you have added a part cooling fan to the extra mosfet you need to uncomment #define NUM_M106_FANS\
+`#define NUM_M106_FANS 1`
+
+You will also need to set the pin definition. This can actually be inserted right below the line you just uncommented.\
+`#define FAN0_PIN                  MOSFET_F_PIN`

config/examples/MakerBot/Replicator Single/README.md

@@ -0,0 +1,41 @@
+# Space Issues
+## Version Differences
+ - The single extruder build enables the `S_CURVE_ACCELERATION` feature due to extra available space.
+ - The dual extruder build enables `MARLIN_SMALL_BUILD` to match feature parity with the single extruder build with exception to `S_CURVE_ACCELERATION`.
+
+## Features disabled/enabled to save space.
+```
+AUTOTEMP
+SDCARD_READONLY
+NO_SD_AUTOSTART
+ARC_SUPPORT
+NO_VOLUMETRICS
+NO_WORKSPACE_OFFSETS
+```
+
+## Fitting S_CURVE_ACCELERATION in the dual build.
+Removing `BABYSTEPPING` entirely will allow `S_CURVE_ACCELERATION` to fit on dual extruder builds. However commenting out `DOUBLECLICK_FOR_Z_BABYSTEPPING`, `BABYSTEP_DISPLAY_TOTAL`, and `CONFIGURE_FILAMENT_CHANGE` will fit `S_CURVE_ACCELERATION` without entirely losing `BABYSTEPPING`.
+
+# Flashing
+## USB Flashing
+MakerBot's Mightyboard Rev E’s are missing capacitor c20. This prevents the board from self resetting to flash over USB. You can try to time pressing the reset button with uploading firmware. I have only ever accomplished this once.
+
+## ICSP Flashing
+I find it much easier to flash over the ICSP header using an Arduino and AVR Dude. Adjust settings as necessary such as the port or if you are using a different device to flash. Feel free to reach out to the author of this config in Discord for help.\
+`avrdude -v -patmega1280 -cstk500v1 -PCOM4 -b19200 -U flash:w:firmware.hex`
+
+# Printer Information
+## Primary Extruder (Dual)
+The right nozzle is Extruder 1 (E0) on this printer which will often be confusing as it will be the left temperature on the screen. There are a couple of ways to change this, you can pin swap the pins file. Don’t forget to invert the motor direction. It is possible but not as easy to edit the display order instead.
+
+## Motor Current
+The FlashForge Creator Pro example sets current a little higher at .84 for XY&E and .4 for Z. I have matched the MakerBot values from beta.ivc.no of .81 except for Z rounding from .278 to .28. The Z motor will whine more at higher current.
+
+# Modifications
+
+## Part Cooling Fan
+If you have added a part cooling fan to the extra mosfet you need to uncomment #define NUM_M106_FANS\
+`#define NUM_M106_FANS 1`
+
+You will also need to set the pin definition. This can actually be inserted right below the line you just uncommented.\
+`#define FAN0_PIN                  MOSFET_F_PIN`