diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 6cac225fce..df99f8b676 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,9 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. - * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ //#define SERIAL_PORT_2 -1 @@ -363,6 +361,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 6149864ab4..370fbaf6ec 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -338,15 +338,22 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. + * */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index e86b78830d..89008bd052 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -100,6 +100,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -108,8 +109,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 648360827d..86d0693983 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 7 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 127 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 7 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 127 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index ed97fa2726..72cce535d7 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index 42a4349264..1cf4453ba9 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index ce3d7335a0..6e309410d8 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index 726218fd77..ac881a09c2 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 338e8f2a58..eba07057e8 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 724acb1696..4fcecf0db2 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 130 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 130 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index 38a26e24ee..d3d34da673 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -124,6 +124,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -132,8 +133,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -401,6 +400,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index a1165e871b..08501de4b3 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index efffbf541f..0d3ba8fc84 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -124,6 +124,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -132,8 +133,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -401,6 +400,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index 01117f3998..b2e0682e35 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 11876ded68..26c8c75315 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 721c18e334..440f33b5cc 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index ffc1395c90..057f0f8a7c 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index 86c9e3092c..adee18d38a 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 0dc3e95d6e..15c2df0301 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index e18b849a25..90a0c35db1 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 0dc3e95d6e..15c2df0301 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index d7e8ba4f2a..d6eab653a5 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 50b3a4afac..e7e96388c9 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index b06c627eb5..e400ceec2c 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 393c2c3ec3..1b971be8ff 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 7040e47282..dad546fba3 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index fb86f1a9ac..8f2d3cd7c9 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index ad56074f44..261fbffeaa 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index db9019630f..2bf3b11c5a 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h index 231f6f49d3..0794d8ae27 100644 --- a/config/examples/Anet/E16/Configuration.h +++ b/config/examples/Anet/E16/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index 2bf805c215..23644b1918 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 58f0985a29..d25a0cb4fc 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 95fc0e1e42..256895df47 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 7 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 7 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 8ec77c6262..fe944476bc 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index c3a60abf94..3656ed49e0 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -342,15 +342,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Artillery/Genius/Configuration.h b/config/examples/Artillery/Genius/Configuration.h index 599885c10c..c5bdd769f9 100644 --- a/config/examples/Artillery/Genius/Configuration.h +++ b/config/examples/Artillery/Genius/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h index 7742687887..183049dd63 100755 --- a/config/examples/Artillery/Genius/Configuration_adv.h +++ b/config/examples/Artillery/Genius/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Artillery/Sidewinder X1/Configuration.h b/config/examples/Artillery/Sidewinder X1/Configuration.h index ee29f512a4..584de7183d 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h index 7742687887..183049dd63 100755 --- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index bd4ead3cdc..17f432794f 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index f23500da4b..2349a9bd5c 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index bf6fd7d47e..b62881faba 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 331b636b37..7c5e4aa99c 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index c4f0eaaaf7..83c8880758 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 6f615cc0ba..95e1e03099 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index bc2362a429..f5497264df 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index c82558f225..62d56c59b4 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -107,6 +107,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -115,8 +116,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -371,6 +370,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index 6211423bc0..7851507df4 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index b7e428feef..ba81ddce2e 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index bc2362a429..f5497264df 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h index 2152802582..6099ea75cc 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h index 04a2615174..50833272da 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h index 16461c6c62..f25f73e356 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h index 46013816c3..3b618075f6 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index 97b2cd06a9..1cce56aa1a 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 5c8f36c874..38719411e6 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h index 22c48ebb4f..ba35f5b8e3 100644 --- a/config/examples/Creality/CR-10/Configuration.h +++ b/config/examples/Creality/CR-10/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index 188fad16e5..f81b0440f2 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h index 9632f54722..cba8e13a30 100644 --- a/config/examples/Creality/CR-10S/Configuration.h +++ b/config/examples/Creality/CR-10S/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index e076b061e6..db6c1fa2f0 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h index 571739c868..d7801abc3e 100644 --- a/config/examples/Creality/CR-10_5S/Configuration.h +++ b/config/examples/Creality/CR-10_5S/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index 2d4e361bf4..fa65664862 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h index dd78052fe7..98928ea4ce 100644 --- a/config/examples/Creality/CR-10mini/Configuration.h +++ b/config/examples/Creality/CR-10mini/Configuration.h @@ -108,6 +108,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -116,8 +117,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -372,6 +371,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index c2b970e763..652238b83b 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index f909553f87..8416352761 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 20692abc93..0c3f4093b3 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index c7ab824e3a..fe189a864d 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 517d0bc9ce..48dab4ba7e 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 007d928f6b..21fc7c7ad1 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 4fafd95411..efbd222005 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 4e3a319dff..f68ebd2c7d 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 9b14d5a6eb..530c935167 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h index 2c529587bf..4b15c30ca8 100644 --- a/config/examples/Creality/Ender-3/Configuration.h +++ b/config/examples/Creality/Ender-3/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index 6f5409627e..b83a699b47 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index a7583df906..49ac7c5d03 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index d84e781ff9..5dc85ed88b 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/Ender-5 Pro/Configuration.h b/config/examples/Creality/Ender-5 Pro/Configuration.h index d4d2ab4f59..a0c06f8fa6 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h index 9cec0eeec6..a42828a2f4 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Creality/Ender-5/Configuration.h b/config/examples/Creality/Ender-5/Configuration.h index 4deea6a316..dc46794f0a 100644 --- a/config/examples/Creality/Ender-5/Configuration.h +++ b/config/examples/Creality/Ender-5/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h index ca59cc60a5..06395d3dc6 100644 --- a/config/examples/Creality/Ender-5/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 0bddae07fc..8c7a5cd997 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index abd011df9d..23336550cf 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 993ee12556..de4a916333 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index cd6eeca9ac..9d8fe2cf44 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 773abf87dd..29d24bba1d 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 461567715a..ac7460a548 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index b107b7f45b..8537e68f69 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 8e292bfd66..581dcbd471 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h index 5d9483ec95..12d9069a91 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h index ac3c9237be..eb951594bb 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h index f9b937944b..f9b8207b0e 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h index ac3c9237be..eb951594bb 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h index 74f3a4b90d..e5c8fc638e 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h index ac3c9237be..eb951594bb 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/Cheetah/base/Configuration.h b/config/examples/FYSETC/Cheetah/base/Configuration.h index d7d82807a3..838a9b4727 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h index ac3c9237be..eb951594bb 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 63eec24e09..e7fcfc3c81 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -365,6 +364,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index 87a4c33c52..29295b3ba6 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index aae502400c..3883c9f988 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index a2bb91f00b..f7b1397c7d 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 2dc72958d6..61fd80971c 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index 90eae9f37b..e0af15564f 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index 9d0b7ca621..3063654d86 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index 90eae9f37b..e0af15564f 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index e79156f48d..4226030377 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 1bceb923d7..ff086f0664 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 7880987d29..24923fe7f7 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index a1272ebd18..22f1710f74 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 737af641f6..d88ac2103a 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -140,6 +140,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -148,8 +149,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -404,6 +403,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 386ba8f35d..3759ea9f14 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 0605f6cc05..0af2107ade 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -367,6 +368,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) @@ -488,10 +490,10 @@ #define PID_FUNCTIONAL_RANGE 8 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. -/* +/* * For Roxy Formbot T-Rex2 Frankenstien dmachine: * - + >>> M303 S210 E0 C5 U1 SENDING:M303 S210 E0 C5 U1 PID Autotune start diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 127e715666..88b657a3d6 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -340,7 +340,6 @@ * * The fan turns on automatically whenever any driver is enabled and turns * off (or reduces to idle speed) shortly after drivers are turned off. - * */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) @@ -348,9 +347,9 @@ //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled - #define CONTROLLERFAN_SPEED_IDLE 30 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors - #define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings #if ENABLED(CONTROLLER_FAN_EDITABLE) #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu #endif diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index 093aa7d835..2ea0a21c74 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -103,6 +103,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -111,8 +112,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -367,6 +366,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index 887f0dac38..05d09cef7e 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index 4e1a3caf7b..4b8bd0e8c1 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 3cd164e29d..229739f336 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index 9e466b294a..4329b6ef23 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index 1cf6d97cbe..0937d95163 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index 53d9203c0a..d4f8c6812d 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 50d898aeab..0d2d6de1da 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A10T/Configuration.h b/config/examples/Geeetech/A10T/Configuration.h index 928fa16d15..1e44b46c2c 100644 --- a/config/examples/Geeetech/A10T/Configuration.h +++ b/config/examples/Geeetech/A10T/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h index 50d898aeab..0d2d6de1da 100644 --- a/config/examples/Geeetech/A10T/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index ae61fa29cd..4cf39f1782 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index 10afef2ea8..5594f7feff 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 42488d65e8..510534cbb7 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 10afef2ea8..5594f7feff 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index 3d148f66b0..ec09ff2a0e 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index 10afef2ea8..5594f7feff 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 9c8ad770a4..e35e96bd4c 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 3a0d5838ba..cd4f487f62 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index ac27c83a2d..6d16fab7b1 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 02f6242cc0..0bd8f4179e 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index 0a826690df..4cd2a0bc81 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index a2bb91f00b..f7b1397c7d 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index 29d9edf06e..18bc1e979f 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index 3a0d5838ba..cd4f487f62 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index e925e0458c..88ad8be0cd 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index c2e22fbbf2..6760c43257 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index f4d7edbeb9..0051435a66 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 02f6242cc0..0bd8f4179e 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 1df8059bae..9ffbd2be48 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 1cfcb5dbb8..c8992f1a86 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index e405049809..698c5ea909 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index a2bb91f00b..f7b1397c7d 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 7f8f82a1df..e441f58119 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index a2bb91f00b..f7b1397c7d 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index cfff10049f..822f4cb494 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index 07e27689c6..dcf69e7343 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 2b14df8b3f..5cf06e7c69 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 649da2ef8f..0823fe77c5 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index a89a58aed3..e13a52d96d 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 3cd164e29d..229739f336 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 27a13ef1c9..b680654a43 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 3cd164e29d..229739f336 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 29c8d15606..db54c97061 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index f89aca1491..3e5bff9901 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -338,14 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 649094424b..2115ff0045 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 15a6b0ec14..9245aed3f0 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index b7e70a71e8..5ce70c2966 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -100,6 +100,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -108,8 +109,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index fd627343c3..f99d5c5ac7 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -343,15 +343,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index e036291531..f81f1445fc 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -104,6 +104,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -112,8 +113,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -368,6 +367,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index bff7539bc8..10fa5ab631 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index 6c0c3094eb..4b7a426cf9 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -100,6 +100,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -108,8 +109,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index fd627343c3..f99d5c5ac7 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -343,15 +343,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index db19033928..3f31120289 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 0e727e4dd4..3edb45447d 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration.h b/config/examples/MakerFarm/Pegasus_12/Configuration.h index b41db7f0e4..d49eb7b5cb 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h index fe1b9d8017..461bae0f1a 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 6460a75103..beea9b372b 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index f2ce4fc1a6..65b38d5596 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 6d1f932cd0..139b68b944 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -104,6 +104,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -112,8 +113,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -368,6 +367,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index bdfdf21ad0..9c13fc64e1 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index ffd0c34413..a8a3b39a81 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index ea738605bc..fee48fadf5 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN // Malyan M200: uncomment if you use FAN2 to cool the board (original) #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN MALYAN_FAN2_PIN // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN MALYAN_FAN2_PIN // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 1810040629..22b74ccffe 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index eee641118a..ba26fa1566 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 39995417d1..2e5a2fe5d8 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index bdb53eb08d..14fbfa1b1a 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index bd53e19065..ab5910b7c3 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index 53fbcb0055..e6075272d8 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -370,6 +369,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index 590027c967..9b367c3aa5 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -369,6 +368,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index 9f5b950d30..567fb83a87 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 91b6f77a96..e24b07cfad 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index 9ea684012d..5caf92643b 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 5ac91969ab..6f7ad7c349 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index 2e44d8bb19..a9b412af72 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -364,6 +363,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index b1f60ee667..889f298fd8 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 12d03378a1..686fd08892 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index b5758e4453..704133a24e 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -366,6 +365,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 8efb7d26eb..7688b7347f 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index a32ca4840e..944554a21a 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -366,6 +365,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index 8efb7d26eb..7688b7347f 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 89203cd1f3..8d79d9e313 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -366,6 +365,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index 8efb7d26eb..7688b7347f 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index d282cbc358..63f7f6fa8d 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index ea82945248..88484d150f 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index c7115481b1..8c0a9eb412 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -366,6 +365,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 2adf52acf7..2ef702e197 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 4 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 4 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 6c2ec26c03..9b0f1eb5ac 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -139,6 +139,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -147,8 +148,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -403,6 +402,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index 416c3ba9f3..417bd0ad30 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 0d6b8e5f86..11919a45cf 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -139,6 +139,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -147,8 +148,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -403,6 +402,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index 08d5f837ab..177ca76779 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index b1f2a401ad..549aa024fb 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 55a5901fc5..f367ad2cfe 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index 0b76ec8fd0..ea8cfec90b 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 8a3e80d3ce..a7419c4c2c 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h index 8c32674738..6c862aaf8a 100644 --- a/config/examples/STM32/stm32f103ret6/Configuration.h +++ b/config/examples/STM32/stm32f103ret6/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index dc842f1cca..78d33bd20d 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 5426a9d2b7..9a306b23b3 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index cc624723b3..ef76068bfa 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index 559e5fb522..3c2c767a1c 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 6bd44bea54..1cb513acde 100755 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index f3bbba172f..3d5a35ae51 100755 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index e2306383c4..d5782fe4ec 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 0305b24918..8d3fe680fa 100755 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 7656667206..acbb0a5339 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 1141fe282d..428b3afe68 100755 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index a826b47380..fd23cf74f9 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 1141fe282d..428b3afe68 100755 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 6958be7a11..8b79e5bad6 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index 991339fee5..7cb2141d04 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 3f5fce66a4..9efbaaed09 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -115,6 +115,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -123,8 +124,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -385,6 +384,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 9d77f092e0..c66f123e39 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 1016fabcb7..41685fe186 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index f19f53d085..20716e7656 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 2d00403e26..2038764039 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index bbdad88fb3..566fa910cb 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -365,6 +364,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index a0e85f6030..8750f44f24 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 6687b8a073..26e814b36e 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index a4868d721a..41dd6fc50a 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 4eba112fc2..ee9f613232 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index 691716f712..035e039fdb 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index 837b9fb5ec..d2ed84444f 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index 7dc69aecc6..ece769d4de 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 6e813fbcd2..fbb964ea55 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index a9cc7f07a6..6cdc07ec2c 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index dc026416c4..6aa9a5245c 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -115,6 +115,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -123,8 +124,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -383,6 +382,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index 6fb57ca32c..2053c3bc6b 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -351,15 +351,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index a177c4c73b..13b2b6f283 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index cb4fcef764..355f815576 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 55b6b3396b..325f9e75e0 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index cb4fcef764..355f815576 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 3fef9f0a9a..71eadab268 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -376,6 +375,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 48eb6e4794..8024251309 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 725e45f3b6..f32869dc81 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 9dd6719bcd..e30fb84e2c 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 5939550331..d7350d0646 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index 6d8584fafe..618c461c88 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 516b79995a..66193f739e 100755 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index ed6f0a9ba1..f744a42d62 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index 866a4ea915..1c9d311ca4 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 4c04ae002c..8c3e5b1b2c 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -114,6 +114,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -122,8 +123,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -378,6 +377,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index dca3b10193..a5e44993f8 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 50b6c9a87e..362061e57c 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index 87212b15a5..fbf22d1f94 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index c4b447f3c9..8239a6171e 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index c0a5240ecc..3755331354 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index fbd034d696..1d62d321b2 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index 497948bbd6..a250587fae 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index b5aa3d190c..a33ff16b05 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 8f2b0060f4..223326290c 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index 216733e597..35d87f5c8d 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 8f2b0060f4..223326290c 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 8dd46a4a7e..f735d94940 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 2c2e9383c4..cc89eb5fe5 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index 8f09db6553..8f49715cc6 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index 63140d0770..c35c2d873f 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index 8fa3593d69..8727b69674 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index b703d6ec63..b17da24e65 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index d96e38a2b8..71b0a68bf1 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index b703d6ec63..b17da24e65 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index d96e38a2b8..71b0a68bf1 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index b703d6ec63..b17da24e65 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 08150d4198..da7284fd7d 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index f4c8fa0798..05290a15e4 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index aef22b2b6f..f27e895214 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -104,6 +104,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -112,8 +113,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -368,6 +367,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 7d51e5000b..78809ce628 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index af12109444..79beb93305 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 6e669bf976..0711c9963d 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index b919ca5d94..8d01dc1f4d 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 05d7fff5c5..f4c3a2c03b 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 2c2e9383c4..cc89eb5fe5 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index 8faf3be833..9cf80fcf10 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 407539b471..39fbf413bc 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index 4f91fa5e61..223761f8af 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 2c2e9383c4..cc89eb5fe5 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index d3cb627072..03d7273aaf 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -103,6 +103,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -111,8 +112,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -367,6 +366,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 4f626b8d77..c5df401b03 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 316682015e..295862b427 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 2d4f73dffc..c79ea867b5 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -368,6 +367,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 0ae6b57c68..59803cf8b5 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index fbd698d689..26a367edf6 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 6d514e550c..e69e3a4343 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index e76322acd8..aff14f1559 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 5a68a64627..110a9a37ff 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ #define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - #define CONTROLLER_FAN_PIN 23 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + #define CONTROLLER_FAN_PIN 23 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h index a1da1c8a69..378e2535bb 100644 --- a/config/examples/wt150/Configuration.h +++ b/config/examples/wt150/Configuration.h @@ -99,6 +99,7 @@ /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] @@ -107,8 +108,6 @@ /** * Select a secondary serial port on the board to use for communication with the host. - * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port -1 is the USB emulated serial port, if available. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ @@ -363,6 +362,7 @@ * 331 : (3.3V scaled thermistor 1 table for MEGA) * 332 : (3.3V scaled thermistor 1 table for DUE) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 202 : 200k thermistor - Copymaster 3D * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index 44cf9d4daa..3435205279 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -338,15 +338,21 @@ * Controller Fan * To cool down the stepper drivers and MOSFETs. * - * The fan will turn on automatically whenever any stepper is enabled - * and turn off after a set period after all steppers are turned off. + * The fan turns on automatically whenever any driver is enabled and turns + * off (or reduces to idle speed) shortly after drivers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan - #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled - #define CONTROLLERFAN_SPEED 255 // 255 == full speed - //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered + #define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.) + #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled + #define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled + #define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors + //#define CONTROLLER_FAN_EDITABLE // Enable M710 configurable settings + #if ENABLED(CONTROLLER_FAN_EDITABLE) + #define CONTROLLER_FAN_MENU // Enable the Controller Fan submenu + #endif #endif // When first starting the main fan, run it at full speed for the