diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index ca4f86a834..c9e226cef4 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -1044,7 +1044,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1172,18 +1172,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1260,6 +1258,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index c1e545c27f..97bf486c94 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index 815863ecc1..88ad8b347b 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 28 // Pin to detect power loss + //#define POWER_LOSS_PIN 28 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index 57fd9d73a4..09a38f51a3 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 738b24ea31..c0e414e8c6 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index be5e1f9634..eecdd7ad14 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -1052,7 +1052,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1180,18 +1180,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1268,6 +1266,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index 8194b834c9..89eab57253 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index 014b452606..3fde79da51 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 4722fba3f6..463c554772 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 4722fba3f6..463c554772 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index f98f9579c9..ff9f7c7daf 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 85f0b4866d..7dec288079 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index 58375a2700..f45835455a 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index 16eff9b2c8..06ce83b050 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating //#define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index 2fb0bd76c0..8b7ce3700a 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 580e110257..be8f72b54e 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index dd3bb5588e..1be2ea6e5c 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -1055,7 +1055,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1183,18 +1183,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1271,6 +1269,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h index 556ee9e1f4..670d5b606a 100755 --- a/config/examples/Artillery/Genius/Configuration_adv.h +++ b/config/examples/Artillery/Genius/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h index 556ee9e1f4..670d5b606a 100755 --- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 6c1582efff..96115ba1f6 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 66ca939320..3ec00cf0b9 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index 0b33f18b68..1dc813cc19 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index 70811d98ae..71ccee89ac 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -1059,7 +1059,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1187,18 +1187,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1275,6 +1273,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index 0b33f18b68..1dc813cc19 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h index 27ffdf28dc..87d2378878 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1267,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h index e1c80facee..95af2bf57a 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1267,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 5b96dc75ec..c96fb1127b 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index 9a4c53c6e5..a0b044706a 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index 8588be2b20..2d17a21990 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index 60bc350e20..f604950207 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index 9030d22ada..35c66f9d1b 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 765685b082..d7685b01f7 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 21fb0b08d0..5c925055f2 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index f7306dd396..d70dcbc9b1 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 71b23974b6..ddeee23a96 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index 59bb0a8953..3ace3fa4dd 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index ac375e6e6f..62242ebd11 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h index 50e32abbcf..d5f50bc712 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h index aa31918997..ed9f21d3ab 100644 --- a/config/examples/Creality/Ender-5/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 70c11c7e0b..1d93a52cd9 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index 867bcf7530..1f582b9a0d 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' #define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ //#define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating //#define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating //#define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 4c70a88325..b347be484d 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 26fce6c3af..5c9a44b18d 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h index eb1fb2329f..14736422b3 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h index eb1fb2329f..14736422b3 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h index eb1fb2329f..14736422b3 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h index eb1fb2329f..14736422b3 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index f633d83479..b23d005286 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index ca13559170..a4e1049cbe 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index a06b849b17..bdac723a12 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index a06b849b17..bdac723a12 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index b3dc197de5..f1b872a983 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -1050,7 +1050,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1178,18 +1178,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1266,6 +1264,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 10570fcca0..5a9553e79c 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index fdc5eaae2c..55e4e022d1 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 78f24d621f..5dc070286f 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -1055,7 +1055,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1183,18 +1183,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1271,6 +1269,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index aa32d6c092..835b9ae775 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -1055,7 +1055,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1183,18 +1183,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1271,6 +1269,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index fa333f438f..da7e08f344 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index f621f36d84..fc5885edb7 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 66faa34d1c..e3abff7f14 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - #define POWER_LOSS_PIN 69 // Pin to detect power loss + #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active #define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap #define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h index 66faa34d1c..e3abff7f14 100644 --- a/config/examples/Geeetech/A10T/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - #define POWER_LOSS_PIN 69 // Pin to detect power loss + #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active #define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap #define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index 400e1aac95..91220f34a4 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - #define POWER_LOSS_PIN 69 // Pin to detect power loss + #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss #define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active #define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap #define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 400e1aac95..91220f34a4 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - #define POWER_LOSS_PIN 69 // Pin to detect power loss + #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss #define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active #define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap #define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index 400e1aac95..91220f34a4 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - #define POWER_LOSS_PIN 69 // Pin to detect power loss + #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss #define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active #define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap #define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 72293009ef..7a8a990974 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 47ef2e9acb..362d160377 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index ca13559170..a4e1049cbe 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index 72293009ef..7a8a990974 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 47ef2e9acb..362d160377 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 36d548312c..4dc4492c72 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index ca13559170..a4e1049cbe 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index ca13559170..a4e1049cbe 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index 2f74dfc2c7..3713aedb56 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index fa333f438f..da7e08f344 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index fa333f438f..da7e08f344 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index 426f38c8d3..dd1c42a026 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -1043,7 +1043,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1171,18 +1171,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1259,6 +1257,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 9b99402bbc..09ec35f384 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index f9a0fb0fde..728af141ac 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -1056,7 +1056,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1184,18 +1184,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1272,6 +1270,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index 94af92b807..1454a79f59 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index f9a0fb0fde..728af141ac 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -1056,7 +1056,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1184,18 +1184,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1272,6 +1270,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 0b949a2876..17eb2eda95 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h index 583d6dbf14..a34a198eb6 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' #define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index ec7b3ef203..1e524ab1ff 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 91f155604e..aa0e228a89 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 378001a8f2..4fa0beeac5 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 67d8268cdf..ced4ee422a 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index 66c9615f9e..d50e76241e 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 0fa1363b4d..03762c52f7 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -1052,7 +1052,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1180,18 +1180,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1268,6 +1266,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 4560bc35e3..0f1731a072 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 1d3f0e17b4..b866763522 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 612dd404e3..48031f76d1 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index 612dd404e3..48031f76d1 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index 612dd404e3..48031f76d1 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 170f5929d2..97c5124142 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index 9d5d19606e..d07ce469f5 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -1048,7 +1048,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1176,18 +1176,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1264,6 +1262,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index 0dae98cdf8..25394e845c 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -1048,7 +1048,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1176,18 +1176,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1264,6 +1262,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index c92242fa0b..e516ac7fa5 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 756711ac8f..8ce779a5c5 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index 5ec6a024a5..b6e9982739 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index 4ebed126b7..03e5c054d0 100755 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 38b5d35880..d3c736d3c8 100755 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index aaa0eab442..80fd79e7f9 100755 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index aaa0eab442..80fd79e7f9 100755 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index 60894ca046..aa4f42ef29 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 000afabf5c..c46df8814b 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 170a92b8af..6c8c6adbd8 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index e5eeef6646..3c56769540 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index d859355a82..30b946a2b0 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index c1bf53e925..0492713ea7 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index b6a4561550..0c4f6b216f 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index 8e2f41347a..70d759e6a1 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -1064,7 +1064,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1192,18 +1192,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1280,6 +1278,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index 34ce6a0073..effa8b5ce7 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index 34ce6a0073..effa8b5ce7 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 57f382b043..66457c815f 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - #define POWER_LOSS_PIN 65 // Pin to detect power loss + #define POWER_LOSS_PIN 65 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 53ae4c7beb..e5545f76bd 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index 94a0376707..c44a4b4044 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index da2a7a9a67..777ba4c082 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index b4efcd52a6..ba78229afb 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index 0677385832..927dbd5936 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 84cd6df5a5..81e74f9034 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index 45b2fe8088..7756e1247d 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 4509b322fa..2ebc7d5e1b 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 4509b322fa..2ebc7d5e1b 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 698784490f..3c34ac05b4 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index 81c05933df..0c412def8c 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index 4426996eac..cfa66630cc 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index 4426996eac..cfa66630cc 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index 4426996eac..cfa66630cc 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index a42c2aa2f0..d912cc653e 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 6e7222a54f..dd1d6fa829 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 16f82e881a..c3b3ba0d3f 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 698784490f..3c34ac05b4 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index df3d1aca54..6763f1cc8a 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 698784490f..3c34ac05b4 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 9ecd76e8e1..d99acd7453 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -1053,7 +1053,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1181,18 +1181,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1269,6 +1267,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index d461083dff..164ccb24cf 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 4df3216ecc..fe9a5dc488 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index a21c723164..1b3733238b 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -1051,7 +1051,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1179,18 +1179,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1267,6 +1265,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index c54fa6996c..ed1646fcb2 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -1052,7 +1052,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume @@ -1180,18 +1180,16 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #if HAS_SDCARD_CONNECTION - /** - * Set this option to one of the following (or the board's defaults apply): - * - * LCD - Use the SD drive in the external LCD controller. - * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) - * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). - * - * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] - */ - //#define SDCARD_CONNECTION LCD - #endif + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD #endif // SDSUPPORT @@ -1268,6 +1266,7 @@ #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames