diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index ad1f16fc84..03c9ba55eb 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -1219,6 +1219,7 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_RECOVER_ZHOME  // Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
@@ -1230,12 +1231,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
-    //#define POWER_LOSS_RECOVER_ZHOME
-    #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
-      //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
-    #endif
   #endif
 
   /**
diff --git a/config/examples/Raiscube/A8r/Configuration_adv.h b/config/examples/Raiscube/A8r/Configuration_adv.h
index db02ea9c3e..86a1a75dff 100644
--- a/config/examples/Raiscube/A8r/Configuration_adv.h
+++ b/config/examples/Raiscube/A8r/Configuration_adv.h
@@ -1219,6 +1219,7 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_RECOVER_ZHOME  // Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
@@ -1230,12 +1231,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
-    //#define POWER_LOSS_RECOVER_ZHOME
-    #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
-      //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
-    #endif
   #endif
 
   /**
diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h
index 2d76db982b..75b9b3c539 100644
--- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h	
+++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h	
@@ -1231,12 +1231,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
-    //#define POWER_LOSS_RECOVER_ZHOME
-    #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
-      //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
-    #endif
   #endif
 
   /**
diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h
index 2d76db982b..75b9b3c539 100644
--- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h	
+++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h	
@@ -1231,12 +1231,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
-    //#define POWER_LOSS_RECOVER_ZHOME
-    #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
-      //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
-    #endif
   #endif
 
   /**
diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h
index 2d76db982b..75b9b3c539 100644
--- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h	
+++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h	
@@ -1231,12 +1231,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
-    //#define POWER_LOSS_RECOVER_ZHOME
-    #if ENABLED(POWER_LOSS_RECOVER_ZHOME)
-      //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
-    #endif
   #endif
 
   /**