diff --git a/config/examples/delta/Velleman/K8800/Configuration.h b/config/examples/delta/Velleman/K8800/Configuration.h
index 62d23cadd9..c09323e569 100644
--- a/config/examples/delta/Velleman/K8800/Configuration.h
+++ b/config/examples/delta/Velleman/K8800/Configuration.h
@@ -1710,7 +1710,7 @@
 // @section homing
 
 //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
-#define HOME_AFTER_DEACTIVATE   // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
+#define HOME_AFTER_DEACTIVATE     // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
 
 /**
  * Set Z_IDLE_HEIGHT if the Z-Axis moves on its own when steppers are disabled.
diff --git a/config/examples/delta/Velleman/K8800/Configuration_adv.h b/config/examples/delta/Velleman/K8800/Configuration_adv.h
index faf7253235..507d5ac0c6 100644
--- a/config/examples/delta/Velleman/K8800/Configuration_adv.h
+++ b/config/examples/delta/Velleman/K8800/Configuration_adv.h
@@ -303,9 +303,9 @@
   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
   #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
 
-  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING                // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING      // Don't slow fan speed during M303
   #endif
 
   /**
@@ -1766,6 +1766,15 @@
  */
 //#define NO_SD_HOST_DRIVE   // Disable SD Card access over USB (for security).
 
+/**
+ * By default the framework is responsible for the shared media I/O.
+ * Enable this if you need Marlin to take care of the shared media I/O.
+ * Useful if shared media isn't working properly on some boards.
+ */
+#if ENABLED(SDSUPPORT) && DISABLED(NO_SD_HOST_DRIVE)
+  //#define DISKIO_HOST_DRIVE
+#endif
+
 /**
  * Additional options for Graphical Displays
  *
@@ -3599,6 +3608,14 @@
  */
 //#define CNC_COORDINATE_SYSTEMS
 
+/**
+ * CNC Drilling Cycle - UNDER DEVELOPMENT
+ *
+ * Enables G81 to perform a drilling cycle.
+ * Currently only supports a single cycle, no G-code chaining.
+ */
+//#define CNC_DRILLING_CYCLE
+
 // @section reporting
 
 /**
@@ -4178,6 +4195,8 @@
     #define MMU2_CAN_LOAD_INCREMENT_SEQUENCE \
       { -MMU2_CAN_LOAD_INCREMENT, MMU2_CAN_LOAD_FEEDRATE }
 
+    // Continue unloading if sensor detects filament after the initial unload move
+    //#define MMU_IR_UNLOAD_MOVE
   #else
 
     /**