diff --git a/config/default/Configuration.h b/config/default/Configuration.h index be70c4bc3c..7c333a9522 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index 3c4405ba96..34cbea0f41 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -1313,10 +1313,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index 490526e433..9a5360031c 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index 91dd505cb7..193926e823 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 8a136f550e..6e89257d0e 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -1324,10 +1324,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index e4556e4abc..85bb9b54c6 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -1384,10 +1384,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index efda85f10b..2f6ea34b35 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -1383,10 +1383,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 3cc5faeb56..af42cd87f3 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 4d59932dec..127bc0aaa1 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -1317,10 +1317,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index eaa9b9d5b4..53e7948156 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index a67b30ada9..9adfa2915e 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 028186ad1b..ea25b2f0cd 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -1405,10 +1405,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 7a588fb3f2..bc603707ce 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -1332,10 +1332,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index c532d5be44..bf432f4b6b 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index cefba78fcc..2d51b33baa 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -1303,10 +1303,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h index 21109c4446..1230979d17 100644 --- a/config/examples/Anet/E16/Configuration.h +++ b/config/examples/Anet/E16/Configuration.h @@ -1317,10 +1317,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index db7cefb20a..f58aee6431 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 5aef037035..a2acb48c38 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -1307,10 +1307,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Artillery/Genius/Configuration.h b/config/examples/Artillery/Genius/Configuration.h index 41d3ccfd8f..1dca3bd036 100644 --- a/config/examples/Artillery/Genius/Configuration.h +++ b/config/examples/Artillery/Genius/Configuration.h @@ -1288,10 +1288,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Artillery/Sidewinder X1/Configuration.h b/config/examples/Artillery/Sidewinder X1/Configuration.h index 111a64c15e..df76a2fed9 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 26d9ee16ba..5fb73a1d19 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 01922dbb35..85ac3993f7 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index f349cc38c1..b104205232 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index c4058391f9..9134e8415a 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -1294,10 +1294,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 0f825c9341..1ebbcb0b98 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -1307,10 +1307,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 4923429cf9..60cceea776 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -1294,10 +1294,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h index 1f93dd87e0..fdbfad9160 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration.h @@ -1297,10 +1297,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h index ef9d2c8e06..668f1d48df 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration.h @@ -1298,10 +1298,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index 26ba49cd54..c543981286 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -1305,10 +1305,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h index 5d41f72b3b..f5b0aec651 100644 --- a/config/examples/Creality/CR-10/Configuration.h +++ b/config/examples/Creality/CR-10/Configuration.h @@ -1316,10 +1316,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h index beb46e358e..853de9b07d 100644 --- a/config/examples/Creality/CR-10S/Configuration.h +++ b/config/examples/Creality/CR-10S/Configuration.h @@ -1307,10 +1307,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h index 1bb9c50042..aa779dbf7f 100644 --- a/config/examples/Creality/CR-10_5S/Configuration.h +++ b/config/examples/Creality/CR-10_5S/Configuration.h @@ -1309,10 +1309,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h index 91e8d3dcaf..ffa8488c1c 100644 --- a/config/examples/Creality/CR-10mini/Configuration.h +++ b/config/examples/Creality/CR-10mini/Configuration.h @@ -1325,10 +1325,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index c04b191ddb..939dd00049 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index dfa208b353..c59de68e6c 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 9768f2038c..8af17c1efe 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index a912965e6e..55fb0b7331 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h index f02ddb32b5..fe95a50ccb 100644 --- a/config/examples/Creality/Ender-3/Configuration.h +++ b/config/examples/Creality/Ender-3/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index 8867a40782..13db2e31c1 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/Configuration.h b/config/examples/Creality/Ender-5 Pro/Configuration.h index fb8a9d2ab5..aeed322167 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration.h @@ -1304,10 +1304,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Creality/Ender-5/Configuration.h b/config/examples/Creality/Ender-5/Configuration.h index 6b1564c508..cbc91c94ba 100644 --- a/config/examples/Creality/Ender-5/Configuration.h +++ b/config/examples/Creality/Ender-5/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index eaf5ed7e08..f0688b12b7 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -1305,10 +1305,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 5eb51ab1f8..9df400af7e 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -1303,10 +1303,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index f3f49d0fd5..1c58850235 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 87298a6bcb..9feb4688bb 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h index 5da93c7ff6..503e453e09 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h index f9ad6a6ab7..1edb7f71d6 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h index d6b48f7332..2c4795f927 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/Cheetah/base/Configuration.h b/config/examples/FYSETC/Cheetah/base/Configuration.h index 68ebfc9d97..19b5ceb66a 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 75d0421493..52f09d391a 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -1307,10 +1307,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index 842ea0dece..1aff92a292 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -1305,10 +1305,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 0b098a5504..51f0b6c31c 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -1288,10 +1288,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index a9d2525efc..5ba9ed20d7 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -1288,10 +1288,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index d4eab89dc9..aad4371a58 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -1299,10 +1299,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 286efccf8e..021786baba 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -1325,10 +1325,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index b735f8b75f..ea77b046ee 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -1423,10 +1423,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 51aa09f27c..df6ed39ae7 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -1351,10 +1351,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index f088d6405d..8d8ec4f858 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -1335,10 +1335,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index a34eba773e..e03fcb223e 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -1289,10 +1289,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index 29ad26e177..778aef6aae 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -1291,10 +1291,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index ef0283376e..8df9e542cd 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -1291,10 +1291,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A10T/Configuration.h b/config/examples/Geeetech/A10T/Configuration.h index a2909648e6..5ab7055063 100644 --- a/config/examples/Geeetech/A10T/Configuration.h +++ b/config/examples/Geeetech/A10T/Configuration.h @@ -1292,10 +1292,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index 33c1bc9701..c99b338fef 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -1289,10 +1289,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index e9d40ca85f..1dca963c14 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -1290,10 +1290,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index 9dc3f34698..78b81981df 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -1291,10 +1291,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index ec2a1e3ac8..35ca0ba3b7 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -1288,10 +1288,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index 7ba542f686..a98cf5271c 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -1288,10 +1288,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index 2f4149a639..9bcf429cf1 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -1302,10 +1302,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index 824f71411b..c467322cb3 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -1289,10 +1289,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 3882686b55..ce97c778b8 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -1319,10 +1319,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 76c91ca21c..90c2798cab 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index 34b2611417..62faf172f8 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -1288,10 +1288,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 723c649b0a..23fc809a0b 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -1313,10 +1313,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index becf674a36..deebea701e 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -1304,10 +1304,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index d909ff1a65..17c0ff63c3 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -1302,10 +1302,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index ea43e5c571..7cc9b953fa 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -1325,10 +1325,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 35e6bfd297..1ec2ddb7b8 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -1325,10 +1325,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 93d3f6bcd4..411bfc26b8 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -1324,10 +1324,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index fab90f45df..6c8d208773 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 41cb6c49c5..6a7ee396d7 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index a8f4375d89..773002a053 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -1292,10 +1292,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index b178c6159b..c00a7755d9 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index f54021d548..5e03ff3d64 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -1309,10 +1309,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index d22632bd0f..89db2c6cdd 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -1317,10 +1317,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index 4e676cc104..8d13f2b592 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -1309,10 +1309,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index 89bf8b476b..dbd7ef12b8 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -1305,10 +1305,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration.h b/config/examples/MakerFarm/Pegasus_12/Configuration.h index c9d9ca910c..68e28cb3ff 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration.h @@ -1308,10 +1308,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 2e444a50c8..8ca87332ce 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index a66529c729..94e1e6ca7a 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -1347,10 +1347,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index e6d831f7c3..66c8e7f993 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index f39a951694..82826e2272 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index de9a61dc27..0e0376afd6 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 4502019384..df01b39b2d 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -1307,10 +1307,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index 64d90b195f..73a7e1b7ce 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -1313,10 +1313,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index 4cfcd456db..3b538abac2 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -1312,10 +1312,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index bf06002c2d..7110238eb4 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -1303,10 +1303,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index f830d83c1a..da08eedf2c 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index 2b2764315b..5dfd1e975c 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 220fc00e8b..cc35f302bd 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -1305,10 +1305,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index a2c5051bc5..de452e5bc7 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -1314,10 +1314,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index 406030471c..9a0980719d 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -1314,10 +1314,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index dbb60410c7..c74ab0c388 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -1314,10 +1314,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 602f923a3b..12a31f9c0c 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -1354,10 +1354,10 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 90d282a9f9..d201eddd3d 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index dcac627be7..bb7f828395 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -1304,10 +1304,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 772de63be9..22876fd169 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -1328,10 +1328,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 3fd2394e90..66032e5f37 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -1328,10 +1328,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index d5fd8f7fad..b56b448f44 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index f477b2d3c8..1a38bc5be5 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -1308,10 +1308,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 0bac9d3e42..bb2167e8cc 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h index 4aec6c5155..02bd5650be 100644 --- a/config/examples/STM32/stm32f103ret6/Configuration.h +++ b/config/examples/STM32/stm32f103ret6/Configuration.h @@ -1308,10 +1308,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 6b30916036..5cc0a04d31 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -1337,10 +1337,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index ce34283558..cdb6d3c2aa 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -1310,10 +1310,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index cbe7b1ca9e..dea3d795f3 100755 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -1289,10 +1289,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index 8cfb947bba..0da08423c3 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 941f5fff01..1835d4f7f6 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -1310,10 +1310,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index 290421cb3f..94d7f0033a 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -1310,10 +1310,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 8c3fd326dd..d8dec07f5a 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index d12450401b..af30a01995 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -1362,10 +1362,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index e26289849d..72ce58bb4c 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 152a2db718..4f275668a5 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -1310,10 +1310,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index bc893df55b..d988eb43ab 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -1325,10 +1325,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 9690da62aa..78595fef5c 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -1306,10 +1306,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index f3c5cbfea3..ea77987c74 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -1317,10 +1317,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 4fb94e0269..4e38afb49d 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -1303,10 +1303,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index 896faa381c..4972de5365 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -1305,10 +1305,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 12ea61d5ad..e3020a2ede 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -1314,10 +1314,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index 4b3d1547ab..2acde99623 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -1334,10 +1334,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index b2bb24f2c7..ee56f1ae70 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 6780db1d7a..0e5cc2cc7e 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 5862d5b096..78182c0f62 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -1325,10 +1325,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 9496303af9..66281e7c5f 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index f0a6bf2819..bb8c82a10b 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -1316,10 +1316,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 29168f7f63..1a6dce781d 100755 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -1305,10 +1305,10 @@ #define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index 6192c54dfb..eba76d0d88 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -1306,10 +1306,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index c7598de638..2129b3bd36 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -1473,10 +1473,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index bc94e6272d..ff02e12ac4 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -1413,10 +1413,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index 360ba0653c..c2a69d2ee6 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -1425,10 +1425,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index cbf670aeb8..81b91d0774 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -1415,10 +1415,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index b0b88f3514..232bf21ec9 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -1419,10 +1419,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index 6f176464ea..da13cee739 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -1418,10 +1418,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 8a01480626..859d52e618 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -1418,10 +1418,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index db54e55fb7..49ebb85fa8 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -1401,10 +1401,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index ac37514c62..c3dee4889f 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -1401,10 +1401,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index 33431e585e..af5fcc3509 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -1401,10 +1401,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index 33431e585e..af5fcc3509 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -1401,10 +1401,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 7ec8ccf233..70191c5b86 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -1406,10 +1406,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index bf24672abe..5b3758595d 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -1434,10 +1434,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 02223ea86d..85081713a1 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -1406,10 +1406,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 2b78fb9138..c092b207c5 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -1410,10 +1410,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 205d5241dd..f638766e42 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -1406,10 +1406,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index d5a0ffbf35..16206cd239 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -1399,10 +1399,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index 5812579f2f..baeabd21d3 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -1408,10 +1408,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index 12bc36a3e9..53568cc2a2 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -1408,10 +1408,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 3c166f80f8..2cd4026eff 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -1409,10 +1409,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 3f72ec303e..66bc2010ef 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -1332,10 +1332,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 68c22b5bee..eb6a7b6ed1 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -1309,10 +1309,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index e71eb2c642..d985fb6450 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -1301,10 +1301,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /** diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h index 74778cf7d5..07d3d48931 100644 --- a/config/examples/wt150/Configuration.h +++ b/config/examples/wt150/Configuration.h @@ -1311,10 +1311,10 @@ //#define LEVEL_BED_CORNERS #if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner + #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif /**