diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 6a321448bf..f567f50389 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -1709,18 +1709,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1740,7 +1740,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index b2b8fdb141..eda0821089 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index 903c38214b..3c785c6076 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index 2ef6dfab59..b27d53a0f8 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index cced848e05..38337f4b01 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -1792,18 +1792,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1823,7 +1823,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 03abac0441..12d877152f 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -1793,18 +1793,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.2 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1824,7 +1824,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 49d85a1aa9..09bfba9104 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 2e10bb04cd..ff61ea32f0 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index d1400f12b5..016bb71d9d 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 3c1f7c7c61..31cb6154a9 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index f8ebb2fd71..474daa3c5a 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -1788,18 +1788,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1819,7 +1819,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 5339869523..3461d253a5 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index f92d728961..44f424d58c 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h index e66c03d3a8..bb9e74edd2 100644 --- a/config/examples/Anet/A9/Configuration.h +++ b/config/examples/Anet/A9/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index ed8561fccf..f526c42942 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h index 2403833c72..9c2d573315 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h index 5c65ab3bee..4f613eebf0 100644 --- a/config/examples/Anet/E16/Stock/Configuration.h +++ b/config/examples/Anet/E16/Stock/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET4+/Configuration.h b/config/examples/Anet/ET4+/Configuration.h index bd34f1b785..92d6c9a362 100644 --- a/config/examples/Anet/ET4+/Configuration.h +++ b/config/examples/Anet/ET4+/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET4-Pro/Configuration.h b/config/examples/Anet/ET4-Pro/Configuration.h index e082f0774e..a53fc5e0a8 100644 --- a/config/examples/Anet/ET4-Pro/Configuration.h +++ b/config/examples/Anet/ET4-Pro/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h index 60ea4d48d1..5eeb22c495 100644 --- a/config/examples/Anet/ET4/Configuration.h +++ b/config/examples/Anet/ET4/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET4X/Configuration.h b/config/examples/Anet/ET4X/Configuration.h index cc0cb4c96a..bb54624625 100644 --- a/config/examples/Anet/ET4X/Configuration.h +++ b/config/examples/Anet/ET4X/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET5-Pro/Configuration.h b/config/examples/Anet/ET5-Pro/Configuration.h index 5e015e6ba5..bbe787a628 100644 --- a/config/examples/Anet/ET5-Pro/Configuration.h +++ b/config/examples/Anet/ET5-Pro/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET5/Configuration.h b/config/examples/Anet/ET5/Configuration.h index 5ded64872d..901394aa2b 100644 --- a/config/examples/Anet/ET5/Configuration.h +++ b/config/examples/Anet/ET5/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Anet/ET5X/Configuration.h b/config/examples/Anet/ET5X/Configuration.h index 656dc5c0ff..f7f534e478 100644 --- a/config/examples/Anet/ET5X/Configuration.h +++ b/config/examples/Anet/ET5X/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h index 142e7a47f3..32ddb4b922 100644 --- a/config/examples/AnyCubic/Chiron/Configuration.h +++ b/config/examples/AnyCubic/Chiron/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h index 45b41fb25d..52d983fffd 100644 --- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h index 6bd2ee5805..d4594dc11f 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h index d299bdc6d4..37963ac60b 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h index 9d1bc9aafb..3511ed55c5 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration.h @@ -1747,18 +1747,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1778,7 +1778,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 630aa03b7a..e9a3dd937c 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 16748bc77b..2f0a882460 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Genius Pro/Configuration.h b/config/examples/Artillery/Genius Pro/Configuration.h index 21589fe716..8cf97ae6e4 100644 --- a/config/examples/Artillery/Genius Pro/Configuration.h +++ b/config/examples/Artillery/Genius Pro/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Genius/BLTouch/Configuration.h b/config/examples/Artillery/Genius/BLTouch/Configuration.h index de8dc2c9c3..439578fb44 100644 --- a/config/examples/Artillery/Genius/BLTouch/Configuration.h +++ b/config/examples/Artillery/Genius/BLTouch/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Genius/V1/Configuration.h b/config/examples/Artillery/Genius/V1/Configuration.h index 6e55594a8b..8364859c3d 100644 --- a/config/examples/Artillery/Genius/V1/Configuration.h +++ b/config/examples/Artillery/Genius/V1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Hornet/Configuration.h b/config/examples/Artillery/Hornet/Configuration.h index b3cf93c859..b15a04ed08 100644 --- a/config/examples/Artillery/Hornet/Configuration.h +++ b/config/examples/Artillery/Hornet/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 40, 40, 40, 40 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 40, 40, 40, 40 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h index fedaef212b..c6fcd46b60 100644 --- a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h @@ -1729,18 +1729,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1760,7 +1760,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h index 1e99d9990a..ea72d193f8 100644 --- a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Artillery/Sidewinder X2/Configuration.h b/config/examples/Artillery/Sidewinder X2/Configuration.h index b6ca4f4c76..623e961d43 100644 --- a/config/examples/Artillery/Sidewinder X2/Configuration.h +++ b/config/examples/Artillery/Sidewinder X2/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 7b3d745ade..6fceaf2721 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 9f89ac10b2..0e3864e57e 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 0f84a976b4..ce5e69b450 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -1669,18 +1669,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1700,7 +1700,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h index a80de3d343..5db986ac4c 100644 --- a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h +++ b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h @@ -1726,18 +1726,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1757,7 +1757,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIQU/B1 - SKR 2/Configuration.h b/config/examples/BIQU/B1 - SKR 2/Configuration.h index d04569563a..e0160af313 100644 --- a/config/examples/BIQU/B1 - SKR 2/Configuration.h +++ b/config/examples/BIQU/B1 - SKR 2/Configuration.h @@ -1726,18 +1726,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1757,7 +1757,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIQU/B1 SE Plus/Configuration.h b/config/examples/BIQU/B1 SE Plus/Configuration.h index 9e95da5ba3..95b5f2a161 100644 --- a/config/examples/BIQU/B1 SE Plus/Configuration.h +++ b/config/examples/BIQU/B1 SE Plus/Configuration.h @@ -1711,18 +1711,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1742,7 +1742,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIQU/BX/Configuration.h b/config/examples/BIQU/BX/Configuration.h index 6c8f816c15..4b7cd56a57 100644 --- a/config/examples/BIQU/BX/Configuration.h +++ b/config/examples/BIQU/BX/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BIQU/Thunder Standard/Configuration.h b/config/examples/BIQU/Thunder Standard/Configuration.h index 5588bc1c4b..9d2b6a80ac 100644 --- a/config/examples/BIQU/Thunder Standard/Configuration.h +++ b/config/examples/BIQU/Thunder Standard/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 8a2d05f27e..28111d3c3e 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index aa6f6273b2..20eec79828 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -1727,18 +1727,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1758,7 +1758,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index f21e14a96a..fc96ccf13b 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/CTC/A13/Configuration.h b/config/examples/CTC/A13/Configuration.h index 3396adc8a0..bd25246560 100644 --- a/config/examples/CTC/A13/Configuration.h +++ b/config/examples/CTC/A13/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/CTC/Bizer/Configuration.h b/config/examples/CTC/Bizer/Configuration.h index a2e2faabee..cd9b5912f1 100644 --- a/config/examples/CTC/Bizer/Configuration.h +++ b/config/examples/CTC/Bizer/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index a745bf3df8..6a43d79e28 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index 25c4e6ce90..f59f97f271 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -1729,18 +1729,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1760,7 +1760,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index ed704bb614..4c5fe64f84 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 9388f17d3f..62cfe775af 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index d37ea36c60..8ae848e58d 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h index 5d44ce6258..d37136d48c 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1722,18 +1722,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1753,7 +1753,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/README.md b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/README.md index bb1653a99a..1345949ed9 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/README.md +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/README.md @@ -57,7 +57,7 @@ By default, this is disabled. Enabling this seemed to provide better mesh data. Provides control panel probe controls. ```cpp -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING ``` Provides control panel bed tramming controls. diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h index 0858b43c42..dcefb9ffd8 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h @@ -1722,18 +1722,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1753,7 +1753,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h index 48e7a684b5..0c6b9be487 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h index 102ee41f3b..76e9a59412 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h index 1bba40ac8d..eec6663547 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h index 9d4f5159e5..cb267da811 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h index 448b4f96fb..348a8ce3a1 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index 070bdbdd9e..4d69a8df0b 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -1740,18 +1740,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1771,7 +1771,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10 V3/Configuration.h b/config/examples/Creality/CR-10 V3/Configuration.h index 8985c98fa3..21e495171d 100644 --- a/config/examples/Creality/CR-10 V3/Configuration.h +++ b/config/examples/Creality/CR-10 V3/Configuration.h @@ -1743,20 +1743,20 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 45, 45, 45, 45 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 45, 45, 45, 45 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner #if ENABLED(CR10V3_BLTOUCH) - #define LEVEL_CORNERS_USE_PROBE + #define BED_TRAMMING_USE_PROBE #endif - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1776,7 +1776,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h index 49b7366ac1..e9d613affb 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h index 31c14d364a..f09f72930b 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h index 01ce8ec34c..22b5b58c20 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h index 132f37befc..6896de2fc7 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h index 3fc5fb171a..6a6466d9aa 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h index 43dc0df41a..26182afc6f 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h index 08bfbc49d7..3e26fa78a0 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index 4d5b813cbc..3bdb7d0cda 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 68fc2e6ceb..8ba08c0c3b 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration.h b/config/examples/Creality/CR-30 PrintMill/Configuration.h index 4c2f7c9192..e66a1b4dca 100644 --- a/config/examples/Creality/CR-30 PrintMill/Configuration.h +++ b/config/examples/Creality/CR-30 PrintMill/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index f4307d6e07..d20e3e4c55 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h index f98b1ceadd..afb8078dc9 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 44614865fc..65967421cd 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Max/Configuration.h b/config/examples/Creality/Ender-3 Max/Configuration.h index 957604486d..8fc5530587 100644 --- a/config/examples/Creality/Ender-3 Max/Configuration.h +++ b/config/examples/Creality/Ender-3 Max/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h index dc72e114fd..da3de9dd21 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h index a4d66b7538..fa5a7a2e1d 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index c94e56fec7..0646dd3edb 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h index 27e388b1c1..f1faa10208 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h index a042a684ca..ea27360a9d 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h index 9edfa46259..ee73b4ee14 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h index 6fa64d1b66..e0ca01a0f7 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h index 31d9e80c6b..5d64f34ecb 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 S1/Configuration.h b/config/examples/Creality/Ender-3 S1/Configuration.h index 01ad402756..4989c6ab3b 100644 --- a/config/examples/Creality/Ender-3 S1/Configuration.h +++ b/config/examples/Creality/Ender-3 S1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h index 14238d2c95..15723a7607 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h index 6b5ea22c49..12d72e959a 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h index cd69ecf73f..2266bf6e27 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h @@ -1749,18 +1749,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1780,7 +1780,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h index 42b370fce9..7e33e85b4f 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h @@ -1749,18 +1749,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1780,7 +1780,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h index 19d18930e7..562f9879e7 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h index 3000cfa5ef..db731e5ccd 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h index 9390b9ac07..66342bc7fb 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h index 2e70276e13..d6787b7bec 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h index 63ee9df77a..fef033b80a 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h index f6f03e6087..438cf1c9fb 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h index fab8ec6294..4b66805a88 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h index b3882247de..ed610cd90a 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index 4ad0d32f63..e36c68bbe3 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index 8a3d4231d6..2f2ceb1be0 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index 2ae83569dc..c2ae15d3f0 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h index 8ee4e51601..44cbef885c 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index 056064672a..738dae9372 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h index 13eef38186..1f6378ed77 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h @@ -1720,18 +1720,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1751,7 +1751,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h index 78a9d527fc..af6aaafdad 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index 25873aae84..94c263ba92 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 32261e7ed5..b3ad9f1f9d 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h index 347ad2b1de..860a91b41c 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index 45514a4926..5e96c698e9 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index ab29fdea82..7900a876cb 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index c868c8f8d6..e1ae7cce53 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h index 8aea71aee9..f6e4ab8b28 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h index 7b8cebacde..a4a4efb4c1 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h index 96a4909584..a2175edb5c 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h index 3a46a92070..baa4a26b06 100644 --- a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h +++ b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index f9a588dc0e..a0a9c3a955 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h index 2e34d73e04..afe48f7d8f 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration.h @@ -1722,18 +1722,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1753,7 +1753,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h index 78d349e625..9fd10d664e 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h @@ -1720,18 +1720,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1751,7 +1751,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index 3a9fb4f5b7..6a1b2e156e 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1610,6 +1610,9 @@ // at which point movement will be level to the machine's XY plane. // The height can be set with M420 Z #define ENABLE_LEVELING_FADE_HEIGHT + #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) + #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height. + #endif // For Cartesian machines, instead of dividing moves on mesh boundaries, // split up moves into short segments like a Delta. This follows the @@ -1709,13 +1712,38 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK + #endif + + /** + * Corner Leveling Order + * + * Set 2 or 4 points. When 2 points are given, the 3rd is the center of the opposite edge. + * + * LF Left-Front RF Right-Front + * LB Left-Back RB Right-Back + * + * Examples: + * + * Default {LF,RB,LB,RF} {LF,RF} {LB,LF} + * LB --------- RB LB --------- RB LB --------- RB LB --------- RB + * | 4 3 | | 3 2 | | <3> | | 1 | + * | | | | | | | <3>| + * | 1 2 | | 1 4 | | 1 2 | | 2 | + * LF --------- RF LF --------- RF LF --------- RF LF --------- RF + */ + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h index 292a1dc757..a32f5b3521 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/README.md b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/README.md index 7a21aa7b48..06fea7a974 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/README.md +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/README.md @@ -33,7 +33,7 @@ The configuration was made on a Phaetus Dragon hotend and a BMG clone extruder, - Enabled `MESH_EDIT_GFX_OVERLAY`, set `MESH_INSET` to `10` and `GRID_MAX_POINTS_X` to `9` (for UBL) - Enabled `LCD_BED_LEVELING` - Enabled `MESH_EDIT_MENU` -- Enabled `LEVEL_BED_CORNERS` +- Enabled `LCD_BED_TRAMMING` - Enabled `Z_SAFE_HOMING` - Set `HOMING_FEEDRATE_MM_M` to faster values - Enabled `NOZZLE_PARK_FEATURE` diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h index d0ba5df184..a862f0e5e2 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h index 8e49d56345..6e73cc4a6a 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h index 11f77d9029..023e017a62 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h index 197a11593c..ba2e1b1932 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h index 341882171e..21d98680fe 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h index 2afd7148ed..f283e163cd 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index c924a553f4..f550626144 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h index 10ef2abdf9..2e225cafe9 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h index 531e96929b..33b1b68f5b 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Creality/Ender-6/Configuration.h b/config/examples/Creality/Ender-6/Configuration.h index ec69511b07..3a87e93882 100644 --- a/config/examples/Creality/Ender-6/Configuration.h +++ b/config/examples/Creality/Ender-6/Configuration.h @@ -1720,18 +1720,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1751,7 +1751,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index cb705308ca..be801a34bc 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index 3be606e1a2..4239c4530e 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 640e761a2b..d0997f145c 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h index d0e1e51475..3e226deac9 100644 --- a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h +++ b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 883ef2a8de..ed2a387670 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Elegoo/Neptune 2/Configuration.h b/config/examples/Elegoo/Neptune 2/Configuration.h index f7bb77ccf9..ec0fe6a4f4 100644 --- a/config/examples/Elegoo/Neptune 2/Configuration.h +++ b/config/examples/Elegoo/Neptune 2/Configuration.h @@ -1776,18 +1776,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1807,7 +1807,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Eryone/Thinker SE/Configuration.h b/config/examples/Eryone/Thinker SE/Configuration.h index 615e82532b..00484d71d9 100644 --- a/config/examples/Eryone/Thinker SE/Configuration.h +++ b/config/examples/Eryone/Thinker SE/Configuration.h @@ -1757,18 +1757,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1788,7 +1788,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Eryone/Thinker V2/Configuration.h b/config/examples/Eryone/Thinker V2/Configuration.h index 28682338ca..87155ab41b 100644 --- a/config/examples/Eryone/Thinker V2/Configuration.h +++ b/config/examples/Eryone/Thinker V2/Configuration.h @@ -1754,18 +1754,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1785,7 +1785,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 2d434a8aed..6ea35c1623 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index f41f2a97ac..7b96a847b9 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index a7f1e3acf6..113919081d 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index ccc51f284e..170af80f7e 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index 1fb27528a3..ea8eacb50b 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index 6495b421f1..ff12534abc 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index ff271ddbbd..b6f683a67a 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FlyingBear/P902/Configuration.h b/config/examples/FlyingBear/P902/Configuration.h index 2a89219d79..1fe2b5cd95 100644 --- a/config/examples/FlyingBear/P902/Configuration.h +++ b/config/examples/FlyingBear/P902/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index a3a5f20cc2..7ccc4d2970 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FoamCutter/Configuration.h b/config/examples/FoamCutter/Configuration.h index b74a38a7b5..b5bd10cc24 100644 --- a/config/examples/FoamCutter/Configuration.h +++ b/config/examples/FoamCutter/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 2a1335d404..dd0da6151d 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 7e92643d8f..b1edecf78b 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -1824,18 +1824,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1855,7 +1855,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 64e1058c2d..768ed3dfe3 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index b24c84ebf0..58a543e7c1 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -1726,18 +1726,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1757,7 +1757,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index c7916e4fdf..d0299c694b 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index 93cf7cc7fe..7cbd2227ed 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h index 1f25f8dbaf..ab17e2416a 100644 --- a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h index 6b4c9f4bb1..b753fe6e9d 100644 --- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10PRO/Configuration.h b/config/examples/Geeetech/A10PRO/Configuration.h index 137df29d1a..ab8ee6da3e 100644 --- a/config/examples/Geeetech/A10PRO/Configuration.h +++ b/config/examples/Geeetech/A10PRO/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h index 70c5436287..5d6c631cd6 100644 --- a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h index eb6cc94b6c..43aa64bfff 100644 --- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index 8a53d0357d..12011d6add 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index cf78ccb09f..f37a4c2f22 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index a2ba843328..3caef2d62a 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 252718f44d..ddaddb33a8 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A30M/Configuration.h b/config/examples/Geeetech/A30M/Configuration.h index c3de81698d..2c6d96c690 100644 --- a/config/examples/Geeetech/A30M/Configuration.h +++ b/config/examples/Geeetech/A30M/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/A30T/Configuration.h b/config/examples/Geeetech/A30T/Configuration.h index 81a2433932..c67f69940d 100644 --- a/config/examples/Geeetech/A30T/Configuration.h +++ b/config/examples/Geeetech/A30T/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index 4e5ea049b5..b70ab47492 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index 77866f3727..717320452c 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index 98b11d47a1..294fbc5b97 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index f7c2bcbd67..7f07f54a1e 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 11875a41e9..dddde92f05 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index f5c3cf1677..32a4d74430 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 28c3d8ea0f..9659730523 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index b0bc63d9d3..eb2d603857 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 1a43c5b23d..6d62f8b7d9 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index 650b9ca307..38d749c2cc 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -1723,18 +1723,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1754,7 +1754,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 1d2252dfcf..8b706306bd 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -1724,18 +1724,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1755,7 +1755,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/README.md b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/README.md index d908932c50..c36feb71ae 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/README.md +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/README.md @@ -10,7 +10,7 @@ The main characteristics of these configurations are: - An example `SKEW_CORRECTION` for a particular printer is enabled. See comments below about how to adjust it to a particular printer. - Using the LCD controller for bed leveling is enabled. - `PROBE_MANUALLY` is enabled, which *provides a means to do "Auto" Bed Leveling without a probe*. - - The `LEVEL_BED_CORNERS` option for manual bed adjustment is enabled. + - The `LCD_BED_TRAMMING` option for manual bed adjustment is enabled. - Bilinear bed leveling is enabled, the boundaries for probing are adjusted to the glass size, and extrapolation is enabled. - `PRINTCOUNTER` is enabled, in order to track statistical data. - `INDIVIDUAL_AXIS_HOMING_MENU` is enabled, which adds individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 1124e15661..d84760337f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -1723,18 +1723,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1754,7 +1754,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md index d908932c50..c36feb71ae 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md @@ -10,7 +10,7 @@ The main characteristics of these configurations are: - An example `SKEW_CORRECTION` for a particular printer is enabled. See comments below about how to adjust it to a particular printer. - Using the LCD controller for bed leveling is enabled. - `PROBE_MANUALLY` is enabled, which *provides a means to do "Auto" Bed Leveling without a probe*. - - The `LEVEL_BED_CORNERS` option for manual bed adjustment is enabled. + - The `LCD_BED_TRAMMING` option for manual bed adjustment is enabled. - Bilinear bed leveling is enabled, the boundaries for probing are adjusted to the glass size, and extrapolation is enabled. - `PRINTCOUNTER` is enabled, in order to track statistical data. - `INDIVIDUAL_AXIS_HOMING_MENU` is enabled, which adds individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index beaf5055e3..24cd430a7f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index fce41c9b63..d856c9c103 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 0cd580a11d..d910292504 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -1711,18 +1711,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1742,7 +1742,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Index/REV_03/Configuration.h b/config/examples/Index/REV_03/Configuration.h index 3b16b62595..1754c42d48 100644 --- a/config/examples/Index/REV_03/Configuration.h +++ b/config/examples/Index/REV_03/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 3cd3cfcf63..79fc299aed 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h index 979f6043ac..ddee3e24d3 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index ca9bb897a7..f1044b9111 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index c54bf2cc1d..91331e5845 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 651cc8aacb..d26c70bcdc 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -1721,18 +1721,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1752,7 +1752,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index be4f9d38ae..27bad58321 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index 4191f4101d..cd495e7ce0 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index b8bf72005f..b4d35c7d16 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Kingroon/KP3S/Configuration.h b/config/examples/Kingroon/KP3S/Configuration.h index deabb2e6e5..116a550bb2 100644 --- a/config/examples/Kingroon/KP3S/Configuration.h +++ b/config/examples/Kingroon/KP3S/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Labists/ET4/Configuration.h b/config/examples/Labists/ET4/Configuration.h index 4f7ec919a6..9e967bc634 100644 --- a/config/examples/Labists/ET4/Configuration.h +++ b/config/examples/Labists/ET4/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.05 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/LulzBot/TAZ4/Configuration.h b/config/examples/LulzBot/TAZ4/Configuration.h index b3aa34f7f9..e07e6fd70d 100644 --- a/config/examples/LulzBot/TAZ4/Configuration.h +++ b/config/examples/LulzBot/TAZ4/Configuration.h @@ -1724,18 +1724,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1755,7 +1755,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index a980a82377..5606e7c29b 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h index 4fae049795..b591add548 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 5.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 3763a931dd..14b26c4bfc 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 8adae232fc..148d28a025 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -1741,18 +1741,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1772,7 +1772,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Malyan/M180/Configuration.h b/config/examples/Malyan/M180/Configuration.h index 810b541a78..32149cf7ed 100644 --- a/config/examples/Malyan/M180/Configuration.h +++ b/config/examples/Malyan/M180/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index 2aa38459a7..12371035df 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 017f2d0978..447cef9bbf 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index 527c76d8cc..b34698c6de 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index de5d37752e..937d891435 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index 132efe627f..0f39467b78 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -1719,18 +1719,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1750,7 +1750,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index c1e04a5e17..2a5c47e245 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index ce7fa3f5b1..30d17d94df 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index 5d0773789c..0f5e31f3aa 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Nextion/Configuration.h b/config/examples/Nextion/Configuration.h index d0f9712541..b9a419eeee 100644 --- a/config/examples/Nextion/Configuration.h +++ b/config/examples/Nextion/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index e1d7214039..e538460b88 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 40, 40, 40, 40 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 6.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 40, 40, 40, 40 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 6.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Polargraph/Configuration.h b/config/examples/Polargraph/Configuration.h index 2f45b2e9a7..8e4ab75935 100644 --- a/config/examples/Polargraph/Configuration.h +++ b/config/examples/Polargraph/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index ea073ed15f..253f23b047 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index 02ac34290a..3c41ae2cc6 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Prusa/MK3/Configuration.h b/config/examples/Prusa/MK3/Configuration.h index 3421442c17..6faee2f475 100644 --- a/config/examples/Prusa/MK3/Configuration.h +++ b/config/examples/Prusa/MK3/Configuration.h @@ -1746,18 +1746,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1777,7 +1777,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index 00b7fcff86..5599d8b03e 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -1737,18 +1737,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1768,7 +1768,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index 46546504f3..883a9ce53b 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h index 751cd042a5..d05ff56d97 100644 --- a/config/examples/Raiscube/A8r/Configuration.h +++ b/config/examples/Raiscube/A8r/Configuration.h @@ -1754,18 +1754,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1785,7 +1785,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 211a886604..e31b00ce92 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index 998c29515f..7e59bddb9a 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index 3b66f3d150..a175a811b6 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index bb4d008674..27c8bd92fd 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -1718,18 +1718,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1749,7 +1749,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index ab8485ee93..a9865e602e 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -1763,18 +1763,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1794,7 +1794,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index e4ccec04c0..788de70a25 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 0093436aac..dc437cb8e2 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -1727,18 +1727,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1758,7 +1758,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index 81a95f31fa..029fa23a3a 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 75af81aaba..ebd27d91e5 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -1759,18 +1759,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1790,7 +1790,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 30410061ac..f7ab9179a2 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -1759,18 +1759,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1790,7 +1790,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index ca9e93131e..73e16e23f9 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index 0911b6b130..ad0a58f5f2 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 40aee14f4b..d9d41adf43 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 8eb749c746..e57aec9b1b 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -1744,18 +1744,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1775,7 +1775,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Simulator/Configuration.h b/config/examples/Simulator/Configuration.h index 06f18640f8..e14ac63c31 100644 --- a/config/examples/Simulator/Configuration.h +++ b/config/examples/Simulator/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h index 2bf3a4704f..d78c9e8860 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h index 2e3b1223b2..9fc5c8b397 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h index 83e0fdf45d..fe45f83871 100644 --- a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h index 1d876013ce..751008daae 100644 --- a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Sunlu/S8/Configuration.h b/config/examples/Sunlu/S8/Configuration.h index 2cb25bc18d..71f8345a01 100644 --- a/config/examples/Sunlu/S8/Configuration.h +++ b/config/examples/Sunlu/S8/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration.h b/config/examples/TPARA/AXEL_TPARA/Configuration.h index 5c2d7cd3f9..c5dcef9fc7 100644 --- a/config/examples/TPARA/AXEL_TPARA/Configuration.h +++ b/config/examples/TPARA/AXEL_TPARA/Configuration.h @@ -1739,18 +1739,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1770,7 +1770,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index 33842990d9..9268c1fd2e 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 5a5f865da2..35f1253324 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index cb76aa3b92..746b0e0bda 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index b38eca7b1b..e9305e2cef 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index 5875505628..91048d8016 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index fe07e5fd6e..a7141347db 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -1759,18 +1759,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1790,7 +1790,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 106b220ecb..9c36392d06 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 691a6cebc5..6d81939d00 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -1717,18 +1717,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1748,7 +1748,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index 0029f47f47..8adadb1e54 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -1722,18 +1722,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1753,7 +1753,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 690a055e81..7334fc7d0e 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -1712,18 +1712,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1743,7 +1743,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/X5SA-2E/Configuration.h b/config/examples/Tronxy/X5SA-2E/Configuration.h index 07c2f5bb52..bb4957bf03 100644 --- a/config/examples/Tronxy/X5SA-2E/Configuration.h +++ b/config/examples/Tronxy/X5SA-2E/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 50, 50, 50, 50 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - #define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - #define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 50, 50, 50, 50 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + #define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + #define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index 82eb9499f8..44d070c2aa 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 5d8ac33ef4..7f6c35dcfa 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -1720,18 +1720,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1751,7 +1751,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Two Trees/BlueR Plus/Configuration.h b/config/examples/Two Trees/BlueR Plus/Configuration.h index f22c8bd657..1ca847bbe2 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 10 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 10 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h index b88fbe968c..7cc1d4d9a7 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h @@ -1745,18 +1745,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 10 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 10 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1776,7 +1776,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h index 5c9a0ff93b..4d9bb7c3c0 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h @@ -1750,18 +1750,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 10 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 10 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1781,7 +1781,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h index 5ba7c58343..8b072584ab 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h @@ -1749,18 +1749,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 10 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 10 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1780,7 +1780,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h index 9bde995d55..a6d5f22d75 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h @@ -1751,18 +1751,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 35, 35, 35, 35 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 35, 35, 35, 35 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1782,7 +1782,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h index 4112f05453..9ac0c65923 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h @@ -1748,18 +1748,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1779,7 +1779,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index f282fa0924..af4bd3ef51 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index a5be9b633f..d6416482b7 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Ultimaker/Ultimaker 2/Configuration.h b/config/examples/Ultimaker/Ultimaker 2/Configuration.h index 8b156ed7dd..48db390d3a 100644 --- a/config/examples/Ultimaker/Ultimaker 2/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker 2/Configuration.h @@ -1728,18 +1728,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1759,7 +1759,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h index 6f364c9354..88dd2ccd6f 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h index 4c24829237..2533273799 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF } #endif /** diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 745495af2f..5c5104bc9a 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Velleman/K8200 Upgraded/Configuration.h b/config/examples/Velleman/K8200 Upgraded/Configuration.h index 4ded505395..932c662b95 100644 --- a/config/examples/Velleman/K8200 Upgraded/Configuration.h +++ b/config/examples/Velleman/K8200 Upgraded/Configuration.h @@ -1748,18 +1748,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1779,7 +1779,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index a6afb0c935..125a06157a 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -1752,18 +1752,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1783,7 +1783,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index e663b1a38a..3905561c70 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 7f51104737..f0c080726f 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index d05b50b994..43d29a162f 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -1727,18 +1727,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1758,7 +1758,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index 54c4e92d92..f25a50b028 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 44f31f804a..2ebf62ea1c 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 7488e17110..043cdaa0ac 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 49c52f209f..5adadf0bd0 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h index 8962fa829e..1899dfdd5d 100644 --- a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Weedo/Tina2/V2/Configuration.h b/config/examples/Weedo/Tina2/V2/Configuration.h index 2f920b8870..cbf6da163a 100644 --- a/config/examples/Weedo/Tina2/V2/Configuration.h +++ b/config/examples/Weedo/Tina2/V2/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Weedo/Tina2/V3/Configuration.h b/config/examples/Weedo/Tina2/V3/Configuration.h index 53807fdb67..7d7a708bb2 100644 --- a/config/examples/Weedo/Tina2/V3/Configuration.h +++ b/config/examples/Weedo/Tina2/V3/Configuration.h @@ -1713,18 +1713,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1744,7 +1744,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index 7de8305c29..de0d604644 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index 7f03debe75..78c91baf9e 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -1714,18 +1714,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1745,7 +1745,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index dcb94dd453..d5044d4998 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index 6de7f9cb60..ab8d4548a6 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index aa74ec3757..31bda8a8b9 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -1854,18 +1854,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1885,7 +1885,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 86c260da9a..0844eb397e 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -1855,18 +1855,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1886,7 +1886,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index 9157b49aaf..8734d89b55 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -1797,18 +1797,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1828,7 +1828,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 04691ca3d6..45d701f654 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -1794,18 +1794,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1825,7 +1825,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index ce006e389d..9c4af51d83 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -1806,18 +1806,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1837,7 +1837,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h index f2056ce3b8..250a2b63d0 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h @@ -1798,18 +1798,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1829,7 +1829,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h index c9eed2af78..c3b9a45fee 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h @@ -1795,18 +1795,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1826,7 +1826,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index 44db20fa89..0f0342530e 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -1797,18 +1797,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1828,7 +1828,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h index 899f44daef..b39e05ff85 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h @@ -1797,18 +1797,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1828,7 +1828,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 9668785b53..926584b151 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -1800,18 +1800,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1831,7 +1831,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index bfd6000298..539a57238b 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -1799,18 +1799,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1830,7 +1830,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 42629bc7b2..c898b53398 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -1799,18 +1799,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1830,7 +1830,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index 8dcd2159d0..ae4d4d0bab 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -1795,18 +1795,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1826,7 +1826,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index 9cb2d77ae8..718b501d71 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -1795,18 +1795,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1826,7 +1826,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index 67bcdd9634..a6a1fcef85 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -1795,18 +1795,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1826,7 +1826,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index d095655f91..d6fb648a6a 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -1795,18 +1795,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - #define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + #define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1826,7 +1826,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 4c19e657a4..3d0dbba070 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -1797,18 +1797,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1828,7 +1828,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index e0e523c012..dbdca9badf 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -1802,18 +1802,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1833,7 +1833,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 21b2a3be86..7b3b2d44a3 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -1797,18 +1797,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1828,7 +1828,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index 365d9686a0..2dcaf88f1b 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -1762,18 +1762,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1793,7 +1793,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index e129fd9c3e..7f77137b97 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -1798,18 +1798,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1829,7 +1829,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index faa60e5eb2..4169bda202 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -1797,18 +1797,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1828,7 +1828,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index 7f6e2406f1..6e8c52168f 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -1796,18 +1796,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1827,7 +1827,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index 66fd590756..f5ae8f2fd4 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -1799,18 +1799,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1830,7 +1830,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index 90129bddd4..310f2998b7 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -1818,18 +1818,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1849,7 +1849,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index a8b3d77f37..7499ec49bb 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -1802,18 +1802,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1833,7 +1833,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 9a9f5f0832..43b058b4ac 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -1721,18 +1721,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1752,7 +1752,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h index 6ba3c71d26..57f022b461 100644 --- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h +++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h @@ -1715,18 +1715,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1746,7 +1746,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 3fc13768da..9fffb19493 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -1716,18 +1716,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1747,7 +1747,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /** diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index 259867c31d..d8caac11c5 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -1720,18 +1720,18 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LEVEL_BED_CORNERS +//#define LCD_BED_TRAMMING -#if ENABLED(LEVEL_BED_CORNERS) - #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets - #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points - #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points - //#define LEVEL_CENTER_TOO // Move to the center after the last corner - //#define LEVEL_CORNERS_USE_PROBE - #if ENABLED(LEVEL_CORNERS_USE_PROBE) - #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1 - #define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify - //#define LEVEL_CORNERS_AUDIO_FEEDBACK +#if ENABLED(LCD_BED_TRAMMING) + #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets + #define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define BED_TRAMMING_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points + //#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner + //#define BED_TRAMMING_USE_PROBE + #if ENABLED(BED_TRAMMING_USE_PROBE) + #define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm) + #define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify + //#define BED_TRAMMING_AUDIO_FEEDBACK #endif /** @@ -1751,7 +1751,7 @@ * | 1 2 | | 1 4 | | 1 2 | | 2 | * LF --------- RF LF --------- RF LF --------- RF LF --------- RF */ - #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB } + #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB } #endif /**