diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h index b37620e98c..11ba0f26c4 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h @@ -588,8 +588,8 @@ #define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) - //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) - //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + #define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + #define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) // Set/get with gcode: M301 E[extruder number, 0-2] @@ -717,7 +717,7 @@ * Note: For Bowden Extruders make this large enough to allow load/unload. */ #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH 200 +#define EXTRUDE_MAXLENGTH 705 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -927,14 +927,14 @@ * Override with M92 * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]] */ -#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.7402, 78.7402, 533.3333, 876.6687 } +#define DEFAULT_AXIS_STEPS_PER_UNIT {81.3800, 78.7900, 533.3333, 883.84346} // default { 78.7402, 78.7402, 533.3333, 876.6687 } /** * Default Max Feed Rate (mm/s) * Override with M203 * X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]] */ -#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } +#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2 #if ENABLED(LIMITED_MAX_FR_EDITING) @@ -974,10 +974,10 @@ * When changing speed and direction, if the difference is less than the * value set here, it may happen instantaneously. */ -//#define CLASSIC_JERK +#define CLASSIC_JERK #if ENABLED(CLASSIC_JERK) - #define DEFAULT_XJERK 10.0 - #define DEFAULT_YJERK 10.0 + #define DEFAULT_XJERK 7.0 + #define DEFAULT_YJERK 7.0 #define DEFAULT_ZJERK 0.3 //#define DEFAULT_IJERK 0.3 //#define DEFAULT_JJERK 0.3 @@ -1014,7 +1014,7 @@ * * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained */ -//#define S_CURVE_ACCELERATION +#define S_CURVE_ACCELERATION //=========================================================================== //============================= Z Probe Options ============================= @@ -1364,7 +1364,7 @@ //#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding. -//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z +#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z // Direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1] @@ -1378,8 +1378,8 @@ // @section machine // The size of the printable area -#define X_BED_SIZE 205 -#define Y_BED_SIZE 208 +#define X_BED_SIZE 210 +#define Y_BED_SIZE 210 // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS 0 @@ -1387,7 +1387,7 @@ #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE -#define Z_MAX_POS 200 +#define Z_MAX_POS 205 //#define I_MIN_POS 0 //#define I_MAX_POS 50 //#define J_MIN_POS 0 @@ -1754,7 +1754,7 @@ #endif // Homing speeds (mm/min) -#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) } +#define HOMING_FEEDRATE_MM_M { (90*60), (90*60), (12*60) } // Validate that endstops are triggered on homing moves #define VALIDATE_HOMING_ENDSTOPS @@ -1865,7 +1865,7 @@ // Preheat Constants - Up to 5 are supported without changes // #define PREHEAT_1_LABEL "PLA" -#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_HOTEND 210 #define PREHEAT_1_TEMP_BED 70 #define PREHEAT_1_TEMP_CHAMBER 35 #define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 @@ -1887,16 +1887,16 @@ * P1 Raise the nozzle always to Z-park height. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. */ -//#define NOZZLE_PARK_FEATURE +#define NOZZLE_PARK_FEATURE #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z_raise } - #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 3), (Y_MIN_POS + 3), 50 } //#define NOZZLE_PARK_X_ONLY // X move only is required to park //#define NOZZLE_PARK_Y_ONLY // Y move only is required to park #define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) - #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) + #define NOZZLE_PARK_Z_FEEDRATE 30 // (mm/s) Z axis feedrate (not used for delta printers) #endif /** diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h index 8131031956..e00be7b9aa 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration_adv.h @@ -482,7 +482,7 @@ * Hotend Idle Timeout * Prevent filament in the nozzle from charring and causing a critical jam. */ -//#define HOTEND_IDLE_TIMEOUT +#define HOTEND_IDLE_TIMEOUT #if ENABLED(HOTEND_IDLE_TIMEOUT) #define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection @@ -2469,38 +2469,38 @@ * * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) - #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. - #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + #define PAUSE_PARK_RETRACT_FEEDRATE 1800 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 50 // (mm) Initial retract. // This short retract is done immediately, before parking the nozzle. - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 2500 // (mm/s) Unload filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 700 // (mm) The length of filament for a complete unload. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. // Set to 0 for manual unloading. #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. - #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 10 // (mm) Slow length, to allow time to insert material. // 0 to disable start loading and skip to fast load only - #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 1800 // (mm/s) Load filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 600 // (mm) Load length of filament, from extruder gear to nozzle. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. - #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 150 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. // Set to 0 for manual extrusion. // Filament can be extruded repeatedly from the Filament Change menu // until extrusion is consistent, and to purge old filament. - #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. - //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + #define ADVANCED_PAUSE_RESUME_PRIME 20 // (mm) Extra distance to prime nozzle after returning from park. + #define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. // Filament Unload does a Retract, Delay, and Purge first: - #define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length. - #define FILAMENT_UNLOAD_PURGE_DELAY 5000 // (ms) Delay for the filament to cool after retract. - #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + #define FILAMENT_UNLOAD_PURGE_RETRACT 0 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_PURGE_DELAY 2000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 20 // (mm) An unretract is done, then this length is purged. #define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. @@ -2509,10 +2509,10 @@ //#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again. //#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing. - //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. //#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change - //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) #endif