diff --git a/config/examples/Index/REV_03/Configuration.h b/config/examples/Opulo/Lumen_REV3/Configuration.h
similarity index 99%
rename from config/examples/Index/REV_03/Configuration.h
rename to config/examples/Opulo/Lumen_REV3/Configuration.h
index 0cf71402dc..d6f45d0d47 100644
--- a/config/examples/Index/REV_03/Configuration.h
+++ b/config/examples/Opulo/Lumen_REV3/Configuration.h
@@ -98,7 +98,7 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_INDEX_REV03
+  #define MOTHERBOARD BOARD_OPULO_LUMEN_REV3
 #endif
 
 /**
@@ -991,7 +991,7 @@
  * Override with M92
  *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 40, 40, 40, 4.44, 4.44, 40 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 1280, 1280, 40, 4.44, 4.44, 40 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -1436,7 +1436,7 @@
  */
 //#define Z_IDLE_HEIGHT Z_HOME_POS
 
-//#define Z_HOMING_HEIGHT  31.5      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                                   // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
 
 #define Z_AFTER_HOMING  31.5      // (mm) Height to move to after homing Z
@@ -1763,7 +1763,7 @@
 //#define LCD_BED_TRAMMING
 
 #if ENABLED(LCD_BED_TRAMMING)
-  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
+  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 }  // (mm) Left, Front, Right, Back insets
   #define BED_TRAMMING_HEIGHT      0.0        // (mm) Z height of nozzle at leveling points
   #define BED_TRAMMING_Z_HOP       4.0        // (mm) Z height of nozzle between leveling points
   //#define BED_TRAMMING_INCLUDE_CENTER       // Move to the center after the last corner
diff --git a/config/examples/Index/REV_03/Configuration_adv.h b/config/examples/Opulo/Lumen_REV3/Configuration_adv.h
similarity index 99%
rename from config/examples/Index/REV_03/Configuration_adv.h
rename to config/examples/Opulo/Lumen_REV3/Configuration_adv.h
index d432db02c6..eca805e66c 100644
--- a/config/examples/Index/REV_03/Configuration_adv.h
+++ b/config/examples/Opulo/Lumen_REV3/Configuration_adv.h
@@ -2711,7 +2711,7 @@
   #if AXIS_IS_TMC(X)
     #define X_CURRENT       800        // (mA) RMS current. Multiply by 1.414 for peak current.
     #define X_CURRENT_HOME  X_CURRENT  // (mA) RMS current for sensorless homing
-    #define X_MICROSTEPS      8        // 0..256
+    #define X_MICROSTEPS      256      // 0..256
     #define X_RSENSE          0.11
     #define X_CHAIN_POS      -1        // -1..0: Not chained. 1: MCU MOSI connected. 2: Next in chain, ...
     //#define X_INTERPOLATE  true      // Enable to override 'INTERPOLATE' for the X axis
@@ -2731,7 +2731,7 @@
   #if AXIS_IS_TMC(Y)
     #define Y_CURRENT       800
     #define Y_CURRENT_HOME  Y_CURRENT
-    #define Y_MICROSTEPS      8
+    #define Y_MICROSTEPS      256
     #define Y_RSENSE          0.11
     #define Y_CHAIN_POS      -1
     //#define Y_INTERPOLATE  true
@@ -3843,7 +3843,7 @@
 #define FASTER_GCODE_PARSER
 
 #if ENABLED(FASTER_GCODE_PARSER)
-  #define GCODE_QUOTED_STRINGS  // Support for quoted string parameters
+  #define GCODE_QUOTED_STRINGS    // Support for quoted string parameters
 #endif
 
 // Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)