diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 8f489cceae..7e2c636705 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index 866e408b1a..58d4de8302 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index 5c5345dead..abe0b79c9b 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index 02f0a156ce..35a3284be6 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 5c30ca17bc..75ddce8169 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -971,10 +971,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index ff68f7bad3..cc87880bd8 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -1016,10 +1016,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 053c8a70ca..82321ba3d3 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -1018,10 +1018,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 393d409509..b8f63f68e4 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index b60e309b5a..793e397d07 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index f8a9ba6810..0cd0f9fae1 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index b9a74b6320..0c32bbeb34 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index ecc49d21c8..b70e0950a0 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -977,10 +977,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 9fdfa16de4..eac2366936 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -963,10 +963,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 8191486215..f5c31411f1 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h index 407e39bd1a..2c9e0cbf2a 100644 --- a/config/examples/Anet/A9/Configuration.h +++ b/config/examples/Anet/A9/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index b1deb98ba4..a60b8b17f3 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h index 86309eaa28..e33c64dc25 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h index 5cd29a69df..492623940d 100644 --- a/config/examples/Anet/E16/Stock/Configuration.h +++ b/config/examples/Anet/E16/Stock/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h index 547601ae32..a65710f08a 100644 --- a/config/examples/Anet/ET4/Configuration.h +++ b/config/examples/Anet/ET4/Configuration.h @@ -966,10 +966,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h index 8b0bb9e2c2..3236c65ca5 100644 --- a/config/examples/AnyCubic/Chiron/Configuration.h +++ b/config/examples/AnyCubic/Chiron/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h index 039eabb80b..b6f79dd305 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h index 624e65e604..c0d2f179a2 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h index 22400548b7..d889912ce3 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration.h @@ -974,10 +974,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 1f0e2da607..60ba4ec161 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 0bccc2f714..38360d9d94 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Artillery/Genius/Configuration.h b/config/examples/Artillery/Genius/Configuration.h index ade52ab606..af5ffa58e9 100644 --- a/config/examples/Artillery/Genius/Configuration.h +++ b/config/examples/Artillery/Genius/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Artillery/Sidewinder X1/Configuration.h b/config/examples/Artillery/Sidewinder X1/Configuration.h index e331c96041..8dc83c2aa5 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h index 0ca399bf4b..17c3d31cff 100644 --- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h @@ -976,10 +976,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 6f2a1d4074..a305e12621 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 15455f397c..f78357d090 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 0546e72f6d..429db1656d 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BIQU/B1-BLTouch/Configuration.h b/config/examples/BIQU/B1-BLTouch/Configuration.h index 1218b5560d..8fe9ba7cbf 100644 --- a/config/examples/BIQU/B1-BLTouch/Configuration.h +++ b/config/examples/BIQU/B1-BLTouch/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BIQU/B1/Configuration.h b/config/examples/BIQU/B1/Configuration.h index 32550c8c7a..22318f4419 100644 --- a/config/examples/BIQU/B1/Configuration.h +++ b/config/examples/BIQU/B1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 8dee9a3659..6d151cc23b 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 7788285efc..2460035303 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -974,10 +974,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 0fce27ff7b..a243323323 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index 70f5b02301..4ce69a2770 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index dd5a072a1e..4a39613acb 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -976,10 +976,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index 887a80255f..82346ac539 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 07a918ee80..5eec9fa38d 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index d40ad3943b..2f9d7a6493 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h index 38f87d388a..0ef0724f8c 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h @@ -969,10 +969,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h index dbfab1ac5e..344b423c70 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h index 8a5b561b5b..5010673ec1 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h index 4a296c82c2..9daaa874d3 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index bcc1802e11..6aeb8e9789 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -975,10 +975,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h index 458f1fe5ae..75c07625f8 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h index fe457b68e4..524afe4b94 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h index 5f6de84ad1..2c1885c806 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h index 289235acc2..10b9b21609 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index e761c0ee2b..ca3752b7c7 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 31c14c5209..d39c70a87f 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h index 76ad6e1b39..cfb6c68da7 100644 --- a/config/examples/Creality/CR-6 SE/Configuration.h +++ b/config/examples/Creality/CR-6 SE/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 356532dc15..6db50e4197 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index a4211a93e0..43c43af61c 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h index 39b9170fb3..e53473178c 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index eca35a4a40..a0a3c6d39e 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h index 13c47d3fba..58f22ddb19 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h index 6ceba43eba..96e25da0d8 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h index 181ced3083..48a0c2f9eb 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h index 85d9fb04c3..ea5a7acf09 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3 V2/Configuration.h b/config/examples/Creality/Ender-3 V2/Configuration.h index 210ec12fc1..2343601ee9 100644 --- a/config/examples/Creality/Ender-3 V2/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h index 922c88be13..6089792de7 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h index bacfe070ba..15add7915b 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h index 9182a5d8fd..e0e6ffecae 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h index f26adda49c..863fd5df69 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index 4b91ddcc07..def025727c 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index 034a400ed9..0b1ba3bc97 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index a797e32d09..98dd98b800 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index 6d58ddb3e5..ae1b2ff49e 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h index 122e007d2d..0e03f90203 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h index 924b412236..d3f76a8a13 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index de6a4f63b1..10d6fa4d74 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 1c5d59e3aa..a0d80d898c 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index 5a8a8717a7..cade3836f7 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index 1530ca7fee..29f402cd93 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index 9e406c68cc..d719c4b640 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -966,10 +966,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h index f6e1df27c0..616875325a 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h index 1c2cc2e223..86d6a8f879 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index 57ea89458e..4ce438f20f 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h index 1b06343b8e..552520bb80 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration.h @@ -968,10 +968,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index 6a93271142..9a0e306ce5 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h index 187cf461a9..e885f30fc9 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h index 9b50338511..264f6b8d21 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h index 72c44fa02c..8cdd31e30d 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index 4c1a84e4d8..babfed6075 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -990,10 +990,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h index 458b472679..3b1a30b274 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index 502383ad6b..ca52ee1307 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h index bcbda97b13..1e36e99411 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h index 227636a1c3..ba0781b90d 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 001bb9b517..65cae6af8a 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index 8791ab0bb3..999e891418 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -963,10 +963,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index a657929e7d..f1ebc1540b 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 1fd6aa8933..f73f4b35e6 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -965,10 +965,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 285aea3f1f..3502cb2811 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index aa22164782..4c76fca18f 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index d1cade18d6..5d0ea011ae 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index d87ab7bf9c..3db438d59c 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index ab16f9c185..a26eed9fab 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index 68d4e6a05b..a6fdf2b4fd 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index bd253efc52..afbca87115 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index 924c8edf8b..7b5ea11399 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index d2f57c5d1a..6fd9d0c6d9 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index c88516e352..2eb15b38af 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -1051,10 +1051,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 406bd3c619..71a50b1a98 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index a116e9f582..e2764d8986 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index 36bb6606c5..3092aab0d6 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index cd52516588..367ca64967 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index 6d4f72d185..425096b70a 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A10T/Configuration.h b/config/examples/Geeetech/A10T/Configuration.h index 8514b21e35..2768bc9873 100644 --- a/config/examples/Geeetech/A10T/Configuration.h +++ b/config/examples/Geeetech/A10T/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index c1e52ff5d8..b1d85a0503 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index dfc9ed469a..92501ba947 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index a1518baf42..0009c930c0 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index ece23fe8f9..ba250d3245 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -958,10 +958,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index a0fcc0205c..19d77744c4 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -958,10 +958,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index 9d0e16445d..00ac17e4ce 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index 599d879631..bd4865320d 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index fcaa3b98d3..076bf13865 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -965,10 +965,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 84103737bc..314bbf9a4f 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index acd15453b8..e5144a5a66 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -958,10 +958,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 8476f6fa31..11aaf53f32 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index afff92351a..8237882aa5 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index ef5eef588d..f009ea579a 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index 640210da8c..2e85450737 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -970,10 +970,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 27b6da9768..b4e3d287ac 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -971,10 +971,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 0abe7c7875..f8a0f1da16 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -970,10 +970,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 0a3142640d..39c2cf0147 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 38f08f76f7..7278a9944f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 23156fd456..09d42e9d25 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -958,10 +958,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 761d585055..ed298cf0c1 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h index fce4550c1b..3cd4f24d63 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index bb398f8e21..90bd05c795 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index a4c97c01a1..b54058f3f7 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index ce4f756288..0d41707171 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -968,10 +968,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index 543f3398a9..02eccd7218 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index 0f38f0b915..03ff92f1ea 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index 1562e81c31..7975799f65 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index b5f114cd2a..0010104a3e 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h index deeb3252a1..ffc2c3c092 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h @@ -966,10 +966,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 11a3e229f7..ba79c00d57 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 699669b696..7e20b0d09f 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -980,10 +980,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index a5402a42d4..e0712350fe 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -966,10 +966,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index cb7bd73d54..964a9cf20b 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index 3d973b81d4..849d2d7fa9 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 24f11c9472..8da8cf3200 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index 40ada9a940..615d8ded3f 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index a5162d6ecd..8d07bdd098 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index d974e8965f..93bcf54124 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index 1ad88765cf..f8e6f06339 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index bb80aaa72c..d04886f8ca 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index b7ac5db953..8affb1ff5d 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index c641bb209d..6d07fc83da 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index 6dc26289fa..673eab14a3 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index 8768036191..44d7b39043 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -963,10 +963,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h index e7e67570bd..77376198eb 100644 --- a/config/examples/Raiscube/A8r/Configuration.h +++ b/config/examples/Raiscube/A8r/Configuration.h @@ -978,10 +978,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index c515f98cff..5914bff24b 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index 6c5e11722c..886817562e 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index eb5084317c..3844456217 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 2c95421d81..869fabf963 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 3b3355b552..509b75d9d9 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -1000,10 +1000,20 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 07617d6b8f..d3c8055680 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index d966fea81e..f729ec3c57 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -975,10 +975,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index 9ed1bc78fd..93a1befb4e 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index d542ace88e..aab6d2fdab 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -1001,10 +1001,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 5f224d1233..472ada0be2 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -1001,10 +1001,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index 55792c2306..6d247b87e8 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index e22ce55de7..6559211685 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 73fa9f0483..080a37c214 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index ef91190434..af348d2c84 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -991,10 +991,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Sovol/SV-01/Configuration.h b/config/examples/Sovol/SV-01/Configuration.h index 649df090fd..d7c28124b5 100644 --- a/config/examples/Sovol/SV-01/Configuration.h +++ b/config/examples/Sovol/SV-01/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index dfa37f52a8..668363ef8e 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 95a37410b4..96345a1e1f 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index a1d6a29810..2770f7d3a1 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index a14efa0f14..4b013bdc6a 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index 651c9e0ca7..fa88d27ae3 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 8182b54c25..250f392a8e 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 2a669af1ae..13927c354f 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -1001,10 +1001,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 69095a7363..c245afabc6 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index c30c3b03c9..af11548f3c 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index f4c32237e9..b5fb42df94 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -969,10 +969,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index c4aa07321c..f41f48dbb8 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index 383d429c16..5400e31fe0 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 5ef83c1d4f..7dfa436edf 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h index 15701e193e..1b0e104a99 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h @@ -978,10 +978,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h index a106379cb2..0486062842 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h @@ -979,10 +979,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h index dca9ff761b..cc16ead811 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h @@ -982,10 +982,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h index 16c266193a..7fb878a686 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h @@ -959,10 +959,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Two Trees/Sapphire/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire/Sapphire Plus V2/Configuration.h index b8ff50d59e..878de0ea70 100644 --- a/config/examples/Two Trees/Sapphire/Sapphire Plus V2/Configuration.h +++ b/config/examples/Two Trees/Sapphire/Sapphire Plus V2/Configuration.h @@ -973,10 +973,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 32da743c14..be319c82d2 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index cd267a711d..b1a6b485dd 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 87d2f2ebe9..11f38d04c2 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index 15fe6f3bc3..30c5d02ebe 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -980,10 +980,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 6715ce6e20..cf3f5da4c2 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 56ca8fd073..c9f19e5748 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 2f042f041b..5ceb4a12de 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -974,10 +974,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index a1eadd86d2..96a110f3bc 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -962,10 +962,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index d97e6e5554..734e19e064 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 2b8a1ffe74..6a2c95357c 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index ea415ffe56..826ead6f90 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index 8e85eabb41..d539684505 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -961,10 +961,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index 02a9274e8b..71efd50e8e 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index e54aab45db..b8e9d4bfa4 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -964,10 +964,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index fc490127d6..cf3b5baee8 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -960,10 +960,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index ad9746b4fc..ce738a1fc5 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -1102,10 +1102,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 7b943c751f..c1ef57217b 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -1099,10 +1099,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index 2f4d9320f4..2fc5e38f11 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -1059,10 +1059,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 4bcc53c693..f44d26c104 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -1058,10 +1058,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index c91a59dd53..2dfd2f3290 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -1070,10 +1070,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h index 07d06da666..d9c52df48c 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h @@ -1057,10 +1057,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h index 51df8ef2ef..bda78b5bad 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h @@ -1058,10 +1058,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index 5fa9228409..1a010ba997 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -1059,10 +1059,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h index 6c22b499a8..2b3985e63f 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h @@ -1067,10 +1067,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 1d0afcc8e9..e70cbcd6e9 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -1062,10 +1062,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index b067a79bd9..106f273cfd 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -1061,10 +1061,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index fc255c4d67..1cefe92070 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -1061,10 +1061,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index 35712430fc..fc210a73c2 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -1057,10 +1057,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index a4bb425ce6..d36781c1ab 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -1057,10 +1057,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index 3541045306..20ec621c11 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -1057,10 +1057,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index be72c735af..c797a74b10 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -1057,10 +1057,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index ed80ae0625..1251801055 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -1059,10 +1059,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index c841f974e7..93d6e56e7e 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -1064,10 +1064,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 76a29e962b..e0aa9192f7 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -1059,10 +1059,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index 59b5a9e8ab..a709ab470e 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -1024,10 +1024,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 8195a12fa8..7a858e29df 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -1060,10 +1060,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 53fad20a35..a90a17f605 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -1059,10 +1059,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index f28c637afd..886182b174 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -1057,10 +1057,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index 5d62ac636b..088413c0d3 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -1061,10 +1061,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index e3ebd2a301..2e99e5d146 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -1075,10 +1075,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 442d9b5705..229b39271e 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -1064,10 +1064,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index dc1a48b4f1..1c22acb01d 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index f65521d263..26c8da4d6f 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -963,10 +963,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index 8c6f6654ad..d0bbbb4b63 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -967,10 +967,20 @@ /** * Nozzle-to-Probe offsets { X, Y, Z } * - * - Use a caliper or ruler to measure the distance from the tip of + * X and Y offset + * Use a caliper or ruler to measure the distance from the tip of * the Nozzle to the center-point of the Probe in the X and Y axes. + * + * Z offset * - For the Z offset use your best known value and adjust at runtime. - * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - Common probes trigger below the nozzle and have negative values for Z offset. + * - Probes triggering above the nozzle height are uncommon but do exist. When using + * probes such as this, carefully set Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES + * to avoid collisions during probing. + * + * Tune and Adjust + * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc. + * - PROBE_OFFSET_WIZARD (configuration_adv.h) can be used for setting the Z offset. * * Assuming the typical work area orientation: * - Probe to RIGHT of the Nozzle has a Positive X offset