🚸 More PID Edit menus

MarlinFirmware/Marlin#23983

config/default/Configuration.h

@@ -619,8 +619,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -767,6 +765,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -669,8 +669,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -831,6 +829,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Alfawise/U20/Configuration.h

@@ -669,8 +669,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -832,6 +830,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AliExpress/CL-260/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/A2/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/A2plus/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/A6/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/A8/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -765,6 +763,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/A8plus/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/A9/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/E10/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/E16/BTT SKR 1.3/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/E16/Stock/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET4+/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -768,6 +766,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET4-Pro/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -768,6 +766,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET4/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -768,6 +766,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET4X/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -768,6 +766,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET5-Pro/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET5/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Anet/ET5X/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AnyCubic/Chiron/Configuration.h

@@ -618,8 +618,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -766,6 +764,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AnyCubic/i3 Mega/Configuration.h

@@ -635,8 +635,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -783,6 +781,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/AnyCubic/i3/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/ArmEd/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Genius Pro/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 25 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Genius/BLTouch/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Genius/V1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Hornet/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 25 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -777,6 +775,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Sidewinder X1/V1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Artillery/Sidewinder X2/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 25 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Azteeg/X5GT/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIBO/TouchX/default/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -718,6 +716,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIQU/B1 - SKR 1.4/Configuration.h

@@ -616,8 +616,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIQU/B1 - SKR 2/Configuration.h

@@ -616,8 +616,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIQU/B1 SE Plus/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -760,6 +758,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIQU/BX/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BIQU/Thunder Standard/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BQ/Hephestos/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BQ/Hephestos_2/Configuration.h

@@ -622,8 +622,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -776,6 +774,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/BQ/WITBOX/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/CTC/A13/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/CTC/Bizer/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Cartesio/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -778,6 +776,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Copymaster3D/300/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Copymaster3D/400/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Copymaster3D/500/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -623,8 +623,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -770,6 +768,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h

@@ -623,8 +623,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -771,6 +769,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 V2/Configuration.h

@@ -621,8 +621,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -771,6 +769,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10 V3/Configuration.h

@@ -621,8 +621,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -771,6 +769,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -761,6 +759,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10/CrealityV1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-10S/CrealityV1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-20/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-30 PrintMill/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-6 SE/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/CR-8/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-2/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Max/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -764,6 +762,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 S1/Configuration.h

@@ -615,8 +615,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -761,6 +759,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -763,6 +761,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -761,6 +759,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -761,6 +759,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -761,6 +759,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -762,6 +760,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder

config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h

@@ -614,8 +614,6 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -761,6 +759,9 @@
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
 #endif
 
 // @section extruder