mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2025-07-07 15:07:34 -06:00
Scott Lahteine
parent
c0e4a07015
commit
48ffab7d02
599 changed files with 40103 additions and 8744 deletions
|
|
@ -114,6 +114,7 @@
|
|||
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
|
||||
*/
|
||||
#define BAUDRATE 250000
|
||||
|
||||
//#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate
|
||||
|
||||
/**
|
||||
|
|
@ -135,7 +136,7 @@
|
|||
* | | [O] RX |
|
||||
* `------------´---------------------´
|
||||
*/
|
||||
//#define BAUDRATE_2 250000 // Enable to override BAUDRATE
|
||||
//#define BAUDRATE_2 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
|
||||
|
||||
/**
|
||||
* Select a third serial port on the board to use for communication with the host.
|
||||
|
|
@ -143,7 +144,7 @@
|
|||
* :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
|
||||
*/
|
||||
//#define SERIAL_PORT_3 1
|
||||
//#define BAUDRATE_3 250000 // Enable to override BAUDRATE
|
||||
//#define BAUDRATE_3 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
|
||||
|
||||
// Enable the Bluetooth serial interface on AT90USB devices
|
||||
//#define BLUETOOTH
|
||||
|
|
@ -402,7 +403,7 @@
|
|||
//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
|
||||
//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
|
||||
|
||||
// @section machine
|
||||
// @section psu control
|
||||
|
||||
/**
|
||||
* Power Supply Control
|
||||
|
|
@ -638,6 +639,8 @@
|
|||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
|
||||
// @section hotend temp
|
||||
|
||||
// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model.
|
||||
// temperature control. Disable both for bang-bang heating.
|
||||
#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning
|
||||
|
|
@ -648,7 +651,8 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
// POWERwasp
|
||||
|
|
@ -671,6 +675,7 @@
|
|||
* Use a physical model of the hotend to control temperature. When configured correctly
|
||||
* this gives better responsiveness and stability than PID and it also removes the need
|
||||
* for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 T to autotune the model.
|
||||
* @section mpctemp
|
||||
*/
|
||||
#if ENABLED(MPCTEMP)
|
||||
//#define MPC_EDIT_MENU // Add MPC editing to the "Advanced Settings" menu. (~1300 bytes of flash)
|
||||
|
|
@ -738,7 +743,7 @@
|
|||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -766,6 +771,7 @@
|
|||
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use chamber PID until someone else verifies that your hardware works.
|
||||
* @section chamber temp
|
||||
*/
|
||||
//#define PIDTEMPCHAMBER
|
||||
//#define CHAMBER_LIMIT_SWITCHING
|
||||
|
|
@ -780,7 +786,7 @@
|
|||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
|
|
@ -794,7 +800,6 @@
|
|||
#endif // PIDTEMPCHAMBER
|
||||
|
||||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
|
|
@ -804,7 +809,7 @@
|
|||
//#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
* Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
|
||||
|
|
@ -872,6 +877,8 @@
|
|||
#define POLAR_SEGMENTS_PER_SECOND 5
|
||||
#endif
|
||||
|
||||
// @section delta
|
||||
|
||||
// Enable for DELTA kinematics and configure below
|
||||
//#define DELTA
|
||||
#if ENABLED(DELTA)
|
||||
|
|
@ -931,6 +938,8 @@
|
|||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
|
||||
#endif
|
||||
|
||||
// @section scara
|
||||
|
||||
/**
|
||||
* MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
|
||||
* Implemented and slightly reworked by JCERNY in June, 2014.
|
||||
|
|
@ -974,6 +983,8 @@
|
|||
|
||||
#endif
|
||||
|
||||
// @section tpara
|
||||
|
||||
// Enable for TPARA kinematics and configure below
|
||||
//#define AXEL_TPARA
|
||||
#if ENABLED(AXEL_TPARA)
|
||||
|
|
@ -1000,6 +1011,8 @@
|
|||
#define PSI_HOMING_OFFSET 0
|
||||
#endif
|
||||
|
||||
// @section machine
|
||||
|
||||
// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
|
||||
//#define ARTICULATED_ROBOT_ARM
|
||||
|
||||
|
|
@ -1011,7 +1024,7 @@
|
|||
//============================== Endstop Settings ===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
// @section endstops
|
||||
|
||||
// Specify here all the endstop connectors that are connected to any endstop or probe.
|
||||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||||
|
|
@ -1681,7 +1694,7 @@
|
|||
//#define V_HOME_DIR -1
|
||||
//#define W_HOME_DIR -1
|
||||
|
||||
// @section machine
|
||||
// @section geometry
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 261
|
||||
|
|
@ -2141,7 +2154,7 @@
|
|||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// @section extras
|
||||
// @section eeprom
|
||||
|
||||
/**
|
||||
* EEPROM
|
||||
|
|
@ -2161,6 +2174,8 @@
|
|||
//#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
|
||||
#endif
|
||||
|
||||
// @section host
|
||||
|
||||
//
|
||||
// Host Keepalive
|
||||
//
|
||||
|
|
@ -2171,6 +2186,8 @@
|
|||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||||
#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
|
||||
|
||||
// @section units
|
||||
|
||||
//
|
||||
// G20/G21 Inch mode support
|
||||
//
|
||||
|
|
@ -2198,6 +2215,8 @@
|
|||
#define PREHEAT_2_TEMP_CHAMBER 35
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
// @section motion
|
||||
|
||||
/**
|
||||
* Nozzle Park
|
||||
*
|
||||
|
|
@ -2296,6 +2315,8 @@
|
|||
|
||||
#endif
|
||||
|
||||
// @section host
|
||||
|
||||
/**
|
||||
* Print Job Timer
|
||||
*
|
||||
|
|
@ -2322,6 +2343,8 @@
|
|||
*/
|
||||
#define PRINTJOB_TIMER_AUTOSTART
|
||||
|
||||
// @section stats
|
||||
|
||||
/**
|
||||
* Print Counter
|
||||
*
|
||||
|
|
@ -2339,6 +2362,8 @@
|
|||
#define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
|
||||
#endif
|
||||
|
||||
// @section security
|
||||
|
||||
/**
|
||||
* Password
|
||||
*
|
||||
|
|
@ -2374,7 +2399,7 @@
|
|||
//============================= LCD and SD support ============================
|
||||
//=============================================================================
|
||||
|
||||
// @section lcd
|
||||
// @section interface
|
||||
|
||||
/**
|
||||
* LCD LANGUAGE
|
||||
|
|
@ -2530,6 +2555,7 @@
|
|||
//======================== LCD / Controller Selection =========================
|
||||
//======================== (Character-based LCDs) =========================
|
||||
//=============================================================================
|
||||
// @section lcd
|
||||
|
||||
//
|
||||
// RepRapDiscount Smart Controller.
|
||||
|
|
@ -3175,7 +3201,7 @@
|
|||
//=============================== Extra Features ==============================
|
||||
//=============================================================================
|
||||
|
||||
// @section extras
|
||||
// @section fans
|
||||
|
||||
// Set number of user-controlled fans. Disable to use all board-defined fans.
|
||||
// :[1,2,3,4,5,6,7,8]
|
||||
|
|
@ -3199,14 +3225,18 @@
|
|||
// duty cycle is attained.
|
||||
//#define SOFT_PWM_DITHER
|
||||
|
||||
// @section extras
|
||||
|
||||
// Support for the BariCUDA Paste Extruder
|
||||
//#define BARICUDA
|
||||
|
||||
// @section lights
|
||||
|
||||
// Temperature status LEDs that display the hotend and bed temperature.
|
||||
// If all hotends, bed temperature, and target temperature are under 54C
|
||||
// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
|
||||
//#define TEMP_STAT_LEDS
|
||||
|
||||
// Support for the BariCUDA Paste Extruder
|
||||
//#define BARICUDA
|
||||
|
||||
// Support for BlinkM/CyzRgb
|
||||
//#define BLINKM
|
||||
|
||||
|
|
@ -3292,6 +3322,8 @@
|
|||
#define PRINTER_EVENT_LEDS
|
||||
#endif
|
||||
|
||||
// @section servos
|
||||
|
||||
/**
|
||||
* Number of servos
|
||||
*
|
||||
|
|
|
|||
|
|
@ -32,6 +32,24 @@
|
|||
*/
|
||||
#define CONFIGURATION_ADV_H_VERSION 02010100
|
||||
|
||||
// @section develop
|
||||
|
||||
/**
|
||||
* Configuration Dump to JSON and INI format
|
||||
*
|
||||
* Dump the configuration as part of the build. (See signature.py)
|
||||
* Output files are saved with the build (e.g., .pio/build/mega2560).
|
||||
*
|
||||
* See `build_all_examples --ini` as an example of config.ini archiving.
|
||||
*
|
||||
* 1 = marlin_config.json - Dictionary containing the configuration.
|
||||
* This file is also generated for CONFIGURATION_EMBEDDING.
|
||||
* 2 = config.ini - File format for PlatformIO preprocessing.
|
||||
* 3 = schema.json - The entire configuration schema. (13 = pattern groups)
|
||||
* 4 = schema.yml - The entire configuration schema.
|
||||
*/
|
||||
//#define CONFIG_DUMP // :[1:'JSON', 2:'config.ini', 3:'schema.json', 4:'schema.yml']
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
|
@ -2558,6 +2576,8 @@
|
|||
#endif
|
||||
#endif // HAS_MULTI_EXTRUDER
|
||||
|
||||
// @section advanced pause
|
||||
|
||||
/**
|
||||
* Advanced Pause for Filament Change
|
||||
* - Adds the G-code M600 Filament Change to initiate a filament change.
|
||||
|
|
@ -2616,13 +2636,12 @@
|
|||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
||||
/**
|
||||
* TMC26X Stepper Driver options
|
||||
*
|
||||
* The TMC26XStepper library is required for this stepper driver.
|
||||
* https://github.com/trinamic/TMC26XStepper
|
||||
* @section tmc/tmc26x
|
||||
*/
|
||||
#if HAS_DRIVER(TMC26X)
|
||||
|
||||
|
|
@ -2760,8 +2779,6 @@
|
|||
|
||||
#endif // TMC26X
|
||||
|
||||
// @section tmc_smart
|
||||
|
||||
/**
|
||||
* To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode
|
||||
* connect your SPI pins to the hardware SPI interface on your board and define
|
||||
|
|
@ -2777,6 +2794,7 @@
|
|||
*
|
||||
* TMCStepper library is required to use TMC stepper drivers.
|
||||
* https://github.com/teemuatlut/TMCStepper
|
||||
* @section tmc/config
|
||||
*/
|
||||
#if HAS_TRINAMIC_CONFIG
|
||||
|
||||
|
|
@ -3000,6 +3018,8 @@
|
|||
//#define E7_HOLD_MULTIPLIER 0.5
|
||||
#endif
|
||||
|
||||
// @section tmc/spi
|
||||
|
||||
/**
|
||||
* Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here.
|
||||
* The default pins can be found in your board's pins file.
|
||||
|
|
@ -3037,6 +3057,8 @@
|
|||
//#define TMC_SW_MISO -1
|
||||
//#define TMC_SW_SCK -1
|
||||
|
||||
// @section tmc/serial
|
||||
|
||||
/**
|
||||
* Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses.
|
||||
* Set the address using jumpers on pins MS1 and MS2.
|
||||
|
|
@ -3072,6 +3094,8 @@
|
|||
//#define E6_SLAVE_ADDRESS 0
|
||||
//#define E7_SLAVE_ADDRESS 0
|
||||
|
||||
// @section tmc/smart
|
||||
|
||||
/**
|
||||
* Software enable
|
||||
*
|
||||
|
|
@ -3080,6 +3104,8 @@
|
|||
*/
|
||||
//#define SOFTWARE_DRIVER_ENABLE
|
||||
|
||||
// @section tmc/stealthchop
|
||||
|
||||
/**
|
||||
* TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
|
||||
* Use Trinamic's ultra quiet stepping mode.
|
||||
|
|
@ -3134,6 +3160,8 @@
|
|||
//#define CHOPPER_TIMING_E6 CHOPPER_TIMING_E
|
||||
//#define CHOPPER_TIMING_E7 CHOPPER_TIMING_E
|
||||
|
||||
// @section tmc/status
|
||||
|
||||
/**
|
||||
* Monitor Trinamic drivers
|
||||
* for error conditions like overtemperature and short to ground.
|
||||
|
|
@ -3153,6 +3181,8 @@
|
|||
#define STOP_ON_ERROR
|
||||
#endif
|
||||
|
||||
// @section tmc/hybrid
|
||||
|
||||
/**
|
||||
* TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
|
||||
* The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
|
||||
|
|
@ -3209,6 +3239,7 @@
|
|||
* homing and adds a guard period for endstop triggering.
|
||||
*
|
||||
* Comment *_STALL_SENSITIVITY to disable sensorless homing for that axis.
|
||||
* @section tmc/stallguard
|
||||
*/
|
||||
//#define SENSORLESS_HOMING // StallGuard capable drivers only
|
||||
|
||||
|
|
@ -3232,6 +3263,8 @@
|
|||
//#define IMPROVE_HOMING_RELIABILITY
|
||||
#endif
|
||||
|
||||
// @section tmc/config
|
||||
|
||||
/**
|
||||
* TMC Homing stepper phase.
|
||||
*
|
||||
|
|
@ -3312,7 +3345,7 @@
|
|||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
// @section photo
|
||||
|
||||
/**
|
||||
* Photo G-code
|
||||
|
|
@ -3355,6 +3388,8 @@
|
|||
#endif
|
||||
#endif
|
||||
|
||||
// @section cnc
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
|
|
@ -3559,6 +3594,8 @@
|
|||
#define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed
|
||||
#endif
|
||||
|
||||
// @section filament width
|
||||
|
||||
/**
|
||||
* Filament Width Sensor
|
||||
*
|
||||
|
|
@ -3592,6 +3629,8 @@
|
|||
//#define FILAMENT_LCD_DISPLAY
|
||||
#endif
|
||||
|
||||
// @section power
|
||||
|
||||
/**
|
||||
* Power Monitor
|
||||
* Monitor voltage (V) and/or current (A), and -when possible- power (W)
|
||||
|
|
@ -3615,6 +3654,8 @@
|
|||
#define POWER_MONITOR_VOLTAGE_OFFSET 0 // Offset (in volts) applied to the calculated voltage
|
||||
#endif
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
* Stepper Driver Anti-SNAFU Protection
|
||||
*
|
||||
|
|
@ -3624,6 +3665,8 @@
|
|||
*/
|
||||
//#define DISABLE_DRIVER_SAFE_POWER_PROTECT
|
||||
|
||||
// @section cnc
|
||||
|
||||
/**
|
||||
* CNC Coordinate Systems
|
||||
*
|
||||
|
|
@ -3640,6 +3683,8 @@
|
|||
*/
|
||||
//#define CNC_DRILLING_CYCLE
|
||||
|
||||
// @section reporting
|
||||
|
||||
/**
|
||||
* Auto-report fan speed with M123 S<seconds>
|
||||
* Requires fans with tachometer pins
|
||||
|
|
@ -3667,6 +3712,8 @@
|
|||
//#define M115_GEOMETRY_REPORT
|
||||
#endif
|
||||
|
||||
// @section security
|
||||
|
||||
/**
|
||||
* Expected Printer Check
|
||||
* Add the M16 G-code to compare a string to the MACHINE_NAME.
|
||||
|
|
@ -3674,6 +3721,8 @@
|
|||
*/
|
||||
//#define EXPECTED_PRINTER_CHECK
|
||||
|
||||
// @section volumetrics
|
||||
|
||||
/**
|
||||
* Disable all Volumetric extrusion options
|
||||
*/
|
||||
|
|
@ -3702,14 +3751,7 @@
|
|||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this option for a leaner build of Marlin that removes all
|
||||
* workspace offsets, simplifying coordinate transformations, leveling, etc.
|
||||
*
|
||||
* - M206 and M428 are disabled.
|
||||
* - G92 will revert to its behavior from Marlin 1.0.
|
||||
*/
|
||||
//#define NO_WORKSPACE_OFFSETS
|
||||
// @section reporting
|
||||
|
||||
// Extra options for the M114 "Current Position" report
|
||||
//#define M114_DETAIL // Use 'M114` for details to check planner calculations
|
||||
|
|
@ -3718,6 +3760,8 @@
|
|||
|
||||
//#define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
|
||||
|
||||
// @section gcode
|
||||
|
||||
/**
|
||||
* Spend 28 bytes of SRAM to optimize the G-code parser
|
||||
*/
|
||||
|
|
@ -3735,6 +3779,15 @@
|
|||
|
||||
//#define REPETIER_GCODE_M360 // Add commands originally from Repetier FW
|
||||
|
||||
/**
|
||||
* Enable this option for a leaner build of Marlin that removes all
|
||||
* workspace offsets, simplifying coordinate transformations, leveling, etc.
|
||||
*
|
||||
* - M206 and M428 are disabled.
|
||||
* - G92 will revert to its behavior from Marlin 1.0.
|
||||
*/
|
||||
//#define NO_WORKSPACE_OFFSETS
|
||||
|
||||
/**
|
||||
* CNC G-code options
|
||||
* Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
|
||||
|
|
@ -3751,6 +3804,8 @@
|
|||
#endif
|
||||
//#define G0_ANGULAR_FEEDRATE 2700 // (°/min)
|
||||
|
||||
// @section gcode
|
||||
|
||||
/**
|
||||
* Startup commands
|
||||
*
|
||||
|
|
@ -3775,6 +3830,8 @@
|
|||
* Up to 25 may be defined, but the actual number is LCD-dependent.
|
||||
*/
|
||||
|
||||
// @section custom main menu
|
||||
|
||||
// Custom Menu: Main Menu
|
||||
//#define CUSTOM_MENU_MAIN
|
||||
#if ENABLED(CUSTOM_MENU_MAIN)
|
||||
|
|
@ -3805,6 +3862,8 @@
|
|||
//#define MAIN_MENU_ITEM_5_CONFIRM
|
||||
#endif
|
||||
|
||||
// @section custom config menu
|
||||
|
||||
// Custom Menu: Configuration Menu
|
||||
//#define CUSTOM_MENU_CONFIG
|
||||
#if ENABLED(CUSTOM_MENU_CONFIG)
|
||||
|
|
@ -3835,6 +3894,8 @@
|
|||
//#define CONFIG_MENU_ITEM_5_CONFIRM
|
||||
#endif
|
||||
|
||||
// @section custom buttons
|
||||
|
||||
/**
|
||||
* User-defined buttons to run custom G-code.
|
||||
* Up to 25 may be defined.
|
||||
|
|
@ -3866,6 +3927,8 @@
|
|||
#endif
|
||||
#endif
|
||||
|
||||
// @section host
|
||||
|
||||
/**
|
||||
* Host Action Commands
|
||||
*
|
||||
|
|
@ -3891,6 +3954,8 @@
|
|||
//#define HOST_SHUTDOWN_MENU_ITEM // Add a menu item that tells the host to shut down
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Cancel Objects
|
||||
*
|
||||
|
|
@ -3912,6 +3977,7 @@
|
|||
* Alternative Supplier: https://reliabuild3d.com/
|
||||
*
|
||||
* Reliabuild encoders have been modified to improve reliability.
|
||||
* @section i2c encoders
|
||||
*/
|
||||
|
||||
//#define I2C_POSITION_ENCODERS
|
||||
|
|
@ -3983,6 +4049,7 @@
|
|||
|
||||
/**
|
||||
* Analog Joystick(s)
|
||||
* @section joystick
|
||||
*/
|
||||
//#define JOYSTICK
|
||||
#if ENABLED(JOYSTICK)
|
||||
|
|
@ -4007,6 +4074,7 @@
|
|||
* Modern replacement for the Prusa TMC_Z_CALIBRATION.
|
||||
* Adds capability to work with any adjustable current drivers.
|
||||
* Implemented as G34 because M915 is deprecated.
|
||||
* @section calibrate
|
||||
*/
|
||||
//#define MECHANICAL_GANTRY_CALIBRATION
|
||||
#if ENABLED(MECHANICAL_GANTRY_CALIBRATION)
|
||||
|
|
@ -4024,6 +4092,7 @@
|
|||
/**
|
||||
* Instant freeze / unfreeze functionality
|
||||
* Potentially useful for emergency stop that allows being resumed.
|
||||
* @section interface
|
||||
*/
|
||||
//#define FREEZE_FEATURE
|
||||
#if ENABLED(FREEZE_FEATURE)
|
||||
|
|
@ -4036,6 +4105,7 @@
|
|||
*
|
||||
* Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
|
||||
* Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
|
||||
* @section debug matrix
|
||||
*/
|
||||
//#define MAX7219_DEBUG
|
||||
#if ENABLED(MAX7219_DEBUG)
|
||||
|
|
@ -4074,6 +4144,7 @@
|
|||
* Support for Synchronized Z moves when used with NanoDLP. G0/G1 axis moves will
|
||||
* output a "Z_move_comp" string to enable synchronization with DLP projector exposure.
|
||||
* This feature allows you to use [[WaitForDoneMessage]] instead of M400 commands.
|
||||
* @section nanodlp
|
||||
*/
|
||||
//#define NANODLP_Z_SYNC
|
||||
#if ENABLED(NANODLP_Z_SYNC)
|
||||
|
|
@ -4082,6 +4153,7 @@
|
|||
|
||||
/**
|
||||
* Ethernet. Use M552 to enable and set the IP address.
|
||||
* @section network
|
||||
*/
|
||||
#if HAS_ETHERNET
|
||||
#define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xF0, 0x0D } // A MAC address unique to your network
|
||||
|
|
@ -4109,6 +4181,8 @@
|
|||
//#include "Configuration_Secure.h" // External file with WiFi SSID / Password
|
||||
#endif
|
||||
|
||||
// @section multi-material
|
||||
|
||||
/**
|
||||
* Průša Multi-Material Unit (MMU)
|
||||
* Enable in Configuration.h
|
||||
|
|
@ -4216,6 +4290,7 @@
|
|||
|
||||
/**
|
||||
* Advanced Print Counter settings
|
||||
* @section stats
|
||||
*/
|
||||
#if ENABLED(PRINTCOUNTER)
|
||||
#define SERVICE_WARNING_BUZZES 3
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue