3D-printing/Configurations
1
0
Fork 0
mirror of https://github.com/MarlinFirmware/Configurations.git synced 2025-07-14 02:07:57 -06:00
Code Issues Projects Releases Packages Wiki Activity Actions

📝 Add sections for schema

Browse source 
MarlinFirmware/Marlin#24528
This commit is contained in:
Scott Lahteine 2022-08-02 01:59:56 -05:00
parent c0e4a07015
commit 48ffab7d02
599 changed files with 40103 additions and 8744 deletions
Download patch file Download diff file Expand all files Collapse all files

80
config/examples/Mks/Robin_Lite3/Configuration.h
View file

@ -114,21 +114,24 @@
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
*/
#define BAUDRATE 250000
//#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate
/**
* Select a secondary serial port on the board to use for communication with the host.
* Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
* :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
*
* 1 : MKS Robin Lite3 AUX-1 and USB UART1 (PA9-TX, PA10-RX)
* 3 : MKS Robin Pro USB UART3 (PB10-TX, PB11-RX)
* 1 : MKS RUMBA32 AUX-1 UART1 (PA9-TX, PA10-RX)
* 0 : MKS SBASE AUX-1 UART0 (P0.2-TXD0, P0.3-RXD0)
* 0 : MKS SGEN AUX-1 UART0 (P0.2-TXD0, P0.3-RXD0)
* 0 : MKS SGEN_L AUX-1 UART0 (P0.2-TXD0, P0.3-RXD0)
* 3 : MKS Robin Nano USB UART3 (PB10-TX, PB11-RX)
*/
//#define SERIAL_PORT_2 1 // MKS Robin Lite3 AUX-1 and USB UART1 (PA9-TX, PA10-RX)
//#define SERIAL_PORT_2 3 // MKS Robin Pro USB UART3 (PB10-TX, PB11-RX)
//#define SERIAL_PORT_2 1 // MKS RUMBA32 AUX-1 UART1 (PA9-TX, PA10-RX)
//#define SERIAL_PORT_2 0 // MKS SBASE AUX-1 UART0 (P0.2-TXD0, P0.3-RXD0)
//#define SERIAL_PORT_2 0 // MKS SGEN AUX-1 UART0 (P0.2-TXD0, P0.3-RXD0)
//#define SERIAL_PORT_2 0 // MKS SGEN_L AUX-1 UART0 (P0.2-TXD0, P0.3-RXD0)
//#define SERIAL_PORT_2 3 // MKS Robin Nano USB UART3 (PB10-TX, PB11-RX)
//#define BAUDRATE_2 250000 // Enable to override BAUDRATE
//#define SERIAL_PORT_2 // Choose from the list above
//#define BAUDRATE_2 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
/**
* Select a third serial port on the board to use for communication with the host.
@ -136,7 +139,7 @@
* :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
*/
//#define SERIAL_PORT_3 1
//#define BAUDRATE_3 250000 // Enable to override BAUDRATE
//#define BAUDRATE_3 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
// Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH
@ -395,7 +398,7 @@
//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
// @section machine
// @section psu control
/**
* Power Supply Control
@ -631,6 +634,8 @@
//============================= PID Settings ================================
//===========================================================================
// @section hotend temp
// Enable PIDTEMP for PID control or MPCTEMP for Predictive Model.
// temperature control. Disable both for bang-bang heating.
#define PIDTEMP // See the PID Tuning Guide at https://reprap.org/wiki/PID_Tuning
@ -641,7 +646,8 @@
#define PID_K1 0.95 // Smoothing factor within any PID loop
#if ENABLED(PIDTEMP)
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
// Set/get with G-code: M301 E[extruder number, 0-2]
#if ENABLED(PID_PARAMS_PER_HOTEND)
@ -663,6 +669,7 @@
* Use a physical model of the hotend to control temperature. When configured correctly
* this gives better responsiveness and stability than PID and it also removes the need
* for PID_EXTRUSION_SCALING and PID_FAN_SCALING. Use M306 T to autotune the model.
* @section mpctemp
*/
#if ENABLED(MPCTEMP)
//#define MPC_EDIT_MENU // Add MPC editing to the "Advanced Settings" menu. (~1300 bytes of flash)
@ -730,7 +737,7 @@
#if ENABLED(PIDTEMPBED)
//#define MIN_BED_POWER 0
//#define PID_BED_DEBUG // Sends debug data to the serial port.
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
@ -758,6 +765,7 @@
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
* heater. If your configuration is significantly different than this and you don't understand
* the issues involved, don't use chamber PID until someone else verifies that your hardware works.
* @section chamber temp
*/
//#define PIDTEMPCHAMBER
//#define CHAMBER_LIMIT_SWITCHING
@ -772,7 +780,7 @@
#if ENABLED(PIDTEMPCHAMBER)
#define MIN_CHAMBER_POWER 0
//#define PID_CHAMBER_DEBUG // Sends debug data to the serial port.
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
// and placed inside the small Creality printer enclosure tent.
@ -786,7 +794,6 @@
#endif // PIDTEMPCHAMBER
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
//#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
@ -796,7 +803,7 @@
//#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
#endif
// @section extruder
// @section safety
/**
* Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
@ -864,6 +871,8 @@
#define POLAR_SEGMENTS_PER_SECOND 5
#endif
// @section delta
// Enable for DELTA kinematics and configure below
//#define DELTA
#if ENABLED(DELTA)
@ -923,6 +932,8 @@
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
#endif
// @section scara
/**
* MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
* Implemented and slightly reworked by JCERNY in June, 2014.
@ -966,6 +977,8 @@
#endif
// @section tpara
// Enable for TPARA kinematics and configure below
//#define AXEL_TPARA
#if ENABLED(AXEL_TPARA)
@ -992,6 +1005,8 @@
#define PSI_HOMING_OFFSET 0
#endif
// @section machine
// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
//#define ARTICULATED_ROBOT_ARM
@ -1003,7 +1018,7 @@
//============================== Endstop Settings ===========================
//===========================================================================
// @section homing
// @section endstops
// Specify here all the endstop connectors that are connected to any endstop or probe.
// Almost all printers will be using one per axis. Probes will use one or more of the
@ -1673,7 +1688,7 @@
//#define V_HOME_DIR -1
//#define W_HOME_DIR -1
// @section machine
// @section geometry
// The size of the printable area
#define X_BED_SIZE 200
@ -2133,7 +2148,7 @@
//============================= Additional Features ===========================
//=============================================================================
// @section extras
// @section eeprom
/**
* EEPROM
@ -2153,6 +2168,8 @@
//#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
#endif
// @section host
//
// Host Keepalive
//
@ -2163,6 +2180,8 @@
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
// @section units
//
// G20/G21 Inch mode support
//
@ -2190,6 +2209,8 @@
#define PREHEAT_2_TEMP_CHAMBER 35
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
// @section motion
/**
* Nozzle Park
*
@ -2288,6 +2309,8 @@
#endif
// @section host
/**
* Print Job Timer
*
@ -2314,6 +2337,8 @@
*/
#define PRINTJOB_TIMER_AUTOSTART
// @section stats
/**
* Print Counter
*
@ -2331,6 +2356,8 @@
#define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print
#endif
// @section security
/**
* Password
*
@ -2366,7 +2393,7 @@
//============================= LCD and SD support ============================
//=============================================================================
// @section lcd
// @section interface
/**
* LCD LANGUAGE
@ -2522,6 +2549,7 @@
//======================== LCD / Controller Selection =========================
//======================== (Character-based LCDs) =========================
//=============================================================================
// @section lcd
//
// RepRapDiscount Smart Controller.
@ -3167,7 +3195,7 @@
//=============================== Extra Features ==============================
//=============================================================================
// @section extras
// @section fans
// Set number of user-controlled fans. Disable to use all board-defined fans.
// :[1,2,3,4,5,6,7,8]
@ -3191,14 +3219,18 @@
// duty cycle is attained.
//#define SOFT_PWM_DITHER
// @section extras
// Support for the BariCUDA Paste Extruder
//#define BARICUDA
// @section lights
// Temperature status LEDs that display the hotend and bed temperature.
// If all hotends, bed temperature, and target temperature are under 54C
// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
//#define TEMP_STAT_LEDS
// Support for the BariCUDA Paste Extruder
//#define BARICUDA
// Support for BlinkM/CyzRgb
//#define BLINKM
@ -3284,6 +3316,8 @@
#define PRINTER_EVENT_LEDS
#endif
// @section servos
/**
* Number of servos
*