mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2025-08-07 14:04:19 -06:00
📝 Update PID, other comments
This commit is contained in:
Scott Lahteine
parent
2ba199d117
commit
3baff79239
765 changed files with 6142 additions and 5373 deletions
|
|
@ -721,8 +721,10 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
// Anycubic Kossel - run 'M106 S255' & 'M303 E0 C10 S200'
|
||||
|
|
@ -747,6 +749,7 @@
|
|||
* Use a physical model of the hotend to control temperature. When configured correctly this gives
|
||||
* better responsiveness and stability than PID and removes the need for PID_EXTRUSION_SCALING
|
||||
* and PID_FAN_SCALING. Enable MPC_AUTOTUNE and use M306 T to autotune the model.
|
||||
* @section mpc temp
|
||||
*/
|
||||
#if ENABLED(MPCTEMP)
|
||||
#define MPC_AUTOTUNE // Include a method to do MPC auto-tuning (~6.3K bytes of flash)
|
||||
|
|
@ -821,7 +824,9 @@
|
|||
#define PIDTEMPBED
|
||||
#endif
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Anycubic Kossel
|
||||
// this is for the aluminium bed with a BuildTak-like sticker on it
|
||||
|
|
@ -837,8 +842,6 @@
|
|||
#define DEFAULT_bedKd 482.59
|
||||
#endif
|
||||
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#else
|
||||
//#define BED_LIMIT_SWITCHING // Keep the bed temperature within BED_HYSTERESIS of the target
|
||||
|
|
@ -912,12 +915,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
@ -929,7 +932,6 @@
|
|||
// @section pid temp
|
||||
|
||||
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
|
||||
//#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
|
|
@ -1059,26 +1061,18 @@
|
|||
#define PROBE_MANUALLY_STEP 0.05 // (mm)
|
||||
#endif
|
||||
|
||||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
#if ENABLED(ANYCUBIC_KOSSEL_PLUS)
|
||||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
#define PRINTABLE_RADIUS 120.0 // (mm)
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 267 // (mm)
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 186 // (mm)
|
||||
// Horizontal offset of the universal joints on the end effector.
|
||||
#define DELTA_EFFECTOR_OFFSET 31 // (mm)
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 20.6 // (mm)
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) // (mm) Get this value from G33 auto calibrate
|
||||
#define PRINTABLE_RADIUS 120.0 // (mm)
|
||||
#else
|
||||
#define PRINTABLE_RADIUS 90.0 // (mm)
|
||||
#endif
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#if ENABLED(ANYCUBIC_KOSSEL_PLUS)
|
||||
#define DELTA_DIAGONAL_ROD 250.0 // (mm)
|
||||
#else
|
||||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
#define PRINTABLE_RADIUS 90.0 // (mm)
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 218.0 // (mm)
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 97.0 // (mm) Get this value from G33 auto calibrate
|
||||
#endif
|
||||
|
||||
// Distance between bed and nozzle Z home position
|
||||
|
|
@ -1086,6 +1080,16 @@
|
|||
|
||||
#define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // (mm) Get these values from G33 auto calibrate
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#if ENABLED(ANYCUBIC_KOSSEL_PLUS)
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 186 // (mm) Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_EFFECTOR_OFFSET 31 // (mm) Horizontal offset of the universal joints on the end effector.
|
||||
#define DELTA_CARRIAGE_OFFSET 20.6 // (mm) Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) // (mm) Get this value from G33 auto calibrate
|
||||
#else
|
||||
#define DELTA_RADIUS 97.0 // (mm) Get this value from G33 auto calibrate
|
||||
#endif
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
|
|
@ -1094,7 +1098,6 @@
|
|||
// Delta radius and diagonal rod adjustments
|
||||
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } // (mm)
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } // (mm)
|
||||
|
||||
#endif
|
||||
|
||||
// @section scara
|
||||
|
|
@ -1346,14 +1349,15 @@
|
|||
* Override with M92 (when enabled below)
|
||||
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
|
||||
*/
|
||||
// variables to calculate steps
|
||||
|
||||
// Variables to calculate steps
|
||||
#define XYZ_FULL_STEPS_PER_ROTATION 200
|
||||
#define XYZ_MICROSTEPS 16
|
||||
#define XYZ_BELT_PITCH 2
|
||||
#define XYZ_PULLEY_TEETH 20
|
||||
|
||||
#define DEFAULT_XYZ_STEPS_PER_UNIT ((XYZ_FULL_STEPS_PER_ROTATION) * (XYZ_MICROSTEPS) / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH)) // 80
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { DEFAULT_XYZ_STEPS_PER_UNIT, DEFAULT_XYZ_STEPS_PER_UNIT, DEFAULT_XYZ_STEPS_PER_UNIT, 96 } // default steps per unit for Kossel (GT2, 20 tooth)
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { DEFAULT_XYZ_STEPS_PER_UNIT, DEFAULT_XYZ_STEPS_PER_UNIT, DEFAULT_XYZ_STEPS_PER_UNIT, 96 } // default steps per unit for Kossel (GT2, 20 tooth)
|
||||
|
||||
/**
|
||||
* Enable support for M92. Disable to save at least ~530 bytes of flash.
|
||||
|
|
@ -1509,6 +1513,12 @@
|
|||
#define FIX_MOUNTED_PROBE
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Use the nozzle as the probe, as with a conductive
|
||||
* nozzle system or a piezo-electric smart effector.
|
||||
*/
|
||||
//#define NOZZLE_AS_PROBE
|
||||
|
||||
/**
|
||||
* Z Servo Probe, such as an endstop switch on a rotating arm.
|
||||
*/
|
||||
|
|
@ -2439,7 +2449,6 @@
|
|||
//#define Z_SAFE_HOMING_POINT_ABSOLUTE // Ignore home offsets (M206) for Z homing position
|
||||
#endif
|
||||
|
||||
// Homing speeds (linear=mm/min, rotational=°/min)
|
||||
// Homing speeds (linear=mm/min, rotational=°/min)
|
||||
#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (50*60) }
|
||||
|
||||
|
|
|
|||
|
|
@ -689,8 +689,7 @@
|
|||
* Multiple extruders can be assigned to the same pin in which case
|
||||
* the fan will turn on when any selected extruder is above the threshold.
|
||||
*/
|
||||
#define E0_AUTO_FAN_PIN 44 // turn off extruder fan when it's temperature is above 50°C
|
||||
|
||||
#define E0_AUTO_FAN_PIN 44 // Turn off extruder fan when its temperature is above 50°C
|
||||
#define E1_AUTO_FAN_PIN -1
|
||||
#define E2_AUTO_FAN_PIN -1
|
||||
#define E3_AUTO_FAN_PIN -1
|
||||
|
|
@ -1343,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -721,8 +721,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -838,7 +839,7 @@
|
|||
#define DEFAULT_bedKd 482.59
|
||||
#endif
|
||||
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#else
|
||||
|
|
@ -913,12 +914,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -884,12 +886,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1344,20 +1344,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -700,8 +700,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Overlord Pro heater into 5.5mm aluminium bed, update using M303
|
||||
#define DEFAULT_bedKp 253.16
|
||||
|
|
@ -882,12 +884,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -707,8 +707,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -808,8 +809,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Overlord Pro heater into 5.5mm aluminium bed, update using M303
|
||||
#define DEFAULT_bedKp 253.16
|
||||
|
|
@ -889,12 +891,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
|
||||
#define DEFAULT_bedKp 17.83
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// flsun Q5 via M303 E-1 C8 S60
|
||||
#define DEFAULT_bedKp 58.98
|
||||
|
|
@ -882,12 +884,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// FLSUN QQ-S stock 1.6mm aluminium heater with 4mm lattice glass
|
||||
#define DEFAULT_bedKp 325.10
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// FLSUN QQS-Pro 1.6mm aluminium heater with 4mm lattice glass
|
||||
#define DEFAULT_bedKp 82.98
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1343,20 +1343,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// D-force
|
||||
#define DEFAULT_bedKp 22.97
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// D-force
|
||||
#define DEFAULT_bedKp 22.97
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// D-force
|
||||
#define DEFAULT_bedKp 22.97
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -706,8 +706,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -807,8 +808,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// HatchBox Alpha
|
||||
#define DEFAULT_bedKp 72.11
|
||||
|
|
@ -888,12 +890,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -884,12 +886,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -802,8 +803,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 220V TEVO Little Monster PID Autotune
|
||||
#define DEFAULT_bedKp 60.40
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -712,8 +712,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -813,8 +814,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -895,12 +897,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1343,20 +1343,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -801,8 +802,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -883,12 +885,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -705,8 +705,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -806,8 +807,9 @@
|
|||
#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Kossel Pro heated bed plate with borosilicate glass
|
||||
// from pidautotune (M303 E-1 S60 C8)
|
||||
|
|
@ -888,12 +890,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
|
|
@ -701,8 +701,9 @@
|
|||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define MIN_POWER 0
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
|
||||
//#define MIN_POWER 0 // Min power to improve PID stability (0..PID_MAX).
|
||||
// Get the power from the temperature report ('M105' => @:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with G-code: M301 E[extruder number, 0-2]
|
||||
|
||||
|
|
@ -807,8 +808,9 @@
|
|||
//#define PIDTEMPBED
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port.
|
||||
//#define MIN_BED_POWER 0 // Min power to improve PID stability (0..MAX_BED_POWER).
|
||||
// Get the power from the temperature report ('M105' => B@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_BED_DEBUG // Print Bed PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
|
@ -889,12 +891,12 @@
|
|||
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPCHAMBER)
|
||||
#define MIN_CHAMBER_POWER 0
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port.
|
||||
#define MIN_CHAMBER_POWER 0 // Min power to improve PID stability. (0..MAX_CHAMBER_POWER)
|
||||
// Get the power from the temperature report ('M105' => C@:nnn) and try P*2-20 to P*2-10.
|
||||
//#define PID_CHAMBER_DEBUG // Print Chamber PID debug data to the serial port. Use 'M303 D' to enable/disable.
|
||||
|
||||
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
|
||||
// and placed inside the small Creality printer enclosure tent.
|
||||
//
|
||||
#define DEFAULT_chamberKp 37.04
|
||||
#define DEFAULT_chamberKi 1.40
|
||||
#define DEFAULT_chamberKd 655.17
|
||||
|
|
|
|||
|
|
@ -1342,20 +1342,20 @@
|
|||
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
|
||||
//#define CALIBRATION_SCRIPT_POST "M500\nM117 Calibration data saved"
|
||||
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/min
|
||||
#define CALIBRATION_FEEDRATE_SLOW 60 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_FAST 1200 // (mm/min)
|
||||
#define CALIBRATION_FEEDRATE_TRAVEL 3000 // (mm/min)
|
||||
|
||||
// The following parameters refer to the conical section of the nozzle tip.
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // (mm)
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // (mm)
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
|
||||
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // (mm)
|
||||
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // (mm)
|
||||
|
||||
// Comment out any sides which are unreachable by the probe. For best
|
||||
// auto-calibration results, all sides must be reachable.
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue