📝 Spellcheck

config/default/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/default/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -1112,7 +1112,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -3907,7 +3907,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -1121,7 +1121,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -1166,7 +1166,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -3922,7 +3922,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Alfawise/U20/Configuration.h

@@ -1168,7 +1168,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Alfawise/U20/Configuration_adv.h

@@ -3912,7 +3912,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AliExpress/CL-260/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -3913,7 +3913,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/A2/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/A2/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/A2plus/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/A2plus/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/A6/Configuration.h

@@ -1127,7 +1127,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/A6/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/A8/Configuration.h

@@ -1113,7 +1113,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/A8/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/A8plus/Configuration.h

@@ -1112,7 +1112,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/A8plus/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/A9/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/A9/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/E10/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/E10/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/E16/BTT SKR 1.3/Configuration.h

@@ -1112,7 +1112,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/E16/Stock/Configuration.h

@@ -1112,7 +1112,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/E16/Stock/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET4+/Configuration.h

@@ -1116,7 +1116,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET4+/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET4-Pro/Configuration.h

@@ -1116,7 +1116,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET4-Pro/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET4/Configuration.h

@@ -1116,7 +1116,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET4/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET4X/Configuration.h

@@ -1116,7 +1116,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET4X/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET5-Pro/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET5-Pro/Configuration_adv.h

@@ -3908,7 +3908,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET5/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET5/Configuration_adv.h

@@ -3908,7 +3908,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Anet/ET5X/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Anet/ET5X/Configuration_adv.h

@@ -3908,7 +3908,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AnyCubic/Chiron/Configuration.h

@@ -1113,7 +1113,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AnyCubic/Chiron/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h

@@ -1112,7 +1112,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h

@@ -1112,7 +1112,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AnyCubic/i3 Mega/Configuration.h

@@ -1140,7 +1140,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AnyCubic/i3 Mega/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/AnyCubic/i3/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/ArmEd/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/ArmEd/Configuration_adv.h

@@ -3915,7 +3915,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Artillery/Genius/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Artillery/Genius/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Artillery/Sidewinder X1/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Artillery/Sidewinder X1/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h

@@ -1126,7 +1126,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Azteeg/X5GT/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BIBO/TouchX/default/Configuration.h

@@ -1066,7 +1066,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -3904,7 +3904,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BIQU/B1-BLTouch/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BIQU/B1-BLTouch/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BIQU/B1/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BIQU/B1/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BQ/Hephestos/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BQ/Hephestos_2/Configuration.h

@@ -1124,7 +1124,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -3919,7 +3919,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/BQ/WITBOX/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/CTC/A13/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/CTC/A13/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Cartesio/Configuration.h

@@ -1126,7 +1126,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Cartesio/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Copymaster3D/300/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Copymaster3D/400/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Copymaster3D/500/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -1119,7 +1119,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h

@@ -1119,7 +1119,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h

@@ -3911,7 +3911,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h

@@ -1110,7 +1110,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h

@@ -3908,7 +3908,7 @@
    */
   #define I2CPE_MIN_UPD_TIME_MS     4                       // (ms) Minimum time between encoder checks.
 
-  // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+  // Use a rolling average to identify persistent errors that indicate skips, as opposed to vibration and noise.
   #define I2CPE_ERR_ROLLING_AVERAGE
 
 #endif // I2C_POSITION_ENCODERS

config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h

@@ -1111,7 +1111,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensivity.
+// When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin