✨ EVENT_GCODE_AFTER_MPC_TUNE

MarlinFirmware/Marlin#27865

Co-Authored-By: Vovodroid <vovodroid@users.noreply.github.com>

config/default/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -774,6 +774,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/3DMatik/XL/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -831,6 +831,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Alfawise/U20/Configuration.h

@@ -831,6 +831,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AliExpress/CL-260/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/A2/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/A2plus/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/A6/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/A8/Configuration.h

@@ -775,6 +775,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/A8plus/Configuration.h

@@ -775,6 +775,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/A9/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/E10/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/E16/BTT SKR 1.3/Configuration.h

@@ -774,6 +774,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/E16/Stock/Configuration.h

@@ -774,6 +774,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET4+/Configuration.h

@@ -778,6 +778,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET4-Pro/Configuration.h

@@ -778,6 +778,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET4/Configuration.h

@@ -778,6 +778,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET4X/Configuration.h

@@ -778,6 +778,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET5-Pro/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET5/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Anet/ET5X/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/Chiron/Configuration.h

@@ -777,6 +777,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/Vyper/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration.h

@@ -812,6 +812,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration.h

@@ -780,6 +780,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/AnyCubic/i3/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/ArmEd/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Genius Pro/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Genius/BLTouch/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Genius/V1/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Hornet/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h

@@ -783,6 +783,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Sidewinder X1/V1/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Artillery/Sidewinder X2/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Azteeg/X5GT/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIBO/TouchX/default - BLTouch/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIBO/TouchX/default/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIQU/B1 SE Plus/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIQU/B1 SE/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIQU/B1/Configuration.h

@@ -780,6 +780,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIQU/BX/Configuration.h

@@ -793,6 +793,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIQU/Hurakan/Configuration.h

@@ -776,6 +776,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BIQU/Thunder Standard/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BQ/Hephestos/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BQ/Hephestos_2/Configuration.h

@@ -786,6 +786,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/BQ/WITBOX/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/CNC/miniRambo/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/CTC/A13/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/CTC/Bizer/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Cartesio/Configuration.h

@@ -784,6 +784,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Copymaster3D/300/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Copymaster3D/400/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Copymaster3D/500/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 Max/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -782,6 +782,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -782,6 +782,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h

@@ -782,6 +782,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 V2/Configuration.h

@@ -780,6 +780,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration.h

@@ -780,6 +780,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10 V3/Stock/Configuration.h

@@ -780,6 +780,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10/CrealityV1/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S Pro/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-10S/CrealityV1/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-20/Stock/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-30 PrintMill/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-6 SE/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/CR-8/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-2/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-3 Max Neo/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-3 Max/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-3 Neo/Configuration.h

@@ -773,6 +773,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================

config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h

@@ -772,6 +772,7 @@
 
   #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height.
   #define MPC_TUNING_END_Z 10.0f                      // (mm) M306 Autotuning final Z position.
+  //#define EVENT_GCODE_AFTER_MPC_TUNE "M84"          // G-code to execute after MPC tune finished and Z raised.
 #endif
 
 //===========================================================================