mirror of
https://github.com/MarlinFirmware/Configurations.git
synced 2026-01-07 07:07:43 -07:00
Examples Customizations
This commit is contained in:
Scott Lahteine
parent
20282ab669
commit
30dfbb2edc
287 changed files with 12177 additions and 11874 deletions
|
|
@ -89,7 +89,7 @@
|
|||
#define SHOW_BOOTSCREEN
|
||||
|
||||
// Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
//#define SHOW_CUSTOM_BOOTSCREEN
|
||||
#define SHOW_CUSTOM_BOOTSCREEN
|
||||
|
||||
// Show the bitmap in Marlin/_Statusscreen.h on the status screen.
|
||||
//#define CUSTOM_STATUS_SCREEN_IMAGE
|
||||
|
|
@ -130,11 +130,16 @@
|
|||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
//#define MOTHERBOARD BOARD_RAMPS_14_EEF
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB // gMax users please note: This is a Roxy modification. I print on glass and
|
||||
// I use Marlin to control the bed's temperature. So, if you have a single nozzle
|
||||
// machine, this will work fine for you. You just set the
|
||||
// #define TEMP_SENSOR_BED 75 to 0 down below so Marlin doesn't mess with the bed
|
||||
// temp.
|
||||
#endif
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
#define CUSTOM_MACHINE_NAME "gMax"
|
||||
|
||||
// Printer's unique ID, used by some programs to differentiate between machines.
|
||||
// Choose your own or use a service like http://www.uuidgenerator.net/version4
|
||||
|
|
@ -147,7 +152,7 @@
|
|||
#define EXTRUDERS 1
|
||||
|
||||
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
|
||||
|
||||
// For Cyclops or any "multi-extruder" that shares a single nozzle.
|
||||
//#define SINGLENOZZLE
|
||||
|
|
@ -406,7 +411,7 @@
|
|||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
|
|
@ -414,8 +419,10 @@
|
|||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_6 0
|
||||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_BED 75 // gMax-1.5+ users please note: This is a Roxy modification to the printer. I want
|
||||
// to print on glass. And I'm using a 400mm x 400mm silicon heat pad powered through
|
||||
// a Fortek SSR to do it. If you are using an unaltered gCreate machine, this needs
|
||||
// to be set to 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
|
|
@ -427,9 +434,9 @@
|
|||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
#define TEMP_RESIDENCY_TIME 16 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 5 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 12 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
|
|
@ -450,15 +457,15 @@
|
|||
// Above this temperature the heater will be switched off.
|
||||
// This can protect components from overheating, but NOT from shorts and failures.
|
||||
// (Use MINTEMP for thermistor short/failure protection.)
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
#define HEATER_4_MAXTEMP 275
|
||||
#define HEATER_5_MAXTEMP 275
|
||||
#define HEATER_6_MAXTEMP 275
|
||||
#define HEATER_7_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
#define HEATER_0_MAXTEMP 245
|
||||
#define HEATER_1_MAXTEMP 245
|
||||
#define HEATER_2_MAXTEMP 245
|
||||
#define HEATER_3_MAXTEMP 245
|
||||
#define HEATER_4_MAXTEMP 245
|
||||
#define HEATER_5_MAXTEMP 245
|
||||
#define HEATER_6_MAXTEMP 245
|
||||
#define HEATER_7_MAXTEMP 245
|
||||
#define BED_MAXTEMP 115
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
|
|
@ -483,10 +490,15 @@
|
|||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
|
||||
// gMax J-Head
|
||||
#define DEFAULT_Kp 15.35
|
||||
#define DEFAULT_Ki 0.85
|
||||
#define DEFAULT_Kd 69.45
|
||||
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
//#define DEFAULT_Kp 22.2
|
||||
//#define DEFAULT_Ki 1.08
|
||||
//#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
//#define DEFAULT_Kp 7.0
|
||||
|
|
@ -517,7 +529,7 @@
|
|||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
|
|
@ -535,9 +547,9 @@
|
|||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
#define DEFAULT_bedKp 135.44
|
||||
#define DEFAULT_bedKi 24.60
|
||||
#define DEFAULT_bedKd 186.40
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
|
|
@ -613,14 +625,14 @@
|
|||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||||
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
|
||||
#define USE_XMIN_PLUG
|
||||
#define USE_YMIN_PLUG
|
||||
//#define USE_YMIN_PLUG
|
||||
#define USE_ZMIN_PLUG
|
||||
//#define USE_XMAX_PLUG
|
||||
//#define USE_YMAX_PLUG
|
||||
#define USE_YMAX_PLUG
|
||||
//#define USE_ZMAX_PLUG
|
||||
|
||||
// Enable pullup for all endstops to prevent a floating state
|
||||
#define ENDSTOPPULLUPS
|
||||
//#define ENDSTOPPULLUPS
|
||||
#if DISABLED(ENDSTOPPULLUPS)
|
||||
// Disable ENDSTOPPULLUPS to set pullups individually
|
||||
//#define ENDSTOPPULLUP_XMAX
|
||||
|
|
@ -646,11 +658,11 @@
|
|||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
|
||||
|
||||
|
|
@ -730,14 +742,14 @@
|
|||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 96 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 500, 500, 25, 25 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
|
|
@ -750,7 +762,7 @@
|
|||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 800, 800, 700, 10000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
|
|
@ -765,9 +777,9 @@
|
|||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 400 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
* Default Jerk limits (mm/s)
|
||||
|
|
@ -779,9 +791,9 @@
|
|||
*/
|
||||
//#define CLASSIC_JERK
|
||||
#if ENABLED(CLASSIC_JERK)
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
#define DEFAULT_XJERK 8.5
|
||||
#define DEFAULT_YJERK 8.5
|
||||
#define DEFAULT_ZJERK 0.7
|
||||
|
||||
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
|
||||
#if ENABLED(LIMITED_JERK_EDITING)
|
||||
|
|
@ -789,7 +801,7 @@
|
|||
#endif
|
||||
#endif
|
||||
|
||||
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance
|
||||
#define DEFAULT_EJERK 4.0 // May be used by Linear Advance
|
||||
|
||||
/**
|
||||
* Junction Deviation Factor
|
||||
|
|
@ -799,7 +811,7 @@
|
|||
* http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html
|
||||
*/
|
||||
#if DISABLED(CLASSIC_JERK)
|
||||
#define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge
|
||||
#define JUNCTION_DEVIATION_MM 0.058 // (mm) Distance from real junction edge
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
@ -882,7 +894,7 @@
|
|||
/**
|
||||
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
|
||||
*/
|
||||
//#define BLTOUCH
|
||||
#define BLTOUCH
|
||||
|
||||
/**
|
||||
* Touch-MI Probe by hotends.fr
|
||||
|
|
@ -915,13 +927,6 @@
|
|||
#define Z_PROBE_RETRACT_X X_MAX_POS
|
||||
#endif
|
||||
|
||||
// Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
|
||||
// When the pin is defined you can use M672 to set/reset the probe sensivity.
|
||||
//#define DUET_SMART_EFFECTOR
|
||||
#if ENABLED(DUET_SMART_EFFECTOR)
|
||||
#define SMART_EFFECTOR_MOD_PIN -1 // Connect a GPIO pin to the Smart Effector MOD pin
|
||||
#endif
|
||||
|
||||
//
|
||||
// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
|
||||
//
|
||||
|
|
@ -946,14 +951,14 @@
|
|||
*
|
||||
* Specify a Probe position as { X, Y, Z }
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -17, -10, -0.25 }
|
||||
|
||||
// Most probes should stay away from the edges of the bed, but
|
||||
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
|
||||
#define MIN_PROBE_EDGE 10
|
||||
#define MIN_PROBE_EDGE 45
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 8000
|
||||
#define XY_PROBE_SPEED 7500
|
||||
|
||||
// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
|
||||
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
|
||||
|
|
@ -987,10 +992,10 @@
|
|||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 6 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
//#define Z_AFTER_PROBING 6 // Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
|
|
@ -999,7 +1004,7 @@
|
|||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// Before deploy/stow pause for user confirmation
|
||||
//#define PAUSE_BEFORE_DEPLOY_STOW
|
||||
|
|
@ -1046,9 +1051,9 @@
|
|||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
|
||||
// @section extruder
|
||||
|
||||
|
|
@ -1068,20 +1073,21 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Y_HOME_DIR 1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
// @section machine
|
||||
|
||||
// The size of the print bed
|
||||
#define X_BED_SIZE 200
|
||||
#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 420 // These numbers are not accurate for an unaltered gMax 1.5+ printer. My print bed
|
||||
#define Y_BED_SIZE 420 // is inset a noticable amount from the edge of the bed. Combined with the inset,
|
||||
// the nozzle can reach all cordinates of the mesh.
|
||||
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
|
|
@ -1089,7 +1095,7 @@
|
|||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 500
|
||||
|
||||
/**
|
||||
* Software Endstops
|
||||
|
|
@ -1101,7 +1107,7 @@
|
|||
*/
|
||||
|
||||
// Min software endstops constrain movement within minimum coordinate bounds
|
||||
#define MIN_SOFTWARE_ENDSTOPS
|
||||
//#define MIN_SOFTWARE_ENDSTOPS
|
||||
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
|
||||
#define MIN_SOFTWARE_ENDSTOP_X
|
||||
#define MIN_SOFTWARE_ENDSTOP_Y
|
||||
|
|
@ -1128,7 +1134,7 @@
|
|||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
|
||||
|
|
@ -1193,21 +1199,21 @@
|
|||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Normally G28 leaves leveling disabled on completion. Enable
|
||||
* this option to have G28 restore the prior leveling state.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
* Enable detailed logging of G28, G29, M48, etc.
|
||||
* Turn on with the command 'M111 S32'.
|
||||
* NOTE: Requires a lot of PROGMEM!
|
||||
*/
|
||||
//#define DEBUG_LEVELING_FEATURE
|
||||
#define DEBUG_LEVELING_FEATURE
|
||||
|
||||
#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
|
||||
// Gradually reduce leveling correction until a set height is reached,
|
||||
|
|
@ -1224,10 +1230,10 @@
|
|||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.5 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.3 // (mm) Default layer height for the G26 Mesh Validation Tool.
|
||||
#define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
|
||||
#define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
|
||||
#define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
|
||||
|
|
@ -1268,9 +1274,9 @@
|
|||
//========================= Unified Bed Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
|
||||
|
||||
#define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
|
||||
#define MESH_INSET 45 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
|
|
@ -1294,6 +1300,19 @@
|
|||
|
||||
#endif // BED_LEVELING
|
||||
|
||||
/**
|
||||
* Points to probe for all 3-point Leveling procedures.
|
||||
* Override if the automatically selected points are inadequate.
|
||||
*/
|
||||
#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
|
||||
#define PROBE_PT_1_X 53
|
||||
#define PROBE_PT_1_Y 323
|
||||
#define PROBE_PT_2_X 53
|
||||
#define PROBE_PT_2_Y 63
|
||||
#define PROBE_PT_3_X 348
|
||||
#define PROBE_PT_3_Y 211
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Add a bed leveling sub-menu for ABL or MBL.
|
||||
* Include a guided procedure if manual probing is enabled.
|
||||
|
|
@ -1343,16 +1362,16 @@
|
|||
// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
|
||||
// - Prevent Z homing when the Z probe is outside bed area.
|
||||
//
|
||||
//#define Z_SAFE_HOMING
|
||||
#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2 - 8) // X point for Z homing when homing all axes (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2 - 4) // Y point for Z homing when homing all axes (G28).
|
||||
#endif
|
||||
|
||||
// Homing speeds (mm/m)
|
||||
#define HOMING_FEEDRATE_XY (50*60)
|
||||
#define HOMING_FEEDRATE_Z (4*60)
|
||||
#define HOMING_FEEDRATE_XY (60*60)
|
||||
#define HOMING_FEEDRATE_Z (14*60)
|
||||
|
||||
// Validate that endstops are triggered on homing moves
|
||||
#define VALIDATE_HOMING_ENDSTOPS
|
||||
|
|
@ -1429,7 +1448,7 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
|
|
@ -1442,7 +1461,7 @@
|
|||
// When enabled Marlin will send a busy status message to the host
|
||||
// every couple of seconds when it can't accept commands.
|
||||
//
|
||||
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
//#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||||
#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
|
||||
|
||||
|
|
@ -1460,7 +1479,7 @@
|
|||
|
||||
// Preheat Constants
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_HOTEND 200
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
|
|
@ -1480,7 +1499,7 @@
|
|||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
|
|
@ -1642,7 +1661,7 @@
|
|||
* you must uncomment the following option or it won't work.
|
||||
*
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: SPI SPEED
|
||||
|
|
@ -1659,7 +1678,7 @@
|
|||
*
|
||||
* Use CRC checks and retries on the SD communication.
|
||||
*/
|
||||
//#define SD_CHECK_AND_RETRY
|
||||
#define SD_CHECK_AND_RETRY
|
||||
|
||||
/**
|
||||
* LCD Menu Items
|
||||
|
|
@ -1676,13 +1695,13 @@
|
|||
// This option overrides the default number of encoder pulses needed to
|
||||
// produce one step. Should be increased for high-resolution encoders.
|
||||
//
|
||||
//#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_PULSES_PER_STEP 1
|
||||
|
||||
//
|
||||
// Use this option to override the number of step signals required to
|
||||
// move between next/prev menu items.
|
||||
//
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 5
|
||||
|
||||
/**
|
||||
* Encoder Direction Options
|
||||
|
|
@ -1893,7 +1912,7 @@
|
|||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// ReprapWorld Graphical LCD
|
||||
|
|
@ -2229,12 +2248,12 @@
|
|||
* Set this manually if there are extra servos needing manual control.
|
||||
* Leave undefined or set to 0 to entirely disable the servo subsystem.
|
||||
*/
|
||||
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
||||
#define NUM_SERVOS 2 // Servo index starts with 0 for M280 command
|
||||
|
||||
// (ms) Delay before the next move will start, to give the servo time to reach its target angle.
|
||||
// 300ms is a good value but you can try less delay.
|
||||
// If the servo can't reach the requested position, increase it.
|
||||
#define SERVO_DELAY { 300 }
|
||||
#define SERVO_DELAY { 300, 300 }
|
||||
|
||||
// Only power servos during movement, otherwise leave off to prevent jitter
|
||||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
|
|
|||
|
|
@ -149,8 +149,8 @@
|
|||
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
#define THERMAL_PROTECTION_PERIOD 50 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 3 // Degrees Celsius
|
||||
|
||||
//#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
|
||||
#if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
|
||||
|
|
@ -169,7 +169,7 @@
|
|||
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
|
||||
* below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 20 // Seconds
|
||||
#define WATCH_TEMP_PERIOD 50 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
|
|
@ -177,7 +177,7 @@
|
|||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 50 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
/**
|
||||
|
|
@ -715,7 +715,7 @@
|
|||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
|
||||
// Time can be set by M18 and M84.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 120
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 0 // usually set to 120 seconds
|
||||
#define DISABLE_INACTIVE_X true
|
||||
#define DISABLE_INACTIVE_Y true
|
||||
#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished.
|
||||
|
|
@ -1011,7 +1011,7 @@
|
|||
|
||||
//#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
|
||||
|
||||
#define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
|
||||
#define EVENT_GCODE_SD_STOP "G27" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
|
||||
|
||||
/**
|
||||
* Continue after Power-Loss (Creality3D)
|
||||
|
|
@ -1095,7 +1095,7 @@
|
|||
* On print completion the LCD Menu will open with the file selected.
|
||||
* You can just click to start the print, or navigate elsewhere.
|
||||
*/
|
||||
//#define SD_REPRINT_LAST_SELECTED_FILE
|
||||
#define SD_REPRINT_LAST_SELECTED_FILE
|
||||
|
||||
/**
|
||||
* Auto-report SdCard status with M27 S<seconds>
|
||||
|
|
@ -1424,15 +1424,15 @@
|
|||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 1 // Babysteps are very small. Increase for faster motion.
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 3 // Babysteps are very small. Increase for faster motion.
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 3
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
|
|
@ -1689,7 +1689,7 @@
|
|||
// For debug-echo: 128 bytes for the optimal speed.
|
||||
// Other output doesn't need to be that speedy.
|
||||
// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
|
||||
#define TX_BUFFER_SIZE 0
|
||||
#define TX_BUFFER_SIZE 32
|
||||
|
||||
// Host Receive Buffer Size
|
||||
// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
|
||||
|
|
@ -1823,7 +1823,7 @@
|
|||
* Requires NOZZLE_PARK_FEATURE.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
|
|
@ -1861,7 +1861,7 @@
|
|||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
|
|
@ -2749,7 +2749,7 @@
|
|||
* - M206 and M428 are disabled.
|
||||
* - G92 will revert to its behavior from Marlin 1.0.
|
||||
*/
|
||||
//#define NO_WORKSPACE_OFFSETS
|
||||
#define NO_WORKSPACE_OFFSETS
|
||||
|
||||
/**
|
||||
* Set the number of proportional font spaces required to fill up a typical character space.
|
||||
|
|
@ -2758,7 +2758,7 @@
|
|||
* For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
|
||||
* Otherwise, adjust according to your client and font.
|
||||
*/
|
||||
#define PROPORTIONAL_FONT_RATIO 1.0
|
||||
#define PROPORTIONAL_FONT_RATIO 1.5
|
||||
|
||||
/**
|
||||
* Spend 28 bytes of SRAM to optimize the GCode parser
|
||||
|
|
@ -2821,8 +2821,8 @@
|
|||
#define USER_DESC_4 "Heat Bed/Home/Level"
|
||||
#define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
|
||||
|
||||
#define USER_DESC_5 "Home & Info"
|
||||
#define USER_GCODE_5 "G28\nM503"
|
||||
//#define USER_DESC_5 "Home & Info"
|
||||
//#define USER_GCODE_5 "G28\nM503"
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue