diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 0fa70a11c7..f8ccaeed77 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index df564a49d4..b725d6fc35 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index cdf3db6c27..484ba7e235 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index 0600b6f4e7..eab1d005e1 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index 3c653d26d8..cda0d03ec4 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -749,15 +749,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 8edcd1f89c..5037fa3b04 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -749,15 +749,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 6e91812f1c..c404992cb8 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 9831e49dca..230dc332df 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index 1cd2ac00cd..7adc47619b 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index f4d7930b91..cbba9e041d 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index a92f1a7fea..0ec029e081 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index c930a3a41d..df3817f8b9 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -693,15 +693,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 22dcc04d25..7c3b85e758 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -693,15 +693,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h index 7635e8799f..3504d7afea 100644 --- a/config/examples/Anet/A9/Configuration.h +++ b/config/examples/Anet/A9/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index c0a5ae080a..62e78225a7 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h index 39a1579a62..004ed3d3be 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h index cc2f7a0058..bb06bf2974 100644 --- a/config/examples/Anet/E16/Stock/Configuration.h +++ b/config/examples/Anet/E16/Stock/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET4+/Configuration.h b/config/examples/Anet/ET4+/Configuration.h index dd111ceb01..a54eeb58cd 100644 --- a/config/examples/Anet/ET4+/Configuration.h +++ b/config/examples/Anet/ET4+/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET4-Pro/Configuration.h b/config/examples/Anet/ET4-Pro/Configuration.h index 377d8914fc..87a7db19a1 100644 --- a/config/examples/Anet/ET4-Pro/Configuration.h +++ b/config/examples/Anet/ET4-Pro/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h index 87a452d3b7..3db18e4ea7 100644 --- a/config/examples/Anet/ET4/Configuration.h +++ b/config/examples/Anet/ET4/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET4X/Configuration.h b/config/examples/Anet/ET4X/Configuration.h index f3b89b5cc9..585e3cb117 100644 --- a/config/examples/Anet/ET4X/Configuration.h +++ b/config/examples/Anet/ET4X/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET5-Pro/Configuration.h b/config/examples/Anet/ET5-Pro/Configuration.h index 4ae532ee44..8daa94ac0b 100644 --- a/config/examples/Anet/ET5-Pro/Configuration.h +++ b/config/examples/Anet/ET5-Pro/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET5/Configuration.h b/config/examples/Anet/ET5/Configuration.h index a2efa55c6c..65911b87ed 100644 --- a/config/examples/Anet/ET5/Configuration.h +++ b/config/examples/Anet/ET5/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Anet/ET5X/Configuration.h b/config/examples/Anet/ET5X/Configuration.h index 4e4343ae2e..0993ecb657 100644 --- a/config/examples/Anet/ET5X/Configuration.h +++ b/config/examples/Anet/ET5X/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h index c1a240a6ae..2aedbdafe6 100644 --- a/config/examples/AnyCubic/Chiron/Configuration.h +++ b/config/examples/AnyCubic/Chiron/Configuration.h @@ -695,15 +695,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h index 65d4e00f51..247dd6db06 100644 --- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h index 11d2be85d1..c9dfc09a7f 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h index 21a5cdb74d..6ffd987516 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h index f4826e2cfe..480fb7a504 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration.h @@ -714,15 +714,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index a07bf1dafb..9cebf3e5b8 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index e3faa4c8ee..6b8b9a5652 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Genius Pro/Configuration.h b/config/examples/Artillery/Genius Pro/Configuration.h index d8bc68f520..da736b13c4 100644 --- a/config/examples/Artillery/Genius Pro/Configuration.h +++ b/config/examples/Artillery/Genius Pro/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Genius/BLTouch/Configuration.h b/config/examples/Artillery/Genius/BLTouch/Configuration.h index 0994591126..fc02c00350 100644 --- a/config/examples/Artillery/Genius/BLTouch/Configuration.h +++ b/config/examples/Artillery/Genius/BLTouch/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Genius/V1/Configuration.h b/config/examples/Artillery/Genius/V1/Configuration.h index 5d17b0cf8b..a119eb3e2b 100644 --- a/config/examples/Artillery/Genius/V1/Configuration.h +++ b/config/examples/Artillery/Genius/V1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Hornet/Configuration.h b/config/examples/Artillery/Hornet/Configuration.h index e88988b852..3df60b47ef 100644 --- a/config/examples/Artillery/Hornet/Configuration.h +++ b/config/examples/Artillery/Hornet/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h index ac0388abe7..50f082607f 100644 --- a/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration.h @@ -701,15 +701,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h index 81af6d93c4..cb57159b59 100644 --- a/config/examples/Artillery/Sidewinder X1/V1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/V1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Artillery/Sidewinder X2/Configuration.h b/config/examples/Artillery/Sidewinder X2/Configuration.h index 65d1de645f..a9286b9869 100644 --- a/config/examples/Artillery/Sidewinder X2/Configuration.h +++ b/config/examples/Artillery/Sidewinder X2/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 261703409d..2cb73f4609 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index c1386397a4..feeb28a409 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 3df3a18fb0..32a2b80804 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h index 69b02a04bb..967126fdd2 100644 --- a/config/examples/BIQU/B1 - SKR 1.4/Configuration.h +++ b/config/examples/BIQU/B1 - SKR 1.4/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIQU/B1 - SKR 2/Configuration.h b/config/examples/BIQU/B1 - SKR 2/Configuration.h index 0f52ca34db..98b869154d 100644 --- a/config/examples/BIQU/B1 - SKR 2/Configuration.h +++ b/config/examples/BIQU/B1 - SKR 2/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIQU/B1 SE Plus/Configuration.h b/config/examples/BIQU/B1 SE Plus/Configuration.h index 36ec87f379..bb78220997 100644 --- a/config/examples/BIQU/B1 SE Plus/Configuration.h +++ b/config/examples/BIQU/B1 SE Plus/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIQU/BX/Configuration.h b/config/examples/BIQU/BX/Configuration.h index f93305dff9..9fc09c8317 100644 --- a/config/examples/BIQU/BX/Configuration.h +++ b/config/examples/BIQU/BX/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BIQU/Thunder Standard/Configuration.h b/config/examples/BIQU/Thunder Standard/Configuration.h index 873b4a0d3b..5a557d2c45 100644 --- a/config/examples/BIQU/Thunder Standard/Configuration.h +++ b/config/examples/BIQU/Thunder Standard/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 3079fb2fd9..eef770166f 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 939c7f1f75..183a58951f 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -704,15 +704,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 51ee0a08f1..c30cb24329 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/CTC/A13/Configuration.h b/config/examples/CTC/A13/Configuration.h index b051df2ee2..699aea14d4 100644 --- a/config/examples/CTC/A13/Configuration.h +++ b/config/examples/CTC/A13/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/CTC/Bizer/Configuration.h b/config/examples/CTC/Bizer/Configuration.h index d3bd18d4e2..cd02679762 100644 --- a/config/examples/CTC/Bizer/Configuration.h +++ b/config/examples/CTC/Bizer/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index 225b112e9b..f854d43ec3 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index c80e3bda6f..a32b77a7fd 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -702,15 +702,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index 323769120c..f9871de774 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 0eb0333d38..fbb7e1c412 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index fee80f7fa3..f6dc78d586 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h index e955cdb41c..ff83841251 100644 --- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -700,15 +700,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h index b4ea40edad..351b3a693a 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h @@ -700,15 +700,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h index df13449727..b8d1f1ce41 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h index 1d060b443f..31ded09e51 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h index 6515fa2a31..e5ab0fb61f 100644 --- a/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h +++ b/config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h index 157cef724a..f78954cf57 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h index 0317d9aa21..6b083fa666 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h +++ b/config/examples/Creality/CR-10 S5/CrealityV2.2-BLTouch/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index 63cdcc8bbe..2aa1a4b362 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -698,15 +698,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10 V3/Configuration.h b/config/examples/Creality/CR-10 V3/Configuration.h index d9d1876cf5..60998add2e 100644 --- a/config/examples/Creality/CR-10 V3/Configuration.h +++ b/config/examples/Creality/CR-10 V3/Configuration.h @@ -698,15 +698,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h index 1cb76fc0a3..1d702a5740 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h index 82a323d77d..2857a7abf7 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h index 32fd762fad..ae9213a2f4 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h index 1e9028c4d6..5bbe40cb8b 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h index 33a27d2ed5..789114c339 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h index bfd72a3cba..12f85fbce9 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h index a0897c4cf9..35c89caedc 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index 01ecc8ffec..0b06eb8082 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 297b28a6c3..aae9bebe6e 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-30 PrintMill/Configuration.h b/config/examples/Creality/CR-30 PrintMill/Configuration.h index b03eb829a0..a833839e2f 100644 --- a/config/examples/Creality/CR-30 PrintMill/Configuration.h +++ b/config/examples/Creality/CR-30 PrintMill/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h index 98313f5860..5c51682b16 100644 --- a/config/examples/Creality/CR-6 SE/Configuration.h +++ b/config/examples/Creality/CR-6 SE/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 33019ce97e..28b4721e35 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h index eadc760a0e..0708f170b5 100644 --- a/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h +++ b/config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index b9be6d3f2d..f38cbfecca 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Max/Configuration.h b/config/examples/Creality/Ender-3 Max/Configuration.h index 0b5cedc9d4..9a3d2afce6 100644 --- a/config/examples/Creality/Ender-3 Max/Configuration.h +++ b/config/examples/Creality/Ender-3 Max/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h index 6fdeec0201..6f79e22e12 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h index 727860ff3d..15043c4524 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index d81a1d4909..d8028ae2cb 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h index 1420fc2750..37a5b551ac 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h index 923575b616..d53aff55bf 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h index 5a3e7bb307..ee3f98eb24 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h index b9af23b49c..f304872813 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h index 9e5e4c9047..62b9fcda4a 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 S1/Configuration.h b/config/examples/Creality/Ender-3 S1/Configuration.h index 518fa09829..d075268c42 100644 --- a/config/examples/Creality/Ender-3 S1/Configuration.h +++ b/config/examples/Creality/Ender-3 S1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h index a84574ccda..4693f99f84 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/CrealityUI/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h index 730bc5514c..e1cc22ad1c 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR E3 Turbo/MarlinUI/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h index 1b80bc4ebc..3a9e54eb2a 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/CrealityUI/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h index 82299b3a9e..73b5c9a237 100644 --- a/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/BigTreeTech SKR Mini E3 v3/MarlinUI/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h index da80a2e8e7..0b2d808673 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/CrealityUI/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h index 3ddf06e375..a6f0dd4e97 100644 --- a/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/CrealityV422/MarlinUI/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h index 4d5ddb1646..97046aebe5 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h index 64880bb819..fec458ff97 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h index c74694bec3..3422a84ce3 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h index f4d45f7e8d..a68e047e41 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h index 350e738bc7..23a601577f 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h index c52a0e3e7e..cc1778bf0a 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index a02625f9db..1a2d553a8f 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index afd6b3d12c..cc3dc25d74 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index f95c27535d..d06e25fa07 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h index e96f5949a7..1aa6c349cd 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index 4f5224aaee..aef9a94c15 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h index adb20b0a9a..c15a482b9a 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h index 02e6a8d814..e5763106f3 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index eba654140e..ca4fcb329b 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 81b85d501c..0bb391c387 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h index e461d75d6b..6b886c058c 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index a587871f40..6011215bdf 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index 7f7274cb35..8e83b722fc 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index 9a20d1aa50..548a055711 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h index 468b613619..910690cda9 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h index afd0041f4a..7c4236284c 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h index c9c498af47..1465ce11fd 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h index 9dec91cc87..4080b9b86b 100644 --- a/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h +++ b/config/examples/Creality/Ender-3/TH3D EZBoard Lite V2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index eb00de0782..449d17e00f 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h index f46ddedbf3..cc99fadfc4 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h index 5111673466..8d65fd25d3 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h index ed17ff3607..b7110d5ded 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h index 879d7f5f94..2cb834e9f3 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h index e5f051a210..f2acde4226 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h index e65d409737..2e5484a3e8 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h index 03adf85412..bc77bb9961 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h index c5a5f1d46c..87483733e9 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h index d46a27139e..700a6eb8fb 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h index 9fcbb0e56d..0234af1338 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index 27b7409db5..3ce996581c 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h index 8d2f6b75c5..79ff35209f 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h index 0d07514d48..d4f5c42dda 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Creality/Ender-6/Configuration.h b/config/examples/Creality/Ender-6/Configuration.h index 1c5dd9cdc6..362f17bd69 100644 --- a/config/examples/Creality/Ender-6/Configuration.h +++ b/config/examples/Creality/Ender-6/Configuration.h @@ -693,15 +693,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 6f693bb5e3..211a6cfb8f 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index 0e08c53655..123abdc07f 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index 9c661325b3..483fe9d3a3 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h index 01e291e261..200013548e 100644 --- a/config/examples/EasyThreeD/ET4000PLUS/Configuration.h +++ b/config/examples/EasyThreeD/ET4000PLUS/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 39f7154eaa..1b2df91f3c 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Elegoo/Neptune 2/Configuration.h b/config/examples/Elegoo/Neptune 2/Configuration.h index e466776cad..5375445af3 100644 --- a/config/examples/Elegoo/Neptune 2/Configuration.h +++ b/config/examples/Elegoo/Neptune 2/Configuration.h @@ -726,15 +726,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Eryone/Thinker SE/Configuration.h b/config/examples/Eryone/Thinker SE/Configuration.h index c7789ffaa5..3795fff43a 100644 --- a/config/examples/Eryone/Thinker SE/Configuration.h +++ b/config/examples/Eryone/Thinker SE/Configuration.h @@ -698,15 +698,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Eryone/Thinker V2/Configuration.h b/config/examples/Eryone/Thinker V2/Configuration.h index fe0bc1b927..428e299893 100644 --- a/config/examples/Eryone/Thinker V2/Configuration.h +++ b/config/examples/Eryone/Thinker V2/Configuration.h @@ -697,15 +697,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 97c194b3c5..f70b1b6ec8 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 51c2e3d661..09e5a800cd 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index 82bafeaa13..47a01afa5b 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 928af15b40..bd9d68e5ee 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index 2a515203dd..55193e08ed 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index c4a93240d2..930b366eb1 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index 02a8f9d6d2..ae5562eff4 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FlyingBear/P902/Configuration.h b/config/examples/FlyingBear/P902/Configuration.h index b24666da2d..d24a20ae8b 100644 --- a/config/examples/FlyingBear/P902/Configuration.h +++ b/config/examples/FlyingBear/P902/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index 7828ae4b66..e27cb7d8b1 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FoamCutter/Configuration.h b/config/examples/FoamCutter/Configuration.h index 88c4fbe41f..912cb6132d 100644 --- a/config/examples/FoamCutter/Configuration.h +++ b/config/examples/FoamCutter/Configuration.h @@ -689,15 +689,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 8052174784..b1a756643b 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 6d0f99cee8..0ceee21e83 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -749,15 +749,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 7fed366c1d..e1c70295e9 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index bd5ee3f476..366f30a299 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index 7d01e2c664..38c0d7505e 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index 8d60e4148e..9f58c810d4 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h index 905f9fcc5d..0d7bb47d98 100644 --- a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h index 6b36923fb5..99cb2dc1a9 100644 --- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10PRO/Configuration.h b/config/examples/Geeetech/A10PRO/Configuration.h index 7c47225bbe..5fa48840d5 100644 --- a/config/examples/Geeetech/A10PRO/Configuration.h +++ b/config/examples/Geeetech/A10PRO/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h index 4a44c29be8..03b16be013 100644 --- a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h +++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h index 552013edbc..3f26a8cd86 100644 --- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h +++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index 4ac0876d58..822834ee8f 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index beb463cb59..7e5a7d6b7a 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index 6075a2e26d..1455285307 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 2a246c1781..3421209ffe 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A30M/Configuration.h b/config/examples/Geeetech/A30M/Configuration.h index 156d2182c6..6b7d49365f 100644 --- a/config/examples/Geeetech/A30M/Configuration.h +++ b/config/examples/Geeetech/A30M/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/A30T/Configuration.h b/config/examples/Geeetech/A30T/Configuration.h index 1964e18319..f05ce1c5ba 100644 --- a/config/examples/Geeetech/A30T/Configuration.h +++ b/config/examples/Geeetech/A30T/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index 9465c4d76d..3178e1c860 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index f3cdf2d541..131131cdcf 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index 054c7e7258..b401732c69 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 5eb2831931..38f09aa6c4 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 6f4941bc99..d8a0093fbe 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index 82d3f2b295..f75dda93c8 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 0b73b5b15f..b1039c4cc5 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index 16586cad1c..f116542962 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 2c01474fc7..21240640ad 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index 5faf2e599e..78109eb27f 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index fbb64a06c4..a1fc7a8a96 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index c8b7033852..89a5e69ed7 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index c6367710ec..aab4ab937c 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 6653149b1f..ac9cbbebc3 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 72d49aed09..db6bce370a 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -688,15 +688,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Index/REV_03/Configuration.h b/config/examples/Index/REV_03/Configuration.h index 36258f4963..0a3a769557 100644 --- a/config/examples/Index/REV_03/Configuration.h +++ b/config/examples/Index/REV_03/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index cf5defce50..8d11a7e443 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h index 155d7bbb01..fa610d06cb 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index e1c476ef19..9279a69f59 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index f321ff0c62..cd29cc9f9a 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index b79c6f098c..a95a859f8e 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index 5b4844cc57..f585998ce2 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index c13399e4a8..41eebbba26 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index 2f4cbe1872..939e7b0e08 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Kingroon/KP3S/Configuration.h b/config/examples/Kingroon/KP3S/Configuration.h index ef28ad1ed8..132d18c15b 100644 --- a/config/examples/Kingroon/KP3S/Configuration.h +++ b/config/examples/Kingroon/KP3S/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Labists/ET4/Configuration.h b/config/examples/Labists/ET4/Configuration.h index f83dcfacfe..56ef6767af 100644 --- a/config/examples/Labists/ET4/Configuration.h +++ b/config/examples/Labists/ET4/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/LulzBot/TAZ4/Configuration.h b/config/examples/LulzBot/TAZ4/Configuration.h index 68831839be..13aa795b9e 100644 --- a/config/examples/LulzBot/TAZ4/Configuration.h +++ b/config/examples/LulzBot/TAZ4/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index 29d60805fc..f2e5389e09 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h index cccd1a45ee..8dc7818393 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index f5e7b87414..10d090b9f7 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 5488a4c97e..2f88862b1b 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -699,15 +699,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Malyan/M180/Configuration.h b/config/examples/Malyan/M180/Configuration.h index 6c8aedb6e9..9031cac648 100644 --- a/config/examples/Malyan/M180/Configuration.h +++ b/config/examples/Malyan/M180/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index 481d9a651d..24a9e46a63 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 04c04615ea..46449ea290 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index 6b004cbb7f..48da3eff44 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index c86cb713da..8557cfd3ed 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index e57ea74163..36fa5b9def 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -696,15 +696,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index cad3f825a1..de93631c07 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index e9c2222ddc..2fbb8a6b37 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index 369c3c1e41..be08b9c540 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Nextion/Configuration.h b/config/examples/Nextion/Configuration.h index ea5f69538c..e8d30b7503 100644 --- a/config/examples/Nextion/Configuration.h +++ b/config/examples/Nextion/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index 5f1709512d..445f6297ac 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Polargraph/Configuration.h b/config/examples/Polargraph/Configuration.h index 59e6c552c3..b715c07fab 100644 --- a/config/examples/Polargraph/Configuration.h +++ b/config/examples/Polargraph/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index 8569019905..0bc5faf14c 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index 06176f2a6b..a17ac4697e 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Prusa/MK3/Configuration.h b/config/examples/Prusa/MK3/Configuration.h index 10500760e7..8b49e1a5e5 100644 --- a/config/examples/Prusa/MK3/Configuration.h +++ b/config/examples/Prusa/MK3/Configuration.h @@ -714,15 +714,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index 27d34a2936..3e4f3b99be 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -707,15 +707,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index 0efdde1e47..25eb3c90a4 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h index 41bc126607..029869e936 100644 --- a/config/examples/Raiscube/A8r/Configuration.h +++ b/config/examples/Raiscube/A8r/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 9edf39e284..d10686f349 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index 700550d62e..bfa70de127 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -695,15 +695,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index 31615629a8..69dda22013 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -695,15 +695,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 4457dd35c1..5579aa0259 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -695,15 +695,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 8bfa2f7d14..d254a2663c 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 52a96e2ed4..2052a455a4 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index e4906f6b1d..e234aa32f0 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -703,15 +703,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index cd8b9a91ac..573cd94233 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 948cd1d260..c9afabd7fb 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -736,15 +736,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 8991e18a11..f69196428e 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -736,15 +736,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index dc3f386bc3..b7082cb24a 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index 4a78e79289..aba2785b9f 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 2788acedd4..227c574ffa 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Simulator/Configuration.h b/config/examples/Simulator/Configuration.h index 57206768ca..5871913dfa 100644 --- a/config/examples/Simulator/Configuration.h +++ b/config/examples/Simulator/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h index 655696d541..830e6507cc 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR E3 Turbo/Configuration.h @@ -694,15 +694,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h index d48a3ea9cc..2261ab3b32 100644 --- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h index 1aaf70982d..6b9dcf93ab 100644 --- a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h index ac664b6573..f789bae184 100644 --- a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h +++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Sunlu/S8/Configuration.h b/config/examples/Sunlu/S8/Configuration.h index aaf9b6ab60..77fef56679 100644 --- a/config/examples/Sunlu/S8/Configuration.h +++ b/config/examples/Sunlu/S8/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration.h b/config/examples/TPARA/AXEL_TPARA/Configuration.h index cb7c1ab1c1..0ed50d982f 100644 --- a/config/examples/TPARA/AXEL_TPARA/Configuration.h +++ b/config/examples/TPARA/AXEL_TPARA/Configuration.h @@ -711,15 +711,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index 1d57dc3c0c..7963381bce 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 422b782180..7f1d280402 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index 2e2f5567d0..abaa0d056c 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 4d81e21a66..3d7243c3c0 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index 30a261c628..d4176ad27d 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 5c57b553b5..a91afcaf12 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -724,15 +724,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index eb028229c7..5b13016b75 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index b63b68dfa3..488f3345cd 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index df75313881..517e9921fc 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -699,15 +699,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 1be492ef3e..7245bde5bd 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/X5SA-2E/Configuration.h b/config/examples/Tronxy/X5SA-2E/Configuration.h index 7907e9c103..ca476361e3 100644 --- a/config/examples/Tronxy/X5SA-2E/Configuration.h +++ b/config/examples/Tronxy/X5SA-2E/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index a830e1ddb8..52b944cc58 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 695b6f39b6..381e8575e3 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -697,15 +697,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Two Trees/BlueR Plus/Configuration.h b/config/examples/Two Trees/BlueR Plus/Configuration.h index b908409121..13e8b9fbf7 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h index bb73eaf605..09239c06d5 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h @@ -704,15 +704,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h index 552926647e..84219425aa 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h @@ -705,15 +705,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h index 9aa0222b9c..92eeb999e3 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h @@ -704,15 +704,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h index d962ad8001..b57507e785 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h @@ -697,15 +697,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h index cb92898540..21b476392f 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h @@ -704,15 +704,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 8923476015..91473a6239 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index 2d0406851e..be68a6fa00 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Ultimaker/Ultimaker 2/Configuration.h b/config/examples/Ultimaker/Ultimaker 2/Configuration.h index 067b57e949..880529b28e 100644 --- a/config/examples/Ultimaker/Ultimaker 2/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker 2/Configuration.h @@ -703,15 +703,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h index 108ae75763..7bed29c41b 100644 --- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h index 0524db0e15..4e9efab9d3 100644 --- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h +++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 0d56ffcf84..ec0f0c4b28 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Velleman/K8200 Upgraded/Configuration.h b/config/examples/Velleman/K8200 Upgraded/Configuration.h index 78a9f378b4..b918e88df4 100644 --- a/config/examples/Velleman/K8200 Upgraded/Configuration.h +++ b/config/examples/Velleman/K8200 Upgraded/Configuration.h @@ -718,15 +718,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index 13880f5e8c..9a1cbf72e7 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -722,15 +722,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 1f561874a5..9e7e3bc11b 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index 1af2c30f73..cc278ba98d 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 93ffa31912..33138fb900 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -704,15 +704,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index db906c2d59..ae8dc63129 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 114c49e63c..33893951ec 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 72a7102107..0f4aa31939 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index de2f8e872d..592e00d1de 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h index e2e12fb6c4..5a6114d26d 100644 --- a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Weedo/Tina2/V2/Configuration.h b/config/examples/Weedo/Tina2/V2/Configuration.h index 9df1602462..112a5aaca7 100644 --- a/config/examples/Weedo/Tina2/V2/Configuration.h +++ b/config/examples/Weedo/Tina2/V2/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Weedo/Tina2/V3/Configuration.h b/config/examples/Weedo/Tina2/V3/Configuration.h index cad8e24375..a4142f7c4a 100644 --- a/config/examples/Weedo/Tina2/V3/Configuration.h +++ b/config/examples/Weedo/Tina2/V3/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index 6ac486c359..cc71aecac7 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index d29c6f7cfe..742ea6c5db 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index 7b47a012b2..c9ec5a86b7 100644 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -693,15 +693,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index 52f925ae27..592083f907 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -692,15 +692,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index 2c922872a3..b85c7b656e 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -698,15 +698,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 2811ff79a8..c99c4380df 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -701,15 +701,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index b8a8a0a51e..51e4b0aa6e 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index ffad07cc18..5f30f2352b 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index 2d93fff74b..95385479b7 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -688,15 +688,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h index f81cbe84c1..2df622f787 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h index d3a5f1ba39..c529661ab5 100644 --- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h +++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index 002190ae43..dcb0e8da8e 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h index 4e4463a00e..412902bc57 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index b406855f83..eb26016ad1 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index 60373d18fe..90d021f516 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index d82715dde5..f669186ae9 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index 4cceedfe94..faabf716a7 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index 5c0ddb451e..6e8265332e 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index f7dabb6253..f8e26b2f3b 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index 60b31485cd..9ec8dfdc92 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index ff7723cfc1..895acb0e11 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index d7072825f6..7aa75fe2c5 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -687,15 +687,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index 4881cc4a2c..4c7d057185 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index 41c467b335..67336d89c2 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 3f7871b6b2..bead02e712 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -682,15 +682,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 7d4ea4f1b5..1cd8009304 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index 5873e91cc5..df8df4dc7c 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index a18da50aef..549921420a 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -681,15 +681,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index ae3e05dbd4..516ebe1c03 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -686,15 +686,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index d53289e2d3..c6e31a42e7 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -687,15 +687,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 0bfdf13399..c30cf1bda7 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -697,15 +697,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h index c01f3ab526..f52f472594 100644 --- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h +++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h @@ -677,15 +677,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index dfa605918c..7c8684feef 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -690,15 +690,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index f9354746f2..4d35038398 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -691,15 +691,15 @@ //#define MPC_FAN_0_ACTIVE_HOTEND #endif - #define FILAMENT_HEAT_CAPACITY_PERMM 5.6e-3f // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). - //#define FILAMENT_HEAT_CAPACITY_PERMM 3.6e-3f // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). + #define FILAMENT_HEAT_CAPACITY_PERMM { 5.6e-3f } // 0.0056 J/K/mm for 1.75mm PLA (0.0149 J/K/mm for 2.85mm PLA). + //#define FILAMENT_HEAT_CAPACITY_PERMM { 3.6e-3f } // 0.0036 J/K/mm for 1.75mm PETG (0.0094 J/K/mm for 2.85mm PETG). // Advanced options #define MPC_SMOOTHING_FACTOR 0.5f // (0.0...1.0) Noisy temperature sensors may need a lower value for stabilization. #define MPC_MIN_AMBIENT_CHANGE 1.0f // (K/s) Modeled ambient temperature rate of change, when correcting model inaccuracies. #define MPC_STEADYSTATE 0.5f // (K/s) Temperature change rate for steady state logic to be enforced. - #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center just above the surface. + #define MPC_TUNING_POS { X_CENTER, Y_CENTER, 1.0f } // (mm) M306 Autotuning position, ideally bed center at first layer height. #define MPC_TUNING_END_Z 10.0f // (mm) M306 Autotuning final Z position. #endif